Search Documents

By S. E. Bronisz, R. E. Tate

s-plutonium samples possessing a strong growth texture have been produced by allowing them to transform under pressure from p to a. A fiber texture with [010] parallel to the pressure axis results. The textured samples are expected to be useful in determining the effects of crystallographic orientation on the physical properties of a plutonium, and initial results of measurements of resistivity and mechanical properties are described. THE crystal structure of a plutonium1 is mono-clinic, P21/m, and many of the metal's properties should reflect the crystallographic anisotropy. Unfortunately, it has not yet been possible to grow useful sizes of single crystals of a plutonium. Therefore, few of plutonium's orientation-sensitive properties have been determined as a function of crystallographic orientation. One way to gain information about at least some of the orientation-dependent properties is to study a highly textured sample. Such samples have been produced by cold rolling a plutonium,2 but they are necessarily very small in one dimension. We have now successfully used two other techniques to produce highly textured samples, not limited to small thicknesses. METHODS OF PRODUCING PREFERRED ORIENTATION The texture is produced by causing the plutonium to transform from ß to a while under pressure. It was observed by Gardner3 that applying a compres-sive load during the transformation resulted in the formation of columnar grains of a plutonium, and Cramer4 observed a similar structure in some diffusion couples rolled in the P phase. Neither of these workers, however, investigated the subject beyond these observations. The more flexible of the two methods developed is that of compressive loading. The technique is to enclose a sample of plutonium in a die assembly before applying the load. It is possible, of course, to dispense with the die and simply press the sample between two platens. In this case, however, the unrestrained sample deforms during the pressing, making it difficult to maintain the load and to control the final sample thickness. This compressive loading technique has been used on specimens ranging from 1/4 to 3 in. diameter, with height-to-diameter ratios ranging from 5 : l to 1:6. The procedure begins with loading the sample, a right cylinder of a plutonium, into the pressing die. Plastic deformation of the sample while it is being pressed is minimized by machining the sample so that its diameter is nearly the same as that of the die barrel. Then the loaded die assembly is placed in a vacuum pressing can that fits on a hydraulic press. After a vacuum is achieved the die assembly is heated to 180°C and equilibrated. The load is then applied and the specimen and die are allowed to cool to about 40° to 50°C before the pressure is removed. The resulting sample is composed of rod-shaped a -plutonium grains, the rod axes being parallel to the cylinder axis and the pressing direction. Photomicrographs of the oriented structure are shown in Fig. 1. Although most of the specimen is composed of grains whose rod axes are parallel to the cylinder axis, a thin, peripheral layer consists of rod-shaped grains whose rod axes are perpendicular to the cylinder axis. Presumably, the highly plastic nature of p plutonium leads to approximately hydrostatic conditions during the initial stages of the P — a transformation under pressure. At this time, the grains in the peripheral layer would have grown parallel to the local force direction. During the latter stages of the transformation, the accompanying volume contraction would have eliminated the radial forces, leaving only the axial force and resulting in the growth of the observed structure. The growth texture did not form without the application of pressure. Attempts were made to produce the texture by repeating the standard temperature cycle without

Jan 1, 1965

By Magnus Troilius

INTRODUCTION BY C. P. SANDBERG. SINCE the discussion On steel rails in America has forcibly drawn attention to the value of chemical analysis, if not as a necessary stipulation, at least as a guide to control the usual mechanical tests, some doubt has been thrown upon the accuracy of the analytical results Obtained by different chemists. To any One having the least acquaintance with chemistry., it is quite clear that if exactly similar results are to be obtained from the same borings of steel, exactly the same methods must be used by the different analysts. Hence the necessity (if complications are to be avoided) of establishing what I may call standard or normal methods, to be used both by the inspectors and by the chemists at the works. Remembering that the application' of chemistry to steel-rail inspection is yet in its infancy, it is of great importance to possess a perfect acquaintance with the best methods in use. Being myself a grateful pupil of Professor Eggertz, of the School of Mines in Sweden, it Occurred to me, two. years ago, that I could not do better than start a laboratory of my. own, and engage One of his pupils, Mr. Troilius, for the purpose of analyzing the steel borings from mechanically-tested rails, so that I might thus Obtain without delay thoroughly accurate determinations. Moreover, in Order to carry on the, operations in perfect accordance with the methods used at the steel works in England and Germany, where I had to control the manufacture, I deemed it desirable to allow Mr. Troilius to go through a course of training at these works; and I gladly seize this opportunity of expressing my grateful acknowledgments to several works in England and in Germany for affording every facility for such an exchange of information as was found necessary in arriving at the best analytical methods to be used.

Jan 1, 1882

By William Kelly, F. H. Armstrong

The object of this paper is to describe the electric equipment at the iron-ore mines of Penn Iron Mining Co., Vulcan, Mich. and of Republic Iron Co., Republic, Mich.; to give the results of tests; and to discuss the methods in use from an operating as well as from an efficiency standpoint. Electricity was introduced at the Penn mines for pumping, hoisting, and compressing air in the spring of 1907, upon the completion of a hydro-electric plant built by that company on the Menominee river about 4 miles from the mines. This plant was described in a paper1 presented before the Lake Superior Mining Institute. A paper2 presented at a meeting of the same Institute describes some of the operating features, and the safety devices of the electric hoist at the Curry shaft were briefly described in the Proceedings of the First Co-operative Safety Congress held under the auspices of the Association of Iron and Steel Electrical Engineers at Milwaukee, Wis., Sept. 30 to Oct. 5, 1912. Generating PoweR Plants After the success of electrical operation was assured, a second set of water wheels and generator was installed at the falls, for which provision had been made in the original design and in the construction of the foundations, and later three additional wires were added to the main transmission line, doubling its capacity and reducing the line loss. The general conditions of this installation are particularly favorable for hydro-electric operation. In the neighborhood of three-fourths of the power used is for mine pumping, which in the main is regular and continuous. For air compressing, power is used for about 18 hr. a day for five days, and 9 hr. for one day in the week, though occasionally when shaft sinking is going on a very small amount of compressed air may be

