Search Documents

Jan 1, 1951

By William L. Lennemann

Chemistry of uranium with respect to its hydrometallurgical recovery from carnotite ores was investigated and well defined during the radium boom period between 1900 and 1920. Since that time, methods used to extract uranium from its ores have remained basically either acid leaching or sodium carbonate leaching. Until about 1950, the only practical methods known for achieving a better than 75 pct U2O3 concentrate from the leach liquors involved fundamental chemical techniques for either purifying a solution prior to the uranium precipitation, or refining a crude uranium concentrate that was produced by neutralizing a pregnant mill liquor.

Jun 1, 1956

The official Institute reports for the year 1929 were distributed in pamphlet form at the Annual Meeting, February, 1930, and were later included in Section 2 of Mining and Metallurgy, June, 1930, and thus made available to the entire membership. Membership In its report the Admissions Committee set forth the changes in membership during 1929, as follows: Total membership, Jan. 1, 1928, 8582; elected and placed on rolls in 1929, including 59 reinstatements, 509; loss by resignations in 1929, 88; loss by death in 1929, 110; loss by suspension in 1929, 37; membership at end of year not including Student Associates, 8856. Distribution of membership: Honorary Members, 16; Members, 6590; Junior Members, 38; Associates, 1041; Junior Associates, 1033; Rocky Mountain, 138; total membership, Jan. 1, 1930, 8856; Student Associates, 150; total including student associates, 9006. Treasurer's Annual Report, Year of 1929 Statement of Receipts For the year ended December 31, 1929 Dues: Arrears............................................ $ 3,501.75 Current............................................ 97,257.12 New Members...................................... 5,721.50 Advance........................................... 1,970.79 $108,451.16 Initiation Fees.................................................. 7,436.OO Magazine Receipts: Advertising Gross Receipts........................... $40,610.81 Magazine Sales..................................... 3,799.84 44,410.65 Sale of Transactions Current........................... $ 2,985. 15 Sale of Special Editions Current........................ 5,147.82 Sale of Back Transactions and Special Editions........... 4,186.93 Sale of Year Book..................................... 65.50 Sale of Authors' Reprints.............................. 2,585.40 Sale of Pins and Fobs.................................. 14.73 Sale of Technical Publications.......................... 1,451.55 Sale of Bindings...................................... 3,949.13 20,376.21 Net Interest Received: On Bank Balance and Temporary Investments......... $ 2,595.04 On Lie Membership Fund........................... 3,223.43 On James Douglas Library Fund...................... 5,425.61 On General Reserve Fund............................ 2,015.58 13,259.66 Miscellaneous Receipts........................................... 335.80 Total Receipts................................................ $194,269.48

Jan 1, 1930

By Henry Seltz, Cyril Wells, Hugh J. MacDonald

Several investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeserl has made measurements of "average heat capacities" of iron carbide between 1026" and 85" K., using a water calorimeter. His computed true specific heat at 78.1" K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0" K. The cementitc used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes2 has measured the specific heat of iron carbide, from 102" to 323" K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100" K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3 C,S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley3 has reviewed these measurements and calculations, and selects those of Roth* and Naeser6 as worthy of most consideration. Roth has given AH = 5400 cal. + 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (0) he finds AH = 5600 cal. Kelley accepts the rounded figure AH = 5500 as the heat of formation at 298.1" K., but this value is quite uncertain.

Jan 1, 1940

By Henry Seltz, Hugh J. MacDonald, Cyril Wells

Several investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeserl has made measurements of "average heat capacities" of iron carbide between 1026" and 85" K., using a water calorimeter. His computed true specific heat at 78.1" K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0" K. The cementitc used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes2 has measured the specific heat of iron carbide, from 102" to 323" K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100" K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3 C,S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley3 has reviewed these measurements and calculations, and selects those of Roth* and Naeser6 as worthy of most consideration. Roth has given AH = 5400 cal. + 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (0) he finds AH = 5600 cal. Kelley accepts the rounded figure AH = 5500 as the heat of formation at 298.1" K., but this value is quite uncertain.

