Search Documents

By J. F. Poland

Location of Basins and Geologic Features of Occurrence: The major ground-water resources of California occur and are stored in the many large alluvium-filled valleys of the state. The deposits of Quaternary age which hold the ground water commonly are called valley fill. Meinzerl has discussed the characteristic features of this fill and showed that for western United States its distribution is concentrated chiefly in western Utah, Nevada, central Oregon, California, southern Arizona, and central New Mexico (see fig. 1). For California the principal ground-water basins are shown on fig. 2. Except for the Mojave Desert and the "Basin and Range" Valleys (fig. 2, Nos. 23 and 23A), which are not shown individually, the basins outlined on fig. 2 contain all the large reservoirs in valley fill within the state. The Sacramento and San Joaquin Valleys (fig. 2) together comprise the Great Central Valley of California, which has an area of about 18,000 square miles. The Sacramento Valley contains about 5000 square miles of valley lands, approxi- mately equal to the area of Connecticut; the San Joaquin Valley embraces about 13,000 square miles, equivalent to the areas of Massachusetts and Connecticut combined. Both the area and the ground-water use in the Central Valley is far greater than for all the other shaded alluvial basins of fig. 2 added together. Except for the Sacramento Valley, all the major ground-water basins of the state are south of Sacramento. The valley fill in these ground-water basins has been transported by streams and most of it has been laid down in alluvial fans, producing the typical alluvial-fan structure of aquifers radiating as tongues from a prismatic pile of coarse, permeable debris at the canyon mouths; these aquifers are encased down slope by poorly sorted materials consisting of a clayey matrix with imbedded pebbles and boulders, interbedded with flood-plain silt. In the deeper inland structural valleys, the alluvial deposits interfinger at depth in the valley bottoms with horizontally bedded lacustrine sand, silt, and clay. The San Joaquin Valley is a good example. In the coastal valleys exposed to the sea, such as the Los Angeles coastal plain, the alluvial fans pass coastward into lagoonal and thence to shallow marine deposits. In all these basins, the gravel is coarsest and most permeable near the apexes of the fans, but tongues or lenses of clean gravel and sand may extend for many miles down the fan. Thus, these water-bearing structures are in a position to absorb stream flow near the canyon mouths and to transmit it through the buried radiating conduits.

Jan 1, 1951

By Joseph B. Umpleby

PROGRESS in the petroleum industry in 1929 has been characterized by outstanding accomplishments in the fields of new discovery of supply, economic control of production, increased efficiency and reduced costs of recovery, and lowered costs and greater flexibility in manufacture. Resources have been developed in an outstanding degree in the Kettleman Hills. California, the Oklahoma City field (which adds a large potential area in central Oklahoma), the discovery of Woodbine sand production in East Texas, and the discovery of Wilcox sand production in west-central Kansas. Engineering technique has progressed both along the lines of development and production, with a net result that costs have been reduced and extraction increased in notable degree, although it is impossible to give a close measure of either. In the field of re- fining crude oils variations to the end of promoting reduced cost and greater flexibility has been more important than genera! acceptance of innovations in practice.

Jan 1, 1930

By John Birkinbine

(New Haven 'Meeting, February, 1909.) AWAKENED public interest in efforts to conserve natural resources will certainly be appreciated by the members of the American Institute of Mining Engineers, and a discussion upon conservation may well form a part of one of the Institute meetings, for the records of papers and discussions which appear in the 38 volumes of its Transactions are replete with evidence of effort's in this direction. Every process which reduces the fuel consumed or the power applied per unit of product; every utilization of waste material, or employment of that formerly rejected, to obtain something of value ; every feature of construction or operation which lessens the labor required or increases the output per employee, is an advance in the direction of true conservation. This may not appear from the records of late conferences or from published articles, in which the effort seems to be concentrated upon reducing the consumption and presenting to the people of the country estimates of exhaustion of natural resources. I rejoice in the awakening of public interest in a matter so important for the present and future welfare of our nation; I appreciate the possibility of much good following conferences of the Governors and delegates from various States and from national societies; and I recognize the interdependence, not only of different States, but of contiguous nations. In fact, the marvelous development of transportation by land and by water, and the decreasing rates at which commodities can be moved great distances, have in many cases practically obliterated geographical boundaries, and nearly every country on the globe can either market its product in other lands or draw upon them for raw or manufactured materials ; hence, conservation is an international subject.

