Search Documents

By Edwin Berry

THE consideration of the present value of a mine is of great importance when planning for the operation of a property,, and it is particularly so in the case of mines that have large ore reserves. At various times during the past 15 years, the writer has had occasion to make rather thorough studies of the subject, and has been greatly impressed by certain important points which these studies have brought out, points which, though they may be well known, are often lost track of in the rush to obtain low mining costs and high daily tonnage output. . It is the object of this paper to present briefly, and in a general way, some of these points, and especially those which have to do with the relationship which (1) ore reserves and plant capacity, (2) grade of ore mined, and (3) ore losses in mining, bear to the present value. Present value, sometimes called present worth or actuarial value, means the value today of the future earnings of an enterprise. Great industrial, manu-facturing or railroad enterprises, if properly handled, go on indefinitely and their value is directly dependent on their estimated annual earnings. Mines, or oil properties, on the other hand, have an earning capacity only until the ore or oil is exhausted, and their present value is dependent not only on their annual earnings but also on their life, which is the length of the period over which they can produce at a profit. A mine, or an oil property, is a "wasting asset," while an estab-lished manufacturing business is not, or should not be. In other words, the present value of a mining property. represents a sum of money on which there could be paid from operating profits a determined rate of interest, say 8 per cent., and in addition an amount which, if invested at compound interest as received, would at the end of the life of the mine pay back the present value. In his "Wealth and Income of the American People," Walter Renton Ingalls says: "The fundamental principle of mine valuation is the present worth of an annual dividend accruing during the period of years corresponding to the life of the mine."

Jan 7, 1922

By C. E. Gerity

Near Bunker, Mo., in the New Lead Belt, Ozark Lead Co. operates a 6000 tpd lead-zinc mine. Mined ore is transported to the surface in three mechanized and automated steps. The mine is developed by a rectangular-shaped sublevel haulage drift 15 ft high by 28 ft wide, driven on strike below the ore zones. Ore transfer raises were driven from the sublevel at locations near the shaft, 1500 ft distant, and on subsequent 1000 ft centers. These 6 x 5-ft raises are slashed to obtain maximum storage below dump points. These dump points are located on each mining level and are of steel and concrete construction. Spiral 12 X 24-ft inclines driven from the sub-level provide access to these levels for equipment and mine utilities.

Jan 11, 1972

By A. S. Argon, G. East

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968

By G. Beghi, G. Piatti

THE authors examined the problem of the gradual transformation of Al2O3 from the transition phases normally encountered in SAP (r -x-n)1-3 to the stable a phase. This phenomenon is well-known at temperatures above the melting point of aluminum,3"6 whereas in this paper the transformation was studied at temperatures lower than the melting point of the aluminum matrix.

Jan 1, 1967

By W. H. Bassett

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (1) Depth of deoxidation of copper heated in reducing gas is greater the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this difference in depth of deoxidation is that, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much mire rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900° C.; that is, deoxidation is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide present in the copper. IN 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: FIG. 1.-EFFECT OF TIME AND TEMPERATURE ON DEOXIDATION RATE OF 0.365-IN. COPPER BY ILLUMINATING GAS; COPPER PLUS SILVER, 99.983 PER CENT. Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

Jan 1, 1968

By E. F. Adkins, R. W. Douglas

The variation of the spectral emissivity of osmium and ruthenium with temperature can be expressed by the following relations: DURING a study of the sintering characteristics of osmium and ruthenium, discrepancies in the previously accepted melting points of the metals were noted. The melting temperatures had not been measured at the time of the work, but were estimated in the literature as 2700°C for osmium and 2450°C for ruthenium.' A recent investigation by Baird2 has shown the melting temperatures of osmium and ruthenium are 3000" and 2250° C, respectively. In the present work, osmium bars sintered at temperatures as high as 2900° C showed no evidence of melting, whereas ruthenium showed definite evidence of melting at temperatures as low as 2250°C. In view of the apparent discrepancies, the melting temperatures of both metals were determined. The spectral emissivities of both metals were determined as an aid to studies of the sintering characteristics of these metals. MATERIALS AND PROCEDURES The materials used in these studies were metal powders supplied by Englehard Industries, Inc., through the courtesy of The International Nickel Co. Analytical data from three laboratories, although not in complete agreement as to the purity of the material or the major impurity elements, indicated that the maximum impurity levels were 0.5 and 1.0 wt pct in osmium and ruthenium, respectively. The metal powders were pressed to 1/4 by 1/4 by 6-in. bars at 20Tsi using carbon tetrachloride as a lubricant. The pressed bars were presintered 1 hr at 1200°C after heating 1 hr at 400°C. The presintered densities of the several bars of the metals ranged from 65 to 80 pct of ideal density. Specimens were self-resistance heated in a vacuum sintering bell. Temperatures were measured with an L&N, disappearing filament optical pyrometer. True temperatures were read at the base of an 0.30-in.-diam, 0.150-in. deep hole drilled into the center of a presintered bar. Apparent temperatures were read from the surface of the bar adjacent to the hole. MELTING POINT DETERMINATION The melting temperature of the metals was determined as the temperature at which a slight additional increase in current through the specimen resulted in a reduced temperature at the base of the hole. The apparent reduction in temperature is a result of the liquid metal filling the hole, thus altering the black-body conditions. The melting points of osmium and ruthenium, based on three deter-

