Search Documents

By Stanley F. French, Bruno F. Koch

Although the amount of dust that will be actually recovered in the six main dust-control systems cannot be accurately stated until the tests mentioned previously are carried out, it is estimated that the average air entering the wet collectors will contain around 5 grains of dust particles per cubic foot. This means that the six systems handling a total of about 133,000 cu.ft. of air per minute will return about 68 1/2 tons of dust to the concentrator per day and since the copper in this dust will average around 2 per cent, the total recovery is approximately 1.37 tons of copper every 24 hours. This important copper recovery is not due entirely to the dust-control system since in a plant without control only the duct that is dispersed to the atmosphere represents a loss. A conservative estimate of the recovery of copper solely due to the dust control system would be about half of the total or approximately 0.70 tons of copper per day.

Jan 1, 1942

By A. G. Jordan, W. Jeitschko, Paul A. Beck

The occurrence qf the V phase structure /Zr,Co,Ge, type) in ternary syste7ns (titanium, zivconium, niobium, lanta1urn) -(nickel, cobalt, iron)-(silicon, germanium) was incestigated. Nine V silicides and four V gertrlanides were found and their lattice constants are reporled. The lattice constants of twenty-one preri-ously identified E phases (TiNiSi type) are given. The average atomic volumes of these phases are discussed in relation to similar binary phases. ThE occurrence of a phase Ti4Ni4Si7 was first reported by Westbrook. DiCerbo, and peat' who gave it the name "V phase". They also reported the existence of an E phase TiNiSi. Subsequently a systematic study was undertaken in this laboratory to explore the occurrence of E' and V phases3 in related ternary systems. In the meantime the crystal structure of the E phase TiNiSi 4 and of the V phase Zr4CO4Ge 75,6 was determined. In the present paper the details of the V phase investigation and the lattice constants of the E and V phases are presented. V PHASES Alloy specimens of approximately 10 to 15 g were prepared by arc melting under argon (99.996 pct Ar) atmosphere. The starting materials were all of purity higher than 99.9 pct, with the exception of cobalt. which contained 0.14 pct Fe as the only major impurity. The weight losses were in all cases less than 2 pct, in most cases less than 1 pct. The samples were encapsulated in fused silica tubes with sufficient argon to yield about 1 atm pressure at the annealing temperature. After the homogenization anneal. Table I. the specimens were water-quenched. A representative portion of each specimen was then examined metallographically (etchant: 20 pct HNO,. 10 pct HF. 25 pct glycerine, 45 pct H20). Only minor amounts of second- and third-phase particles were observed in the specimens listed in Table I, with the exception of alloys Zr4Fe4Si7 and Ta,Fe,Si,. which contained an estimated 10 pct by volume of foreign phases. X-ray powder photographs were taken with a Seeman-Bohlin type focusing camera and Fe-KO radiation. Of the thirty possible combinations of elements in the ternary systems (titanium, zirconium. vanadium. niobium. tantalum)-(iron. cobalt, nickel)-(silicon. germanium) thirteen V phases could be identified. In the remaining seventeen ternary systems and also in the systems Cr-Ni-Si and (M0.W)-(Ni.Co)-Si no V phase was found at the composition 4:4:7 after annealing at temperatures between 900" and 1200'C. For the determination of the lattice constants of the V phases Debye-Scherrer photographs were taken using the asymmetric film arrangement and CrKcr radiation (ka1, = 2.28962A). Using the positional parameters, as determined6 for Zr,Co,Ge,. Table 11. intensity calculations were carried out for each of the V phases with the aid of a computer program.: Thus unequivocal indexing of the diffraction patterns was greatly facilitated. The lattice constants. Table I. were then computed by a least-squares fit of the high-angle lines with f (0) = cos2 Q as extrapolation function. Only few. if any. very weak impurity lines were observed, with the exception of the three iron alloys Zr,Fe,Si7. Zr4Fe,Ge7. and Ta,Fe,Si7. The agreement