Jan 1, 1940

By Harry Seltz

SEVERAL investigators have measured the heat capacity of cementite, using different methods of attack, but the agreement between the values obtained cannot be considered good. Naeser1 has made measurements of "average heat capacities" of iron carbide between 1026° and 85° K., using a water calorimeter. His computed true specific heat at 78.1° K. is 11.22 cal. per gram-formula mass, which, if correct, is much too high for any reasonably accurate extrapolation to 0° K. The cementite used by Naeser was obtained from a steel containing 0.9 per cent carbon, by electrolytically dissolving out the iron in a neutral bath of ferrous chloride. The cementite remained as a coarse, crystalline, gray powder. Andes" has measured the specific heat of iron carbide, from 102° to 323° K., as it exists in steel. The specific heats of several slugs of steel of known iron carbide content were determined, and the specific heat of the iron carbide (Fe3C) calculated by plotting specific heat versus percentage of carbon, and extrapolating to pure Fe3C (6.7 per cent C). The heat-capacity values for temperatures below 100° K. were obtained by comparing the temperature-specific heat curve for Fe3C to that of Fe. Since the two were very similar in the range examined experimentally and approach more closely at low temperatures, it was assumed that near the absolute zero the form of the curve for Fe3C would be similar to that of Fe. Andes calculates for the entropy of Fe3C, S298 = 23.55 e.u. The heat of formation of Fe3C has been studied by several workers. Kelley' has reviewed these measurements and calculations, and selects those of Roth4 and Naeser5 as worthy of most consideration. Roth has given ?H = 5400 cal. ± 30 per cent as a result of his own and other work. Naeser has determined the heat of formation from Fe and different forms of carbon, and for graphite (ß) he finds OH = 5600 cal. Kelley accepts the rounded figure ?H = 5500 as the heat of formation at 298.1° K., but this value is quite uncertain.

Jan 1, 1939

The official Institute reports for the year 1929 were distributed in pamphlet form at the Annual Meeting, February, 1930, and were later included in Section 2 of Mining and Metallurgy, June, 1930, and thus made available to the entire membership. Membership In its report the Admissions Committee set forth the changes in membership during 1929, as follows: Total membership, Jan. 1, 1928, 8582; elected and placed on rolls in 1929, including 59 reinstatements, 509; loss by resignations in 1929, 88; loss by death in 1929, 110; loss by suspension in 1929, 37; membership at end of year not including Student Associates, 8856. Distribution of membership: Honorary Members, 16; Members, 6590; Junior Members, 38; Associates, 1041; Junior Associates, 1033; Rocky Mountain, 138; total membership, Jan. 1, 1930, 8856; Student Associates, 150; total including student associates, 9006. Treasurer's Annual Report, Year of 1929 Statement of Receipts For the year ended December 31, 1929 Dues: Arrears............................................ $ 3,501.75 Current............................................ 97,257.12 New Members...................................... 5,721.50 Advance........................................... 1,970.79 $108,451.16 Initiation Fees.................................................. 7,436.00 Magazine Receipts: Advertising Gross Receipts........................... $40,610.81 Magazine Sales..................................... 3,799.84 44,410.65 Sale of Transactions Current........................... $ 2,985. 15 Sale of Special Editions Current........................ 5,147.82 Sale of Back Transactions and Special Editions........... 4,186.93 Sale of Year Book..................................... 65.50 Sale of Authors' Reprints.............................. 2,585.40 Sale of Pins and Fobs.................................. 14.73 Sale of Technical Publications.......................... 1,451.55 Sale of Bindings...................................... 3,949.13 20,376.21 Net Interest Received: On Bank Balance and Temporary Investments......... $ 2,595.04 On Lie Membership Fund........................... 3,223.43 On James Douglas Library Fund...................... 5,425.61 On General Reserve Fund............................ 2,015.58 13,259.66 Miscellaneous Receipts........................................... 335.80 Total Receipts................................................ $194,269.48