Jan 1, 1962

By H. R. Hanley

The characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previosly ously in the literature.' This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors1 previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (I) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calciurn-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent. * Professor of Metsllurgy, Missouri School of Mines. t Professor of Metallurgy and Ore Dressing, Hea.d of Department, Missouri School of Mines. Assistant Professor of Metallurgy, Missouri School of Mines. 1 Among others, see C. G. Fink and Li Chi Pan: Insoluble .Anodes for the Electrol-ysis of Brine [Trans. Amer. Electrochem. Soc., (1926) 49, 83-1341 and other papers by these authors. U. CJ. Taintori, 8. G. Taylor arid H. P. Ehrlinger: Lead Alloys for Anodes in Electrolytic Production of Zinc of High Purity. Truns. A. I. M. E. (1929) 192-200. 2 H. R. Hanley, C. Y. Clayton, D. F. Walsh: Investigation of Anodes for Production of Electrolytic Zinc. Trans. A. I. M. E. (1930) 275

Jan 1, 1931

By P. G. Hallof

Only recently has the term Induced Polarization found its way into geophysical literature. Schlumberger first mentioned the possible use of the induced polarization effect in one of his early papers. Later, induced polarization was the subject of several university theses, such as Seigel's at the University of Toronto and Bliel's at the Michigan School of Technology. In addition, a group at the New Mexico School of Mining and Technobgy has done work on induced polarization. There is very little to be found in print on the subject of induced polarization. Several papers have been presented at meetings, the 1958 AIME and SEG* conventions, for instance, on laboratory measurements of the effect and theoretical considerations useful in the interpretation of field results. This paper is the first attempt to present actual field results which show the usefulness of induced polarization as a prospecting technique. There are several phenomena that can cause polarization when electrical current is passed through the ground. In a paper presented at the 1958 SEG* meetings Professor T. R. Madden of M. I. T. demonstrated that only two of these gave rise to appreciable effects. The first is a result of the membrane and diffusion effects in a sandstone that contains appre- ciable amounts of clay minerals. The unbonded charges associated with the clay mineral forma material that passes positive and negative ions with different mobilities. When current is passed through such a system for some period of time, polarization results. The second phenomenon, which gives rise to very much larger polarization effects, is the one used in the new prospecting technique. These effects are a result of the blocking action or polarization of metallic or electronic conductors in a medium of ionic solution conduction. This electrochemical polarization, called "the over-voltage effect" by electro-chemists, occurs whenever electrical current is passed through a volume of rock which contains metallic minerals such as base metal sulphides. This polarization at metallic interfaces in ionic solutions depends upon the chemical energies necessary to allow the ions to continue the flow of current by giving up or receiving an electron from the metallic surfaces. The energy stored in this reaction isanalogous to that stored when a condenser is charged. If a d. c. current flowing through such a system is interrupted, the polarization can be detected as a small, decaying current that flows after the applied current is discontinued. The decaying potential measured is a result of the current flow caused by charges returning to their equilibrium positions from the positions they assumed under the applied potential field. Because of the polarization, there is an excess of change at each metallic interface. There is an alternate method of measurement of the induced polarization effect. The electrical

