Search Documents

By Ervin E. Underwood

IT has been recognized for many years that dis-persed particles have great value in raising the creep resistance of metallic alloys. In fact, some of the most successful high-temperature alloys owe their superiority to this factor above all others. A recent observation by Glen1," indicates that even better high-temperature resistance to deformation results in alloys capable of two successive precipitation reactions. The ramifications of this finding are of great interest. Unfortunately, our understanding of the reasons for such notable improvements has not kept pace with technical developments. In an effort to uncover some of the basic facts governing strengthening by particles, a program was initiated at the Battelle Memorial Institute with the primary goal of comparing creep strengths in single-phase and two-phase (precipitating) alloys. The effects of precipitation from solid solution on the creep properties of alloys are generally such that the resistance to creep is increased. However, if alloys are heat treated to different degrees of hardness before creep testing, it is often found that those possessing the maximum hardness initially do not necessarily have the maximum creep resistance. Depending on the stresses and temperatures involved other structures may prove more desirable. Considerations of the above nature indicate the importance of defining the initial state of the alloy. Here, it was decided to start with quenched single- phase alloys in which precipitation and creep deformation proceed concurrently. Equipment and Experimental Procedures Preparation of the Specimens—Four 25 lb ingots were prepared from 99.999 pct Cu and 99.996 pct Al to compositions of 1, 2, 3, and 4 wt pct Cu. Spec-trographic and chemical analyses are listed in Table I. After heat treatments and intermediate reductions, the alloys were cold rolled to 1/8 in. thick sheet. The final cold reductions amounted to 50, 40, 20, and 10 pct for the 1, 2, 3, and 4 pct Cu alloys, respectively. The specimens for creep testing were machined into tensile flats 7 in. long, 3/4 in. wide (at the shoulders), and 1/8 in. thick. The reduced sections were 1/4 in. wide and 21/2 in. long. After heat treatments at 540°C to an ASTM grain size of 1 1, the specimens were quenched into water at room temperature, then electropolished in a glacial acetic acid and perchloric acid solution. The gage marks were Knoop impressions placed 2 in. apart on the reduced sections. Blanks of 1 x 1 in, were cut from the same sheets for the age hardening runs and were given the same grain size heat treatments. The specimens and blanks were stored in a refrigerator at —40°C until needed for testing. Creep Measurements—Creep tests were conducted in a constant temperature room which was maintained at 26° ±1°C. A split-type, hinged, vertical-tube furnace was mounted on a horizontal track so that the specimen could be enclosed suddenly. Thus, it took about 15 min for the specimen to come within 5°C of the test temperature. The temperature variation along the specimen was controlled to about

Jan 1, 1958

By R. W. Smith, Z. Sadowski

The stabilities of finely divided mineral suspensions were determined as functions of pH and concentrations of polyethylene oxide, sodium ligninsulfonate, sodium dodecybulfate, and sodium oleate. In addition, the electrokinetic potentials of the minerals were determined under identical pH and additive concentration conditions. Flocculation or dispersion of the suspensions is discussed in terms of both the amount and manner of adsorption at the appropriate solid-liquid interface as it is influenced by additive concentration and pH.