Jan 1, 1915

By E. A. Gulbransen, K. F. Andrew

In a recent communication14 we have reported on the kinetics of the reactions of zirconium with O2, N2 and H2 as a function of the time, temperature and pressure variables. A systematic study was made and the results correlated with fundamental theories of gas-metal reactions. This paper will present a similar study for titanium. Titanium and zirconium are members of the IV group of the periodic table and possess many similar physical and chemical properties as a result of their similar electronic configuration for the outer electrons. The two metals are relatively inert to both gas and liquid phase corrosion at room temperature. However, at moderate temperatures the metals become active and react readily with the common gases including O2, N2 and H2 which are of interest in this study. A study of the kinetics of these gas-metal reactions is of interest for three reasons: (1) to understand the rate of reaction of titanium and its role in the behavior of high temperature alloys; (2) to understand the practical difficulties of the reduction, refining and working of titanium; and (3) to correlate the data with fundamental theories of gas-metal reactions and crystal structure predictions. Literature Survey Several review papers8 and books4243 exist on the preparation and properties of titanium and its alloys. THE METAL Titanium has, at room temperature, a hexagonal lattice of the zinc type. Hagg19 gives a value of 2.953A for the (a) axis, a value of 4.729 for the (c) axis and a density of 4.427 at 20°C. Burgers and Jacobs6 have observed the transformation of the hexagonal to the body-centered cubic structure at 880°C and have established a value of 3.31 for the cube edge and a density of 4.31. TITANIUM-OXYGEN Carpenter and Reavell6 using a pressure change method have studied the reaction at temperatures of 742° and 1000°C and for a pressure of one-fifth of an atmosphere. The probabilities for reaction are calculated from kinetic theory and they report a value of 10-5 for O2 at 1000°C and 10-6 at 740°C. The titanium-oxygen system has been investigated by Ehrlich.10,11 Five phases are observed. Between (TiO2 and TiO1.90) an alpha-phase, consisting ofarutile lattice, is found. A beta-phase is observed between (TiO1.80 and TiO1.70). A gamma-phase is homogeneous between (TiO1.56 and TiO1.46) and has a structure of the corundum type. The delta-phase exists between TiO1.25 and TiO0.6 and has a sodium chloride structure. From TiO0.42 to Ti the metal structure is observed. The surface oxide films have been studied by Hickman and Gulbransen.20 The rutile structure is observed in the temperature range studied, 300 to 700°C. Three crystalline modifications of TiO2 exist: rutile and anatase which are tetragonal and brookite which has an orthorhombic structure. Anatase is reported36 to exist in two forms: I and II. Anatase II changes to anatase I at 642°C. Anatase I is stable up to 915°C where rutile becomes the stable modification. At 1300°C rutile transforms to brookite which melts at 1900°C. The monoxide, TiO, may be prepared from the dioxide by high temperature reduction with carbon or magnesium. Its melting point is 1750°C. TITANIUM-NITROGEN Carpenter and Reavell6 report that at 1000°C a linear rate law is observed. The probability of reaction is given as 10-8 at 1000°C. Fast12 has studied the solubility of nitrogen and its effect on the mechanical properties of the metal. The crystal structure of TiN has been shown by several workers2'21'44 to follow the sodium chloride structure. However, the calculated density is found to differ from the pycnometric value. This is studied by Brager3,4 in detail. He has suggested that the titanium sites in the lattice are only partially filled at low temperatures. As the temperature of preparation is raised the vacant sites become occupied which expands the lattice and increases the hardness and density. An (a) value of 4.22Å is given for room temperature. TITANIUM-HYDROGEN The solubility and the crystal structures observed in this system have been reviewed in a recent book by Smith.40

