Search Documents

By H. H. Kaveler, W. R. Evans, Jack Tarner

The geological features, development history and engineering detail of the Shuler Field and the results of approximately two years of unitized operation of the Shuler Jones Sand Pool, were discussed in a prior publication.' The purpose of this paper is to present the results of pressure maintenance in the Shuler Jones Sand Pool after nine years of unit operation. GENERAL INFORMATION The Shuler Jones Sand Pool is located in and about Section 18, Township 18 South, Range 17 West, Union County, Ark. The pool was discovered .in September, 1937, unitized in February, 1941, and subjected to gas injection operations in July, 1941. Water was first returned to the reservoir in July, 1944. The reservoir is an anticlinal trap covering about 4,000 acres. The 154,000 acre-ft of sandstone initially consisted of approximately 150,000 acre-ft of productive oil zone and 4,000 acre-ft of gas-cap. The average depth of production is 7,400 ft. Maximum closure of the reservoir is 135 ft and the oil column lies between a gas-oil contact at -7,270 ft and a water-oil contact at -7,370 to -7,380 ft. The field is approximately four miles long. east and .west, and one and one-half miles wide. The sand grains are angular and vary from fine to medium size. The porosity of the sandstone averages 20.2 per cent. The specific permeability averages 400 md. Some zones have as high as 30 per cent porosity and specific permeability of 4,000 md. The reservoir rock is not uniform in character but consists of sandstone zones interspersed with shale. The variation in rock characteristics is evident in the electric log and core analyses presented in the original publication. Asphalt present in the pore space of the sandstone limited the reservoir to the southeast and apparently blocked any encroachment of water from that direction. The initial reservoir pressure at a subsea depth of 7,300 ft was 3,520 psi. The reservoir temperature was 198ºF. Initially, the solution gas volume was 765 cu ft per bbl and the reservoir volume factor was 1.45. The gas solubility and formation-volume-factors of the reservoir liquid are related with reservoir pressures above 300 psi as follows: Solution gas, cu ft per cu ft, S = 0.0334 P + 18.65 Formation volume factor of reservoir oil, FVF = 8.0 x 10 -5 P + 1.168 Gas volume factor, standard cu ft of gas equivalent to one cu ft of gas at reservoir conditions of temperature and pressure, F = .062 P - 4 Pressure (P) measured in psia. The equation for the gas volume factor presented above is based on a direct measurement of a sample of the gas and is a correction of that used in the original paper. The gravity of the oil produced is from 32 to 34" API. CALCULATION OF INITIAL OIL IN PLACE The Jones Sand production history is interesting because it lends itself to analysis by material balance. Production statistics from discovery of the Jones Sand through 1949 and material balance calculations of the initial stock tank oil in place are shown in Table I. The usual procedure in testing the application of material balance calculations is to compute the apparent initial volume of oil in place, using production and pressure information obtained at different time periods. If the apparent oil in place volumes computed increase with successive time periods, water encroachment is indicated and approximations must be mads to correct for its influence. The first requirement in utilizing such calculations is reliable reservoir pressure, accumulated gas, oil and water production, and PVT data. Calculations of apparent oil in place in the Jones Pool, based on field data