Apr 1, 1909

By Wayne A. Greenwalt

A method that determines venture participation when the decision maker's level of risk aversion varies according to venture profitability and risk investment is presented. The decision maker's fundamental aversion to risk is established by the selection of a desired working interest for a venture that anticipates only a discounted payout.

Jan 1, 1982

By H. R. Banks

THE Sullivan concentrator has completed 20 years of operation. During this period a considerable amount of data has been accumulated concerning the characteristics of several types of flotation machines in their application to the problem of the differential separation of the lead sulphide, zinc sulphide and, in more recent times, iron sulphide, in the ore from the Sullivan mine. It is the author's intention to sketch briefly experiences encountered when the several types of flotation machines were introduced into the flow. ORIGINAL FLOTATION EQUIPMENT AND ORE The original flotation equipment consisted of four 18-cell lead-roughing machines, whose concentrate was cleaned in an 8-cell and recleaned in a similar 8-cell machine. Zinc concentration was carried out in four 18-cell machines. One 8-cell zinc re-treatment machine received the reground zinc middling. The 168 cells handled some 3000 tons of original daily feed. These cells were of the standard Minerals Separation type, equipped with 24-in. impellers. Spindles were driven through geared line shaft at a speed of 255 r.p.m. The impellers were the 45° type, except for the last three cells of the zinc-rougher machines, which were of sub-aeration type, with full bottom shroud and half shroud for the top side of the impellers. Four-pound air was introduced. This recognition of the benefit of intensified flotation operation for "gleaning" was an important phase in the early operation and will be discussed further on in this paper. Sullivan ore during this period is described as a finely disseminated mixture of four sulphides, totaling 90 per cent made up of 13.6 per cent galena, 14.4 per cent marmatite, 1 per cent pyrite and 61 per cent pyrrhotite. The specific gravity of the ore was approximately 4.4. There has been a gradual change in the ore content. The 10 per cent of nonsulphide constituents has increased to between 15 and 20 per cent and all three sulphides have dropped somewhat. Added equipment and changing technique have made possible the treatment of 8000 tons per day of mill feed instead of the 3000 originally handled. SPECIAL FEATURES OF FLOTATION AT SULLIVAN Sullivan flotation differs greatly from customary practice. The very heavy return of lead rougher middling and lead cleaner tailing, totaling at times 125 per cent of the new feed tonnage, has been the subject of much investigation. The practice is still employed.

