Search Documents

By H. H. Stoek

The fundamental reasons underlying the choicc of a method of mining a coal seam are safety of operation, cheapness of producing the coal and the character of the product as a saleable article. From the standpoint of safety, open or strip coal mining is always preferable, as many of the dangers inherent to underground work are absent, such as explosions of gas and dust, falls of roof and coal, and also to a great extent those due to haulage and the use of explosives, thus eliminating three of the chief causes of accident from which about 75 per cent. of the underground accidents in coal mines occur. The conditions under which coal is stripped also make the work much safer than ordinary quarry work, as the depth of the pit is usually comparatively small. Prom the standpoint of low mining cost, there is much misapprehension and many of the costs given are misleading in that they do not take into account such items as the destruction of the surface for future use, the full cost of the removal of the overburden, depreciation, amortization, coal depletion, loss of time through floods and from bad weather in winter, etc. Coal is no doubt often put on the cars at less cost by stripping than by underground mining, but by no means always so, as is too generally assumed. In some cases coal must be obtained by stripping or not at all, because the small amount of overburden renders underground mining impossible.

Jan 1, 1918

By L. N. Brown

The use of sheet and strip metal has increascd rapidly during the last few years and manufacturers have been called upon for an ever-increasing tonnage, better drawing quality, and better surface. The automobile industry is probably the most insistent in striving for a better product and a desire to reduce costs. Confronted by these demands, the mills have directed their efforts toward the delivery of material. Their personnel has been occupied largely with the problems incident to production, as any increase forced the use of new sources of raw material with their problems. These problems, combined with those met in the daily routine, have demanded immediate attention, with the result that the standardizing of heat treatments, quality, or temper, etc., have been neglected. Considerable work in standardizing has been done by many companies, but no acceptable method has been developed. The following method, therefore, is given with the hope that some method that can be accepted by the manufacturers and users may be developed. The problem of selecting a material with such properties that the losses in processing are a minimum is interesting and difficult. A description of the properties required is likewise difficult, largely because of loose terms. Another handicap is the number of methods of testing which have not been standardized and concerning which little information is available. In the selection of drawing or forming stock, it is advisable to eliminate as many variables as possible; consequently the method of testing the material is of the utmost importance. The method should be rapid and comparatively easy of application, as it is more important that a large percentage of the stock be tested with reasonable accuracy than that

Jan 1, 1923

By L. N. Brown

The use of sheet and strip metal has increascd rapidly during the last few years and manufacturers have been called upon for an ever-increasing tonnage, better drawing quality, and better surface. The automobile industry is probably the most insistent in striving for a better product and a desire to reduce costs. Confronted by these demands, the mills have directed their efforts toward the delivery of material. Their personnel has been occupied largely with the problems incident to production, as any increase forced the use of new sources of raw material with their problems. These problems, combined with those met in the daily routine, have demanded immediate attention, with the result that the standardizing of heat treatments, quality, or temper, etc., have been neglected. Considerable work in standardizing has been done by many companies, but no acceptable method has been developed. The following method, therefore, is given with the hope that some method that can be accepted by the manufacturers and users may be developed. The problem of selecting a material with such properties that the losses in processing are a minimum is interesting and difficult. A description of the properties required is likewise difficult, largely because of loose terms. Another handicap is the number of methods of testing which have not been standardized and concerning which little information is available. In the selection of drawing or forming stock, it is advisable to eliminate as many variables as possible; consequently the method of testing the material is of the utmost importance. The method should be rapid and comparatively easy of application, as it is more important that a large percentage of the stock be tested with reasonable accuracy than that

