Search Documents

By Alfred H. Bell

The upswing in oil production and drilling activity in Illinois that began in 1937 gained momentum in 1938 and promises to bring a new and higher peak in the state's annual production in 1939. In 1938 the production totaled 23,929,000 bbl., as compared with 7,426,000 bbl. in 1937, more than a threefold increase. The number of producing oil wells in the new fields was 230 at the end of 1937 and it increased to 2157 at the end of 1938. Daily production for the whole state increased from approximately 35,000 bbl. at the end of 1937 to approximately 135,000 bbl. at the end of 1938, nearly a fourfold increase. Of a total of 2539 wells completed in 1938 in Illinois, 1984 produced oil, 26 produced gas and 529 were dry holes. Of the total, 377 are classified as "wildcat" wells, defined as wells drilled outside of proved territory and more than one mile from the nearest production. The remainder, 2162 wells, were drilled in or near proved fields. Of the 377 wildcat wells (Table 2) 32 were successful in discovering oil or gas in commercial quantities, either new fields or extensions of old fields. Four of these discovery wells mere gas wells, which are not yet commercially productive owing to lack of pipe-line facilities. A special effort was made to ascertain the reasons for the locations of as many as possible of the wildcat wells and the results of this investigation are set forth in the following table:

Jan 1, 1939

By J. C. Holm

ALTHOUGH the main constituents of Portland cement are the oxides of calcium, silicon, aluminum, and iron, characteristics of the cement are seriously affected by such contaminants in the raw materials as magnesium, phosphorus, sodium, potassium, sulfur, and others of lesser importance. Sources of cement raw materials comprise a long list of minerals occurring in nature in various degrees of purity. The calcareous raw materials are generally limestone of purity varying from calcite to cement rock (a low-grade limestone of natural, almost correct chemical composition), chalk, marl, seashells, coral, and coral sand. The argillaceous raw materials supplying silicon, aluminum, and iron are mainly various forms of clay and shale, to which may be added silicious sand, iron ore, bauxite, or kaolin for minor adjustment of the chemical composition. The quality of Portland cement in this country, as in most parts of the world, is controlled by rigid specifications limiting both its chemical and physical characteristics, and cement manufacturers must comply with these specifications to market their products. Brandon Raw Materials: An unusual deposit of marl, limestone, and clay occurs 12 miles east of Jackson, Miss., near the village of Brandon. The deposit is of sedimentary origin and of relatively young geological age. Layers of marl vary from putty-like consistency to such hardness that it can be cut with a knife. Interspersed between the layers of marl are bands of limestone varying from very soft to hard. the compressive strength of the hardest layers exceeding 15,000 lb per sq in. The layers of marl range in thickness from a few inches to about 25 ft. The limestone bands seldom exceed 2 to 3 ft but often occur in thinner veins in the quarry face. Above the top layer of the deposit, which may be marl or limestone, a layer of clay ranges in thickness from a few inches to more than 20 ft. Part of this clay is harvested with the raw material to supply part of the argillaceous components, but most of it is stripped as overburden and wasted. A highly silicious clay of extreme fineness, harvested from the bottom of the quarry below the marl and limestone bands, is to correct the silica content. Fig. 1 shows typical examples of the interrelation of the various materials, based on drill logs obtained during exploration of the deposit. The marls vary in moisture content in the bank from 15 to 30 pct and contain up to 70 pct -200 mesh particles and up to 40 pct —10 p particles. A large percentage of the fine fraction is within the colloidal range, making the marl extremely sticky. The limestone beds range in hardness from that of the hardest marl to a medium hard limestone and in moisture content from 2 pct to approximately 14 pct. The line of demarcation is often difficult to draw and the moisture content is possibly the best means of classification. The ratio of soft to hard material is not constant throughout the deposit, but the average is approximately 70 pct soft to 30 pct hard material. Through the years this deposit had been repeatedly explored by cement companies and rejected as unsuitable for cement manufacture, mainly because of physical characteristics. In 1950, after careful exploration of the deposit and comprehensive laboratory and pilot plant tests of the raw materials, officials of Marquette Cement Mfg. Co. of Chicago were convinced that a practical and economical method of processing the raw materials had been devised and authorized construction of a new plant that began production in December 1951. Marl and limestone, common raw materials for Portland cement, usually occur in such a manner that they can be worked separately. Their harvesting and processing normally have presented no difficult problems, as standard equipment and methods are available for handling either sticky or hard materials. No other cement plant utilizes a deposit of the nature of that at Brandon, however, and for this reason no prior art was available for design. When properly blended, the raw materials produced an excellent cement without additives. Basic problems to be solved in designing the cement plant were:

Jan 1, 1957

By E. H. Rennhack

Phase equilibria of the zinc-rich portion of the Zn-Fe-A1 system containing up to 20.0 wt pct Fe and Al have been investigated at 600°C (1112°F), 450°C (842°F), and room temperature by metallographic and X-ray diffraction techniques. The phase relationships were found to involve only those phases present in the three binary systems. THE presence of small quantities of aluminum (approx. 0.2 wt pct*) in zinc galvanizing baths is known to suppress the formation of Zn-Fe alloy layers within the coating.' As part of an extended investigation of this suppression effect and the alloy reactions involved, the zinc-rich corner of the Zn-Fe-A1 equilibrium system containing up to 20.0 pct Fe and Al was determined at 600°C (1112°F), 450° F (842° F), and room temperature. The present paper reports the findings of this study. The constitution of the Zn-Fe system has been reported by Raynor2 based mainly on the work of Schramm3-3 and Truesdale et a1.6 The solid solubility of iron in zinc is extremely small and lies between 0.0009 and 0.0028 pct in the range 150° to 400°C (302°to752°F). Within the temperature and composition range of interest, a eutectic reaction involving nearly pure zinc, liquid = Zn+FeZn13, is observed at about 419°C (786° F) and 0.018 pct Fe along with a peritectic reaction, FeZn7+ liquid e FeZn13, at 530°C (986° F) and 6.2 pct Fe. The latter reaction is sluggish due to the large proportipn of solid phase involved in the transformation. Halla et al.,7 identified the compound FeZn13 as monoclinic with a = 13.68, b = 7.63, c = 5.07, and B = 128°44'. The structure of FeZn7 was reported by Bablik, et al.,8 to be of hexagonal symmetry, belonging to either the C6v = C6/m mc or D46h = C6/mc space group. Divensions of the unit cell are a = 12.81A and c = 57.6a. The Zn-A1 diagram as composed by Raynor9 and later Gebhardt10 is characterized by a eutectic decomposition, liquid 382°C (720°F) and 95.0 pct Zn and a eutectoid decomposition, at 275° (527°F) and 78.0 pct Zn. The eutectoid reaction cannot be suppressed permanently by quenching. Above 275° (527° F), a and a' co-exist in a closed miscibility gap between 31.6 and 78.0 pct Zn. Both phases are fcc and have nearly the same lattice parameter. The maximum solubility of aluminum in zinc (B) is approximately 1.0 pct at the eutectic temperature. PROCEDURE Materials. The experimental alloys were prepared from both massive and powdered material. Cast alloys were composed from three zinc-base master alloys containing 8.0 pct Fe, 16.0 pct Fe, and 50.0 pct Al which were made from C.P. zinc, Armco iron, and

Jan 1, 1962

By Philip B. Bucky

[ ] FOREWORD THIS symposium brings together points of view, experiences and ideas on rock bursts from a goodly portion of the globe. Some conceptions, particularly those regarding the necessity of depth, have been fairly well shattered, as we find that they are present in the water tunnels of New York, on the surface at marble quarries in Vermont, and in the coal mines of the United States, as well as in the deep mines of the South African and Kolar gold fields, and in the nickel, copper and gold mines of Canada. Their occurrence under such a variety of conditions is, therefore, a challenge,

Jan 1, 1942

By AIME AIME

THE annual session for the election of officers and transaction of other official business of the Institute, which must be held, in accordance with the By-Laws, in New York on the third Tuesday in February, was the only session scheduled for the morning of Feb. 19. Many members gathered in the auditorium at 10 o'clock, and President George Otis Smith presided. He said that his report was best set forth in the reports of the other officers and committees, which were avail-able in printed form. Productive activity had characterized the Institute's year and a number of new ventures had been successful. He felt that he had "rattled around" in the office of president, as he had traveled some 39,000 miles during the year in visiting the various Sections, having visited everyone that had held a meeting during his term of office. He spoke of the educational effect on a president of these broad contacts and suggested that a three-year course would be even more enlightening than one.