Jan 1, 1944

By M. L. Brashears

IN the last 15 years industrial use of ground water has more than doubled, and in 1951 amounted to 5 billion gallons per day. A similar sharp increase in the utilization of ground water for irrigation and public-water supply occurred in the same period. In many areas rapid increase in withdrawal from wells has taken place almost entirely unhampered by regulatory control and with little or no integration of effort. As might be expected, the chief interest in many regions has been maximum production rather than sustained perennial yield. As a result, widespread depletion of underground reservoirs and deterioration of the quality of the water stored in them has taken place in many areas, even though total pumpage in the United States is far below ultimate potential. Of even more concern is the fact that excessive withdrawal has drawn salt water into the reservoirs beneath many heavily populated centers along the Atlantic, Gulf, and Pacific coasts, causing costly abandonment of pumping plants.' Many hydrologists expect that consumption of water will rise rapidly in the near future, and some predict that industrial requirements will more than double in the next decade.2,3 Thus it appears likely that the draft on many already heavily pumped underground reservoirs will be greatly increased and the search for additional sources of usable ground water intensified in years to come. In view of this, industry as a whole will be forced more and more to recognize the potentialities and limitations of ground-water reservoirs and to utilize them more effectively to prevent costly water shortages and disruption of production. Through painful experience, some industries are already well aware of the need for effective water utilization, and have managed individually or through joint effort to check trends threatening to deplete underground reservoirs completely or to impair the quality of the water. Various remedial measures have been used to bring about successful management of local or regional ground-water resources. Of these, replen-ishment of aquifers by recharge wells or basins has played an important role in overcoming some ground water problems. Artificial recharge of underground reservoirs by water spreading has been practiced successfully in the United States for many years. In the West it has become an important method of salvaging flood run-off for irrigation of crops and maintenance of public water-supply reserves, and it is used to some extent in parts of the East. Artificial recharge by means of wells, on the other hand, is a relatively new development. Until recently it was employed in only a few areas, principally along the East coast. For the last few years, in the ever increasing search for additional water supplies, industry has had greater recourse to this method. Utilization of recharge wells to control the temperature and quality of underground water supplies is also being considered seriously. Operation of recharge wells, like water spreading, is governed largely by local conditions. It requires water relatively low in turbidity, whereas in some areas water spreading has been used successfully with water of high turbidity and silt content. However, water spreading must be employed in large areas and can be carried on effectively only where aquifers crop out at the surface. Recharge wells can be used in limited space. Recharge wells are similar to production wells except that the water flows in the opposite direction. Thus any water-bearing bed that will yield water to wells may be recharged by wells. Often, however, the water available for recharge is of a different character and temperature from that existing in the ground-water reservoir and if transmitted directly underground from a recharge well to a production well might require expensive or difficult treatment before it could be used. Fortunately the physical characteristics of reservoir beds, which control the movement and behavior of ground water, are generally not homogeneous. Moreover, the movement of ground water is very slow because of the frictional resistance of the reservoir beds. By taking full advantage of hydrologic and geologic conditions, it is therefore possible in many instances to bring about favorable changes of temperature and dilution as the water moves from the recharge wells underground to the production wells. Furthermore, if the natural quality or temperature of ground water is unfavorable for industrial purposes, recharge wells may be used to introduce water of more favorable quality or temperature into the ground-water reservoir. When water is discharged into a recharge well, the head in the well is increased. Because of this, a cone of elevation is produced on the water table or the artesian pressure surface in the area surrounding the well. The cone of elevation is similar to the cone of depression produced around a pumping well except that the apex of the cone is above the water table or artesian pressure surface. Thus if a recharge well and a production well tapping the same water-bearing bed are close together, as would be the case at many industrial plants, some of the water discharged from the recharge well would be drawn into the production well within a short time. Under such conditions it is apparent that water of unfavorable temperature and chemical characteristics should not be used for recharging. The more important ground-water reservoirs in the United States often consist of alternating layers of impermeable beds and porous material that will yield water readily to wells. Physical characteristics of individual beds in a ground-water reservoir may not persist over great distances, the impermeable layers grading into beds that will yield large quantities of water. Thus the water-yielding material in underground reservoirs, whether large or small,

Jan 1, 1954

By Evan Just

DIRECT subsidies for mine production in this country began as an outgrowth of wartime 'price regulation. The price-fixing authorities realized that the volume of production to be required from domestic copper, lead, and zinc mines would invoke costs of production considerably higher than the established ceiling prices. Accordingly, beginning Feb. 1, 1942 the Premium Price Plan was set up, which undertook to pay premiums to mines for production in excess of quota, of 5¢ per lb of copper and 2Y4¢ per lb of zinc or lead. Quotas, except for small mines, were initially established at the average rate of production in 1941, but were later reduced arbitrarily on an individual basis. Subsequently, additional "B" premiums were set for lead and zinc of 2Y40 per lb and a further "C" zinc premium of 2%¢. Additional copper premiums were negotiated on an individual basis, mainly with small mines. Quotas under each of these successive categories were the production obtained at the next lower premium level. In other words, under ceiling prices of 12¢ for copper, 6,14¢ for lead, and 83¢ for zinc, it was possible for high-cost operations to receive prices plus premiums of 17¢ or more for copper, 12¢ for lead, and 16% 0 for zinc on a portion of their production. On the other hand, some of the larger operators received only slight premiums and in at least one instance none at all. The average price plus premium for copper was 12.25¢ in 1942 and rose to 13.65¢ in 1945. That for lead was 6.99¢ in 1942 and 8.73¢ in 1945, and for zinc it was 9.06¢ in 1942 and 11.200 in 1945.