Jan 1, 1930

By J. K. Stanley

Knowledge of the diffusivity of carbon in the low temperature form of iron (alpha iron existing below 910°C) is at the moment of considerable interest in the study of the decomposition of austenite and martensite, the elastic after-effect,123 the magnetic after-effect4 and the decarburization of steel below 910°C. Information on the solubility of carbon in iron, and to a lesser extent its diffusion, is also important in consideration of such phenomena as blue-brittleness, temper-brittleness, "magnetic" aging, quench-aging, strain-aging, and possibly the yield point. In order to obtain more information on these subjects more fundamental knowledge is necessary. It is the purpose of this work to present data on the diffusion and solubility of carbon in the alpha iron. The high temperature form of iron (gamma; face-centered cubic) existing above 910°C is capable of dissolving relatively large amounts of carbon, up to 1.7 pet at 1130°C, while the low temperature form (alpha, body-centered cubic) existing below 910° dissolves only a limited maximum amount of less than 0.02 pet carbon at 725°C, according to data obtained here. Since the solubility of carbon in the face-centered or gamma iron is large, relatively speaking, no great analytical difficulties have been encountered in the determination of the solubility lines5 or of the diffusion of carbon.0 The limited solubility of carbon in alpha iron offers difficulties because experimental procedures and analytical methods for low carbon contents below say 0.01 pet have to be more refined than techniques used for work with gamma iron. Because of the difficulties of applying conventional methods to the determination of the diffusion of carbon in alpha iron, virtually no work has been done on this subject. However, by proper refinement of the analytical method for small amounts of carbon, the determination of the diffusion coefficient can be made readily using modified procedures. The solubility of carbon in alpha iron has been determined over a temperature range by various investigators, but the agreement among them is poor. The present investigation establishes the limits quite accurately. Information of this kind is useful in establishing the correctness of equilibrium diagrams but, more significantly, such information on maximum solubilities, especially when extended to alloyed ferrites, should be extremely important in the study of aging and related phenomena. Literature The literature existing on the diffusion, in particular, and on the solubility of carbon in alpha iron is not extensive. The data which exist are not of a high order of accuracy, much of them being in the realm of conjecture. THE DIFFUSION OF CARBON IN ALPHA IRON Whiteley7 made the qualitative ob- servation, using metallographic techniques, that the rate of diffusion of carbon at the A1 (725°C) point was very rapid and that its diffusion was still rapid at 550°C. Snoek,4 studying the magnetic aftereffect in high purity iron, arrived at the conclusion that the after-effect could be explained by the presence of small amounts of carbon diffusing under the influence of magnetostrictive strain (lattice distortion due to magnetic interaction). In later work, Snoek8 made an estimate of the ratio of carbon diffusion in alpha to its diffusion in gamma iron, and concluded that for a temperature of 910°C the ratio of Da/D? was 2600. Polder,9 basing his calculations of D on relaxation phenomena in the elastic after-effect, estimated that Da is about 1/3 of D? at 910°C (1183°K) and is about 1/12 of Dy at 727°C (1000°K). Polder's equation for the diffusion of carbon in alpha iron was calculated to be 18000 D = 5.2 X 10-4 e-RT cm2 per sec Ham10 obtained data for the diffusion and solid solubility of carbon in alpha iron at two temperatures by using one technique similar to that employed in this study. He found a D of 8.0 X 10-7 cm2 per sec at 702°C and of 2.7 X 10-7 at 648°C. THE SOLUBILITY OF CARBON IN ALPHA IRON Although pearlite is absent in steels containing 0.06 pet,11 0.05 pet,12 or 0.045 pet C,13 it appears that the carbon in these steels cannot be in solution in ferrite. The solubility of carbon at the A1 (725°C) point was first determined by Scott14 on the basis of cooling curves, and was found to be between 0.03 and 0.04 pet C. Tamura15 by interpolating between the solubility of carbon in delta iron at 1400°C and in alpha at room temperature (assuming zero solubility) ar-