Jan 1, 1950

By S. C. Jones, J. A. Davis

This paper describes displacement mechanisms of micel-lur solution slugs, displuced by a thickened water "mobility buffer", in a glass micromodel and in consolidated Berea sandstone cores. Colored motion pictures, taken through a microscope, recorded interactions on a pore-to-pore bash in the micromodel. Production and differential pressure data from consolidated cores previously waterflooded to residua1 oil saturation revealed displacement mechani.sm.s macroscopically. Oil is displaced miscibly, while interstitia1 water is displaced immiscibly by the injected micellar. solution slug. Part of this water is dispersed and carried near the lead ing edge of the .slug, and some may remain as a residual saturation. Thickened water displaces any residual water. It also emulsifies with the. slug material, thereby displacing it. The displacement sequence forms banks of oil and water with relatively constant fractional flows, saturations, and mobilities. The mobility of oil and water flowing ahead of the .slug defines .slug viscosity required for stable displacement. Equations are presented that describe. several aspecis of the displacement flow behavior: oil breakthrough, oil cut during production of the stabilized bank, breakthrough of banked water and the resulting decreased fractional flow of oil, fluid mobilities, etc. Breakthroughs, calculated from the equations, are compared with experimental data. Slugs of micellar sollution, ranging from 1 to 5 percent PV, produced unusually high oil recoveries (up to 100 percent) in previously waterflooded consolidated cores. Investigation of the effect of mobility buffer size on oil recovery indicated that recovery is reduced in 3-in. X 4-ft cores for mobility buffer sizes .smaller than 50 percent of the pore volume. Introduction A new oil recovery process,* conceived in 1962, utilizes a slug of micellar solution' that has sufficient viscosity to avoid an unfavorable mobility ratio with respect to the oil and water it displaces. These micellar solutions are composed of hydrocarbons, water, and surfactants, and may contain electrolytes and co-surfactants. The micellar solution is displaced by a "mobility buffer". The mobility buffer is a bank of reduced-mobility fluid, preferably an aqueous polymer solution. The entire system is displaced by unthickened water. This paper describes some of the microscopic and macroscopic displacement mechanisms observed during laboratory development of the fluids for a potential field test. Microscopic phenomena were observed photographically in a specially constructed glass flow model and macroscopic data were taken from constant rate, tertiary displacements conducted in Berea sandstone cores. Qualitative Description of Micellar Solution Flooding This section qualitatively describes displacement mechanisms that occur when a slug of micellar solution is injected into a previously waterflooded core. The slug completely removes oil from the portion of core it contacts, and banks oil in the process. The oil saturation in this bank and the flowing WOR reach definite, fixed values that are determined by water and oil mobilities and slug characteristics. This zone of constant WOR and oil saturation will be called "stabilized oil bank" in the following discussion. When this stabilized bank reaches the outlet end of the core, the oil cut jumps from zero to a constant value equal to the fractional flow of oil. Saline water has little or no solubility in the slug. Because of this. the slug displaces in-place brine immiscibly. During slug injection, most of the brine is displaced ahead of the slug, some is carried along in the leading portion of the slug, and part of the brine may become immobile. The immobile, residual brine is later miscibly displaced by thickened water. Displacement of all the oil and only part of the water during slug injection results in a higher fractional flow of oil ahead of the slug than occurs when all the water is displaced after injection of thickened water is begun. The slug spontaneously emulsifies fresh (low-salt content) water. By emulsification, the slug can become infinitely diluted, and hence totally displaced, by thickened water. Fluid saturations in the core are shown schematically in Fig. 1. Parts A and B show conditions before and after the start of the thickened-water injection, respectively. Since thickened water displaces any residual brine by-

Jan 1, 1969

By William E. Ford, Edward Salisbury Dana

This section includes one distinct group, the Stibnite Group, to which orpiment is related; the other species included stand alone. Pyr., etc. - In the closed tube melts and gives a dark red liquid when hot and a red- dish yellow solid when cold; in the open tube (if heated ver slow? ) sulphurous fumes, and a white crystalline sublimate of arsenic trioxide. B.B. on ciarcoaTburm with a blue Hame, emitting arsenical and sulphurous odors. Soluble in caustic alkalies. Artif. - Realgar is frequently noted as a sublimation product from furnaces roasting ores of arsenic. Crystals are produced when arsenic sulphide is heated in a sealed tube with a solution of sodium bicarbonate. Obs. - Realgar occurs usually in veins associated with silver and lead ores. It has been found in volcanic regions as a sublimation~duct. It has also been noted as a deposit from hot spring waters. It is often rtasociate wlth orplment. It occurs at Felsi5bBnya, Kapnik and NagyAg, Hungary; Allchar, Macedonia. Binnental, Switzerland, in dolomite. In the United States, at Mercur, Utah; in the Norris Geyser Basin, Yellowstone Park, as a deposition from the hot waters. Found at the Monte Cristo millin district, Snohomish Co., Washington: the namerealga7 is from the Arabic, Rahj af gh&r,powder of the mine. Use. - Was used in fireworks to give a brilliant white light when mixed with saltpeter and ignited. The artificial material is now used for this purpose.

Jan 1, 1922

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) Mining Engineer. Graduate of Colorado School of Mines, 1912, experienced in coal, lead manganese and limestone mining, wishes execu¬tive position. A-2146. Graduate Mining Engineer.-Discharged, reserve officer, age 32, single, 7 years' experience holding responsible executive positions, in iron, copper, and talc mining. Well recommended. A-4913. Mine Manager, Superintendent or Engineer. Age 41, graduate of Michigan College of Mines; 20 years' experience in responsible positions in connection with large operations; in iron, copper, pyrites, lead and zinc mines; successful in finding and developing orebodies, increasing production, and reducing costs. Desires a position with a future. A-4081. Mining Engineer.-Graduate from Polytechnicum, Stockholm; 14 years' practical experience in Sweden, United States, Belgium, and Spain, in iron-ore development, mining, and milling; thorough knowledge of English, French and Spanish; desires position as superintendent or assistant manager. Good references; member; now in Sweden. A-4914. Research Engineer. Now in Chile on the erection of a 50-ton mill with modern machinery for the treatment of Chilean nitrate. Desires connection from the first of next year; with firm operating in South or Central America. A-4915. Metallurgical Engineer. Junior member, age 26, single, graduate Columbia School of Mines; recently discharged as lieutenant in the heavy artillery. A-4916. General Superintendent. Technical graduate, age 35, desires position over a group of four or five mines or as assistant general superintendent for a large. company. Has had experience in superintending mines, construction work, opening new and abandoned mines, safety and effi-ciency engineering and handling organized labor. At present employed by a coal company in the middle West. A-4917.