Jan 1, 1948

Jan 1, 1937

By J. R. Martson

The arrangement of the larger furnace at the United Verde smelter, together with the boiler layout and connecting flues, is shown in Fig. 1. The important dimensions are given in the figure, and cross-sectional areas of combustion space, flues, etc., are recorded. The location and extent of the baffling in the boilers also are shown because of their importance in the interpretation of the data. Two boilers serve each reverberatory furnace. They are of the class M-26 Stirling type (rated at 713 boiler hp. each). Steam is generated at 178-lb. gage pressure at a total temperature of 528" F., from feed water at a temperature of 113" F. The feed water is condensate from turbogenerators plus make-up softened by the lime-soda process. The make-up is rather large in amount as it must match the amount of steam consumed in reciprocating blowing engines and the like, which are not served by surface condensers. As a result the boiler feed water has a hardness of 1.5 to 3.0 grains per gallon, but this results in the formation, during six months to one year of boiler operation, of scale only of "eggshell " thickness or less. The boilers are set at the same elevation as the tapping floor of the furnace, which results in the introduction of the waste-heat gases at the top of the front bank of tubes and necessitates the inversion of the usual baffling arrangements. The boilers are equipped with valve-in-the-head soot blowers, which keep most of the dust blown off the surface of the tubes, but it is necessary to supplement the soot blowers by high-pressure air lances, inserted by an attendant through side doors in the boiler setting. Deposits of coal ash and of dust from the furnace charge accumulate in the flues between the reverberatory furnaces and the boilers and this necessitates cleaning of these connecting flues by hand during the greater part of one of the three 8-hr. shifts during each 24 hr. This cleaning operation requires the opening of clean-out doors, which, of course, has some effect on the yield of steam. Revebberatory Furnace Practice The United Verde furnaces are fired with pulverized coal of sub-bituminous type of which the screen and chemical analyses are given in Table 1.

Jan 1, 1934

By Frank C. Kelton

A method is outlined for the analysis of large cores, developed primarily for the purpose of obtaining reliable data on fractured or vugular limestones. Porosity and fluid saturations are determined by a modified Dean-Stark extraction after initially bringing the samples to 100 per cent liquid saturation by a vacuum-pressure method. Horizontal permeabilities on the whole samples are determined in two directions, parallel and perpendicular to the di-rection of principal fracturing. Results are presented for various types of formations. A comparison is made between data obtained by this special method and the method of conventional analysis, and discussion is given of the relative advantages and limitations of each. In view of this comparison a modified method for the analysis of fractured and vugular formations is proposed, which method retains the advantages of the previously outlined techniques but gives promise of speeding up the analysis. INTRODUCTION For many years the greater part of the production in the Permian Basin was from formations of Permian and Pennsylvanian age. While production from these formations is still the predominant production. deeper prospecting has brought to light older formations with oil productive characteristics. Attempts to core these deeper horizons were at first usually characterized by poor recovery. The old rule of thumb, "good core recovery — poor well" was originated and remained in effect until recently. With the advent of diamond coring and the increased efficiency in drilling and coring operations. the old adage has lost its significance. Formations of Devonian. Silurian and Ordo-vician ages were successfully cored with varying degrees of recovery. The cores thus obtained were surprising and in some case; disappointing. Good recovery from these formations led to speculation as to the feasibility of analysis and the meaning of data obtained from conventional analysis. Commercial laboratories were engaged to analyze these cores. and their results indicated that data obtained by conventional methods would be of little value. From visual inspection it was apparent that in many cases the effective porosity for storage of hydrocarbons. and permeability. were contained largely in fractures and solution cavities rather than in the primary crystalline structure of the formation. In other cases the solution cavities augmented the effective porosity of the primary crystalline structure, or fractures enhanced the permeabiilty of the latter so that the formation might respond favorably to acidization and become commercially productive. Since the spacing of the cavities and fractures was often comparable to the core diameter, it was evident that the entire core should he analyzed instead of small fragments. On the basis of these observations, commercial laboratories were requested to devise a system of analysis which would yield data of practical value. Pro- cedures have accordingly been developed which seem to meet this requirement, and to date nearly 12,000 large core samples have been analyzed. It is the purpose of this paper to describe the methods used, to present typical results for several fractured formations and to compare the data obtained by this special analysis with that obtained by conventional analysis. Certain modifications and alternative procedures are finally suggested to speed up the analysis. CORE ANALYSIS PROCEDURE Fluid Saturations and Porosity The core sample, in segments up to 15 in. in length. is marked, weighed and examined under ultra-violet light to determine the presence of oil saturation. If present, the approximate quantity of oil and its location on intercrystalline, fracture or vugular surfaces is noted. This information is carefully recorded. The degree of fracturing and/or vugular development is also noted. The sample is then placed in a pressure cell and the air evacuated with a high speed vacuum pump. This evacuation is continued only long enough to reduce the pressure to approximately the vapor pressure of water in order not to remove excessive amounts of water. Water is admitted to the cell and allowed to penetrate the sample under atmospheric pressure, filling the pore space initially occupied by air and replacing the small amount of water removed by evacuation. Pressure up to 200 psi is applied to force water into the smaller capillaries, and the sample is left sub-