Jan 1, 1923

By William D. Klopp

A study was conducted of the tensile and creep properties of are-melted and electron-beam-melted tungsten over the temperature range 2250° to 4140°F. The tensile and creep strengths vary with pain size, the finer -grained materials being stronger. The activation energy for transient creep at 2250° to 3500°F is 95,000 cal per (g)(mole), while that for steady creep at 3300o to 4000°F is 141,000 cal per (g)(mole). At 2875o to 3300°F the apparent activation energy for steady creep decreased with decreasing temperature. It is suggested that cross slip is rate controlling during transient creep, while dislocation climb is rate controlling during steady creep above 3300° F. ALTHOUGH considerable data have been generated on the high-temperature tensile properties of powder-metallurgy tungsten,1 relative few data have been published on the properties of are-melted2 or electron-beam melted tungsten.3 Furthermore, the available data show a fairly large amount of scatter at high temperatures. The effects of structure and purity have not yet been defined, aside from observations that high-purity electron-beam (EB)-melted tungsten3 and single-crystal-plasma-flame tungsten4 are weaker than less pure powder-metallurgy tungsten. The creep behavior of powder-metallurgy tungsten has been studied, but no data are available on the creep behavior of tungsten consolidated by melting. Green5 found that powder-metallurgy tungsten exhibited linear creep at 4082° to 5072°F with an activation energy of 160,000 cal per (g) (mole). The similarity of this activation energy to that of 153,000 cal per (g)(mole) for volume self-diffusion6 suggests that recovery of strain hardening by dislocation climb is rate controlling in this temperature range. In studies at 4800°F, Sutherland and Klopp7 concluded that grain size significantly affected the creep behavior of commercial powder-metallurgy materials. This grain-size effect was suggested by sherby,8 although the opposite relation had been reported for aluminum.' The purpose of the present study was twofold: first, to provide baseline data on high-temperature tensile and creep properties of are-melted and EB-melted tungsten for concurrent tungsten alloy studies, and, second, to determine the phenomenolo-gical effects of structural and purity variables on the high - temperature mechanical properties of tungsten. EXPERIMENTAL The are-melted tungsten materials were prepared by melting sintered 1-1/4-in.-diam electrodes into 2-1/2-in.-diam by 5-in.-long ingots. The are-melting facility has been described previously.' Eight ingots were melted, machined, and hot-extruded at

Jan 1, 1965

By E. T. Knight, John D. Gill

IN ITS capacity for service to the public the oil industry is truly gargantuan. But it is only in this respect that the industry is the voracious, many-headed, many-armed and many-handed creature it has been so often painted by those who know it not too intimately and only from the outside. Contrasted sharply with the immensity of the service rendered is the relatively modest share of the national income which has gone to those who provided the tools and the mental and manual labor with which the service was performed. No doubt the relative meagreness of the re- ward was the result of a combination of fortuitous circumstances respecting the nature and accessibility of the industry's raw material and the extensive development and application of the most advanced technology, spurred by an intense competition.

Jan 1, 1940

By Harold F. Unger, Byron S. Snowden, William H. Engelmann

The effects of using surfactant solutions while diamond drilling in amygdaloidal basalt of the Upper Michigan copper mining district were investigated. Nonionic, anionic, and cationic surfactant solutions, all biodegradable, were tested with size AX surface-set bits mounted on a drill instrumented for continuous recording of thrust, rotational speed, and torque levels. Water flow and penetrations rates were also recorded. A drilling study was carried out, testing two rotational speed levels, two diamond bit grade levels, and four flushing agents (including water as a control). Comparison of all low-speed/high-thrust groups of tests shows that the non-ionic surfactant produced a 35% overall average increase in penetration rate over water, the anionic a 29% increase, and the cationic a 28% increase. These increases in, penetration rates resulted in a 22 to 26% reduction in cost over flushing with water alone. With the high-speed/low-thrust combination, the surfactants produced less benefits in penetration rate increases over water (14% increase for nonionic, 14% decrease for anionic, and 2% decrease for cationic type). Particle size analyses were run on drill cuttings produced by the three surfactant solutions and by water. All surfactant solutions showed a 20 to 50% increase in solids content over that of water alone. Since flushing rates were constant, these increases in solids content agree well with the penetration rate changes. The diamonds were recovered from each bit by matrix dissolution, and bit wear was measured in terms of total loss of weight. Flushing with surfactant solutions showed a savings in bit wear in most cases. The drill team noted also that surfactant flushing improved recovery of drill core by allowing easier removal of the core from the barrel.