Jan 1, 1951

By W. R. Evans, H. H. Kaveler, Jack Tarner

The geological features, development history and engineering detail of the Shuler Field and the results of approximately two years of unitized operation of the Shuler Jones Sand Pool, were discussed in a prior publication.' The purpose of this paper is to present the results of pressure maintenance in the Shuler Jones Sand Pool after nine years of unit operation. GENERAL INFORMATION The Shuler Jones Sand Pool is located in and about Section 18, Township 18 South, Range 17 West, Union County, Ark. The pool was discovered .in September, 1937, unitized in February, 1941, and subjected to gas injection operations in July, 1941. Water was first returned to the reservoir in July, 1944. The reservoir is an anticlinal trap covering about 4,000 acres. The 154,000 acre-ft of sandstone initially consisted of approximately 150,000 acre-ft of productive oil zone and 4,000 acre-ft of gas-cap. The average depth of production is 7,400 ft. Maximum closure of the reservoir is 135 ft and the oil column lies between a gas-oil contact at -7,270 ft and a water-oil contact at -7,370 to -7,380 ft. The field is approximately four miles long. east and .west, and one and one-half miles wide. The sand grains are angular and vary from fine to medium size. The porosity of the sandstone averages 20.2 per cent. The specific permeability averages 400 md. Some zones have as high as 30 per cent porosity and specific permeability of 4,000 md. The reservoir rock is not uniform in character but consists of sandstone zones interspersed with shale. The variation in rock characteristics is evident in the electric log and core analyses presented in the original publication. Asphalt present in the pore space of the sandstone limited the reservoir to the southeast and apparently blocked any encroachment of water from that direction. The initial reservoir pressure at a subsea depth of 7,300 ft was 3,520 psi. The reservoir temperature was 198ºF. Initially, the solution gas volume was 765 cu ft per bbl and the reservoir volume factor was 1.45. The gas solubility and formation-volume-factors of the reservoir liquid are related with reservoir pressures above 300 psi as follows: Solution gas, cu ft per cu ft, S = 0.0334 P + 18.65 Formation volume factor of reservoir oil, FVF = 8.0 x 10 -5 P + 1.168 Gas volume factor, standard cu ft of gas equivalent to one cu ft of gas at reservoir conditions of temperature and pressure, F = .062 P - 4 Pressure (P) measured in psia. The equation for the gas volume factor presented above is based on a direct measurement of a sample of the gas and is a correction of that used in the original paper. The gravity of the oil produced is from 32 to 34" API. CALCULATION OF INITIAL OIL IN PLACE The Jones Sand production history is interesting because it lends itself to analysis by material balance. Production statistics from discovery of the Jones Sand through 1949 and material balance calculations of the initial stock tank oil in place are shown in Table I. The usual procedure in testing the application of material balance calculations is to compute the apparent initial volume of oil in place, using production and pressure information obtained at different time periods. If the apparent oil in place volumes computed increase with successive time periods, water encroachment is indicated and approximations must be mads to correct for its influence. The first requirement in utilizing such calculations is reliable reservoir pressure, accumulated gas, oil and water production, and PVT data. Calculations of apparent oil in place in the Jones Pool, based on field data

Jan 1, 1951

For handling rough rock, the shovel-train system is unexcelled. The ideal application is a physically large, but not excessively deep, open-pit mine from which the coarsely blasted ore and waste must be transported distances in excess of three miles. If, in addition, a high production rate is to be maintained, railroad haulage will probably afford a lower cost per ton transportation than will any other haulage method. Relatively gentle grades must be employed- usually 3% for uphill hauls and 4% for downhill hauls. The greater the differences in elevation the greater are the railroad track grade space requirements. By way of illustration, a 3% ramp out of a pit only 300 ft deep must be almost two miles long. Mainline track locations should be selected carefully so that the frequency of movements during the life of the mining operation is minimized. This applies both to ore and to waste haulageways. Such moves are not only expensive but difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semi-permanent trackage.

Jan 10, 1967

By J. A. SINGMASTERN

THE New Jersey Zinc Co.'s vertical retort plants are believed to have been in continuous operation through the whole year. At Palmerton metal purer than that made from the same ore in the old plant has been produced and has been able to compete successfully with very pure electrolytic metal in die castings and other special uses where extreme purity is worth money. A new plant using this process was put in production by the Grasselli Chemical Co. at Meadowbrook, W. Va., early in the summer. It is said to be working very satisfactorily. It is understood that this plant will not produce high-grade metal. Two patents issued to Bunce and Mahler (Nos. 1,749,126 and 1,749,127) describe a method of operating the vertical retort so that practically lead-free metal can be obtained from ores containing consider- able lead. The zinc vapors and other gases leaving the reaction zone are filtered through a column of material maintained at a temperature high enough to prevent much zinc from condensing. The filtering medium is either periodically or continuously changed.

Jan 1, 1931

By Wm. Reuben Webster

BRASS is an alloy of copper and zinc. The brasses (using this term to denote all useful proportions of the two constituents) are the most valuable and widely employed of all [ ] nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure brass containing 70 per cent copper and 30 per cent zinc. Fig. 3 shows the effect of annealing at various temperatures on the same alloy. This effect is somewhat modi [ ] fled by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity -the hot hammer test. Samples Y2 in. in diameter and ¾ in. long are placed in a suitable furnace. These are withdrawn one at a time at successively higher tempera¬tures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of' reduction in length of the cylinders are plotted against temperatures and give a comparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By Richard H. Rein, John Chipman

Liquid slags of the system SiO2-Ca0-MgO-A1~03 were equilibrated with liquid Fe-Si-C alloys in graphite or Sic crucibles at 1600°C in pure CO gas at atmospheric pressure, and the silicon content of both phases determined. Ternary slugs of the systern SiO2-CaO-A12O3 were also studied at 1550°C. The silicon content of the metal phase saturated with both graphite and SIC is 22.0pct at 1550°C and In the iron blast furnace, as in nearly all carbon-reduction processes, some silicon is transferred from slag to metal. The importance of this reaction is enhanced by its indirect effect on the transfer of sulfur from metal to slag, and this has stimulated a comprehensive research program on the equilibrium distribution of silicon between slag and metal. Earlier studies'-3 of this same problem provided data for calculation of the thermodynamic activities4 of the components in SiO,-CaO-A1,O3 slags. 22.4 pct at 1600°C. The temperature at which the phases cristobalite, gvaphite, $ SiC, liquid slag, Fe-Si-C alloy, and CO gas at 1 atm pressure can coexist in equilibrium was found to be 1533°C. The results agree well with earlier studies. They are shown graphically as lines of constant silicon cmtent in the metal which also are lines of constant SiO, activity in the slag.