Jan 1, 1950

By H. W. Mead, C. E. Birchenall

The rates of growth of graphite nodules in cast irons are calculated for a model of a growing graphite sphere surrounded by a shell of austenite through which carbon and iron are diffusing. The carbon is supplied by a cementite-austenite mixture at the outer edge of the shell. The calculated rates from carbon diffusion agree fairly well with the measured values, but the rates based on iron self-diffusion are much too low. Because the iron must be removed for the process to continue, o plastic deformation mechanism is suggested. THERE has been an unfortunate tendency in the literature of growth and dissolution reactions to identify the slope of a plot of the logarithm of the growth or dissolution rate vs reciprocal of temperature with the activation energies determined by diffusion measurements in chemically similar systems. If the solubility limits at the growing or dissolving phase interfaces change appreciably with temperature, such procedures may lead to serious errors in specifying the mechanisms controlling the rates of these processes. A reaction involving the simultaneous growth of graphite from and dissolution of cementite in austenite will be discussed here to show that substantial oversimplifications have been made in earlier studies of this process. From a dilatometric study of the overall y-range graphitization process, Bunin and Danil'chenko' found an apparent activation energy of 90 kcal per g-atom. They concluded that, since this value was much nearer the approximately 68 kcal per g-atom observed for self-diffusion in pure iron than it was to 32 kcal per g-atom for diffusion of carbon in iron, the rate-controlling process must be the diffusion of iron away from the growth interface to provide space for graphite to grow. Bunin and Salli' bolstered this agreement with the observation that graphite forms preferentially at surfaces, cracks, and pores where free volume is present initially. Ziegler, Meinhart, and DeaconQ ad found an apparent activation energy for graphitization of 98 kcal per g-atom. This value, like that of Bunin and Danil'chenko, applies to nucleation and growth occurring simultaneously. It is not generally assumed that nucleation is entirely diffusion-controlled. Treatments such as prior cold-working and prequenching, which strongly affect the rate of graphitization, would be expected to have little effect on diffusion processes occurring at the graphitization temperature. In any case 90 kcal per g-atom is not particularly close to the 54 kcal or lower to be expected for diffusion of iron which is carbon-saturated.' The presence of silicon in iron is said to reduce the activation energy for diffusion,' so its presence in cast irons would be expected to have a similar effect. The growth rates of nearly spherical graphite nodules have been studied by Brown and Hawkes." The initial rate of growth before impingement of adjacent carbon-depleted areas was found to be parabolic, and rate constants were measured at several temperatures. Their apparent activation energy for the growth process only was roughly 45 kcal per mol. Burke and Owen' made growth-rate measurements on several alloys, recording appreciable induction periods, initial nucleation rates, and average radial growth rates based on an assumed linear rate of radial growth. They found that increased silicon content increases the ovel-all reaction rate and the initial rate of nucleation, and decreases the induction period. Assuming 1) spherical nodules. 2) constant volume rate of nucleation, 3) austenite in equilibrium with cementite at positions where the cementite is not depleted, and 4) a constant diffusion distance during the growth of a nodule, they calculated an apparent overall activation energy of 68 kcal per mol, which was related to an activation energy for nucleation of 79 kcal per mol and activation energy