Jan 1, 1950

By C. N. Reid

Slip-line studies on deformed chromium single cvystals showed the usual bcc behavior. At room temperatuve, cross slip was prevalent—slip was not confined to a given plane, but the slip direction was (111). At -10O0K, slip occuvred on (110) planes, twins on(112) planes, and cleavage on (1001 planes. A single-crystal tensile specimen with an axis close to [011] showed a pronounced yield drop and high strain rate sensitivity which zclere used to derive relevant parame tevs in a dislocation dynamics treatment. Transmission electron microscope studies confirmed the existence of (110) slip planes and showed ecidence of loops punched out by precipitates and of grown-in dislocations promoting tangling. OF recent years experimental studies have been made of the deformation characteristics of single-crystal molybdenum and tungsten, but very little has been published on the behavior of single-crystal chromium. During a study of the mechanical properties of chromium, single-crystal studies were made which have already been partially described.&apos; However, additional information was generated which was not directly relevant to the main theme of Ref. 1, and, therefore, was not reported. In view of the need for complete documentation of deformation modes, the experimental observations made on the deformation of single-crystal chromium are summarized here, together with an electron-microscope study of the associated dislocation structures. It was found that, in terms of the deformation modes, chromium is a conventional bcc metal, showing a very pronounced yield-point phenomenon. Further, it was found that the flow strength of these crystals is very sensitive to the strain rate. Finally, the crystals were observed to contain many unidentified precipitates, which often were associated with prismatic dislocation loops. EXPERIMENTAL METHODS Single crystals were grown from rods of wrought chromium by the method of zone annealing. Rods of "1/4in.-diam were supported vertically in an argon atmosphere while an induction coil was moved up the rod at 1 in. per hr. The power was adjusted to just below that required for melting, and the process produced single crystals in about 30 pct of the rods used. The orientations of the crystals, in general, lay near [011] and are summarized in Fig. 1. Before this treatment, the wrought material contained 35 pprn C, 68 ppm O, and 12 ppm N.* An analyzed single crystal *Usual metallic impurities found in iodide chromium are: Al, 5 ppm; Ca, A ppm; Cu, 2 ppm; Fe, 75 ppm; Yg, 0.5 ppm; Yn, < 3 ppm; Mo, < 3 ppm; Ni, 4 ppm; Si, < 20 ppm; Ti, < 1 ppm; V, 4 ppm; Zr, < 3 ppm. contained 10 pprn C, 79 ppm O, and 50 pprn N. Tension and compression specimens were shaped from the crystals by mechanical grinding, followed by the electrolytic removal of about 0.010 in. from the surface in a perchloric/acetic acid bath. All specimens had a gage length of 0.75 in., and tension specimens had a diameter of 0.100 in., while that of the compression samples was 0.200 in. Mechanical tests were carried out at a rate of 1.3 pct per min, and temperatures below 0°C were attained by means of a nitrogen cryostat similar to that of Wessel.2 EXPERIMENTAL RESULTS Modes of Deformation. In addition to the tensile properties of these crystals, which are described in Ref. 1, deformation markings on the surface were studied. Crystals A and F, Fig. 1, were deformed in tension at 300°K to 10 and 16 pct strain, respectively. The surfaces contained visible slip lines, about 1 C( apart, composed of both straight and wavy segments. They did not define a single plane, and so determination of the slip plane was not possible. However, the slip direction was deduced by comparing the axial orientations of the crystals before and after deformation. Fig. 2 is representative, and shows that the axis ro-