Jan 1, 1976

By Jack L. Taylor

WITH the exception of the work of Vogel,&apos; and Rolla and Iandelli, very little information has appeared in the literature on titanium binary systems with the rare earth elements. Rare-earth additions to titanium alloys may possibly parallel the beneficial effects on the physical properties of certain steels. Having this in mind, some knowledge of solubility limits and intermediate phases, if any, would be useful. An investigation of the titanium-rich Ti-Ce system was started. Alloy Preparation The iodide titanium from the New Jersey Zinc Co. and the cerium metal from the Institute for Atomic Research Ames Laboratory used in this work were supplied with the typical analysis shown —iodide titanium: 0.0065 pct Mn, 0.0022 pct Fe, 0.0015 pct Cu, and 0.0042 pct Pb; cerium metal: <0.01 pct Fe, <0.03 pct Si, <0.05 pct Ta, <0.02 pct Pr, <0.03 pct Ca, <0.02 pct Mg, with no trace of Nd, La, or Th. The cerium metal, stored in oil, was washed and scraped just before weighing into capped cups machined from iodide titanium. The cold hearth helium-arc furnace described by Schramm et al3 was used for melting. The alloy buttons from the arc-melted cup were cut in two, mounted, and examined. Homogeneous alloys were demounted and rolled to approximately 1/4-in.sq bars. Sections l/8 in. thick were cut from the bar to provide samples. The Ti-Ce alloy buttons analyzed for cerium were of the following composition: 0.19, 0.36, 0.48, 0.61, 1.15, 2.52, 3.06, 3.70, 4.30, 9.20, 14.26, and 18.50 wt pct. Nominal

Jan 1, 1958

By William B. Plank

RECENT interest in the character of employment of young mining engineering graduates has been stimulated by my studies, during the past ten years, of student enrollment and employment of graduates of the mineral technology schools of the United States and Canada. Enrollment data in the following article are taken from these studies and information about the kind of work engaged in by mining engineers is assembled from my professional experience, sixteen years of which have been as professor of mining engineering.

Jan 1, 1938

By Frank Clemes Smith

The study of the so-called refractory gold-ores of the Potsdam sandstone, ores which are probably of wider occurrence and of much greater economic importance in the Black Hills than is generally supposed, has led the writer to formulate in the present paper some of the results obtained in the course of a special examination of these particular ores, conducted at the State School of Mines at Rapid City, So. Dak. Various circumstances have interrupted the work, and it will easily be seen that relatively little has yet been accomplished; but it is hoped that this little may be of sufficient interest to justify a later supplement. Tellurium, discovered by Muller von Reichenstein in 1781, is generally classed as a very rare metal; it is further mentioned by one of our late writers as " of comparatively little importance," and as obtained from its ores by a " complicated process.&apos;&apos; Concerning its rarity, we have some trustworthy evidence below. Its commercial importance, particularly in connection with electrical appliances, has been passed upon by Mr. Edison ; * and it is certain that, in some metallurgical processes for the treatment of gold- and silver-ores, it may be saved as a byproduct at a relatively reasonable expense. The importance of tellurium as a mineralizing agent is emphasized by the remarks of one of our leading metallurgists,jwho, in his own practice and by a wide series of experiments, has found its occurrence to be much more general than has been supposed. Recently the same writer has discussed the occurrence of tellurides and oxidized tellurium compounds in the gold-ores of Cripple Creek, Colo., and in those of the Black

Jan 1, 1897

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

Dispersion-containing titanium-copper alloys were prepared having mean free paths varying from 1.0 to 9.7 P. Tensile studies at room temperature and at 1000°F showed that little or no strengthening occurred when the mean free path exceeded 3 p. However, at lower values of mean free path appreczable strengthening was observed. A considerable amount of strengthening also resulted from copper in solid solution. DURING the past several years, an increasing amount of study has been devoted to dispersion hardening, an alloying process in which increased strength is obtained through the addition of a ran-

Jan 1, 1961

By W. E. Forsythe

WHEN measuring ordinary temperatures, the instrument is generally placed in very close contact with the body the temperature of which is desired. However, if the temperature of the source is continually raised, a point is soon reached where no known substance will, in general, remain constant in any of its temperature-measuring properties if placed in direct contact with the source. Also, it is occasionally necessary to measure the temperature of a source that &apos;is so small or so situated that it would be very hard to bring the measuring instrument into direct contact with the source. When these conditions exist, advantage is taken of the well-known fact that all bodies, when at sufficiently high temperatures, send out radiation in amounts readily measurable. This radiation has been found to be related to the temperature. The temperatures of very hot bodies have probably always been judged by the color, or the brightness, of the light given off. With practice, one can estimate probably within 50° to 100° C. of the correct value. However, if judgment is left to the eye alone, very much larger errors are sometimes made, due to

Jan 9, 1919

By M. C. Dow

INTRODUCTION BELT conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stonecrushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. GENERAL RELIABILITY It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 1/2 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. LOADING THE BELT It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined conveyor to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1947