Jan 1, 1957

By K. V. Lindell

THE 70-mile serpentine belt of eastern Quebec, producing 70 pct of the world's chrysotile, has 11 operating mines, two of which are underground, eight are open-pit, and one is both open-pit and underground. The combined operation, the Jeffrey mine, of the Canadian Johns-Manville Co., Ltd. is the largest producer in the group. Haulage All four of the separate operations falling under transportation at the Johns-Manville Jeffery Mine at Asbestos, P. Q., is handled by the company owned Asbestos and Danville Railway. A variety of equipment is operated over the 25 miles standard gage railway. Included in the scope of transportation are: 1-Hauling mill rock to the mill. 2-Hauling stripping and waste rock to the waste dump. 3-Hauling mill tailings to the tailings dump. 4-Hauling supplies from, and finished products to Danville. Main line tracks are permanent, but those within the pit and on the dumps have to be relocated constantly to follow the mining face and dump edges. Tracks within rock areas in the mine are laid on steel ties and can be moved by a bulldozer. Standard mechanical track shifters move tracks in dirt areas in the mine and on the dumps. Train-movements, both within the mine and over the out-lying tracks are controlled by a dispatcher located at the southwest rim of the pit. Steam locomotives haul all stripping, waste rock, and ore from the mine to the gathering yard at the northwest rim of the pit. Normally, two trains per operating shovel are used, with adjustment for optimum loading. In the event of shovel loading on the bottom level or in good stripping, service may be increased to three or four trains per shovel. From the gathering yard a 100 ton diesel-electric locomotive hauls the mill rock to the mill slips, a distance of about three miles. Electric or steam locomotives haul the waste rock and stripping to the waste dump located about two and one-half miles from the mine. Stripping cars are sprayed with a chloride solution and "gravelled" to prevent wet stripping from freezing in the cars during the cold months. Cars pass under a shaking screen which distributes an even

Jan 1, 1952

By AIME AIME

A PAPER recently presented before the Anthracite Section of the A. I. M. E. by S. J. Phil- lips, Mine Inspector, Fifth Anthracite District, Department of Mines of Pennsylvania, covering the water hazards in the anthracite coal mines of the Lackawanna River Valley, was especially timely because the conditions there are duplicated to a large extent in the Wyoming Valley, which is traversed by the Susquehanna River with its many large tributary streams. Also, in the southern anthracite field, where there are a number of large creeks, similar pumping problems and mine water hazards will in time be presented if mining is continued to its conclusion.

Jan 1, 1936

By W. J. Parton

THE efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/3 2 by 1/3 2 in.) and No. 5 Buckwheat (1/3 2 in. by 0), present a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than s, 32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes.

Jan 1, 1949

By J. T. Ryan

IN making a comparison of mine inspection methods in Europe and the United States, it is necessary to have some basis to start from, which makes this subject rather difficult, as such methods are governed largely by the authority given the inspector by the mining laws. In the United States there are 31 coal producing states and territories and 32 different mining laws under which inspectors operate, as one state-Pennsylvania-has both a bituminous and an anthracite code. Some of these codes are distinctly coal mining codes; others are essentially coal mining but apply also to other mines; several codes are sub-divided referring partly to coal mines and partly to other mines, and a few codes are mainly metal mining but apply in part to coal mining. Having all these different codes in the United States and the departments organized in a variety of different ways, there is of necessity a great difference in inspection methods in this country.