Jan 1, 1968

By G. A. Swanquist, E. M. Morales

INTRODUCTION The idea of water management and control at the Church Rock Mill operations began to take shape in February 1979. At that time, we were already investigating the feasibility of decreasing the fresh water requirements so that the solids would become the limiting factor in tailings impoundment utilization. The area for solution evaporation could be kept at a fraction of the normal requirements under the standard process of full water usage. The Church Rock Mill is an acid leach circuit followed by solids/liquid separation with thickeners in counter current decantation, and solvent extraction. Following the normal design of acid leach circuits, reuse of tailings solution was not incorporated in the original mill process design. INITIAL WATER CONTROL INVESTIGATIONS The investigations to decrease the fresh water requirements centered around modifying the grinding circuit from the present semi-autogenous grinding (SAG) mill in closed circuit with hydrocyclones, to open circuit grinding with a rod mill. The open circuit grinding with the SAG mill and rod mill in series had the potential of decreasing the water requirements for grinding and leach dilution by approximately 50% or 1.4 m3/min (300 gpm). The grinding pulp density would be maintained at 70 to 72% solids, and the leach dilution to 50% solids would be accomplished with acid tailings liquor recycle. In such a grinding circuit arrangement, the SAG mill would provide the primary or coarse grind, and the rod mill would be used for the fine grind. By the SAG mill and rod mill series grinding method of water control and other secondary water controls in various places downstream from the grinding circuit, the required necessary evaporation area was estimated at 120 acres of liquid surface. A second method of water control at grinding was investigated. A two-stage cyclone classification circuit appeared to have a good potential of achieving the same water reduction at a much lower capital and operating cost. However, in retrospect, this would not have been a viable method since a high slime recycle load would have been established hindering classification. The use of reagents to neutralize the acid tailings solution was not considered seriously at that time, since it would have materially increased operating costs, although it would have also allowed more tailings solution recycle and consequently, less fresh water usage. However, with the tailings solution deposition area available at that time, it was not then necessary to incur the high cost of neutralization. The control expected by the series grinding of semiautogenous and rod mills would have been sufficient to maintain a water consumption/evaporation equilibrium well in line with the available land area. IMPLEMENTATION OF NEUTRALIZATION OPERATIONS During the summer of 1979, the UNC Church Rock Mill experienced a tailings dam breach which resulted in a prolonged mill shutdown. Upon resumption of operations at the end of October 1979, tailings deposition was restricted to a small portion of the tailings impoundment area. Figure 1 shows the general tailings area and the limits of the present deposition area in the central part including the borrow pits. These borrow pits had been excavated to provide materials for tailings dam construction. Immediately after resumption of operations, it became evident that it would be necessary to control the quantity of liquid to be evaporated because of the small confined area available for tailings solution deposition and to maximize the deposition time in the tailings area. The water control required had to be exercised on a large scale, and to be in operation as quickly as possible. An obvious solution was to reuse the tailings liquor in mill process. Immediate steps were taken to install the necessary equipment for tailings neutralization on an interim basis. Anhydrous ammonia was selected as the primary neutralization reagent since it was the quickest system that could be placed in operation. Previous laboratory tests indicated fair results with ammonia neutralization. Such a system required a minimum of installed equipment and handling. INITIAL NEUTRALIZATION OPERATIONS Actual neutralization operations began on November 26, 1979. The raffinate solution which normally would have been discarded was pumped to a 3.7 m (12ft) diam by 4.3 m (14ft) tank for reagent contact, see Figure 2. At this tank, anhydrous ammonia was added directly from the tanker trailers and controlled at pH 7.0 nominally. Agitation was provided by air sparging. The neutralized product formed a highly viscous slurry in the grinding circuit which resulted in pumping and cyclone classification problems.

Jan 1, 1982

"Salt Lake City was founded July 24, 1847, by Mormons under the leadership of Brigham Young. It had a population of 118,110, according to the United States census of 1920, and of 151,968, according to a civic survey, January 1, 1925. The Salt Lake metropolitan district is estimated to have 180,079 inhabitants.The city's area is 51.8 square miles. Its altitude is 4,354 feet. It has 514 miles of streets, of which 91 miles are paved. The streets in the main portion of the city are 132 feet wide and the blocks are 660 feet long. It has 144 miles of street railway and 2,200 electric street lights. It has fifteen parks and playgrounds, forty public schools and six private schools. It has eighty-nine church edifices, of which forty-nine are devoted to denominations other than the Mormon Church.It is the capital of the state, the headquarters of the Mormon Church and the headquarters of most of the mining companies and many other business institutions of the state and adjacent territory.The State University, the State School of Mines and the Inter-Mountain Experiment Station of the U. S. Bureau of Mines are in the eastern part of the city. Fort Douglas is east of the University the country clubs are in the southeastern portion of the city. The State Fair Grounds are in the northwestern portion.The city is the center of a trade area about 700 miles in diameter and is in almost the exact center of a circle that embraces the principal western mining areas. It is the home of several widely-known mining supply companies and all the other leading concerns in that line are represented by agency or branch house."