Jan 1, 1986

By A. Raman

The Nb-Co system was nuestigated in the range 10 to SO at. pct Co with X-rays. A pt phase with the W6Fe.r-type structure occurs in the system between 46 and 52 at, pct Co. Its unit-cell dimensions are nearly identical to those of the p Phases found in the Nb-Fe and Nb-Ni systems. Two Laves phases, one having the MgZnz-type structure and the other the MgCuz-type structure, already t-eported in the literature, are found to exist in the system. The ,l.IgZnz-type phase occurs between 62 and 64 at. pct Co. A MgNi2-type Laves phase, reported in the literature, is no! obtained. A binalry phase is found to exist belozv I000C around 82 at. pct Co. THE cobalt-rich side of the system Nb-Co has been repeatedly investigated by previous inestiators" and the following intermediate phases are known to occur: NbCo, which crystallizes in the MgCu2-type structure and Nbc03,' reported originally by Wall-bam, which has the MgNiz-type structre. Jordan and uwez' as well as lliott' were unable to find the MgNiz-type phase. Two phases, designated as x and y, were reported by Saito and eck.' The phase x was inferred to have a narrow composition range near 77 at. pct Co. No published work is known to the author which reports the investigations in the niobium-rich portions of the system. This paper presents the results of an investigation in the Nb-Co system between 10 and 80 at. pct Co. EXPERIMENTAL PROCEDURE Two or three grams of the alloys under investigation were prepared using niobium (99.9 pct +) and cobalt (98.8 pct + with 0.14 pct Fe and and 0.03 pct C) in a tungsten-electrode arc furnace under commercial argon atmosphere. They were then wrapped in molybdenum sheets and annealed for a period between 5 days and 1 week at 1300°C in high vacuum (10-" orr) or in evacuated quartz amules for 2 weeks at 1000°C. Powders of -325 mesh size were prepared for X-ray work by crushing and grinding the specimens. Subsequent reannealing of the powders was not undertaken since most of the alloys were brittle and broke easily. X-ray powder patterns of the as-cast and annealed samples were prepared in a Siemens cylindrical camera (57.3 mm radius) with Cr-K, radiation. A Siemens diffrac to meter was used to get the X-ray patterns of some new phases. Metal log raphic examination of the alloys supplemented the X-ray findings. RESULTS The results of the X-ray and microstructural analysis Of the alloys are in in Table I. The lattice parameters of the phases are listed in Table 11 for quick reference. A set of micro photographs in Fig. l(n) to (j) show the microstructures of some alloys. A probable equilibrium diagram is drawn in Fig. 2

Jan 1, 1967

By Robert G. Van Nostrand, John H. Henkel

TRANSIENT potentials obtained in resistivity prospecting can be separated into two classes. The first is electromagnetic, has a comparatively short time constant, and increases in relative amplitude as the electrode separation is increased. These electromagnetic transient potentials, of which an excellent theoretical treatment is given by Yost: are the result of changes in the current and can be classed as differentiated signals. The second class is electrochemical, has a comparatively long time constant, and decreases in relative amplitude as the electrode separation is increased. The electrochemical signals are generated by the current flow itself and can be classed as integrated signals. The transient potentials due to electrochemical factors are the subject of this article. The phenomenon is referred to as induced polarization. Schlumberger" was the first worker to observe induced polarization, but he was unsuccessful in attempts to apply the principles of induced polarization in electrochemical prospecting. Other workers, notably Bleil; have studied polarization and in some cases pointed out its possibilities, but no theory has been presented that describes polarization and its time dependence adequately. It is the purpose of this discussion to present the essence of a theory to geo-physicists and to show that it leads to results consistent with experimental evidence. The theory on which this analysis is based has existed in electrochemical circles since 1910."

Jan 1, 1958

By H. B. Pulsifer

THIS paper outlines a method for rapid production of flat, granular surfaces on many of the medium hard- alloys. Grinding wheels and fabrics on wheels are not used; the purpose is accomplished by rubbing on emery papers and on fine abrasives heaped on hand boards. The advantages of chromic acid in the solutions for etching nickel and copper alloys are explained. Steels may require an additional step in the mechanical smoothing owing to the lack of an ideal etchant. Chloric acid is a. rapid etchant for steel. Thirty-six photomicrographs illustrate the steps in smoothing and the clearness with which structures can be rapidly exposed. New structures in low-carbon steels are announced. After a little practice, many materials can be finished within two or three minutes. CUPRONICKELS In the previous papers on the metallography of copper and magnesium which the author has presented to this Institute there has been an attempt to demonstrate the advantages of minimizing the mechanical work of surfacing and depending more on chemical means; the present paper continues the research into a still wider field. It is obvious that the success of a chemical method for smoothing and etching depends almost entirely on the use of a suitable reagent. The etchant must remove the surface granulations and outline the structures. A very special type of reaction between reagent and metal must be displayed. Promiscuous corrosion or the intensification of the attack about local couples -formed by impurities or components must not be in evidence. There are several reagents that etch highly polished nickel and copper alloys very well. Acidified ferric chloride solutions, concentrated and dilute nitric acid solutions, and nitric and acetic acids in acetone have -been used to good advantage for the purpose. However, if they are expected to etch rather deeply-that is, smooth as well as characterize-the results may be far from satisfactory.