Jan 1, 1970

By AIME AIME

A DOCUMENT of progress and of great interest to engineers is the report of the Military Affairs Committee of 'the Engineering Council, which has just been accepted and sent to the secretary of War. It provides .a plan whereby civilian engineers holding commissions in the Reserve Corps may; with their con- sent, be called into service of the army during peace at any time, either with troops in the field or in a consulting capacity on any government engineering work. The Military Affairs Committee finds ample authority in the military bill passed by Congress on June 4, 1920, for this arrangement and also for extending the privilege to military engineer, officer-s of the regular army to engage in civilian work during times of peace. It is hoped that the Secretary of War will adopt the suggestions and put the program outlined into effect. This is a constructive piece of work comparable to the efforts of the military Committee before the war which developed so much in the way of preparedness, particularly in the program of military lectures which, held in the auditorium in the Engineering Societies Building, became so popular that each lecture had

Jan 1, 1920

By H. F. Yancey, O. L. Furse

Although usually coal is screened with punched plate screens having round-hole perforations, there has been an increasing use of wire-cloth screens with square apertures, especially at pneumatic coal-cleaning plants and at other plants that use vibrating screens. It is therefore desirable to establish a relationship between round-hole and square-hole screens for use not only in experimental investigations of coal-preparation problems, but also for use in commercial operations. This need is apparent whenever it is necessary to substitute wire cloth for punched plate and still retain the familiar trade-size product. Although similar work probably has been done by industrial organizations concerned with the screen sizing of coal, the only recorded study of the subject other than the one described herein of which the authors are aware is that of Roesler,1 who screen-sized two samples of limestone and two of zinc concentrates crushed to pass 1/2 in. with a set of square and round-hole screens and found the ratio to be 1:1.23. Procedure In the course of a study of various methods for determining the friability of coal,2 it was necessary to screen-size the products of a series of friability tests of three different coals with both round-hole and square-hole screens. The coals used were from the Roslyn No. 3 and the Bayne mines in Washington and the Rolapp mine in Utah. Twenty 25-lb. samples of each of these three coals at 3 to 2 1/2 in. round-hole size were dropped from a height of 10 ft. to a concrete floor, and then screened with

Jan 1, 1934

By C. G. Goetzel

Until recently porous bronzes have found many applications for self-lubricating bearings in the automotive, electrical, household appliance and general machine industries. The bulk of an annual production of several million pounds of copper powder had gone into the manufacture of these articles, of which by now more than a billion are in service. However, the war has brought severe curtailment of these bearings because of the scarcity of the two main constituents, copper and tin. The development of substitute materials of equal or superior properties has led to a large-scale replacement by products made from iron powder. In spite of the diminished interest in powdered copper-tin alloys caused by this trend, it was believed worth while to investigate some mechanical properties of these materials as a reference base for substitutes. In addition, experiments using the hot-press method were incorporated to investigate possibilities of saving vital equipment or opening new fields of applications. It must be assumed that by this time the powder metallurgy process of making porous bronzes, a development that found its first industrial applications more than 10 years ago, is well known in engineering. The patent literature and bibliography is volu- minous, most publications referring to porous, self-lubricating bronzes, containing about 10 per cent tin and I to 5 per cent graphite, with porosities in the range of 25 to 35 per cent.l-7 The excellent antifriction properties of these bearings, caused by the uniform impregnation with oil, are dependent on the interconnection of the pores and the uniform distribution of the graphite inclusions. The sintering mechanism of porous bronze, with its structural changes during the transformation of the metal powder into the sintered bearing has been shown in colored photomicrographs by Hall.* Diffusion between copper and tin was found to begin within one minute, when tin-rich transitory phases were formed. After 25 min. a homogeneous matrix of alpha was reached for an alloy containing 9.5 per cent tin and 6 per cent graphite. Price, Williams and Garrand,9 studying certain metal powder combinations in which sintering is accompanied by the cementing action of a liquid phase, including a 90-10 bronze sintered at 925°C., have found that if the treatment is carried out within the liquidus and solidus temperature range of the system, a peculiar process of alternate solution and precipitation occurs. The particles of the major solid constituent are dissolved in the minor liquid phase, but thereafter are reprecipi-tated on certain nuclei, which develop into large grains, usually rounded.