Jan 1, 1961

By A. Moskowitz, L. S. Redmerski

The corrosion resistance of stainless steels can be strongly affected by surface treatments. Changes in corrosion resistance can relate to surface composition, integrity and stability of the passive film, and to surface profile (roughness). Operations producing oxidation at the surface, such as annealing, heat treating, and welding, can result in a chromium-rich scale and a chromium-depleted metal surface. In order to restore full corrosion resistance, chemical or mechanical clean-up techniques must remove not only the oxide, but also a very thin layer of metal. Laboratory and field test studies show that these factors are particularly significant in less highly alloyed steels. Annealing stainless in a reducing atmosphere (bright annealing) avoids chromium depletion, but as-bright-annealed material does not display optimum corrosion resistance in certain environments. Electro passiva-tion can be applied to improve pitting resistance without significantly changing bright surface appearance. Potentiometric studies show that electropassivated material also displays significantly greater resistance to breakdown of passivity in acid solutions. The application of special surface finishes for appearance purposes can affect corrosion resistance. Roughness is a key factor. Samples of related appearance but with different surface profiles can show significant differences in corrosion resistance. Thus nonreflec-tive stainless with a relatively smooth surface produced by a special rolling process is much superior to material chemically etched to a similar low reflectivity. THE corrosion resistance of a stainless steel is affected by other factors in addition to its bulk composition and metallurgical structure. These other factors include those relating to the specific chemical and physical condition of the steel's surface. This paper will consider certain aspects of surface condition in relation to corrosion resistance. In particular, studies will be described on the effects of oxidation encountered in heat treating or welding operations, of passivation after bright annealing, and of different surface finishes. EFFECTS DUE TO OXIDATION When stainless steels are exposed to high temperature in an oxidizing environment, as in annealing or welding, the oxides formed are relatively rich in chromium. As a consequence of oxidation, the metallic layer directly beneath the scale may be low in chromium to some very thin but finite depth.1"8 Such a change in chromium content could lower the corrosion resistance at the surface, whether or not the oxide layer is removed. Studies were performed relating to the effect of oxidation and chromium depletion produced during annealing and welding on the corrosion resistance of stainless steels. The nominal compositions of steels used in this study and others are given in Table I. A) Annealing Studies on 17 pet Cr Steels. 1) Effects of Pickling Treatments. Studies were performed to investigate the corrosion resistance of air annealed type 430 stainless as a function of the amount of electrolytic pickling after annealing. The material used in this study had been air annealed and electrolytically pickled in the mill. All scale had been removed, and yet the material showed unusually poor corrosion resistance. Laboratory electrolytic pickling studies were performed to determine whether additional metal removal from the surface would improve corrosion resistance. Electrolytic pickling was performed in a sulfuric acid bath using various conditions of bath acidity, temperature, time, and current density. The samples were then rated for corrosion resistance in a ferric chloride spot test. For this spot test, a solution was prepared by dissolving 10 g of FeCl3 . 6H2O, 5 g of NaCl, and 2.5 ml of concentrated HC1 in 200 ml of water. An area on a specimen was cleaned and a drop of test solution was placed on the prepared area. After 5 min, the drop was rinsed off and the area wiped dry. The spot was then rated between 1 and 5 by visual comparison with standard spots. The numerical rating of the standard spots can be described as follows: 1—No clouding of surface; 2—very slight clouding of surface; 3—slight clouding of surface; 4—moderate clouding of surface; 5—strong clouding of surface. A rating of 1 or 2 was considered to have passed the test, a rating of 4 or 5 represented failure, and a rating of 3 was considered borderline. The severity of etching in this test has been related to the actual chromium content at the surface.4 Etching (clouding) occurs on type 430 stainless (rating of 4 to 5) when the surface chromium content is 14 pct or less. The effects of current density and retention time when electrolytically repickling this material in 6 pct sulfuric acid are shown in Fig. 1. Increasing the cur-rent density or retention time improved corrosion resistance as measured by the spot test. Similarly, increasing acid concentration of the bath or bath tem-perature was found to improve corrosion resistance. The conditions making for improved spot ratings resulted in increased metal removal, regardless of specific pickling conditions used, Fig. 2.