Jan 1, 1925

By L. H. Van Vlack, T. Y. Tien, R. J. Martin

The phase relationships of the MnTe-MnS system were studied by DTA procedures. There is an eutectic at 810°C with about 10 mole pct MnS-90 mole pct MnTe. An eutectoid occurs at about 710°C with approximately 7 mole pct MnS where the MnTe(NaCl) solid solution dissociates on cooling to MnTe(NiAs) and MnS. There is very little solid solubility of MnTe in MnS. ALTHOUGH MnS may exist in three different crystal forms,&apos; only the NaC1-type phase is stable.2 Above 1040°C, MnTe also has the cubic NaC1-type structure. Below that temperature, MnTe changes to the NiAs-type structure.3 This phase transition is rapid for both heating and cooling. As a result the high-temperature crystal form of MnTe cannot be retained at room temperature. Because MnO, MnS, and MnSe are all stable with the NaC1-type structure, and MnTe has this structure at high temperatures,4 solid solution formation could be expected among these compounds. It is interesting to note, however, that a complete series of solid solutions exist only in the MnS-MnSe system,&apos; and that the solid solution is quite limited in the MnO-MnS system.&apos; The MnSe-MnTe system possesses a complete series of solid solutions at high temperatures with separation at lower temperatures.7 Although ion size may be critical in the miscibility of MnO-MnS, it is quite possible that the bond type plays a more important role with the miscibility of MnSe-MnTe. This would permit us to speculate that the miscibility gap would be extensive in the MnTe-MnS system. EXPERIMENTAL Preparation. The samples were prepared by mixing and compacting MnTe and MnS powders. The MnS was previously prepared through the sulfur reduction of Mnso4.8 The MnTe had been prepared by mixing and compacting double vacuum distilled metallic manganese and high-purity tellurium in stoichiometric ratio modified with 1 wt pct excess tellurium. The compacted powders were put in a graphite crucible which was sealed in an evacuated vycor tube. The free space in the vycor tube was made minimal to reduce the loss of tellurium. The sealed assembly was then heated slowly to about 500° C where the free manganese and tellurium reacted vigorously, melting the MnTe which formed. Only one phase, MnTe, was detected by X-ray powder patterns and metallographic techniques. Each compact of MnTe-MnS was placed in a graphite crucible and then sealed in an evacuated vycor tube. The samples were heated at 1250°C for 4 hr and furnace-cooled. Microscopic examination revealed no third phase beyond MnS and MnTe. A typical microstructure is presented in Fig. 1. Identification. X-ray powder patterns were obtained using 114.6 mm Debye-Scherrer camera and Fe-Ka radiation. Mixtures of cubic MnS and hexagonal MnTe were observed in all of the compositions prepared. No lattice parameter change was noticed among different compositions, indicating no solid solution could be retained at room temperatures between these two end-members. A lattice parameter of 5.244Å for MnS was obtained by the Nelson and Riley9 extrapolation method using the diffraction lines of (h2 + k2 + 12) equal 12, 16, 20, and 24. The values, a = 4.145Å and c = 6.708Å, for hexagonal MnTe were obtained from the (006) and (220) lines in the back-reflection region. These values agree well with the values reported by Taylor and Kag1e.10 Differential Thermal Analysis. A differential thermal analysis procedure was used to determine phase relationships since the high-temperature equilibrium conditions could not be retained for examination at room temperature, even when the sealed samples (~0.5 g) were quenched in water. The samples were sealed in an evacuated 4 mm vycor tube with a recess in the bottom to accept a thermocouple. An Al2O3 reference was similarly prepared and the two placed within a piece of insulating fire brick to dampen spurious temperature changes within the furnace. The furnace was controlled by a mechanically driven rheostat which increased the temperature at a rate of about 15°C per min. Known phase changes in the Pb-Sn system1&apos; and the a-to-ß quartz inversion12 were used for calibration