Jan 1, 1963

By A. W. Hull

The new valves described in this article are the latest product of the Research Laboratories of the General Electric Co. Some of them are still in the laboratory stage, others have already found important applications. Some of the larger ones, which have graduated from the laboratory, are waiting for their apprenticeship in industry, there to refine their frailties and complete their preparation as electrical servants. The career that awaits them, though dimly foreseen, appears fascinating. And as surely as history repeats itself, scenes still more romantic, now beyond the horizon, will unfold as we approach them. This is the romance of science. Counting Electrons Let the smallest tube lead the march of review. It is a special Pliotron, designed to measure currents smaller than any yet detected. It goes by the unromantic name of Pliotron FP-54. Fig. 1 shows this miniature tube—miniature in performance rather than size, for it is the size of an ordinary radio receiving tube. Its appearance has nothing distinctive, except the quartz beads above and below the plate, which support the grid. They minimize insulation leakage. In principle, the FP-54 is like any grid-controlled high-vacuum electron tube; but in structure and operating characteristics it is entirely special. An extra "space-charge" grid, maintained at 3 volts positive with respect to the filament, holds back the small but pernicious current of positive ions emitted by the filament; the normal plate voltage is 6 volts, grid bias 3 volts, thoriated-tungsten filament temperature 1700" K., plate current 40 microamperes. These conditions are essential to the avoidance of grid-currents, which may consist not only of insulation leakage and positive ions from the hot filament and from residual gases, but of high-speed electrons from the filament, photo emission from the grid due to the light of the filament, and electron emission caused by X-rays generated by the impact of electrons on the plate.

Jan 1, 1932

By H. N. Thomson

GENERAL. THE Tooele plant of the International Smelting & Refining Co. is situated at the mouth of Pine canyon, Tooele county, Utah. It is connected with the main line of the San Pedro, Los Angeles & Salt Lake railroad by the Tooele Valley railway, and is about 7 miles from Tooele Junction. Fig. 1 is a general view of the plant. FIG. 1.-TOOELE PLANT OF THE INTERNATIONAL SMELTING & REFINING Co. The copper plant has been in operation since July, 1910, and the first blast furnace at the lead plant was blown in on Feb. 29, 1912. The location of the plant was selected on sloping ground with the idea of using gravity to the fullest extent and thus keeping labor at a minimum. Practically the entire plant is constructed of steel, reinforced concrete, and brick. Bingham ores, both lead and copper, are received over the Utah Consolidated Aerial Tramway. The tram buckets, each containing

Jan 7, 1913

By Richard A. Mullins, James J. Merle

Systematic sampling and analysis in coal-washing plants results in product control and economical operation. A well-organized laboratory system reduces operating costs and increases sales if the operating and sales companies make full use of information it supplies. The operating cost of a control laboratory is less than 1 pct per ton of coal produced. THE system of laboratory control as practiced by the Ayrshire group of mines was begun with the construction and organization of the first laboratory in conjunction with the completion of its first wash-ery in 1941. The primary purpose of this laboratory was to maintain a check on the quality of the coal produced from the washing plant. The laboratory was equipped to determine proximate analyses, float-and-sink tests, and screen analyses, and was staffed by a chemist. an assistant. and a technician. Members AIME, are Assistant Preparation Manager and Chief Chemist, respectively, Ayrshire Collieries Corp. and Subsidiaries, Danville, Ill. Joint AIME-ASME Fuels Conference. French Lick. October 1949. TP 2855 F. Discussion (2 copies) may be sent to Transactions AIME before June 30, 1950. Manuscript received Aug. 22, 1949. Soon it became apparent (1) that product control could be accomplished, (2) that a substantial reduction in operating costs could be effected by close control of coal losses in the rejects, and (3) that information furnished by the laboratory was of continuous value to the operating and sales companies. Consequently the laboratory function was expanded to supply them with additional data as required. As the parent company expanded and new mines were added, control laboratories were established at each mine equipped with washeries, and a central laboratory was maintained at one of the mines that was located equally convenient to all of them. A well-planned control laboratory assures production of a uniform, high-quality product. Whenever coal of substandard grade is loaded inadvertently, the sales company can be informed and the proper channel of distribution made. Conversely only constant and strict laboratory supervision can insure proper production of the various grades. Knowing the product, the producer can keep out of many customers' arguments that may be both awkward and expensive. Double checking between customers and mine laboratories have solved many disputes' Some nager insist On buying coal On the analysis basis only, with penalties for substandard coal and premiums for coal above normal quality. A substantial percentage of the coal sold by the Ayrshire group is of this nature. The usual procedure is for the customer to sample and analyze the coal as it is unloaded at the plant, and the mine laboratory samples it as it is loaded at the mine for subsequent analysis by the central laboratory. Only the unloaded moisture is considered, rather than the average of mine and plant moisture, and the buyer sends duplicate samples to the central mine laboratory for this determination. The average of the two analyses determines the price of coal at the mine. In this particular case, the laboratory plays an important part in increasing realization for two reasons: (1) every attempt is made to maintain plant efficiency and product quality as high as possible, (2) check on analyses and sampling by the buyer or seller.