Jan 11, 1919

By W. D. Sylwestrowicz

In tests on polycrystalline copper and aluminum, the ratio of the yield stress to modulus of elasticity was found to be strongly dependent on tempemture. Also, it was shown that the change of the yield stress with temperature of a material at a given temperature and deformed to a given yield stress, but not necessarily to the same strain, does not depend on previous mechanical thermal history. Likewise, for a material at a given temperature and deformed to a given yield stress, the rate of work hardening is independent of the temperature of prior stressing. It has been shown by Los and Orowan1 and by Dorn, Goldberg, and Tietz2 that the temperature dependence of the yield stress-strain curves of crystalline materials reflects two effects: not only does the yield stress of a material in a given structural state depend on the temperature, but the structural state (and the corresponding strain hardening) after a given amount of plastic straining also depends on the temperature at which the pre-straining has been carried out. Thus, for instance, if a specimen of a ductile metal has been strained along the stress-strain curve 1 at room temperature to point A, Fig. 1, and then the straining continued in liquid nitrogen along curve NR, the yield stress A' immediately after lowering the temperature is lower than the yield stress A" of a specimen that has been strained by the same amount in liquid nitrogen (along curve 3). AA' represents the effect of the temperature change upon the yield stress of the specimen pre-strained at room temperature; A' A" is the excess strain hardening acquired if the pre-straining has been carried out in liquid nitrogen instead of at room temperature. The dependence of the yield stress (i.e., of the structural state acquired during preceding straining) upon the conditions (speed, temperature) of a pre-straining is the reason for the nonexistence of a so-called "mechanical equation of state" for plastic deformation. A 'mechanical equation of state" is a relationship of the form F(s,E, e, T) = 0, or s = f(E, E, T) [1] It was first suggested by Ludwik3 that plastic deformation might obey such an equation; this, however, was conclusively disproved by experiments of Kochendorfer.4 Additional disproofs were given in

Jan 1, 1959

By W. P. Sykes

SEVEN years ago, Dr. S. L. Hoyt1 presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned.

Jan 1, 1938

By Renato G. Bautista, Theodore D. Tiemann

A kinetic study of the hydrogen reduction of taconite from the Wisconsin Gogebic range was made over the temperature range from 500° to 1000°C on eleven size fractions from 4 to 150 mesh. Two stages of reduction were observed, a rapid initial reaction followed by a slower reaction presumably taking place at an internal receding FexO-Fe interface. Calculated mean activation energies for the two reactions were 7800 and 14,600 cal per mole respectively. In recent years there has been an increased interest in the direct reduction of iron oxide ores to metallic iron by means of gaseous reducing agents such as hydrogen and carbon monoxide.1,2 These investigations have been motivated by the desire to develop a process that will by-pass the blast furnace in the production of steel. The majority of these processes have been developed to produce metallic iron by direct reduction from high-grade iron oxide ores.3"5 Very little work has been done on the low-grade siliceous iron oxide ores.6"8 The work reported here is directed principally towards the fundamental aspect of the reduction reactions of siliceous iron oxide ores, since the practical aspects of the gaseous reductant process were discussed previously. The ore used in the investigation was obtained originally from the United States Bureau of Mines10 trench sample of the Yale member of the Wisconsin Gogebic range iron formation. The Yale taconite has an average analysis of 28.2 pct Fe and approximately 50 pct SiO2. Chemically, these nonmagnetic taconites contain on the average about 53 pct silica and 30 pct Fe. An average analysis calculated fron the USBM10 figures for a composite of the five members (Norrie, Plymouth, Pence, Pabst, and ale) of the iron formation is given in Table I. Mineralogically, based on previous X-ray diffraction and other studies, the principal minerals are hematite (Fe2O3), geothite (Fe2O3.H2O), and quartz (SiO2). Minor amounts of iron containing silicates, siderite (FeCO3) and magnetite (FeO. Fe2O3) are present.10,11 The iron minerals and the quartz are finely disseminated requiring extremely fine grinding for liberation. For the experimental work, the ore sample was screened into a number of size fractions, the analyses and densities of which are given in Table II. EXPERIMENTAL PROCEDURE The reduction experiments were carried out in a 24 in. by 2 in. ID nichrome-wound vertical-tube furnace mounted on a stand. A 1 1/2 in. OD zirconium-oxide combustion tube was used inside the furnace to contain the atmosphere. To the top of this combustion tube was joined a pyrex ground-glass joint to which was attached a glass bulb with a small (1.0 mm) opening at the center, and with two outlets controlled with a stopcock on each side. A pyrex-glass joint with connections to three stopcock joints for introducing hydrogen, nitrogen, and mixtures of hydrogen and nitrogen gas was joined to the tapered bottom of the combustion tube. The sized ore fractions were contained in a 1 in. diameter by 1 1/2 in. 150-mesh nickel screen basket. The basket was suspended in the furnace from a balance by means of a supporting nickel wire which hung freely inside the combustion tube. The furnace temperature was controlled by a Leeds and Northrup Speedomax Type G controller, connected to a chromel-alumel thermocouple placed