Jan 1, 1969

By Paul J. Fopiano

SOME relationships between the flow characteristics of iron single crystals of 99.9 pct purity and the behavior of imperfections have been investigated. X-ray rocking-curve measurements and etch-pit counts were made as a function of plastic strain, and compared to the stress-strain curve obtained on a modified Polyani tensile machine. Crystals grown from rolled strips of vacuum-melted iron by the strain-anneal method1 had a high preference for a (110) longitudinal direction and a (211) face normal. The tensile specimens were prepared from 2 by i by 0.040 in. single crystals having a gage area of 3 by \ in. Rocking-curve measurements were carried out with a highly perfect germanium monochromating crystal in which the dazz spacing was matched to that of the dZl1 in the ir0n.l Well-collimated CuKal radiation was used throughout. These procedures practically eliminated errors due to geometrical and wavelength resolution. Inasmuch as the rocking-curve half breadth may vary markedly from point to point in the specimen being irradiated, the crystals were strained in place by mounting a hydraulic loading device on the double-crystal spectrometer. The rocking curves were taken after each increment of strain in the unloaded condition, since no observable difference was found in the rocking-curves between the loaded and unloaded states. The rocking-curve half breadths of the as-grown specimens were in the range 90 to 120 sec of arc when the beam irradiated an area of about -£ by -& in. on the specimen. DeMarco and weiss3 have shown that, for a well-colli- mated X-ray beam, irradiating about 10"! sq in. of the very same material, half breadths within 10 pct of the Darwin natural half breadth were observed. Since the rocking-curve specimens were stressed by the load-unload technique, the strain achieved at any given stress depended on the time of holding because of low-temperature creep. Fig. 1 shows the rocking-curve half breadth (also area/peak height) as a function of plastic strain for a relatively short holding time (2 to 5 min) at each stress level. For strains less than 0.1 pct the rocking-curve breadth is essentially constant; it is only for larger strains that there occurs a significant increase in this breadth. Where the holding times at each stress level were longer (by well over an order of magnitude) there occurs a significant increase in the rocking-curve breadth only after plastic strains of the order of 0.6 pct had been introduced into the specimen. This observation is related to the time dependence of creep phenomena and emphasizes the difficulty in comparing data obtained by two such different straining methods. Etch-pit results were obtained using a 2 pct nital etch on specimens strained in the range of 0 to 1 pct. Prior to etching, all specimens were annealed for 3 hr at 150°C, the carbon content being sufficient to decorate the dislocations for strains of at least 1 p~t.~ The data points were all taken from parts of the same single crystal which had been strained with short holding times at stress in increments of strain of the order of tenths of 1 pct. The (211) plane is particularly difficult to etch-pit in vacuum-melted iron and therefore it is felt that these values are as much as an order of magnitude low. Fig. 2 shows the etch-pit density as a function of plastic strain. The smooth curve passing through the data points is not meant to infer a quantitative correlation with the rocking-curve data. What is of interest, however, is the change in etch-pit density in the region of 0.2 pct plastic strain. The first three increments in strain (points 2,3, and 4) did not produce a measurable change in the etch-pit density while subsequent increments did produce a measurable change. While the absolute values of these results do not appear to be cor-

Jan 1, 1967

By Walter Kauenhowen

The crude-oil production of Germany without Austria during 1938 amounted to 3,864,518 bbl., representing an increase of 21.7 per cent over the 3,173,373 bbl. produced in 1937. Adding the Austrian production, the crude-oil production of the new German Reich totaled 4,259,717 bbl. during 1938, representing an increase of 25.3 per cent compared with the respective figures of the previous year. According to published official data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1938 was as shown in Table 1. A semiofficial publication1 states that the program of the crude-oil industry for the second year (1938) of the four-year plan was successfully accomplished. According to the same source, new drilling developments at the following localities were promising: Reitbrook near Hamburg, Heide in Holstein, Eicklingen-Sandlingen near Celle, Steimbke near Nienburg, Worms in the Rhine Valley, Gifhorn near Braunschweig, Mölme near Oberg, and at other places. The drilling activity for oil is illustrated by the figures in Table 2.

Jan 1, 1939

By Walter Kauenhowen

The crude-oil production of Germany without Austria during 1938 amounted to 3,864,518 bbl., representing an increase of 21.7 per cent over the 3,173,373 bbl. produced in 1937. Adding the Austrian production, the crude-oil production of the new German Reich totaled 4,259,717 bbl. during 1938, representing an increase of 25.3 per cent compared with the respective figures of the previous year. According to published official data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1938 was as shown in Table 1. A semiofficial publication1 states that the program of the crude-oil industry for the second year (1938) of the four-year plan was successfully accomplished. According to the same source, new drilling developments at the following localities were promising: Reitbrook near Hamburg, Heide in Holstein, Eicklingen-Sandlingen near Celle, Steimbke near Nienburg, Worms in the Rhine Valley, Gifhorn near Braunschweig, Mölme near Oberg, and at other places. The drilling activity for oil is illustrated by the figures in Table 2.