Jan 1, 1951

By Richard A. Mullins, James J. Merle

Systematic sampling and analysis in coal-washing plants results in product control and economical operation. A well-organized laboratory system reduces operating costs and increases sales if the operating and sales companies make full use of information it supplies. The operating cost of a control laboratory is less than 1 pct per ton of coal produced. THE system of laboratory control as practiced by the Ayrshire group of mines was begun with the construction and organization of the first laboratory in conjunction with the completion of its first wash-ery in 1941. The primary purpose of this laboratory was to maintain a check on the quality of the coal produced from the washing plant. The laboratory was equipped to determine proximate analyses, float-and-sink tests, and screen analyses, and was staffed by a chemist. an assistant. and a technician. Members AIME, are Assistant Preparation Manager and Chief Chemist, respectively, Ayrshire Collieries Corp. and Subsidiaries, Danville, Ill. Joint AIME-ASME Fuels Conference. French Lick. October 1949. TP 2855 F. Discussion (2 copies) may be sent to Transactions AIME before June 30, 1950. Manuscript received Aug. 22, 1949. Soon it became apparent (1) that product control could be accomplished, (2) that a substantial reduction in operating costs could be effected by close control of coal losses in the rejects, and (3) that information furnished by the laboratory was of continuous value to the operating and sales companies. Consequently the laboratory function was expanded to supply them with additional data as required. As the parent company expanded and new mines were added, control laboratories were established at each mine equipped with washeries, and a central laboratory was maintained at one of the mines that was located equally convenient to all of them. A well-planned control laboratory assures production of a uniform, high-quality product. Whenever coal of substandard grade is loaded inadvertently, the sales company can be informed and the proper channel of distribution made. Conversely only constant and strict laboratory supervision can insure proper production of the various grades. Knowing the product, the producer can keep out of many customers' arguments that may be both awkward and expensive. Double checking between customers and mine laboratories have solved many disputes' Some nager insist On buying coal On the analysis basis only, with penalties for substandard coal and premiums for coal above normal quality. A substantial percentage of the coal sold by the Ayrshire group is of this nature. The usual procedure is for the customer to sample and analyze the coal as it is unloaded at the plant, and the mine laboratory samples it as it is loaded at the mine for subsequent analysis by the central laboratory. Only the unloaded moisture is considered, rather than the average of mine and plant moisture, and the buyer sends duplicate samples to the central mine laboratory for this determination. The average of the two analyses determines the price of coal at the mine. In this particular case, the laboratory plays an important part in increasing realization for two reasons: (1) every attempt is made to maintain plant efficiency and product quality as high as possible, (2) check on analyses and sampling by the buyer or seller.