Jan 1, 1928

By S. K. Ruggieri, R. A. Jankowski

Airborne respirable dust levels on longwalls can be reduced if operators approach the dust control problem in a logical and fundamental manner. This can be accomplished through the proper application and continued use of effective dust control techniques. The Bureau of Mines is currently assessing the effectiveness of longwall dust control techniques in use today to provide mine operators with guidelines for selecting the most appropriate control technology. This paper presents a fundamental approach to the problem of shearer dust control. Three dust control techniques to be discussed are: deep cutting/increased pick penetration for reducing the amount of respirable dust generated; drum water sprays/improved water supply system to suppress the amount of airborne respirable dust; and improved external water spray system, the “shearer-clearer, "to push the dust close to the face. The techniques have been evaluated infield trials and have been shown to be both practical and effective in applications to control shearer generated dust.

Jan 1, 1985

By William B. Phillips

The concentration of natural magnetites has been carried on in this country for several years, and more or less information has been collected on the subject. Various inventors, availing themselves of the magnetism which is inherent in such ores, have devised machines for separating the impurities from the ore by means of the electric current; and a greater or less degree of success has rewarded their painstaking and persevering efforts. We are now fairly in position to judge of the value of the process as applied to such material. It is not my purpose to speak of this matter further than may be required by the emergencies of the case. I shall assume that most engineers and metallurgical chemists are already acquainted with what has been done at the Chateaugay mines, at Mineville, at the Benson mines, at the Weldon and Ogdensburgh mines, and at Cranberry; although, at this latter place, there has not been so much done as we could wish. I shall not now speak of the various types of separators. From the time of William Fullarton, to whom was granted an English patent, in 1792, for separating iron-ore by the application of magnetic attraction, down to the present time, a great. many devices have been suggested, and a great many patents taken out for this purpose; but it is not necessary now to enter upon a discussion of their merits. Perhaps, at some future meeting of the Institute, after we shall have experimented further with some of the machines on the market, there may be an opportunity to contribute something to the current knowledge of the efficiency and economy of separating-machines. In this paper I propose to give, as briefly as possible, the results already reached in converting a non-magnetic ore into magnetic ore, and then concentrating it over a magnetic separator of the alternate-polarity type. I am aware of the work

Jan 1, 1896

CARACAS PETROLEUM Established February 24, 1957 Official year begins in January Harry J Sykes, Chairman G J Clarke, Vice-Chairman Robert S Longwell, Vice-Chairman David L Stepanek, Treasurer Robert C Newman, Secretary Texas Petroleum Co Apartado 267 Caracas, Venezuela

Jan 1, 1960

By Arthur F. Taggart

In 1900, Elmore found that if an acidulated pulp was stirred up with an oil which was relatively insoluble in and lighter than water, and the mixture was allowed to stratify, much of the sulfide would be found hanging to the lower surface of the floating body of oil and could be skimmed off or overflowed with it. The action of the flotation agent here is twofold, first to select the sulfide from the gangue—what today is called collection—and second, to buoy the collected sulfide away from the gangue. The action in collecting is illustrated by Fig. 1: which contrasts the behavior of drops of oil brought, under water, to the surfaces of gangue and sulfide particles, respectively. The oil displaces water from the surface of the sulfide; the water displaces oil from the gangue surface. If, instead of considering the solid particles the fixed parts of the system of oil, water and solids. we consider the oil and water fixed and the solids presented to the surface of contact, the condition will be as shown in Fig. 2; the sulfide tends to be drawn into the interface and the gangue to be excluded. The sulfide particles are held in the oil-water surface by the tension of this surface. The buoyant effect is supplied by the oil droplets in bringing the sulfides to the water surface, but not in holding them there. Gas as Buoyant Medium of Flotation In 1906 Sulman. Picard and Ballot discovered a practical and substantially fool-proof method of doing what Everson, in 1886, and Fro-nlcnt. DeBavay Bessel and Elmore had been doing in the intervening years, viz.: using gas in place of oil as the buoyant medium for flotation, but retaining oil as the agent. To all of these inventors "oil," with no qualification as to its kind and no true understanding of its function, was the important thing. Hut they placed on the oil an additional burden viz.: froth-making, and it soon became apparent that not all oils were suitable for the dual purpose. As a matter of fact, it is probable that each of these inventors knew only one suitable oil at the time he wrote his patent, but used the generic term in the patent with the usual idea