Jan 1, 1939

By AIME AIME

MINING men in general- are a roving lot but not so Selwyn G. Blaylock. Immediately after graduation from McGill in 1899 he went to the Trail smelter and he is there today though he spent three or four years of his early professional life at other British Columbia mining centers. Either he sensed the great possibilities of the company of which he is now vice-president and general manager, or it sensed his; more probably both. Certainly the association was a happy and fortunate one.

Jan 1, 1937

A. Blainey (Ministry of Supply, Atomic Energy Research Establishment. Hnrtoell. England)—With ref- erence to the published work of Hausner et al. on the powder metallurgy of zirconium, it will be of interest to summarize briefly the results of preliminary work we have carried out on this subject at A.E.R.E., Harwell. For the early experiments we used zirconium

Jan 1, 1953

By Dwight E. Woodbridge

DuriNg April, Max, and June, 1910, I was in charge of an examination of the greater part of the Moa iron-ore area in Oriente Province, Cuba, on the north coast, near the east end of the island. My instructions, on arrival at the properties, were to check former estimates of tonnages and grades, and to re-examine the ore comprised in claims covering 44,727 acres. This work included the running of lines dividing the properties into co-ordinate planes, the boring of many thousand feet of holes spaced at the intersections of these co-ordinates, the taking of samples of the ore penetrated, the analysis of these samples for their various constituent minerals, and the determination of the results as to tonnages, depths, and grades, both for individual properties and for the entire group. Each section of every one of the thousand holes drilled was to be compensated for depth and grade with every other, a series of simple arithmetical calculations of no slight magnitude, the mere mechanical labor of which consumed much time, but finally resulted in giving a complete average of all the essential facts for the entire area of 18,000 hectares, Had it not been for the more than willing, active, and able co-operation of the officers of the Spanish-American Iron Co., from Charles F. Rand, President, and Jennings S. Cox, General .Manager, down to the most humble water-carrier, the work would have consumed far more time than it did. The lands thus systematically explored by me were comprised in the following denouncements: Punta Gorda, Yaminiguey, Baracoa secunda, Sagua, Moa, Yajrumaje, Lirio, and Cabanas, all of which were massed as the Moa group, so called, and cover an area of 13,832 hectares, or 34,179 acres. Some 10,000 acres additional to this was included in neighboring properties, lying between Moa and the east end of the island, the Buena Vista,

Jan 1, 1912

By E. L. Tucker

PREVIOUS investigations of E. L. Tucker and R. E. Head&apos; related in particular to the effect of cyanogen compounds on galena, sphalerite, and pyrite, and their behavior in the presence of such com- pounds. The present contribution deals with the float- ability of the copper minerals and of pyrite. All experiments were performed on minus 200-mesh material, the method of preparation being the same as that described in the previous article. Flotation tests were made in a small mechanically agitated machine of 50-g. capacity designed in this laboratory by Gates and Jacobsen." General Naval Stores pine oil No. 5 and potassium xanthate were used in constant amount in all of the experiments; these agents were selected because of their present wide use in the flotation of copper minerals. Lime additions were varied to secure four &apos;final hydrogen ion concentrations, namely, neutral, 0.0005 per cent CaO, 0.003 per cent CaO, and 0.02 per cent CaO. The variation in lime addition was introduced to include the range of alkalinities employed in actual flotation practice.

Jan 1, 1926

By ROY BERENTZ

MANUFACTURE is the transformation of material by the application of energy and power. The energy of a man exerted throughout a day is equivalent to about one horsepower-hour of mechanical work an amount which can be purchased for less than 2c. It is evident that manual labor is uneconomical if mechanical energy can be applied effectively, or without disproportionate expense. Since manual energy is relatively so costly, economy demands that mechanical power be employed so as to reduce the human effort connected with mining operations to a minimum. Power, like other commodities, is most efficiently produced in large quantities. Mechanical transmission, once prevailing, is being rapidly superseded by electric drive. There are many reasons for this change; such as increased production, ease and accuracy of control, convenient application, ease of moving, etc.

Jan 1, 1930