Jan 1, 1951

By Erwin L. Zodrow

A geological model of the modes of formation of magnetite and its distribution in the Smallwood iron-ore mine, Labrador, Newfoundland, is given, based on observation and geological mapping. This is called the conceptual model. If mathematical expressions plus probabilistic uncertainty are used to represent the conceptual model, then this is termed a mathematical model. The purpose of this paper is to test if there exists a correspondence between the conceptual model and two related mathematical models (called factor analysis). Details of the statistical technique are given. The results of factor analyses in relation to the magnetite formations in the Smallwood mine are discussed. Several practical mine applications are presented. The difficulty of maintaining quality control over ore mined from any deposit naturally depends on geological conditions; these are usually imperfectly known to concerned mining geologists. One geological condition that would greatly facilitate ore predictions is if a relationship between the observed ore particle distribution* and its mode of origin could be demonstrated. Such a casual interrelationship is normally sought through the application of well-defined geochemical principles of primary mineralization in given geological environments. However, the application of conventional tools of geological research, including geochemistry, to areas that have undergone repeated periods of geological deformation and metamorphism subsequent to primary mineralization becomes rather difficult. More important, the interpretation of such research results are nearly impossible on an objective basis. Mineral assemblages may have been reworked and changed due to tectonic influences to the extent that the present-day observable mineralogy and ore-particle distribution can effectively obscure the mode of origin of the ore. Quantitative measurements, based on petrological investigation of mineral assemblages, reflect the sum-total of all geological influences. Which of several influences had the most effect on existing ore particle distribution is difficult to assess, for these influences can neither be measured directly nor quantified by petro-logical logical or geochemical means. The present study is concerned with the magnetite distribution and its modes of origin within the Small- wood mine,' located in the southern extension of the Labrador geosyncline; see Fig. 1. This geosyncline is thought to have undergone at least two periods of geo-tonic tectonic deformation, separated in time, since the fer-rugenous rugenous sediments were deposited." Detailed geological observations and mappings (1 in. to 40 ft) have highlighted subtle, distinctive features of the magnetite distribution in the Smallwood mine: (1) The magnetite is generally concentrated in bands or layers within this ore body; these bands alternate with specularite-rich bands and quartz bands. The banded or layered nature is common in Precambrian iron-ore deposits, and this has been interpreted as a result of changes in depositional environments. (2) The grain size of the magnetite varies; near the contacts between the iron and quartz-carbonate formations, the magnetite occurs as well-crystallized octa-hedra. In areas of intense folding, magnetite is extremely fine grained and concentrated in bands and occurs in association with earthy manganese minerals. (3) Magnetite tends to be more highly concentrated near the geological contacts of the iron and quartz-carbonate formation in the northeast part of this mine, Figs. 2, 3, and 4. (4) Magnetite is also fine grained and tends to higher concentration near and parallel to fold axes; however, in this case, the ore is much softer than given in item 2. (5) Magnetite mineralization decreases along strike and away from the areas of intense folding, i.e., towards the approximate center of the mine, Fig. 3. How can these variations of magnetite be explained on a geological basis? We can postulate a conceptual model that the distribution of magnetite appears to be related to three basic geological influences: (1) geo-tectonics, i.e., concentrations of magnetite near geological contacts of the iron and quartz-carbonate formations, the fine-grained nature of magnetite and its higher concentrations near fold axes, and decrease of magnetite towards the approximate center of the mine; (2) secondary alterations, i.e., variation of grain size of magnetite near the iron and quartz-carbonate contacts, and in areas of intense folding where magnetite occurs together with earthy manganese minerals: (3) original

Jan 1, 1971

By J. R. Mihalisin

Phase changes in as-cast alloys in the Ni2 CoCr-Ni, Ti-NSAl system containing 0.1 wt pct C were studied after heat treatment at 1650°F. It was found that a vegion of CrCo-type s was developed in this system after I1000 hr. The tendency for s formation was dePendent upon the aluminum and litanium content, the s -forming tendency generally becoming more pro-nounced as the latter two elements are increased. s lended to form in interdendritic regioues and was associated with solutioning- of- carbide phases. Electron- vacancy computations for prediction of s formation on these alloys mere in sufficient agreement with what was observed experimentally to indicate that the method should be of value in assessing a-forming potential in cast alloys. However, the correlation of electrotz- vacancy numbers may not be as favorable in cast as cormpared to wrought alloys. THE increasing use of high-temperature alloys for longer times at higher temperatures has resulted in a real need for obtaining information on the phase changes taking place in these alloys since these changes often have a direct effect on properties. This paper reports on a study of the phase changes in Ni-Cr-Co-Al-Ti alloys after prolonged heating at 1650°F. The alloys were selected from the pseudo-ternary system Ni2CoCr-Ni3Ti-Ni3Al and this system was chosen because it is the basis of many of the newer cast commercial superalloys. The attempt here was not to define accurately the boundaries of s formation in the NizCoCr-Ni3Ti-Ni3Al system but to delineate the phase transformations taking place upon heating alloys covering a wide range of chemistries in this system. An addition of carbon was made to all alloys to further simulate commercial alloys. It was hoped that the information generated in this manner would be of more direct use to superalloy designers than an equilibrium diagram approach since commercial alloys generally have outlived their usefulness when equilibrium is attained. EXPERIMENTAL PROCEDURE The alloys were vacuum-melted from carbonyl-nickel pellet, vacuum-grade chromium, electrolytic cobalt, high-purity aluminum and titanium, and spec-trographic-grade carbon.