Jan 1, 1962

By A. Tonejc, A. Bonefacic

As can be seen from the phase diagram A1-W1 the equilibrium solubility of tungsten in aluminum is practically nil at room temperature. By quenching from the liquid state (50,000°C per sec), Varic, Burov, and Kolesnicenko2 obtained A1-W solid solutions up to 0.15 at. pct W. The quenched alloys were in the form of foils, 0.2 to 0.3 mm thick. Considering the results of Duwez and Willens,3 it is obvious that this thickness, which makes impossible a sufficiently rapid quenching, was the main reason for the relatively low content of tungsten dissolved in aluminum found by varic.2 he present note shows that the metastable solubility of tungsten in aluminum can be appreciably extended in aluminum-rich A1-W alloys. The quenching technique and the procedure employed for the preparation of the alloys have been described previously.475 The resulting quenched flakes varied in thickness from 1 to 20 µm from experiment to experiment. However, the measurements of the lattice parameters were carried out only with flakes thinner than 5 µm. The areas of quenched flakes were between 0.1 and 15 mm2. The quenched flakes were placed into a 0.3-mm glass capillary tube which was then mounted in a 114.6-mm-diam Debye-Scherrer camera. Straumanis asymmetric film position and nickel-filtered CuKa radiation were used. The lattice spacings were computed taking X(CuKa1) = 1.54050A for resolved and ?(CuKa) = 1.54178A for unresolved doublets. All specimens were rotated at room temperature, 26o +2°C. The lattice parameters were estimated from extrapolation against the Nelson-Riley function. It was estimated that the error in the lattice parameter of the measurements on a single film lies within +0.0004A for lower and about +0.001A for higher concentrations of tungsten. The lattice parameters of the metastable solid solutions A1-W are plotted vs the concentration of tungsten in Fig. 1 together with the parameters measured by previous investigators.' Each point of the present measurements represents a determination of the lattice spacing on different quenched flakes, for a given concentration of tungsten. With experimental accuracy, the lattice parameters of the metastable solid solutions fall on the straight line passing through the already known data.' As estimated from the uncertainties in the lattice spacings of the solid solutions, the alloys were homogeneous within 0.1 at. pct W. The solubility of tungsten in aluminum-rich A1-W solid solutions obtained by a very rapid quenching technique is increased to about 0.95 at. pct W. This value is 6 times greater than the amount known up to now. -he lattice parameters of the resultant aluminum solid solutions with higher concentrations of tungsten than 0.95 at. pct W did not remain constant AUGER electron spectroscopy has been used to clarify the role of impurities in the embrittlement of AISI 3340 steel. Analysis of fracture surfaces has shown that the embrittled condition is correlated with appreciable antimony segregation at grain boundaries. The low temperature (400" to 600°C) temper embrittlement of low alloy steels containing various combinations of Cr , Ni , Sb , Mn , P , Sn , and As has been examined extensively for many years. General reviews of the area have been made by McMahon1 in 1968, LOW' in 1959, woodfine3 in 1953, and Holloman4 in 1946. Recent work by Low, Stein, Turkalo, and LaForce5 has done much in separating the alloy and

Jan 1, 1970

By H. G. Doll

A new logging method, called induction logging, is described; it measures the conductivity, or resistivity, of the strata traversed by a bore hole. The apparatus, which is briefly described, comprises a coil system coupled with the ground by induction, so that there is no need for direct contact with the mud, or with the formations. For that reason, the method is particularly useful in oil base mud, and it was first applied to that case. A discussion concerning the respective contribution of each region of ground in the vicinity of the coil system is given. Through the concept of a geometrical factor, it is demonstrated that the total signal, which measures the apparent conductivity, is the summation of the partial products — geometrical factor by conductivity — for the different regions of the ground under consideration. It is thus possible to establish, for each type of coil arangement, investigation characteristic as well as departure curves and correction charts for beds of various thicknesses. This should greatly facilitate the quantative interpretation of the field logs, even in cases where such interpretation would have been difficult on electric logs taken with electrodes. It is also shown that focussing combinations of coils can be used, which give, directly on the recorded log, a value close to the true conductivity, even for fairly thin beds, thus eliminating in most cases the need for corrections. These focussing systems also give a sharper definition of the boundaries between successive strain.

Jan 1, 1949

By H. G. Doll

A new logging method, called induction logging, is described; it measures the conductivity, or resistivity, of the strata traversed by a bore hole. The apparatus, which is briefly described, comprises a coil system coupled with the ground by induction, so that there is no need for direct contact with the mud, or with the formations. For that reason, the method is particularly useful in oil base mud, and it was first applied to that case. A discussion concerning the respective contribution of each region of ground in the vicinity of the coil system is given. Through the concept of a geometrical factor, it is demonstrated that the total signal, which measures the apparent conductivity, is the summation of the partial products — geometrical factor by conductivity — for the different regions of the ground under consideration. It is thus possible to establish, for each type of coil arangement, investigation characteristic as well as departure curves and correction charts for beds of various thicknesses. This should greatly facilitate the quantative interpretation of the field logs, even in cases where such interpretation would have been difficult on electric logs taken with electrodes. It is also shown that focussing combinations of coils can be used, which give, directly on the recorded log, a value close to the true conductivity, even for fairly thin beds, thus eliminating in most cases the need for corrections. These focussing systems also give a sharper definition of the boundaries between successive strain.