Jan 1, 1928

By C. P. Sandberg

Notwithstanding the growing importance of this subject, no work specially devoted to it has hitherto been published. Having had to inspect during the last twenty years nearly a million tons of iron and steel rails for various countries, I have obtained experience of what rail manufacturers can practically execute, as well as of what railway engineers practically require. Bearing these two points in mind, I have from time to time published observations with a view to unite both interests,—that of the producer and that of the consumer,—and to reduce the specifications and the forms of sections to standards, or types, in order to facilitate the execution of the works and to improve the construction of permanent way. The Swedish government railways, as well as private companies owning railways in Sweden, Norway, and Denmark,.have during the time above mentioned consulted with me and intrusted to me their rail inspection. I therefore owe to these countries much of the opportunity which I have enjoyed of gaining experience and position. Next to Sweden, America is the country which has most liberally favored me with its confidence in placing these matters in my hands. Through circumstances not under my control there has been little exportation to, and less work done by Europe for, America during the last six years; but the recent revival of the rail trade has been the more gratifying to mo, seeing that almost all the importers of American rails are still specifying for the Sandberg rail sections and inspection. It is therefore with feelings of gratitude that I now beg to lay before the American Institute of Mining Engineers, and I hope, through that body, before the American railway world, the results of some experience which I have gained in the execution of work for their country, and which therefore belongs rightfully to

Jan 1, 1881

By C. P. Sandberg

INTRODUCTION. NOTWITHSTANDING the growing importance of this subject, no work specially devoted to it has hitherto been published. Having had to inspect during the last twenty years nearly a million tons of iron and steel rails for various countries, I have obtained experience of what rail manufacturers can practically execute, as well as of what railway engineers practically require. Bearing these two points in mind, I have from time to time published observations with a view to unite both interests, -that of the producer and that of the consumer,-and to reduce the specifications and the forms of sections to standards, or types, in order to facilitate the execution of the works and to improve the construction of permanent way. The Swedish government railways, as well as private companies owning railways in Sweden, Norway, and Denmark, have during the time above mentioned consulted with me and intrusted to me their rail inspection. I therefore owe to these countries much of the opportunity which I have enjoyed of gaining experience and position. Next to Sweden, America is the country which has most liberally favored me with its confidence in placing these matters in my hands. Through circumstances not under my control there has been little exportation to, and less work done by Europe for, America during the last six years ; but the recent revival of the rail trade has been the more gratifying to me, seeing that almost all the importers of American rails are still specifying for the Sandberg rail sections and inspection. It is therefore with .feelings of gratitude that I now beg to lay before the American Institute of Mining Engineers, and I hope, through that body, before the American railway world, the results of some experience which I have gained in the execution of work for their country, and which therefore belongs rightfully to

Jan 1, 1881

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By Howard N. Eavenson

ALL of the matters so far taken up by the Institute Committee on Stabilization of the Coal Industry will be of help, but it seems to be that under present conditions not very much can be expected until the railroad situation has been improved. As an instance of this, I would cite the fact of our experience at our mines in West Virginia and Kentucky. During 1917 and 1918 at our West Virginia plants we produced for our own consumption, practically entirely in the Chicago district, about 4,750,000 net tons of coal. In 1919 our output was reduced to 3,500,000 tons, this being caused partly by the shortage of orders in the few months following the armistice, but more particularly by The car shortage which began last September and continued throughout the remainder of the year, with the exception of December. This car shortage has been more acute since the first of the year, and while we now have an actual capacity here of 20,000 tons daily and have the equipment to produce it, with the possible exception of a few houses, we are able to average only about 12,000 tons, and in consequence, about 30 per cent. of our by-product ovens in the Chicago district are idle, and a number of blast furnaces are down for the want of coke. These figures, of course, refer to conditions before the strike of switchmen in April was started.