Jan 1, 1945

By Donald L. Katz

THE Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July 1, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produces 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand' indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplification and generalizations are necessary to give the over-all picture in so short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, r, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City. Wilcox Secondary Recovery Association on Sept. 5;.1940. Some information is taken from a report to the Association by C. V. Sidwell on March 1, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." HISTORY OF WILCOX ZONE The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. 12.1 .4 and areal map of Fig. 2. The sand is of Ordivician age and is composed of well assorted, rounded' sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 was dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1937 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1941

By K. S. TWITCHEEL

THE different lines leading out from the vocation of a mining engineer are,' perhaps, the most' varied of all the professions. The expedition sent by Charles R. Crane of New York 'as a gift to the Imam Yahia, king of the Yemen, Arabia, was probably unique. Mr. Crane made a visit, in January,1927, to the Imam Yahia at Sanaa, capital of the Yemen. He was received with the utmost cordiality and respect, as his friend- . ship for the ,Arab world is famous; He was 'greatly impressed by the desire of the Imam to develop his country. The Imam stated that he had heard that there were minerals in his country and that he would like to secure engineers to advise him about them and other natural resources.. This seemed such a practical idea, and so greatly appealed to Mr. crane, that he offered to furnish an engineering 'expedition. Naturally the Imam gratefully accepted. This expedition was to study (as far as possible in 'the limited time) the natural resources of the ,Yemen, advise the Imam of what these consisted, and make suggestions regarding the most practical methods for their development. As agriculture is always such a fundamental part of a country's wealth, I first went to Indio, California, to study water-well drilling and the date industry, and eventually arrived at Hodeidah, the principal Yemen seaport, on Oct. 21, 1927.

Jan 1, 1929

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 4, 1915

The Library of the above-named Societies is open from 9, A.M. to 10 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special, attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that, the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library y forwarding copies of mining reports, maps privately issued, and similar material, which will be classified; indexed, and made availableto other members. Suggestions for additions to the Library, either y purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 8, 1914

All the TECHNICAL PUBLICATIONS and CONTRIBUTIONS published in 1940 are available at Institute headquarters, unless otherwise noted. They are also on file in many public, university and technical libraries and, when so indicated in the list, may be found in the TRANSACTIONS. TECHNICAL PUBLICATIONS in Classes A-Metal Mining, B-Milling and Concen-tration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Technical Publications in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. TECHNICAL PUBLICATIONS in Class G-Petroleum Division are distributed in PETRO-LEUM TECHNOLOGY, which was issued quarterly in 1940 but will be issued every other month in 1941. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administration, and L-Geophysical Methods of Exploration are issued as separate pamphlets. An Institute member is entitled to one copy of any TECHNICAL PUBLICATION or CONTRIBUTION. Copies of TECHNICAL PUBLICATIONS listed have been mailed to members of the Institute accord-ing to their registration by classes. CONTRIBUTIONS and other TECHNICAL PUBLICA-TIONS will be sent upon request. A member may purchase an additional copy of a TECHNICAL PUBLICATION or a CONTRIBUTION at one cent a page; minimum charge, 25¢. Nonmembers may purchase any CONTRIBUTION or a TECHNICAL PUBLICATION of the F, J, K, or L classes at the same rate, but the nonmember price per copy for METALS TECHNOLOGY, MINING TECHNOLOGY or PETROLEUM TECHNOLOGY is $1.25 domestic, $1.35 foreign countries. TECHNICAL PUBLICATIONS (separate pamphlet form), $2 per annum domestic, $2.50 foreign. METALS TECHNOLOGY, $7 per annum domestic, $7.80 foreign (Iron and Steel Division and Institute of Metals Division ferrous and nonferrous papers). MINING TECHNOLOGY, $6 per annum domestic, $6.60 foreign (metal mining, milling and concentration, Industrial Minerals Divi-sion, and mining geology papers.) PETROLEUM TECHNOLOGY, $6 per annum domestic, $6.60 foreign. Bound volumes have been mailed to members that have requested them, and MINING and METALLURGY is mailed each month. A member is entitled to one volume a year on his membership and he may purchase for $2.50 one copy of a volume not already received; additional copies of the same volume, $5. Nonmembers may pur-chase the volumes listed, at $5 each, plus 60 cents for Canadian or foreign postage. Extra single copies of MINING AND METALLURGY, 25¢ current issue, back numbers 50¢ each to members; to nonmembers 506 current issue and $1 each, back issues. Subscription price to nonmembers and to members for extra copies, $3 per annum domestic, $4.00 foreign.