Jan 1, 1968

By B. Habermann

Artificially consolidated sand models, representing one-quarter of a five-spot, have been developed and used to study factors aflecting misciblt. displacrmenr. Sweep efficiency at breakthrough, size of the mixing zone between two miscible liquids and per cent area contacted by drive after breakthrough were determined tor the high mobility ratios encountered in actual resvrvoirs. Quantitative relationships between the degree of viscous fingering and mobility ratio were obtained by measuring the length of the fluid interface. Scaled miscible-slug experiments, supported by field evidence reported in the literature, have shown that when the slug is followed by dry gas the process is less efficient than expected. In addition to low areal sweep efficiencies encountered for high mobility ratio displacements, the effectiveness of a miscible slug is greatly reduced. This is caused by an accelerated growth of the mixing zone between the driving and the displacing fluids. INTRODUCTION Considerable interest in miscible displacement as a secondary recovery process has been shown by the oil industry in recent years. In addition to extensive laboratory investigations, numerous field operations have been initiated so that 39 miscible displacement projects had been reported' in the United States by early 1959. By far the most popular approach in these projects is the use of an LPG slug followed by dry gas. Laboratory tests have indicated that with a small miscible slug, amounting to several per cent of the hydrocarbon pore volume, practically 100 per cent recovery of the oil in place can be achieved and that all of the slug material can be recovered by a subsequellt gas drive. However, these experiments were conducted on small-diameter long cores that can be considered as essentially uni-dimensional reservoirs that do not represent actual field conditions. It soon became apparent that the inherently adverse mobility ratios existing in the reservoir cannot be ignored in any miscible displacement field project. When a less viscous fiuid such as an LPG slug drives a more viscous reservoir oil, fingers develop that reduce the areal sweep efficiency. The slze of the miscible slug to be used is a subject of some controversy. It has been proposed that the size of siug needed be calculated by setting lengths of the mixing zone proportional to the square root of the distance traveled. This proposal is based on experimental evidence' and theoretical considerations"' in which fingering was not a factor. A prerequisite for successful application of the miscible displacement process to field operations is a better understanding of the following factors. L What is the effect of mobility ratio on the rate of deterioration of a miscible slug? 2. How large a slug should be used for given reservoir conditions? 3. What is the sweep efficiency? The purpose of this investigation was to provide some additional laboratory data that should help to answer these questions. More specifically, it was intended to study more quantitatively the effect of viscous fiinger-ing, mobility ratio and slug size on the efficiency of this relatively new secondary recovery process by means of experiments on thin, horizontal, porous medium models.

By Henry S. Rawdon

The structure of wrought iron as usually described by metallographists and workers in metal in general is that of a fairly pure iron. Impurities, if present, are usually considered as being in solid solution in the crystals of the ferrite matrix or as forming part of the ever present "slag streaks." Attention is herein directed to one type of these dissolved impurities; to the detection of such impurities, particularly in low-grade irons, and to their possible influence on the physical properties of the metal. The attention of the Bureau of Standards was first directed to wrought iron of the peculiar and unusual characteristics to be described later, in material which had failed in service and was submitted for test. The examination was extended to other grades of wrought iron, to see whether such features are of common occurrence in this class of material. MICROSTRUCTURE OF WROUGHT IRON Usual Structure The general microstructure of wrought iron is so well known that a detailed description of it here is needless. There is shown in Fig. 2 the structure of a sample of Swedish iron which illustrates well the matrix of ferrite crystals in which are embedded the slag threads so characteristic of the puddling process and the subsequent working of the material. The usual commercial product contains varying amounts of the impurities commonly associated with iron and steel, i,e,, manganese, phosphorus, silicon, and sulphur together with small amounts of carbon. Of these, the larger part of the phosphorus and some of the silicon present are held in solid solution in the ferrite while most of the remaining impurities, other than carbon, exist in the in closures of slag. Aside from the discontinuities introduced by the slag streaks the ferrite matrix has the microstructure and appearance of a pure metal. No definite orientation of the various crystals or grains is apparent; deep etching of the specimens reveals no intracrystalline features (i.e., within the grains) other than those noted in " pure " metals in general (etching pits).

Jan 1, 1918

By Sandip K. Mitra, John E. Dorn

The Basinki-modified Seeger equation for deformation of metals by means of thermally activated intersection of dislocations was used to ascertain the various factors responsible for the strain hardening of poly crystalline aluminum and a series of a solid solutions of magnesium in aluminum. The analyses were based principally on the rate of change of strain rate with stress and the Cottrell-Stokes ratio. From measurements of these quantities on a series of strain-hardened states, the force displacement diagram for intersection, the density of dislocations in the entanglements, and the contributions of the athermal local stress and long-range stress interactions were deduced. Poly crystalline aluminum was observed to have the same force-displacement diagram for intersection as single aluminum crystals, and the corresponding diagram for the magnesium alloys differed in a manner that suggested that small amounts of magnesium may decrease slightly the stacking fault energy of aluminum. Although poly crystalline aluminum had about the same initial density of dislocations as the single crystals, the density of dislocations increased much more rapidly with strain in the polycrystals. This factor and the higher back stresses generated in the poly crystalline aluminum were the major factors responsible for the higher strength of the poly crystalline aluminum, As the magnesium content of the alloys was increased, the initial density of the dislocations also increased. Most of the alloy strengthening arose from this factor; alloying effects due to short-range order strengthening, Suzuki locking, Cottrell pinning, and so forth, were estimated to be quite small. The gveater rate of strain hardening in the alloys was deduced to be due primarily to the greater increase in the density of the dislocations with strain as the magnesium content was increased. It is the purpose of the present investigation to shed additional light on the average plastic behavior of a grain in a polycrystalline aggregate, by analyses, based on dislocation theory, of appropriate experimental test results. These deductions when compared with those from single-crystal data will then serve to illustrate the major items of difference between the plastic behavior of single crystals and the average behavior of a grain in a