Jan 1, 1949

By A. F. Giamei, E. J. Freise

A discussion of the various factors affecting the accuracy of volume fraction determination by the direct comparison X-ray diffraction method is presented. To minimize errors introduced by nonrandomization effects such as preferred orientation and large grain size, as well as errors introduced by statistical effects, an iterative mathematical analysis is introduced. This analysis is applied to all observable diffractio~ spectra from a given specimen by means of computer techniques and is statistically superior to the standard direct comparison technique which utilizes only one or tm sets of intensity spectra. The computer program also presents a graphical interpretation of- the results which enables the investigator to visualize and readily assess the scatter in volume fraction estimates caused by deviations from randomness. Finally, the iterative analysis is applied to experimental data collected from a series of plain carbon steels in both the as-received and spheroidized conditions to determine the volume fraction of cemen-tite present in each case. The results show markedly good agreement with chemical analyses for all spheroidized specimens. In theory, quantitative X-ray diffraction is a power-ful analytical technique for precise determination of the volume fractions of various phases present in a multiphase poly crystalline aggregate. There are two generally used methods; both utilize the fact that the intensity of a diffraction line of a particular phase is a function of volume fraction of that phase present in the aggregate. The more common method is the so-called internal standard technique where a known amount of standard substance is mixed with the aggregate containing the unknown. The resulting ratio of the intensity of a particular diffraction line of the unknown to the intensity of a diffraction line from the standard is used to find the weight fraction of unknown material by reference to the intensity data obtained from a previously prepared set of standards containing the same amount of standard material. The details of this technique are outlined in standard works on X-ray diffraction.' The disadvantages of the technique are that it requires the use of powder specimens and that the powder mixture must be homogeneous near the surface to the maximum effective beam depth. The alternative technique is the direct comparison method in which the ratio of the intensity of a diffraction line of a phase in the aggregate to the intensity of a second-phase diffraction line yields the ratio of the volume fractions of each phase present. This method has been applied most extensively to the determination of the percentage of retained austenite in martensitic steels and to determining the amounts of hcp and fcc allotropic modifications in pure cobalt5 and the amounts of hexagonal and rhombohedra1 modifications in graphite.8 This method is applicable to bulk as well as powder aggregates and is the technique which will be considered in the following text. It is the purpose of the present communication to show that by combining the results of X-ray diffrac-tometry with the use of high-speed digital computers the results of the direct comparison quantitative X-ray analysis technique can be optimized by using all of the data available on a diffraction pattern. THEORETICAL DISCUSSION In optimizing any quantitative X-ray diffraction experiment, the problem of accuracy vs time to collect and analyze the experimental data arises. For any method to be practical, it is required that both experimental and analytical procedures are reasonably short. In most of the previous work performed by the direct comparison method, intensity data from only one or two sets of peaks were used to calculate the volume fraction of phases present in the aggregate. Consequently, rather long-time experimental measurements are required to assure that the intensity data are sufficiently accurate to justify the use of one or two sets of data. By using computer techniques to analyze the experimental data it becomes feasible to use all of the available data on a diffraction pattern. By so doing, the time spent in measuring any one diffraction maxima can be appreciably reduced. Although this results in poor counting statistics for any one maxima, the number of data points available for analysis is greatly increased. Based on the above discussion, it will be assumed that a continuous scanning counter-diffractometer technique will be used to collect intensity data from a two-phase mixture. The integrated intensity of the ith diffraction line from the a phase in the aggregate is given by:'" where is the volume fraction of the a phase, The various quantities in Eq. [la] are angular independent while those in [lb] depend on the hkl spectrum of a particular phase. The meaning of the individual quantities in Eqs. [la] and [lb] are given in Appendix 1. It is convenient at this point to outline briefly the factors which will affect the measured intensity of any one hkl spectrum. a) Extinction effects arise from two independent experimental conditions. Primary extinction arises from a high degree of crystal perfection and results in spectra having lower intensity than predicted by Eq. [I]. Any treatment, such as powdering, which reduces

Jan 1, 1968

By H. I. Aaronson, H. A. Domian, G. M. Pound

Zener's two-parameter theory of the y a reaction in Fe-X alloys is extended to encornpass austenite-stabilizing as well as fewite-stabilizing elements, and is then cottzbitzed with statistical thermodynamic theories of Fe-C alloys to permit development of a ther-modynamic description of the proeutectoid fewite reaction in Fe-C-X alloys. Equilibrium tielines are calculated for tile a + y rep'on from experimental data and frort extrapolations of the y/y +a equilibrium surface. Sectzovs of the y/y + 0 surface are calculaled for the tzetastable sstuation LYL u-kich alloyrtg eleitzents do not partition betzseen azrstenite andfer-rite. The finding that the metastable y/a + y curves Lie close to their equilibriuwz counterparts when X = Si, .Vo, Co, Al, and Cu but well below them when X = A/ln or Ari pr-elides a thermodunamic explanation for the expcri1?7e?ztally obserted absence of partition during the proeutec toid ferrite reartlon in the fortner alloys and for the occurrence of partition at hzgher ternperatures in the latter alloys. Cotarison ofno- patitzoa free-energy changes and y/y i a curr,es in Fe-C-X alloys with the equilibrium 11al1es of these quantities in Fe-C alloys furnishes additional qualitative insight into the irqluence of allojling elements upon the kinetics of the proeutectoicl ferrite reaction. THE introduction of a substitutional alloying element, X, appreciably complicates calculation of the thermodynamics of the formation of proeutectoid ferrite from austenite. As noted in the preceding paper,' the positional entropy of the interstitial species is the principal component of the free energy of an interstitial solid solution with which theory has so far been able to deal. One would expect, however, that other components of the free energy of this type of solid solution may be significantly altered by the addition of a substitutional alloying element. Even if the assumptions are made, by analogy to the case of Fe-C alloys,' that changes in the positional entropy of carbon represent a significant part of the thermodynamic effects of an alloying element, and that the remaining effects can be taken into account by fitting the equations developed on this basis to experimental data on Fe-C-X phase diagrams or on the activities of carbon in alloyed austenite and ferrite, the experimental information available on either of these quantities is not yet sufficiently accurate or extensive, respectively, to make such an approach useful. An attempt made by Zener on the former basis to explain the effects of alloying elements on the thermodynamics of Fe-C alloys in terms of a temperature-independent "free-energy change" (actually enthalpy hane') required to transfer 1 mole of an alloying element from austenite to ferrite, in which the "free-energy change" was determined by fitting the theoretical relationships developed to Fe-C-X phase diagrams, thus proved inadequate in part because of deficiencies in the available ternary-phase-diagram data.= Other difficulties of a more fundamental nature, however, also indicated the desirability of a different approach to the problem.3y4y6 zener6 subsequently proposed that the free-energy change associated with y — a transformation in pure iron can be decomposed into magnetic and nonmagnetic components. Alloying elements were assumed to affect those components separately. One parameter was used to describe the quantitative effect exerted on each component. These parameters were evaluated from Ms (martensite-start) temperature data and from other experimental information usually either readily available or measurable with acceptable accuracy. Zener applied this treatment only to the calculation of Fe-X phase diagrams in which X is a ferrite-stabilizing element. In the present study, this treatment is extended to include austenite-stabilizing elements, and then combined with treatments previously considered for Fe-C alloys1 to permit calculation of the thermodynamic quantities of interest in the austenite - proeutectoid ferrite transformation in Fe-C-X alloys, where a number of representative, and commonly used alloying elements are chosen for X, including Si, Mn, Co, Mo, Al, Cr, and Cu. The results are used to explain important features of the partition of alloying elements between austenite and proeutectoid ferrite, as reported in a companion paper7 on the basis of electron-probe analysis, and to provide some additional understanding of the influence of alloying elements upon the kinetics of nucleation and growth of proeutectoid ferrite. Portions of this treatment6 have been clarified in the course of a review by Kaufman and Cohen.3 The consolidated summary of these developments with which this section is begun provides a basis for further clarification of the treatment, from which extension to include austenite- as well as ferrite-stabilizing elements is a natural consequence. The division of the free-energy change associated with the 7 - a transformation in pure iron, into two independent components is formally stated as:

Jan 1, 1967

By L. H. Schwartz, S. K. Lahiri, M. E. Fine, D. Chandra

WHILE the yield stress of solution treated Fe-Cu alloys increases rapidly with aging, a precipitate has only been directly observed in overaged samples.'-" This precipitate is essentially pure fcc copper, the E phase. Hornbogen2 suggested that the initial hardening is due to clustering of copper atoms in a bcc iron matrix. Hornbogen was not able to obtain direct confirmation for such bcc clusters by either X-ray diffraction or electron microscopy; however, he did observe analogous clustering in Fe-Au alloys7 where the scattering factor difference between iron and gold is more favorable than that for iron and copper. Fujii, Nemoto, Suto, and Monma4 recently observed diffuse electron diffraction scattering in a 2.5 pct Cu alloy aged at 500°C: for 30 hr. They suggested that part of the diffuse SCattering was due to a modulated structure of 26 to 42 wavelength parallel to the (110) matrix plane. This disappeared with further aging. However, 30 hr at 500°C is well beyond the peak strengthening in this alloy which occurred at less than I hr at 500oc.4 By transmission electron microscopy they could not distinguish between quenched samples and samples aged to maximum strength. The purpose of the present investigation was to try to obtain further confirming evidence for a precipitation stage preceding the formation of the fcc E phase. Change in Young's modulus was selected for study be- EXPERIMENTAL PROCEDURE The Fe-1.67 at. pct Cu alloy was supplied by the U.S. Steel Corporation in the form of a hot forged rectangular bar. The carbon and nitrogen contents of this alloy were 70 ppm and less than 10 ppm, respectively. The samples for Young's modulus measurements were made by cold swaging to & in. diam and cutting to 2 in. lengths. Tensile test samples 1 in. long were prepared by cold rolling to a thickness of 0.012 in. and then machining to gage dimensions of 0.5 by 0.012 in. For Mijssbauer studies, foils 1 mil thick were prepared by cold rolling. During fabrication the alloy was given intermediate anneals at 845OC followed by quenching. The specimens after preparation were solution treated at 1000°C (y field) or 845°C (a field) for 1 to 2 and 5 to 6 hr, respectively, in a dynamic vacuum of about 2 x lom6 torr. The tensile and modulus specimens were drop-quenched into iced brine through an aluminum foil which vacuum-sealed the bottom of the furnace tube. The MOssbauer foils were drop-quenched into helium gas cooled by passing through N2 (liq) in a copper coil. The grain diameter of the modulus and tensile specimens was between 0.025 and 0.035 mm. The samples were aged from 400" to 500°C in a dynamic vacuum of 2 x 10-6 torr and cooled by pulling into a water-cooled portion of the vacuum system. The dynamic Young's modulus was measured at room temperature using electrostatic excitation and detection of longitudinal vibrations.' Neglecting any length change during the aging, (this is expected to be comparatively small), the fractional change of Young's modulus (?Et)/Eav, is equal to twice the fractional change of the resonant frequency (?ft)/fav . ?ft =ft —fo where fo and ft are the resonant frequencies of a specimen before aging and after aging to time t. The measured f's, approximately 51,000 cps, were corrected to 25°C for any variation in the ambient temperature. The tensile tests reported were carried out at room temperature in an Instron with a 1000 lb full scale load cell. The flow stress reported herein corresponds to a strain of 0.002. The Massbauer spectra were taken in a constant acceleration model AM-1 NSEC spectrometer. The

Jan 1, 1970

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman. PERCY E. BARBOUR, Vice-Chairman. A. D. BEERS. Secretary, 55 Wall St., New York. N. Y. C. A. BOHN, Treasurer. Boston Meets first Monday of each winter month. C. C. EUSTIS, Chairman. R. L. AGASSIZ, Vice-Chairman. E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Boston, Mass. ALBERT SAUVEUR, H. L. SMYTH. Columbia Holds four sessions during year. Annual meeting in September or October. STANLY A. EASTON, Chairman. FREDERIC KEFFER, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2164, Spokane, Wash. C. LIVINGSTON. FRANK A. ROSS.