Jan 1, 1970

By Stanislaus Skowronski

OVERPOLED copper, as commonly defined, is copper which has been excessively reduced during the poling period of the refining process. Owing to its porosity, such copper is unfit for commercial purposes. The cause of this phenomenon is undoubtedly the lack of oxides in the copper, yet this does not completely explain it. Refined copper of the same "pitch" and "set" varies considerably in oxygen contents, and analyses of overpoled bars also show similar wide differences; moreover, it is possible to melt copper in crucibles so as to obtain bars that are practically free from oxygen although they show a "tough pitch" and "level set" surface. Frederick Johnson advances the following theory: The regulation of the quantity of oxygen in copper is the keynote of all copper refining. It is the presence of a Well defined proportion of oxygen in the form of cuprous oxide, forming a copper-cuprous oxide eutectic, Which enables copper to be cast free from blowholes. It seems that When oxygen is present, other gases are less soluble in molten copper; When oxygen is absent, or is present in insufficient quantity, the copper dissolves other gases, such as hydrogen and carbon monoxide, Which are insoluble in the copper when solid, and, being rejected during the process of solidification, causes internal porosity and external ridges and excrescences.1 The "level set" of Wire bars, etc., is entirely the result of a compromise between the occluded gases and cuprous oxide. With excess of the former the metal would be "overpitch" and spongy, While an excess of the latter would result in the metal being "underpitch" and brittle.2 The result of the absorption and subsequent expulsion of reducing gases, carbon monoxide and hydrogen, and the effect of this action. on the overpoling of copper are in dispute; the literature on the subject is full of contradictory statements and will continue to be so until better analytical methods have been developed. Sulphur, however, is tangible. The refiner can see it in his button sample and consequently attributes to it any trouble that may happen during the melting of the copper.

Jan 3, 1918

By C. M. Young

THE following paper has been prepared with the object of placing on record in the Transactions some facts concerning the present condition and future prospects of the coal industry of Illinois. In presenting it, the writer wishes to say that a considerable amount of the material contained is taken from the publications and records of the Illinois Coal Mining Investigations, the annual Coal Report of the State Mining Board, and the work of the State Geological Survey. Coal Beds and Mining Methods According to the latest maps of the State Geological Survey, there are only 19 of the 102 counties of the State some portion of whose territory is not within the borders of the coal measures. If outlying areas in Calhoun and Whiteside Counties are considered, the number is reduced to 17. This does not mean that all of the 85 counties that are partly or wholly underlain by coal measures will become producers, as there are some portions of the State in which the coal does not occur in beds of such thickness as to warrant the hope that it can be mined. The mining of coal is widespread, however, for in 1916 there was production from 51 of the 102 counties of the State. There seem to be no cases in which operations will be limited by depth, as none of the coal measures lie at depths much greater than those at which it has been proved that coal may be profitably mined in this field. In fact, the deepest shaft reaching a bed of bituminous coal in the United States is located in this State at Assumption, where coal only 3 ½ ft. (1.07 m.) thick is worked at a depth of 1004 ft.. (306 m.) The coal beds occur in the form of a basin which is deepest along a line extending through the central part of the State and bearing a, little west of north. The northern, western and southern borders of this basin lie within the boundaries of the State, but on the eastern side the Illinois field is continuous with the Indiana field. The glacial drift covers all except the extreme southern end of the State and the visible outcropping

Jan 9, 1917

By Carroll Forbes

INTRODUCTION MANY different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. DESCRIPTION OF BITS TESTED The 4-point bits were the usual shaped bits commonly made on the Leyner sharpener with 14° taper on the wings and a 90° angle between cutting edges. Some tests were run at 85 lb. pressure with a 4-point bit made with a 5° taper on the wings. This was made by using the Carr bit die. The 6-point bits were the usual shaped hits made on, the Leyner sharpener. The Carr bits were made with a 5° taper and an angle of 100° between cutting edges.