Jan 1, 1926

By R. M. Brick, M. A. Williamson

CERTAIN features of the response of copper and brass to deformation and recrystallization remain obscure. The textures obtained on rolled sheet are listed by Schmid and Boas1 as: No adequate explanation has been advanced for the presence of the secondary deformation texture of copper and its absence in brass or for the origin of the cubic recrystallization texture of copper.2 A recent publication3 attempted to rationalize the above empirically described annealing texture of brass on the basis of retention of the (110) [112] rolling orientation plus twinning about the central octahedral poles of the usual secondary (110) [115] orientation. The difference in the textures of annealed copper as compared to 70-30 brass is also shown by the difference in the position of ears for drawn copper, at o° and 90°, as compared with drawn brasses, at 45°, for all compositions between 90-10 and 70-30.4 Data on individual crystals are as yet too few to permit of an analysis of these textures comparable to that of mild steel as made by Barrett and Levenson.5 EXPERITMENTAL METHODS The materials studied included copper specimens cut from the central, equiaxed crystal portion of a tough-pitch wirebar; brass made from this copper and high-purity (99.99 per cent) zinc including alloys of 7 per. cent, 15 per cent, 24 per cent, 29 per cent and 36 per cent Zn and large single crystals of 70-30 brass. Sections ¼ in. thick of the cast polycrystalline copper and brasses were reduced 40 per cent by rolling, recrystallized to a common grain size of 0.045 mm. and then rolled directly to foil 0.002 in. thick. Hardness readings employing both the Vickers and Rockwell machines were taken at intervals during the reduction. For comparison, similar specimens were cross-rolled-i.e., turned through 90 for each pass-and comparable hardness data were secured. Finally sections from the single crystals of brass were cut to obtain the following initial orientations; these sections were rolled, hardness data secured and a complete micrographic record of structural changes obtained:

Jan 1, 1941

Jan 1, 1929

By Don Simon

In the late 1960s the mining industry was in an apparent slump due to a combination of factors. Enrollment dropped significantly at schools offering mining engineering degrees, resulting in a shortage today of experienced mining graduates to staff middle management positions. How has this limited supply affected salaries? Does the shortage impair the mining industry's ability to respond to national energy needs?

Jan 12, 1979

By R. W. Raymond

There is apparently no end to the doubts, inconsistencies and absurdities in which the courts of our mining States and Territories are involved in their attempts to apply to conditions of ever-increasing complexity the provisions of our anomalous mining law. In previous papers, I have called this statute " the law of the apex," because it based upon that vague, novel and mysterious condition the most important grant of title. But the apex is scarcely a more essential feature than the end-lines and the side-lines; for the rights which it may confer may be limited in various ways by these; so that we have, in many a case, the most ridiculous result that the United States, in return for the money of a citizen, conveys to him with much solemnity, under its broad seal, nobody knows what, bounded nobody can tell how. A decision recently made at Butte by Judge De Wolfe, of the United States District Court of Montana, in the case of King et al. vs. The Amy and Silversmith Mining Company, furnishes a fresh illustration of this criticism. The diagram on the following page, constructed without precise regard to courses and distances, simply to assist in the statement of the essential features of the case, will, 1 hope, make clear the principles . involved : The plaintiff occupies a location (the Nonconsolidated) adjoining on the north the defendant's location, a b c d (the Amy), and the disputed mining-ground lies, let us say, in depth under the point W, that is, on the dip of the vein, VD, but not under the surfacelocation, a b c d. The defendant has the prior title, and claims this ground under its extra-lateral right. It is admitted that the apex does not cross the end-line, a d, and does cross the side-line, a b. Whether it crosses, at the other end of the location, the end-line, b c