Jan 1, 1940

By A. W. Schillinger

Drilling was not entirely satisfactory in the search for native copper in the Osceola amygdaloid footwall, for oreshoots mined were more continuous than drilling indicated. The Geophysics Dept of Michigan Technological University developed a portable induced polarization drill hole probe with a 3-electrode configuration and a sampling radius of 5 ft ±. A 20 ma current of alternately reversed polarity is pulsed at 3.5 sec intervals and readings are taken every 2 ft. Potential is read during the "on" cycle for resistivity determinations. During the "off" cycle, after 10 ms delay, the 1P potential is sampled for 10 ms and recorded. Resistivity (ohm-ft) and "S" values (mv/v) are plotted on semi-log paper. A lithologic log is plotted based on resistivity and anomalous S values noted. The low resistivity amygdaloid contains sills of high resistivity basalt. Verified by core logs, contacts between amygdaloid and basalt could be picked to ± 0.5 ft from resistivity alone. Lithologic logs of long-steel holes, based on resistivity, then replaced sludge logging. An S value of 30 mv/v was established as the lower limit of diagnostic 1P effects in mineralized amygdaloid and 50 mv/v as a threshold value for ore. Of 914 footwall zones drilled, 315 were probed yielding 203 anomalies. Success increased from 34% for drilling to 72% for drilling and probing. As checked by mining, 46 probe results were 78% correct. Failures were due to the instrument not detecting copper or to the misinterpretation of an anomaly. No false anomalies were found. During the past ten years, the Calumet Div. of Calumet &Hecla, Inc has conducted extensive exploration and mining in the footwall of the Osceola amygdaloid lode in the native copper district in Michigan's Upper Peninsula. In an attempt to delineate more clearly the extent and nature of high-grade footwall copper mineralization, 876 diamond drill and long steel holes aggregating slightly more than 47,000 ft have thus far been drilled from the accessible hanging-wall workings in the Osceola No. 6, 13, 14 and 15 shafts. Early in this program it became obvious, through inspection of footwall workings in progress, that due to the erratic and bunchy occurrence of the native copper in the footwall zone, the exploration drilling was failing to outline completely the extent of the oreshoots. Early drilling re-