Jan 1, 1920

By F. G. Jaicks

RECOGNITION of the benefits to be gained from the continuous casting of molten steel into finished or semifinished products has been given by scientific minds since the very beginnings of steel plant technology. In fact, Sir Henry Bessemer is credited with the first of a long list of patents' issued by the U. S. Patent Office for a process which would accomplish this desirable end. None of these early ideas attained practical success and, as a result, the conventional method of teeming into ingot molds became an integral part of modern steelmaking operations. This procedure, although refined to keep pace with the changes which have come about in steelmaking and finishing facilities, is recognized to have inherent shortcomings which adversely affect manufacturing costs and steel quality. Interest in the continuous casting of steel persists because the process is directed toward avoiding some obvious weaknesses of conventional ingot casting. It has been recognized that should it be possible to substitute any of the continuous casting techniques under current development for ingot casting, it would no longer be necessary to make large capital investments in primary rolling equipment, the sole purpose of which is to reduce ingot castings to a form rollable on finishing mills. The results reported in the continuous casting of non-ferrous metals and specialty steels indicate that in addition to avoiding the primary rolling mills there is some basis for expecting significant improvements in yield, surface, and internal quality. Recognizing the shortcomings of the conventional procedures, the Inland Steel Co., in cooperation with Atlas Steels Ltd. and the Freyn Dept. of the Kop- pers Co. Inc., embarked upon a program to evaluate certain aspects of continuous casting in order to determine whether the process could be applied practically to an existing integrated steel plant producing 'large tonnages of carbon steels. TO assist in this evaluation a study was carried out in which several types of low carbon steel were continuously cast in an existing machine. It is the purpose of this paper to review some of the results obtained in the casting studies and to interpret the information that was obtained so as to indicate factors that must be considered in assessing operating limitations and plant capacities. Despite the early interest in the continuous casting of steel, the actual application to the steel industry is relatively recent. At present, there are about 25 operating plants casting steel, most of which have been built in the past decade. None of these plants could be classified as large in terms of the tonnages that are being processed by the major integrated steel plants. In contrast to the situation in the steel industry, there has been widespread adoption of the continuous process in the casting of nonferrous alloys, particularly aluminum and copper. As a result, much of the basic information that was required to apply the process to steel was developed in the nonferrous industries. In this respect, a most important contribution was the development of the Junghans2 system, which was initially designed for the casting of nonferrous metals and later applied to the casting of steel. Alternative methods for casting have also been proposed by Babcock and Wilcox Tube Co.,'" the British Iron and Steel Research Association,5 and the Gebruder Bohler A. G.13 Each of these methods is now being used successfully for the casting of special steels in small experimental plants or in modest sized commercial steelworks. The Original Junghans process was first developcd in Germany. Further application of the process has been made by Rossi in other countries.'*' The experi-

Jan 1, 1958

By Edwin Dudley Martin

DURING the past twelve years the iron and steel industry has made a major advance through the development of the continuous wide strip rolling mill. So far-reaching have been the results that not only has a better product been sold at a lower price but this improvement in quality has permitted manufacturers of products using steel to make important savings in the cost of fabrication. The net result has been a better product at lower cost to the consumer without reduction in either employment or of wages paid within the industry. That is why the iron and steel industry is proud of its attainment. Being a basic industry of strategic importance, such an advance in technology has had its effects on our internal economy, our standard of living, and our industrial power as a nation in both peace and wartime.

Jan 1, 1939

By F. W. Jessen

The Mechanism of solution of salt and mixed halites of sodium and potassium is reviewed. The variation in the rate of salt removal under both laminar and turbulent flow conditions is discussed. Many changes are possible in the development of solution cavities whether used for production of salts or for storage of hydrocarbons. The parameters influencing the type and shape of cavity formed with single well or multiple well systems are examined and information presented regarding field application of techniques developed and the means of controlling overall configuration of solution cavities.