Jan 1, 1889

By Cloyd M. Smith

B. F. TiLLson*— The manifold difficulties of accurate anemometry in irregular sections of mine passageways, the irregular distributions of velocities in cross sections of the same, and the disturbing influence of the observer upon the air flow, all indicate an undesirable inaccuracy of results obtainable by any standardized method of traversing the section by an anemometer. It seems obvious that another, and simpler, method should be used to determine the volume of air flow in mine passages, namely: 1. At appropriate locations cement or calked framework rings should be installed permanently to equalize the irregularities of sectional contour and provide a place and means of attachment for a temporary cloth brattice which bears a rigid orifice. 2. The measurement of the velocity of air flow through the orifice may then be by anemometer or, preferably, by Pitot tube measurements of the differential pressures on both sides of the orifice in accordance with the standard practices available in engineering 1iterature. † The constants may be determined for various measuring positions in relation to the resulting "vena contracta." 3. The position of the person who makes the measurements is behind the brattice out of the air stream. The Pitot tube does not offer as disturbing an obstruction as the anemometer. A recording gauge may be employed to integrate fluctuations in air flow through that portion of the mine. No traverses are required because the reading may be at a single central point. An anemometer can be used with an orifice flow. The orifice will increase the air velocity at the measuring point, with correspondingly more accurate measurements where the normal air velocity through the passageway is low. Portable brattices might be devised with the cushioning rims which would seal against irregular rock surfaces where permanent rings were not available or feasible. The development by the Ventilation Committee of standard procedures and devices for the orifice measurement of the flow of mine ventilating air might be a desirable project for this coming year. C. M. Smith (author's reply)—Thank you for your discussion of my paper on underground anemometry. Your suggested method of measuring underground air flow is a novel one which might be applicable in some situations. It should be tested along with other suggested methods in any investigation of this subject. G. E. McElroy*—In spite of the adverse publicity that vane-anemometer methods of air measurement have had in the past and that contributed by the present paper, I endorse Mr. Erickovic's statement that anemometer traversing "has proved to be widely applicable, expeditious and simple" and add that available methods are accurate enough for the purposes for which they may be used. The fact that the great majority of minor mine officials assess relative changes in rates of air flow by comparison of crude vane-anemometer measurements, known to average 20 to 30 pct high, has no important bearing on this subject, because state inspection standards were based originally on such methods of air measurement. Federal inspection standards are based on actual rates of flow as determined by traversing, and interest in traversing methods is rapidly increasing. In considering traversing methods, three aspects are of major importance: (1) the absolute accuracy of calibrations; (2) the degree of interference with normal flow conditions introduced by traversing methods designed for accurate measurement by shaft-mounted instruments; and (3) the proper "method" factor to use for approximate measurements by hand-held instruments. With respect to absolute accuracy of calibrations, we have always placed reliance on calibrations made by the National Bureau of Standards, with which manufacturers' calibrations have usually agreed very closely. It is therefore particularly disturbing to find7 that calibrations made previous to June 1947 are presumably about 5 pct in error because of excessive registry caused by the thin flat plates on which anemometers were mounted for calibration. Velocities corrected for calibration have therefore averaged about 5 pct low in all probability. In this connection, it is interesting to note that an anemometer calibrated against Pitot-tube measurement by a single-point method in the Bureau of Mines experimental coal nine in 1923 indicated this same difference of about 5 pct and that the same instrument calibrated by a traversing method in a metal mine some months later indicated a difference in the same direction of about 4 pct. These results are reported by the Bureau of Mines.8 Regarding the degree of interference, or changes in velocity distribution, caused by the position of the observer's body in traversing operations, misconceptions seem to be especially prevalent, resulting in increasing advocacy of methods, such as the "clear section" method outlined in this paper, that cause just the type of interferences that they are designed to avoid. The degree of interference for any method may be gauged easily by a few experiments with a velocity-pressure gauge connected to a Pitot tube or with an indicating velocity meter such as the Velometer. In an experiment cited by McElroy and Richardson,# a decrease of 5 pct was noted at ten widths upstream from a 6-in. plank, whereas an observer's body at about the maximum practical distance of 6 ft downstream from the instrument is only about four widths away. In the Bureau of Standards paper previously mentioned, it is recommended that supports used in calibrations be at least 16 widths downstream. In practice, therefore, a downstream position of the observer is ruled out as far as accurate measurement is concerned. Operation of the anemometer by rigid shaft support from a point outside the section is seldom practicable; however, accurate results can be obtained, with the anemometer rigidly attached to a short shaft and held at arm's length, by an observer advancing across the traversed section while he faces the opposite wall and stands sideways to the current, provided that he keeps the instrument at least 3 ft away from his body at all times and traverses the entire section with it. If the traverse can be started with the observer in a side recess, the entire section can be covered in one operation. Normally, it would be covered in two half-sections. The presence of the observer's body does not, as is commonly supposed, increase the average velocity throughout the remaining part of the section. Rather, the velocities 1 to 2 ft on either side of his body are increased, but the distribution of velocities throughout the rest of the cross section remains normal, and a traverse made as stated gives a true average velocity for normal-flow conditions. Regarding the proper "method" factor for accounting for interference in the approximate methods of traversing with hand-held instruments, here again confusion prevails, for which the writer must assume some of the blame. Comparison of consecutive traverses made by shaft-held and hand-held 4-in. anemometers in field work after the tests reported by McElroy and Richardson' gave method factors

Jan 1, 1950