Jan 1, 1964

By H. W. Maynor, C. J. McHargue

DURING the course of an investigation of materials suitable for use as thermocouples at elevated temperatures by one of the authors, several nlolybdenum-rhenium alloys were prepared. Micrographs of an annealed alloy containing 25 pct Re (intended concentration; analysis not obtained) showed a number of twins, Fig. 1, suggesting a face-centered cubic structure. This note reports the structure and recrystallized wire texture of an alloy containing 25 wt pct Re. Alloys were prepared from 99.9 pct Mo (Fansteel Metallurgical Corp.) and rhenium obtained from the University of Tennessee (purity unreported). Powders were combined and briquetted at 56,000 psi and sintering was carried out at 2400°C for 5 hr in vacuum. Ingots so prepared were swaged at 982.2" to 1037.8oC into wires 0.036 in. diameter, a reduction in diameter of 85.6 pct. These wires were vacuum-annealed 1 hr at 2000°C. A North American Philips 114.59 mm powder camera and nickel-filtered copper radiation were used for structure determination. For the texture determination a Laue-type camera was used with zirconium-filtered molybdenum radiation and, because of the high background, aluminum foil was mounted next to the film. Exposures were taken with the wire perpendicular to the X-ray beam and tilted by 10". It was found that the X-ray pattern could be indexed on the basis of a face-centered cubic structure. Because of difficulties associated with obtaining a good X-ray pattern for this material, accurate parameter determinations were not made. An indicated parameter value of 3.70A was obtained. The X-ray data are given in Table I. The annealed wire texture was observed to be a sharp [111] texture. The spread about this fiber axis was k8" at the surface of the 0.036 in. wire. The annealed wire textures of aluminum have been reported as retention of the [Ill] deformation texture for anneals below 500°C and a new [1121 texture for anneals above 600°C.1 In copper wires, with a [Ill] plus [loo] deformation texture, results indicate a retention of this texture for annealing at lower temperatures and new components or the disappearance of components for annealing at higher temperatures.' The presence of the strong [I111 texture in the molybdenum-rhenium alloy after a 2000 °C anneal suggests that the deformation texture was the same. Acknowledgment The wires used in this study were prepared and heat-treated at the Institute for Atomic Research, and Ames Laboratory, Iowa State College, and the authors wish to express their thanks to the Institute for allowing the use of the material and permission to publish the results.

Jan 1, 1954

By Frances H. Clark

IN wartime, the fabrication and use of metals assumes increased importance, for a modern war of sizable proportions cannot be undertaken with- out a vast supply of this material. Light alloys of aluminum and magnesium, which were comparatively unknown in the last war, will play an important role in this one. Due to research on a vast scale in the interim of years, industry is today well equipped to fabricate metals on an enormous scale. Research for the past year has been most productive and a comprehensive survey in the space of this article would be impossible. It is hoped that the stressing of a few items here and there out of a great quantity of able work will indicate in a small way the advances made within recent times. Specific references to the literature will be omitted at the Editor's re- quest but some authors of papers that I have found of special interest are mentioned.

Jan 1, 1940

By C. F. Frey, P. J. Ahern, J. F. Wallace

THE high affinity of molten titanium for oxygen and nitrogen has resulted in considerable difficulty in developing a satisfactory melting procedure. It has been found necessary to perform melting operations either in a vacuum or inert atmos-phere, and failure to obtain a satisfactory crucible material has necessitated the use of special melting techniques. These techniques have included cold-mold arc-melting utilizing both consumable and nonconsumable electrodes, skull-melting, drip-melting, and levitation melting.' It has been recognized generally that the melting of both titanium sponge and titanium scrap would be expedited by the use of induction-melting procedures but the lack of a crucible capable of containing molten titanium without objectionable contamination thus far has prevented the use of induction-melting procedures. An extensive investigation: which included the common refractory materials was not successful in developing a satisfactory crucible for induction-melting. Some success in induction-melting has been attained with the use of a graphite crucible material, but in all instances sufficient carbon contamination was encountered to cause an appreciable reduction in the optimum mechanical properties of the titanium or titanium alloys. These investigations"" report an increase in the carbon content from approximately 0.3 to 1.0 pct. A serious reduction in the tensile and forming properties has been observed as a result of this carbon contamination. The development of a satisfactory induction-melting procedure for titanium without undue contamination undoubtedly would have considerable economic significance. Such a process would be particularly useful in melting the large quantities of low-cost scrap now available that can only be reprocessed at considerable expense and difficulty by the more elaborate techniques referred to previously. In addition, the process could provide a satisfactory method of melting and alloying of bri-quetted sponge for forging ingots.