By Norman Carmichael, John Kiddie

The problem of transportation in the Clifton-Morenci district of Arizona has been one of peculiar difficulty and consequently has been an important factor in the cost of mining and treating the ores produced. From the crude beginning made over 50 years ago, many changes have been necessary to keep pace with the increased output of copper. A heavy-duty haulage system has developed on the original 20-in. track gage to meet the existent metal-mine conditions. Topography The transportation difficulties of this district may be readily appreciated from the relief map shown in Fig. 1. The northern half of the district is high mountainous country and there is a general but irregular drop toward the southern part, where the country, although still rugged, is in reality a great sloping plain. This is cut by numerous ravines from which the waters, in the rainy season, discharge into the channel of the San Francisco River. A chasm, 1000 ft. deep, has been eroded through the center of the district by Chase Creek, which is flanked by high irregular mountain masses, notably Copper Mountain, American Mountain, Coronado Mountain, and Markeen Mountain. The latter rises 2300 ft. above the bed of the creek, The San Francisco River has also cut a deep channel, though it is somewhat broader than Chase Creek. Eagle Creek traverses the extreme southwest portion of the area, where it has carved picturesquely through vast volcanic flows. Faulting has left its mark upon the topography of the district by adding to the irregularities caused by erosion. Strong faults occur at the Coro-

Jan 1, 1924

By Galen G. Waddell

Several years of rock-burst research conducted by the U.S. Bureau of Mines in cooperation with the mining companies of the Coeur d&apos;Alene mining district, Idaho, in addition to progress made by others throughout the world, have led to a good understanding of the rock-burst problem. This paper describes conditions which have caused specific bursts, present capabilities of detecting stress buildup and bursts, control methods, and a suggested approach to analyzing any individual mine-burst problem. A rock burst is the sudden, violent release of stored strain energy in rock by some mechanism of rock failure, generally accompanied by expulsion of rock with consequent damage to the mine. A burst may be audible for only a few hundred feet, or on the surface it may sound like a sonic boom miles away. A Dictionary of Mining, Mineral, and Related Terms, U.S. Bureau of Mines (USBM)* 1968yand defines a burst as Bureau "That phenomenon which occurs when a volume of rock is strained beyond the elastic limit and the accompanying failure is of such a nature that accumulated energy

Jan 1, 1971

By Sidney Diamond, Charles Wert

The anelastic behavior of Ni-C alloys of nominal 0.5 wt pct C has been determined over a wide temperature range. The most prominent damping effect, that due to the presence of C-C pairs, was measured both above and below the Curie temperature. The effect on diffusion of the C-C pairs by magnetic spin ordering is deduced to be very small. The diffusion coefficient for C-C pairs in nickel is given by the expression ThE solid-state diffusion of both interstitial and sub-stitutional solutes in ferromagnetic solvents has been the subject of a number of investigations. Measurements of the self-diffusion of iron,"&apos; the diffusion of nickel1,4 gold,"1 and cobalt4 into iron, the diffusion of vanadium in an Fe-V alloy,&apos; and the diffusion of cobalt and nickel in Co-Ni alloys9 show an unusual behavior. In both the ferromagnetic and paramagnetic regions, far removed from the Curie temperature, the diffusion coefficient, D, obeys an Arrhenius relation. However, in the ferromagnetic region D is markedly lower than would be expected from an extrapolation of D from the paramagnetic region; this results in an increase in the activation energy in the ferromagnetic region. The cause of this effect for self- and substitutional diffusion is uncertain. Since substitutional diffusion is presumed to proceed by the vacancy mechanism, it has been variously suggested that the increase in activation energy below the Curie temperature is due to one of the following causes: 1) an increase in the energy of formation of a vacancy because of local demagnetization around the vacancy,2,3 2) a decrease in vacancy mobility in the ferromagnetic state,&apos; or 3) an effect on the entropy of motion of a vacancy in the ferromagnetic state.5 Quite another explanation for the observed effect has been proposed by Borg.7 The diffusion coefficient is a function of the elastic constants of a metal. Since the temperature dependence of the elastic constants often changes at the Curie temperature, the temperature dependence of D might be expected to undergo a universal change in the vicinity of the Curie temperature. The magnitude of the change in D would, of course, depend on the magnitude of the change in the elastic constants. One might attempt to differentiate between vacancy effects and elastic effects by making measurements on interstitial alloys, in which vacancy effects play no role. Some measurements of this type have been made; this paper reports additional observations. Measurements of the diffusion of carbon in a Fe by a tracer technique8 and of the diffusion of carbon in a Co and in Co-Fe alloys by a decarburization method9 reveal a small effect, if any, on D of the magnetic change at the Curie temperature. If the effect of spin ordering is only to alter the parameters controlling formation or mobility of a vacancy, interstitial diffusion should indeed remain unchanged through the magnetic transition, as these measurements imply.