Jan 1, 1972

By J. L. Huitt, B. B. McGlothlin, J. J. Day

Laboratory tests were made with pure minerals and actual reservoir rock samples to study the effects of hydrothermal (steam m hot water) treatments on reservoir rock properties. These tests showed that hydro-thermal treatment of many reservoir rocks can result in significant rock softening. The softening was attributed primarily to the partial destruction of dolomite and kaolinite and the synthesis of montmorillonite in the presence of excess silica. In many cases, the softening was great enough to cause considerable healing of propped fractures; therefore, a serious reduction in welt productivity could result. In other tests it was found that the addition of ammonia to a hydrothermal treating fluid in a concentration as low as 0.013 Ib/lb of water not only could prevent rock softening but could cause rock hardening. The results of X-ray diflraction analyses of rock samples showed that when ammonia was added to the treating fluid, ammonium-mica and analcite were formed instead of montmorillonite. No significant permeability damage was observed in the sandstones that were subjected to the ammonia-hydro-thermal environment; in some sandstones, permeabifity improvements resulted. INTRODUCTION As the use of steam or hot water becomes more prevalent in well stimulation methods. the need for information on the effects of such treatments on reservoir rock properties becomes increasingly apparent. Several works have been published on high-temperature changes in rock properties,',' but these are more applicable to in situ combustion operations than to steam or hot water injection processes. The mineralogical literature contains many publications which report on the changes occurring with various pure minerals in hydrothermal systems. A review of this literature denotes the ease with which entirely new, crystalline mineral phases can be synthesized from other minerals in hydrothermal environments at temperatures, pressures and residence times typical of those encountered in oilfield thermal recovery or stimulation processes. Discussions of many of these experiments are given by Deer et al. Grim,' Roy et al., Zen\ and Hawkins.' One of the most significant of these pure mineral studies is the hydrothermal synthesis work of Levinson and Vian" in which montmorillonite was synthesized from naturally occurring minerals; i.e., kaolinite, quartz and carbonate minerals (particularly dolomite). These reactions occurred at 575F in only 2 days and at 300F in 5 days. These results may be applicable to petroleum reservoir rocks since the minerals studied were those which are commonly found in sandstones. Furthermore, the environmental conditions imposed in the studies were very similar to those involved in thermal stimulation of petroleum reservoirs, e.g., steam or hot water injection. Other studies have suggested that weak rocks could be hardened by "electrochemical induration", a process in which an electric current is applied to a clay-containing rock body. These tests can be regarded as hydrothermal treatments since they were conducted in some instances with aqueous solutions and since clay temperatures during the electrical treatment reached a maximum of about 100C. Although a number of studies of the reaction of pure minerals have been reported, very little has been published on the reactions of petroleum rock-hydrothermal systems. No work has been reported on preventing the more detrimental rock changes in rock softening which might occur during the injection of steam or hot water into reservoirs. The studies described in this paper were conducted to provide such information. EXPERIMENTAL APPROACH The laboratory tests included studies of the effect of hydrothermal treatment on core samples from several different reservoirs. The hydrothermal treatments (simulated steam treatments) were conducted with distilled water at 575F, for the most part, for periods of 2 to 6 days. This temperature level was selected because it represented that temperature which would probably prevail in several cases under consideration for steam injection projects. The core samples, as well as the pure mineral samples, were contained in high-pressure stainless steel, autoclave-type pressure vessels. The effects of the hydrothermal treatments were evaluated by measuring the penetrometer hardness, formation rock embedment strength and permeabilities of the core samples before and after the treatments (Fig. 1)'" In addition, the mineralogical changes in the specimens were studied by X-ray diffraction. Concomitant with the core sample studies, the mineralogical changes were studied in greater detail by conducting hydrothermal synthesis experiments with pure minerals at similar temperature levels and residence times. For the most part, samples of finely-crushed pure dolomite.

By F. E. Bash

About three years ago, the writer presented a paper1 on the rate of heating and cooling of a 24-in. round ingot. The present paper deals with work done on larger ingots at the plant of the Allis Chalmers Mfg. Co., Milwaukee, Wis., in August, 1919. Sufficient data on ingots of all sizes were desired to enable one to calculate in advance the rate at which any ingot could be raised to a forging temperature without injury to the steel, determining also the temperature gradient between different sections of the ingot and the length of time necessary to heat to the center. This has now been experimentally determined for 24-in. and 45-in. ignots by the writer and for a 18-in. cube by E. F. Law.2 J. F. Harper has also made tests on heat-treating temperatures on 30-in, ingots; which data are included in this paper. No attempt is made here to work out a formula for the heat penetration of steel, for too many factors are involved concerning which we have not sufficient information, as for instance, the specific heat of steel up to 2300' F. It is hoped that eventually a set of formulas will be developed so that one may calculate maximum allowable temperature differences within an ingot for any particular kind of steel and the rate of absorption of heat and temperature gradient within the ingot for a definite temperature head. EXPEEIMENTAL INGOT The ingot tested was 45 in. in diameter, having been forged into the shape shown in Fig. 1 from 54 in. diameter. Seven -in. holes were