Jan 1, 1959

The Institute is one of the five national societies that joined in organizing the Congress, the others being the American Society of Civil Engineers, the American Society of Mechanical Engineers, the American Institute of Electrical Engineers, and the Society of Naval Architects and Marine Engineers. Each society has pledged from its general funds or some special fund a certain sum to guarantee the success of the Congress. To this the engineers resident on the Pacific Coast added $13,000, the total guarantee fund amounting to $37,000. It is hoped that this money, iii part or in whole, can be repaid to the guarantors of the Congress. The sums necessary to conduct the latter and to publish the proceedings, are to be derived from membership fees paid equally by all participating. A member of the Institute as such is not a member of the Congress and will not receive any of the publications of the latter. He is eligible to become a member of the Congress and it is hoped that he will do so. The membership fee is $5, and this entitles one to receive the introductory volume of the Congress containing the proceedings; a digest of the other volumes and a general index. It also entitles the member to one other volume of the transactions, to be chosen as he will. For moderate sums he can buy additional volumes, the whole set costing delivered, $30 or less. On Jan. 12 the total membership was 2,350, of which only 290 were recorded as mining engineers. Full details regarding the Congress have been sent to every member of the Institute, and the failure of the members to take a more active interest in the matter is believed to be due to some misunderstanding of the situation.

Jan 4, 1915

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By F. C. Bond, J. T. Wang

H. J. Kamack (E. I. du Pont de Nemours & Co., Inc., Wilmington, Del.)—Rittinger's law usually is stated to the following effect: "The work (or energy) consumed in particle size reduction is proportional to the new surface area produced." The law has been stated substantially in this way by Taggart20 Berry21 Dalla Valle22 Coghill and DeVaney,23 Richards and Locke," Gross,25 and many others, and, according to Gaudin,26 was originally expressed by Rittinger in the same form. Consequently there can be little doubt that this is the understanding of the law among most workers in the field of particle size reduction. Bond and Wang, however, express the law in the form "the useful work accomplished . . . ." (italics theirs). The distinction is critical, for in the form used by Bond and Wang the law becomes, as they themselves remark "merely a more or less arbitrary definition of useful work," while in its usual sense the law expresses a physical hypothesis which has been verified experimentally within certain limitations. Considering the way the law has been used, it might be stated more explicitly as follows: "In a given machine operating under a given set of constant operating conditions, the work consumed in the particle size reduction of a given material is proportional to the new surface area produced." Or, as Coghill and deVaney have said,27 "the (Rittinger) law holds only when the tests being compared are made under analogous conditions." There are occasions when the law transcends these limitations; for example, the surface area produced per unit energy consumption for a given material in a ball mill does not vary much over a fairly wide range of operating conditions. But by and large, the surface area production per unit energy consumption will vary with the operating conditions, the type of machine, and the material. The essence of Rittinger's law is that the surface area production per unit energy consumption is independent of the particle size, and this has been verified experimentally by numerous workers for numerous materials, within certain limits. An important limitation is that when one grinds to very small particle sizes, agglomerative forces may tend to interfere with size reduction so that the surface area increases less rapidly than Rittinger's law would predict. Within such limitations, Rittinger's law can be regarded as empirically established. The law has, however, certain theoretical implications, and it seems to be chiefly against these that Bond and Wang direct their criticism. Solids are believed to possess surface energy which is proportional to surface area. Thus, Rittinger's law implies a proportionality between surface energy produced and mechanical energy expended (for a particular material in a particular machine). It does not imply that all or most of the mechanical energy is transformed into surface energy; in fact it is known that most of the mechanical energy is transformed into heat. Bond and Wang assert that most of this heat arises from the damping of elastic vibrations of stressed particles. This may possibly be true for crushing (with which they are chiefly concerned), although in grinding it is probable that much of the heat arises from friction between particles. However, the fact that the surface energy is small compared to the heat energy does not invalidate Rittinger's law, which implies merely that they are proportional. The authors also criticize Rittinger's law on the grounds that "this theory cannot be justified mathematically, since work is the product of force times distance, and the distance factor is ignored," and "energy input must be the product of force times distance, and the Rittinger theory completely ignores large variations in the distance (strain dimension or deformation) throughout which a force must act to produce breakage of different materials." However, the quantities force and distance as such are irrelevant to Rittinger's law, which considers energy input as an integral quantity. The fact that different materials require different forces and strains (hence, different amounts of energy) to break them is incontrovertible but again is irrelevant to Rittinger's law, which, as mentioned before, applies -only to a single material. Even in theory, it would not be expected that the surface area produced per unit energy consumption would be the same for different materials, because the surface energy per unit area is presumably specific to each material. Bond and Wang advance another argument of a