Jan 8, 1917

By L. F. Pease, J. H. Brophy

A phase diagram for the Ta-Zr system is presented. The system is of the minimum-melting point type with the 0-zirconium phase decomposing monotectoidally at 785°C and 95.5 at. pct Zr. The minimum solidus temperature is 1875°C and the temperature of the top of the monotectoid loop is 1775°C. Techniques employed included X-ray diffraction and fluorescmce, electron microprobe analyses, diffusion couples, metallography, and melting-point measurements. Errors due to interstitial solutes and in melting observations are particularly common in this system, and their occurrence is discussed. SEVERAL versions of the Ta-Zr phase diagram have been reported in the literature.lm7 Williams et al.' report a diagram of the minimum-melting point type with a monotectoid reaction at 800°C and 12 wt pct Ta. The minimum in the solidus occurs at 1820°C and 25 wt pct Ta, while the top of the monotectoid gap is located at 1780°C and 80 wt pct Ta. The experimental techniques employed were metallography, electrical resistance variation with temperature, dilatometry, X-ray diffraction, and direct observation of melting by the technique of Pirani and ~lterthum.' Experience in the Nb-Zr phase diagram has shown that small changes in the interstitial content can cause large shifts in the positions of the phase boundaries. Small amounts of inter -stitials can cause similar changes in the Ta-Zr system and may be responsible for the wide variations in the phase diagrams previously reported.'-' The authors15 have found that alloys containing 0.75 wt pct 0 and 1.0 wt pct Ni with tantalum contents from 19 to 85 at. pct often contain a lamellar or cellular precipitate after annealing above 1400°C. This precipitate is very similar to that reported by pollack,12 Ralls," and Donlevy17 for the Ni-Zr system. In the present investigation, a wider variety of experimental techniques and improved alloy purity were applied to the resolution of errors in diagrams for this system as they now appear in the literature. New results have been obtained in the areas of alloy homogeneity and purity. Errors in the common techniques of direct melting observation in binary alloys have been demonstrated. In the commercially important high-tantalum region, the more accurate metallographic method of solidus determination has been employed. EXPERIMENTAL PROCEDURE Nominal analyses of the materials employed are given in Table I. The zirconium was low hafnium reactor grade iodide crystal bar, and the tantalum was in the form of high-purity sheet. Powders were impossible to use because of gas content. Alloys were melted on a water-cooled copper hearth, with a thoriated tungsten-tipped nonconsumable electrode in 2/3 atm of Zr "gettered" argon. Alloys were

Jan 1, 1963

By C. G. Wilson

DURING the course of some experiments on the plastic deformation of gallium a standard stereo-graphic projection was prepared with (001) at the center and it was felt that this might be useful to others working with single crystals of gallium. The stereogram, given in Fig. 1, was made using the following crystallographic data (Bradley, 1935):

Jan 1, 1962

Jan 1, 1966

[ ]

Jan 1, 1938

By G. Donald Emigh

WESTERN phosphate resources which lie in Ida- ho, Montana, Utah, and Wyoming, have seen great expansion of activity in recent years. Growth has been two-pronged: expansion in fertilizer use, and since 1949, into the elemental phosphorous industry. Elemental phosphorous, produced in the electric furnace, goes largely into chemical making. Phosphate ore was first recognized in the West about 1889. Production started in 1906, and for many years consisted of underground operations by small companies operating sporadically. In 1920 Anaconda Copper Mining Co. opened the underground Conda mine near Soda Springs in southeastern Idaho, and has maintained and increased its operations since then. About 1930 Montana Phosphate Products Co. began underground mining in Montana and has remained a steady producer. In 1945 San Francisco Chemical Co., one of the oldest companies in the western field, initiated strip mining at the Waterloo mine near Montpelier, Idaho, and later at Leefe mine near Sage Junction, Wyo. In1946 J. R. Simplot Co. began open pit mining at Gay mine near Fort Hall, Idaho. In 1950 Victor Chemical Works began underground development work in the area of Maiden Rock, south of Butte, Mont.: and has since mined there. Monsanto Chemical Co. began open pit mining near Soda Springs, Idaho, in 1951.