Jan 6, 1916

By H. E. Searle, Robert J. McKay, O. B. J. Fraser

The practical study of corrosion requires consideration of its economic aspects. It must be based on sound scientific principles, but it should be borne in mind that probably the most important object of a corrosion test is to determine what metal in corrosion-resisting construction will produce the greatest operating profit. Thus the corrosion test must be directly connected with money values or it is not a practical corrosion test. This, perhaps unusual, connection between corrosion and economics is partially due to the fact that corrosion deals only with the time factor or duration of equipment, and it is almost the only test which deals with this feature. In these statements a departure is made from the academic definition of the word corrosion and it is done deliberately. The use of the term corrosion is unusual. It is as though we spoke of a tensile test as a "breaking" test. We are not interested primarily in the break but in the strength of the metal. There is no English word which expresses our main interest in corrosion-testing, but let us have clearly in mind that we make corrosion tests to prevent corrosion. Our real interest is in this corrosion-prevention, not in the corrosion. Previous to 1922, it was common comment that "it is impossible to determine the course of corrosion by laboratory testing.'' This statement was true at that time in that the technique of laboratory testing for corrosion resistance was so vague that tests in the laboratory gave untrue results almost as often as true ones. This was so, even in the simple case of determining which one of two metals better resists a given solution. While this is no longer true the number of misleading "corrosion tests" still being ground out by laboratories is too large in the light of our present knowledge. There are two important features of corrosion testing whose neglect is a large contributing factor to misleading results: (1) The economic relations of the corrosion tests to other tests; (2) testing technique. Regarding economic relations J. F. Thompson l has said: "The use of any particular metal is rarely based upon the sole property of resistance to corrosion. In fact, I should like to venture the assertion

Jan 1, 1929

By Robert J. McKay, O. B. J. Fraser, H. E. Searle

The practical study of corrosion requires consideration of its economic aspects. It must be based on sound scientific principles, but it should be borne in mind that probably the most important object of a corrosion test is to determine what metal in corrosion-resisting construction will produce the greatest operating profit. Thus the corrosion test must be directly connected with money values or it is not a practical corrosion test. This, perhaps unusual, connection between corrosion and economics is partially due to the fact that corrosion deals only with the time factor or duration of equipment, and it is almost the only test which deals with this feature. In these statements a departure is made from the academic definition of the word corrosion and it is done deliberately. The use of the term corrosion is unusual. It is as though we spoke of a tensile test as a "breaking" test. We are not interested primarily in the break but in the strength of the metal. There is no English word which expresses our main interest in corrosion-testing, but let us have clearly in mind that we make corrosion tests to prevent corrosion. Our real interest is in this corrosion-prevention, not in the corrosion. Previous to 1922, it was common comment that "it is impossible to determine the course of corrosion by laboratory testing.'' This statement was true at that time in that the technique of laboratory testing for corrosion resistance was so vague that tests in the laboratory gave untrue results almost as often as true ones. This was so, even in the simple case of determining which one of two metals better resists a given solution. While this is no longer true the number of misleading "corrosion tests" still being ground out by laboratories is too large in the light of our present knowledge. There are two important features of corrosion testing whose neglect is a large contributing factor to misleading results: (1) The economic relations of the corrosion tests to other tests; (2) testing technique. Regarding economic relations J. F. Thompson l has said: "The use of any particular metal is rarely based upon the sole property of resistance to corrosion. In fact, I should like to venture the assertion

Jan 1, 1929

By C. A. Heiland W. E. Pugh

The principle underlying the majority of magnetic intensity variometers is a comparison of the force to be measured with another force of known magnitude. The known force may be (a) of a magnetic nature, such as magnetic fields produced by magnets or coils, or (b) of a mechanical nature, such as (1) the elastic forces of wires, or (2) the force of gravity, such as employed in bifilar magnetometers and magnetic balances. In instruments of such type, usually a magnetic system is employed, free to move about either a horizontal or vertical axis, on some sort of a suspension. If the earth's magnetic field alone were present, such a system would adjust itself into the direction of the field or that of its components. Owing to the simultaneous action of the comparison force, however, the magnetic needle assumes a position that differs from the direction of the magnetic force; for all such instruments, the angle of deflection is given by tan = FIX, where F is the known and X the unknown earth magnetic force component. In other words, the magnetic system merely serves as an "indicator" for the position of balance of the two forces. Considering the matter from this point of view, it is not immediately obvious why the temperature of such a magnetic system should modify the results. In magnetic instruments, we may distinguish two different effects of temperature: (1) a magnetic effect and (2) a mechanical effect. The first is due to the fact that the magnetic moment of a magnet drops with an increase in temperature. This drop is characterized by the temperature coefficient of the magnetic moment (see equation 1). The second effect is due to the change in the torsion of suspension wires with temperature or to the expansion of lever arms of masses acting on magnetic balances.

Jan 1, 1934