Jan 1, 1952

By W. A. Backofen, D. L. Holt

Push-pull fatigue tests have been carried out at 4.2°K, 77oK, and room temperature on two poly crystalline materials of widely different stacking-fault energy (?): pure copper (? - 70 ergs per sq cm) and the Cu-8 wt pct A1 alloy (? - 2.8 ergs per sq cm). Constant stress-amplilude was imposed and measurement was made of the plastic-strain amplitude (ep) at saturation. Lives extended from 104 to 106 cycles. Designating lives at the various temperatures by NRT, N77, and N4.2. the ratios N77/NNT and N4.2/N77 ranged from 3.5 to 18 under the condition of common Ep . Metallo-graphic examination revealed different crack morphology in Cu-8 Al fatigued at room temperature, and at 77" and 4.2oK. At room temperature, cracks lay in or near grain and lain boundavies; at 77o and 4.2oK. cvacks were transcrystalline. Tests on single crystals of Cu-8 A1 showed that such a change in the cracking mode in polycrystallitle material accounted for a factor of- about 3.25 in N77/NRT . The longer life at lower tewperatztre (conslant cp) has heels attributed to two deuelopinents: a reduced production of the dislocation tangles and subgrain boundaries which serve as paths of rapid cracking, and suppression of oxygen chetni-sorption at the crack tip It was concluded that in both materials the luller accounted for an extension of the life at 4.2oK beyond that at room temperature by a factor of 15. XV ECENT experiments on the fatigue of Cu-A1 alloys in the so-called high-cycle range (greater than lo4 cycles) have emphasized the importance of stacking-fault energy (y) as a quantity affecting crack propagation rate and fatigue life.1,2 It was found in comparisons at essentially fixed plastic-strain amplitude that crack growth rate decreased by a factor of about 5 over the composition range from copper (? - 70 ergs per sq cm) to Cu-8 wt pct Al (? - 2.8 ergs per sq cm). The argument was made that, when stacking-fault energy is high, cross slip and climb are favored, so that dislocation tangles and/or subgrain boundaries form more readily under cyclic loading. Since the boundaries and tangles act as paths of rapid crack propagation ,3, 4 life is shortened as a result. However, when stacking-fault energy is reduced (as by alloying), cross slip and climb become more difficult, with the result that substructure formation is retarded and growth rate is also reduced. A purpose of the present work was to investigate the substructure effect in relation to temperature. As temperature is lowered, ? is varied only slightly (if at all), but decreased thermal activation can interfere with cross slip and climb. Thus substructure formation could be curtailed and life increased. Fatigue life in the high-cycle range is also known to be strongly influenced by environment. Working with copper, Wadsworth and Hutchings observed that life in a vacuum of 10-8 mm Hg exceeded life in air by a factor of 20.5 They isolated oxygen as the agent that furthered cracking. While the details are still unclear, a requirement in any mechanism of oxygen-accelerated cracking is that there be chemisorption at the crack tip. That could prevent welding on the compression half cycle,= interfere with reversal of slip,1, 6 or aid in breaking metal-metal bonds at the crack tip.5'7 In the work being reported here, temperature was lowered by immersion in liquid nitrogen and helium, which also served to reduce both the oxygen concentration and chemisorption rate. A possible effect upon life, i.e., a lengthening, had to be recognized. Several researchers have determined fatigue lives at low temperatures presenting their results in the form of stress amplitude (S) vs cycles in life (N) curves.8-11 Such curves reflect, primarily, the fact that metal is strengthened by lowering temperature; effects of substructure and changing environment tend to be masked. The difficulty can be overcome by comparisons based on identical plastic-strain amplitudes, and in the present work the dependence of life on both plastic strain and stress amplitude was established. EXPERIMENTAL Materials. The principal materials were polycrystal-line copper (? - 70 ergs per sq cm)" and the Cu-8 wt pct Al alloy (? - 2.8 ergs per sq cm),I3 the latter being near the limit of solubility of aluminum in copper and having, therefore, the lowest stacking-fault energy in the CU-Al system. Specimens were machined from 0.118-in.-diam cold-swaged rods of high-purity (99.999 pct) copper and the Cu-8 Al alloy, the latter produced initially in a graphite boat by induction vacuum melting a mixture of 99.999 pct Cu and 99.99 pct Al. The machined specimens were annealed to produce mean grain diameters of about 0.070 mm in copper and 0.190 mm in the alloy. Specimen dimensions are given in Fig. 1. Values of the tensile yield stress, ultimate strength, uniform strain (determined by the Considgre construction), and reduction of area, for both materials at 4.2oK, 77oK, and room temperature, are listed in Table I. The tensile apparatus in which these results were obtained has already been described.14 Apparatus. Specimens were fatigued in push-pull with a machine that is illustrated schematically in Fig. 2. The specimen is first soldered into the top grip (1) with Woods metal, and the grip is then screwed into the inner tube (2) which is connected to the drive rod of the Goodmans vibration genera-