Jan 1, 1963

By Zay Jeffries

This paper will include a brief discussion of Prof. Howe's paper on The Supposed Reversal of Inheritance of Ferrite Grain Size from that of Austenite.l The general subject of grain refining in steel and iron will also be treated. The conclusions reached are stated in the following hypotheses which are discussed more in detail below. 1. The ferrite grain size in pure iron, the ferrite and pearlite grain size in hypoeutectoid steel, the pearlite grain size in eutectoid steel and the cementite and pearlite grain size of hypereutectoid steel are not inherited from the grain size of the mother austenite. 2. The only structural feature that is generally inherited from the austenite of hypo- and hypereutectoid steels on cooling through their transformation ranges is the position of the excess ferrite or cementite at the austenite grain boundaries, sometimes causing complete and sometimes incomplete networks which outline the old austenite grain boundaries. Rapid cooling through the transformation range will cause the non-inheritance of this structural (network) feature. 3. The austenite grain boundaries themselves are nearly always effaced in all steels and also in pure iron during the At transformations. 4. The grain-size refining of steel and iron is brought about by the combined effect of non-inheritance of the transformation products on either heating or cooling, i.e., the austenite transformation products do cst inherit their grain size from the austenite on cooling through the transformation range nor does austenite inherit its grain size from the products which form austenite on heating. 5. In general, in both iron and carbon steel the larger the austenite grain size, the larger will be the grain size of the transformation products on cooling. This, of course, assumes all other conditions constant except the austenite grain size. An exception is found to this general rule in very pure iron such as electrolytic iron. In this instance small austenite grains may form very large ferrite grains on cooling through Arg.

Jan 1, 1918

By Zay Jeffries

Each generation accepts the developments of the preceding generations without full appreciation of the difficulties that had to be overcome or of the effect of any given development on society. Today, the production of pig iron is the yardstick with which general industrial health and progress are measured. So natural and logical does this seem to us, that it is difficult to picture conditions prior to the fourteenth century when pig iron was unknown. Not only was pig iron unknown but iron or steel could not be melted and poured into castings; all iron and steel articles were forged from sponge iron. All castings, as well as many worked articles, were made of non-ferrous metals or alloys. In many parts of the world, over long periods of time, not only was the annual exchange value of non-ferrous metals greater than that of iron and steel, but their combined tonnage was greater. At present, the value of the pig iron produced in a year is of the same order of magnitude as that of all non-ferrous metals combined; the tonnage of pig iron is, however, about twenty times that of all non-ferrous metals combined. Owing to lack of records, we will probably never know the relative importance of the various metals at all periods in historic times. A certain conclusion is that the iron and steel industry, since the discovery of pig iron and the cheap methods of converting it into steel, has grown at a much more rapid rate than the non-ferrous metal industries. Notwithstanding their fundamental fitness for man's needs, iron and steel owe their importance in no small degree to the low cost of production. The low cost was a result of increased knowledge of the production appliances and of the metallurgical processes. This increased knowledge is the key to our modern industrial civilization. It will remain for future generations to determine whether there is now going on a gradual change toward greater importance of the non-ferrous metals, as compared to iron and steel. The world's pig iron production in 1920 was slightly more than twice what it was in 1890, whereas the non-ferrous metals production in 1920 was about two and one-half times that in 1890. Every non-ferrous metal industry has shown marked growth during the last thirty years. During this period, the production of cop-