Jan 11, 1954

By Cyril Wells, Paul E. Busby, Donald P. Hart

EARLY workers in the field have established that the diffusion of nitrogen follows normal diffusion laws. Concentration-penetration data from layer analyses of reasonably pure iron specimens nitrided in an atmosphere of CO-NH, are given in the literature,' and were utilized to calculate diffusion constants for nitrogen. The diffusion of nitrogen in y-iron may be represented approximately by the equation D - 1.07x10-' e-:".'m'"'r The diflusion coefficients, D, given by this relation represent mean values, since carburization occurred simultaneously with nitriding. The rate of diffusion in a-iron has been determined from calculations based on data obtained by measuring the internal friction of samples at each of several frequencies and temperatures.' The expression for the diffusion of nitrogen in a-iron derived from these experiments is D= 1.4x10-1 e-it tudent Increasing carbon content decreases the diffusion of nitrogen in a-iron.3 Oxygen, either dissolved or combined, has been shown' to exert a marked influence on the diffusion of nitrogen from a nitriding atmosphere. D values increase rapidly with increasing amount of dissolved oxide in the metal, but diffusion is completely inhibited if preliminary oxidation has produced the slightest trace of iron oxide on the surface. Diffusion coefficients have also been calculated from permeability and solubility data,' but these values are of questionable accuracy since the boundary conditions assumed may not actually exist. Experimental Method The method selected for determining the diffusion coefficient of nitrogen in a-iron in the present investigation was the so-called fractional saturation method. This method consists of heating the specimen in an atmosphere of H2-NH8 mixtures of known composition for a predetermined time. Following this treatment, the specimen is analyzed for nitrogen; and the diffusion coefficient is calculated from a known relationship of the fractional saturation, time of diffusion, and dimensions of the specimen. This relation is based on a solution of Fick's second law and assumes that the surface of the specimen immediately reaches a given concentration which remains constant during the diffusion anneal. Tabular solutions are available4-5 and provide the relationship between fractional saturation and the quantity \/Dt /a, where D is the diffusion coefficient in cm2 per sec, t is the time of the diffusion anneal in seconds, and a, in the present experiments, is the half-thickness of the slab specimen in cm. The method is adequately discussed elsewhere.9-10 Material The material for this study consisted of 3/32 in. thick (0.24 cm) carbonyl iron plate. The major impurities in this iron are oxygen and carbon, which are readily removed by long time high temperature treatment in an atmosphere of purified hydrogen. In order to reduce the diffusion anneal time for saturation runs, some of this material was rolled to a thickness of 0.015 in. (0.038 cm) prior to the hydrogen treatment. Hydrogen treatments were carried out in a hydrogen-purified Armco iron tube heated in a global

Jan 1, 1957

By K. G. Gorling, S. J. Wallden, N. B. Lindvall

It is the policy of The Metollurgical Society to provide, in the TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AIME, a prompt and accurate medium for publication of reports of significant new research in both the scientific and engineering aspects of metallurgy. Papers submitted to the Society are judged by competent reviewers according to established criteria for technical merit, accuracy, originality, and presentation. STAFF: Editorial Director, Rixford A. Beals; Associate Editor, James J. Burke; Assistants, L. Capria and R. K. Larkin. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: A. W. Thornton, Choirmon; Dennis Carney, John Chipman, J. C. Fulton, J. H. Hollomon, H. tl. Kellogg, A. E. Lee, R. Maddin, J. D. Sullivan, and O. Swan. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division T. B. King. Cha~rmon; S. J. Dickenson, R. P. Hermsdorf, R. Schuhmann, Jr.. and P. T. Stroup. Institute of Metals Division: Robert Maddin, Chairman. F. Lincoln Vogel, Jr., Vice-chairman, W. A. Backofen, R. W. Balluffi, J. H. Bechtold, M. B. Bever, R. S. Busk, C. G. Goetzel, Paul Gordon, C. D. Graham. Jr., Robert F. Hehe-mann, R. I. Jaffee, F. E. Jaumot, Jr., lrving R. Kramer, A. J. Leno, Horold Margolin, C. J. McHorgue, Russell A. Meussner, J. 6. Newkirk, H. W. Paxton, G. E. Pell~ssier, I. S. Servi, Alan U. Seybolt, A. J. Sholer, and Sack Wahsburn. Iron and Steel Division: J. C. Fulton, Chairman; T. B King, F. C. Langenberg, W. O. Philbrook, and T. B. Winkler. Published bimonthly by the American Institute of Mining Metallurgical and Petroleum Engineers Inc., 29 West 39th Street, New York 18, N. Y. Telephonne pennsylvania 6-9220.Petroleum Subscription Engineers$20 per year for non-AIME members in United States and North South and Central 6-9220.SubscriptionAmerica $25 toreign; $5 for AIME members. Single copies, $4.00, iinalo copies Southfpr;ign,andCentral $5 00. The AIME 'is $25not responsible for any statement made or opinion expressed in its publications Copyright 1958 1958 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . Registered coble address, AIME New York . . . Indexed in Engineering Index, Industrial Arts Index, ...and Chemical Abstracts . . . Application for second class mail privileges IS pending at New Yark, N. Y. Volume 212, Number 2.

Jan 1, 1959