Jan 1, 1968

By Fred C. Bond

AN improved method of measuring the surface area of a comminution product down to any desired particle size has been developed. The method is largely graphical, and requires relatively little calculation. It can be used with materials containing large amounts of clay, or excess fines of any kind. The surface area S is expressed in terms of square meters per 100 c.c. of solids. This expression is based upon volume rather than weight, and is considered to be more suitable for crushing and grinding problems, where the machines ordinarily are operated under constant volume conditions. It has the advantage that surface areas of different materials can be compared directly, even though their specific gravities may be unknown. The "specific surface" of a material, or the number of square centimeters of surface area per gram, is equal to 100S divided by the specific gravity. Particle diameters are expressed in microns, K being the diameter of the largest particle present and L the grind limit, or lower size limit of the particles formed directly by grinding. The value of K does not always coincide exactly with the diameters of the largest particles retained on the coarsest testing sieve, since the largest particles formed in crushing and grinding are often slabby, or have other irregular shapes. L has been chosen as 0.700 microns, or number 27.5 in the size number series, for reasons to be explained later. S is the total surface area of all particles larger than L microns in diameter. When a homogeneous comminution product is separated into fractions whose diameters bear a constant geometrical relationship p to each other, and the log per cent weight retained upon each size and passing the next larger size is plotted against the log diameter, a straight line results, which is called the distribution line, and which has a slope in called the distribution modulus. The distribution line can be extended to any desired limiting size, and the total surface area of all particles larger than that size can be calculated. The equation of the distributi0n line is [w = Cx" [I]] where w is the per cent weight retained on each successive sieve; x is the particle diameter; and C is the per cent weight retained on an opening of unit diameter.2 Theoretically, the distribution line can be extended to include infinitely small particles. When it is so extended, and the assumption is made that no fine particles are present other than those accounted for by the equation; the log per cent cumulative weight passing any series of sizes, plotted against the log diameter passed, will result in a straight line lying parallel to and above the plotted distribution line.

Jan 1, 1941