Jan 1, 1923

By F. E. Bash

About three years ago, the writer presented a paper1 on the rate of heating and cooling of a 24-in. round ingot. The present paper deals with work done on larger ingots at the plant of the Allis Chalmers Mfg. Co., Milwaukee, Wis., in August, 1919. Sufficient data on ingots of all sizes were desired to enable one to calculate in advance the rate at which any ingot could be raised to a forging temperature without injury to the steel, determining also the temperature gradient between different sections of the ingot and the length of time necessary to heat to the center. This has now been experimentally determined for 24-in. and 45-in. ignots by the writer and for a 18-in. cube by E. F. Law.2 J. F. Harper has also made tests on heat-treating temperatures on 30-in, ingots; which data are included in this paper. No attempt is made here to work out a formula for the heat penetration of steel, for too many factors are involved concerning which we have not sufficient information, as for instance, the specific heat of steel up to 2300' F. It is hoped that eventually a set of formulas will be developed so that one may calculate maximum allowable temperature differences within an ingot for any particular kind of steel and the rate of absorption of heat and temperature gradient within the ingot for a definite temperature head. EXPEEIMENTAL INGOT The ingot tested was 45 in. in diameter, having been forged into the shape shown in Fig. 1 from 54 in. diameter. Seven -in. holes were

Jan 1, 1923

By R. E. Carter, F. D. Richardson

Self-diffusion coefficients have been measured for iron in wustite (700° to 1000°C) and for cobalt in cobaltous oxide (800&apos; to 1350°C) by means of radio-isotopes. Both sectioning and decrease of surface-activity methods have been used and a particular shortcoming of the latter method has been disclosed for wustite. The effects of oxygen pressure on the composition of cobaltous oxide and on the diffusion coefficient of cobalt in the oxide have been established. The effect of the preparation conditions of the cobalt-oxide specimens on the diffusion measurements has been determined. It has been concluded that diffusion of cobalt occurs via vacant cation sites and that a cobaltous-oxide disk reaches equilibrium with its environment in a time which is very short compared with that needed for diffusion of the radio-isotope. THE availability of radioactive isotopes in recent years has permitted the measurement of many self-diffusion coefficients which were hitherto impossible to determine. With the advent of radioactivity, the method of measuring diffusion coefficients has also changed. The earlier sectioning method by which the concentration profile of the diffusing species was determined in the diffusion specimen has often been rejected in favor of the decrease of surface-activity method first developed by Von Hevesy,&apos; and extended by Steigman, Shockley, and Nix,&apos; and Raynor, Thomassen, and Rouse." With the experimental arrangement where an infinitely thin deposit of tracer is diffused into a semi-infinite cylinder, the decrease in activity of the active face due to diffusion of the tracer into the specimen is measured by counting the active face before and after diffusion. Under these conditions, the appropriate solution of the diffusion equation is R = e*(l-<K/Z) [1] where R is the ratio of the counting rates after-to-before diffusion, $& is the Gaussian error integral of \/Z, and Z is defined as Z = p2Dt, p being the linear-absorption coefficient of the detected radiation in the diffusion specimen, D the self-diffusion coefficient, and t the diffusion time. In the older sectioning method the concentration distribution of the tracer is found after diffusion by analysing thin parallel sections cut from the active face of the diffusion specimen. As seen from the solution of Fick&apos;s second law for the distribution of an infinitely thin source after diffusion into a semi-infinite cylinder the log of the concentration plotted against x&apos; will be a straight line of slope log e/4 Dt. The diffusion coefficient thus can be calculated directly. The units of the tracer concentration are completely arbitrary, since any change in units does not change the slope of the log c vs x2 lot. Although both of the above methods have been widely used, a thorough experimental comparison does not appear to have been made. Birchenall and Mehl,&apos; during an investigation of the self-diffusion rate of a and r iron by the surface method using Fe" tracer, diffused and sectioned one welded couple. The diffusion coefficient from this run agreed with those by the surface method. Buffington, Bakalar, and Cohen," during an investigation on a and y iron

Jan 1, 1955