Jan 1, 1968

By Bruce A. Kennedy

The place of the young engineer in the mining industry has been the subject of a large number of keynote addresses, magazine articles, and papers in the past year. One of the best of these was the keynote address given by Mr. J. C. Kinnear, Jr. at the Fifth Annual Intermountain Minerals Conference in Vail. Colorado. Mr. Kinnear presented as part of his address the statistics of a Canadian survey Instigated to find out why young engineers and geologists are leaving the mining industry. The results of the survey showed four main reasons for leaving: 1) insufficient money 2) slow promotion 3) lack of association with senior engineers, as well as insufficient opportunity to keep abreast of technological development 4) geographic isolation

Jan 1, 1970

By W. C. Hardy, B. W. McArthur

The purpose of this work is to show application of laboratory data in calculating solution gas-drive performance of the Cisco K-I reservoir. Included herein is a diagram showing the graphical relationship between six variables common to all solution gas-drive mechanisms. With an iterative process one may assume existence of any of these six variables at a particular pressure and calculate the production performance likely to occur in a reservoir produced by solution gas drive. Four unique pressure values are described at which the material balance equation alone is sufficient to predict the cumulative volumes of gas produced. Information derived from these pressure points establishes a criterion for determining compatibility of the pressure-volume-temperature (PVT) analysis of the produced crude with the gas production history. Two averaging procedures are used to arrive at a relative permeability-saturation relationship which describes the field-wide performance. INTRODUCTION The Cisco K-1 reservoir is a lenticular-type sand structure lying at approximately 6,300-ft subsurface. It is located in the H. and T. C. Railroad Co. Block 97, SW 1/4 S 392 and NW 1/4 S 385, Scurry County, Tex. Correlation of data from logs indicated that the Cisco K-1 reservoir occupied approximately 3,218 acre-ft of space with a closure of from 15 to 20 ft. Analysis of the production data indicates that the initial formation pressure and temperature were 2,450 psig and 121°F, respectively. The bubble point occurred at 1,715 psig after production of 12,256 STB oil and 11,520 Mcf gas. Only traces of water have been produced since initiation of production. Successive material balance calculations from June, 1952, to June, 1957, showed that no initial gas cap or water influx has contributed to production of oil and that the Cisco K-1 reservoir originally contained approximately 1.44 X 10" STB of oil. THEORY Methods for calculating solution gas-drive perform-

By N. A. Stockett

SOUTHEAST Missouri is the largest and oldest lead-producing district in the United States. For the year 1941, the statistical picture of pig-lead production, stated in short tons (partly estimated by the Engineering and Mining Journal) is as follows. [Tons World production 2,000,000 United States production 460.000 Southeast Missouri production 242,000] The consumption of primary lead in the United States in 1941 was approximately 900,000 tons, or almost double the country&apos;s production. The largest previous year&apos;s consumption in the United States was 718,000 tons, in 1926. The largest quantities of lead are used for cable sheathing, storage batteries and white lead. During 1941 tetraethyl lead for auto and aviation gasoline consumed 50,000 tons of lead. The entire lead production of Southeast Missouri is now mined by the St. Joseph Lead Co., whose dominant position as the largest producer in the United States of lead directly from ores is best shown by the fact that in 1941 it produced approximately 31 per cent of the lead production of the United States from its mines in southeast Missouri, where 22,000 tons of ore, averag¬ing over 3.00 per cent lead, is mined per working day. It is known that lead was mined at Mine La Motte, Madison County, Missouri, by Renault in 1723. Other white men and Indians probably did some mining prior to that time. Since 1865, the recorded production to Jan. 1, 1942, shows that the St. Joseph Lead Co. and the various other companies that have operated in St. Francois County mined lead ore, which, after milling and smelting losses produced 5,00,000 short tons of pig lead. About 95 per cent of the present lead production of Southeast Missouri is mined in St. Francois County. The northern part of this area is 60 miles south of St. Louis. The remainder of the lead is obtained at Mine La Motte, about 25 miles southeast from the center of the producing area in St. Francois County. PROSPECTING In this district, most of the ore is discovered by surface and underground diamond drills and by prospect drilling underground with rock drills. Each 2-ft. length of the cuttings from these Jackhamer prospect holes is assayed for lead. These holes are marked and the records are entered on maps. It has been found that close drilling--100-ft. centers of holes, and sometimes less-is necessary in order to locate most of the smaller commercial ore bodies, many of which previously had been missed by drilling the areas with holes spaced 200-ft. centers or more.