Jan 1, 1924

By W. P. Heineken, A. T. Child

This paper presents the results of a series of experiments made in the metallurgical laboratory of Columbia University, New Pork City. The object of the investigation was to determine, as far as possible, the changes in micro-structure and physical properties caused by short periods of heat-treatment and the longer malleable cast-iron process. It was proposed to do this by means of micro-photographs, heating- and cooling-curves, and tensile tests after the various heat-treatments. I. Micro-Constituents of Iron and Steel. The list of the micro-constituents of iron and steel has grown till now it includes seven different substances, called ferrite, cementite, pearlite,* martensite, austenite, sorbite and troosite. Only the first five of these are mentioned in this paper, to facilitate the understanding of which, the following brief definitions are given: 1. Ferrite (named by Prof. Howe) is, chemically, iron free from carbon. It is the softest of the constituents, and is not colored by etching, except when long-continued. Under the microscope it is easily determined by its regular polygonal etructure; or, if structureless, as in malleable cast-iron, by the ease with which it is scratched. Ferrite appears in mild steel in small amount, in grey cast-iron, and in malleable cast-iron. 2. Cementite (also named by Prof. Howe) is now generally conceded to have the formula Fe3C. It is the hardest of the micro-constituents, having the hardness indicated by 7 of the mineralogical scale; and hence it is always left in relief after

Jan 1, 1901

By Persifor Frazer

The mines which I am about to describe are all situated in the northern part of the States of Nuevo Leon and Coahuila, Mexico, between the twenty-sixth and twenty-seventh degrees of latitude. They might be grouped, orographically, into four classes: 1. Those in the Sierra de la Ygnana chain; 2. Those in the Sierra de Gomez chain; 3. Those in the Cerro Mercado; 4. Those in the Sierra de San Marcos chain. (See large map.) The first two of these may be further arranged in one geographical district, to which the name, "the Villaldatna. district," may be applied, and the last may be ascribed to the geographical district of " Monclova." Geologically described, the country rock, in which four of the six mines occnr, is a limestone, concerning which a few words will be said further on, to wit.: The Arroyo (gulch), the Montanos and the Pinitos (pines), in the Villaldama district, and La Paloma (the dove), or Iron Mine, in the Monclova district. The San Rafael appears to lie in granite, or a heavy-bedded gneiss, presenting most of the characteristics of the latter, though the contact plane of the limestone is not far off. It is certainly worthy of attention that the ore occurs in that portion of the crystalline rock, which is nearest to the limestone, and it has been thought by some observers to be a true contact vein. It is well known that veins of this character are very often distinguished for constancy and richness. Although the undersigned cannot entirely free himself from the impression that this proximity of different formations has had an important influence in the origin of the part of the vein on which this mine is situated; still he was unable to establish it actually at the contact of the limestone and granite, but rather a short distance within the latter. Two openings of the Riojas vein were respectively in limestone and in rotten whitish granite, but this fact, if established (as by the correspondence of the strike line of the vein in direction with that of a line joining the

Jan 1, 1884

By H. C. Howard

Reaction of oxygen and bituminous coal starts as soon as the coal bed is exposed to air and, with some coals, proceeds with significant velocity even at normal temperatures and at normal oxygen partial pressures of one-fifth of an atmosphere. At higher temperatures, the reaction is greatly accelerated and ultimately a condition is reached where the process is very rapid and we then speak of combustion. It is the purpose of the present paper to discuss the reactions of oxygen and coal at temperatures below those of active combustion. It is these low temperature oxidation reactions which are responsible for heating in storage and for marked changes in agglutinating proper-ties. These reactions may also be employed for the preparation of organic acids, which are of direct interest to the chemical industry. For convenience in discussion, the low temperature reactions of oxygen and bituminous coal can be roughly divided into three stages though there is, of course, overlapping. Stage I is a surface oxidation stage, characterized by the addition of oxygen, with the formation of oxygen containing groups some of which have acidic properties. Carbon dioxide, carbon monoxide and water may be formed con-comitantly and are always liberated at higher temperatures, and in cases where the oxidation is prolonged. Superficially, the coal is little affected by this primary stage of oxidation and usually only minor changes in ultimate composition result. There may be definite changes in coking and coking properties, and heat of combustion susceptibility to further oxidation. The presence of acidic groups can be demonstrated by specific reactions. These groups may show cation exchange properties like the mineral zeolites. The formation of oxalic acid has been reported. If the oxidation is continued, a large fraction of the organic material of the coal is converted ultimately into alkali soluble, acid insoluble products, which have been given the name "regenerated humic acids" and which are the characteristic products of Stage 2. These humic acids, in the solid stage, do not differ greatly in appearance from the original coal, but show large differences in chemical composition and chemical and physical properties. Along with the humic acids, carbon dioxide and some of the water soluble types of Stage 3, are also formed. If the oxidation is carried still further, the humic acids may be degraded completely to the simpler, lower molecular weight acids of Stage 3 which are characterized by solubility in acid as well as in alkaline media, and by their orange, yellow or white colors. Additional carbon dioxide is formed in the transformation from Stage 2 to Stage 3 and, for a number of American coals, a maximum yield of the water soluble types of acids is reached when about 50 pct of the carbon of the coal is converted to carbon dioxide. Primary Oxidation The initial step in the reaction of gaseous oxygen on coal, like that on carbon,

Jan 1, 1949