Jan 1, 1943

By H. M. Ziesemer

PRIOR to 1909 that mountain of porphyry, known as. Sacramento Hill, had remained hardly touched but had always aroused suspicions as to the presence of ore within.. During that year, exploratory work was started by underground methods; drifting and raising continued until 1913. It was proved that a mineralized zone existed, the limits of which had not been determined; so, because of the lower costs of exploratory work and the greater desirability of vertical sections, it was decided to prove the extent of the ore zone by churn drills. Drilling continued until the year 1917, when it seemed almost certain that the horizontal limits of the orebodies had been determined. Ore continued in depth in one direction beyond a point where it was economical to explore by churn drilling; this extension is still being developed by underground methods. The irregularities of the boundaries of the ore zones, together with the variable grades of ore encountered, made it necessary to drill on the corners of 100-ft. squares. Two ore zones were proved, known as the East and West Orebodies. The Sacramento Hill porphyry stock intruded into the Dividend fault. The fault ran roughly east and west with a dip to the south, having pre-Cambrian schists on the north against Paleozoic limestone on, the south. This intrusion was accompanied by a silica breccia on the south periphery, along the limestone contact side. The ore lay in the silica breccia and in the porphyry, some distance from the breccia. No ore was found in the heart of the porphyry mass on the north side, along the schist contact. The West Orebody is elliptic in shape, having a major axis of 1200 ft. (366 m.) and a minor axis of 800 ft. (244 m.); these diminish with depth until, at 300. ft., the axes are 500 ft. and 300 ft., respectively. The ore consists of chalcocite, some bornite, chalcopyrite, and considerable pyrite in a silicious gangue. About 30 per cent. of the copper is caused by

Jan 2, 1922

By Thomas B. Douglas

INSTRUMENTATION in the process industries can no longer be regarded as a convenience, but rather an absolute necessity. Although many chemical processes must already be conducted with instruments, every properly designed application of automatic process control will improve operation: 1) the product will be more uniform and of higher quality; 2) the manual labor saved will reduce cost; 3) uniformity of flow and uniform control of process will increase production; and 4) surges will be eliminated, making it possible to operate equipment near ultimate capacity at all times. Industrial instruments fall into two general classifications—those that measure and those that measure and control. The cement industry has been using instruments for a number of years, particularly in the burning process, primarily for indicatlng and recording. Automatic process control makes additional use of these instruments, and others, to control variables. Assisted by the instrument manufacturers, engineers at Ideal Cement Co. achieved considerable progress in determining how well the usual recording instruments could be made to control various phases of cement-making. The results of these experiments were used to make the new plant at Houston as wholly automatic as possible. The original Houston plant, built in 1937 by Gulf Portland Cement Co., consisted of only one 8 x 220-ft kiln and the necessary grinding mills and accessory equipment and had a capacity of 900 bbl per day (300,000 bbl annually). Ideal Cement Co. purchased this plant in 1940 and almost immediately started plans to increase its production. In 1941 a 9 x 220-ft kiln was installed and grinding and storage capacity were increased. The growing demand for cement in the Houston area necessitated a third kiln (9 ft 6 in. x 250 ft) in 1947. This brought the plant up to its present capacity of about 1.3 million bbl per year. Calcium silicates in cement are produced in a burning operation at high temperatures from raw mix of argillaceous and calcareous materials that have been crushed, mixed, and ground to a fine powder. The composition of this mixture must be kept consistent within narrow limits. Raw mixing and grinding may be done either wet or dry, but in both instances the materials must be correctly proportioned, finely ground, and thoroughly intermixed before entering the kiln. As the raw mix passes through a long horizontal rotary

Jan 1, 1959