Jan 1, 1929

By G. P. Marino

The "conductivity ", Kr, of a spherical void in a linear temperature gradient due to radiation is calculated by integration of the general expression for diffuse radiation between two gray surfaces of arbitrary orientation. The spherical geometry allows an exact evaluation of the phenomenon without resorting to up-proximate expressions for the radiant heat flux. The resulting expression for Kr is three quarters of the approximate value obtained by Loeb. IN the determination of the thermal conductivity of porous materials such as sintered UO2 and ThO2 fuel pellets, the magnitude of the thermal conductivity in the pores due to radiative heat transfer across the pore, Kr, may be important in assessing the total conductivity of the pellets. Loeb' has calculated Kr for various pore geometries by approximating the net flux of heat between two surfaces of temperature difference AT as 4eT~AT and obtained: K,=4yoet3odp [1] where a is the Stefan-Boltzmann constant, E is the emissivity of the radiating surface, To is the average absolute temperature of the region across which radiation occurs, dp is the largest dimension of the gap in the direction of heat flow, and y is a geometric factor. That is: y = 1 for laminar pores and cylindrical pores with axes parallel to the heat flow direction, y = 2/3 for spherical pores, y = /4 for cylindrical pores with axes perpendicular to heat flow direction. It was the purpose of this work to obtain an exact expression for K, in spherical pores by integration of the general expression for the net heat transfer between two incremental areas on the surface of a spherical pore. This procedure yields a value of Kr 3/4 of that obtained by Loeb. I) CALCULATION OF Kr Fig. 1 illustrates the general geometry which defines the problem. The total emissive power for a gray body is given by: E = EoT4 [2] where E is the radiated energy per unit area of the radiation surface per unit time, T is the absolute temperature, o is the Stefan-Boltzmann constant (o = 5.67 X lo- '' watt per sq cm-"K1), and E is the emissivity of the surface. Although Eq. [2] gives the exact expression for the total emissive power of any gray body, all practical problems involve the net exchange of thermal radiation between a body and surrounding bodies. The two major considerations in the solution of such problems are a) shape and relative position of the surfaces and b) the emissivities of the surfaces. In this work it shall be assumed that all incremental areas on a pore have the same emissivity and, further, that little or no reflection occurs (i.e., the radiation hitting a surface is either absorbed or transmitted). Thus, the solution of the stated problem requires only that consideration a be satisfied. Consider two incremental surface areas dA 1 and dA2 of the same material in a general orientation to one another. Let dAl be at temperature TI and dAz be at T2. Fig. 2 illustrates the geometrical parameters involved. That is, 71, is the normal of dA, n2 the normal of dA2, r the line connecting the centers of each area, 81 the angle between nl and r, and Q2 the angle between 7,2 and r. Using Eq. [2] and the Lambert cosine law of diffuse radiation it is easily shown that:293 WdAf- dA, = ecr T*------^fpi------" dAidA2 [ 3a 1 and

Jan 1, 1970

In 1974, iron pellet production in the Great Lakes region reached the 53-million-tpy level, accounting for more than 88% of the nation's pellet production. By 1978, pellet output from the Great Lakes district will climb to at least 78 million tpy. To achieve this 50% increase in output, the US iron and steel industry is investing at least $1.25 billion in new mines and pelletizing plants, mostly in Minnesota and Michigan. The biggest effort is concentrated in the Mesabi Range of Minnesota, the heart of the US steel industry's major iron ore source: here, plans for two new taconite plants-one by Hibbing Taconite Co., and the other by Inland Steel Mining Co.-and three major expansions of existing facilities are already under way to boost Minnesota's total iron pellet capacity from the current 41.2 million tpy to 65 million tpy by 1978. The facilities being expanded are those of US Steel Corp. (Minntac operations), Eveleth Taconite Co., and National Steel Pellet Co.

Jan 11, 1975

P. H. Dudley, Yew York, N. Y. (communication to the Secretary*) :—The characteristics of Professor Home's metallurgical papers are, that he is able, from the mass of confusing evidence on the subject, to make an analysis and present hypothetical and essential principles in concrete form for consideration and discussion. I can appreciate, from the practical side of the subject, the labor of collecting and investigating the data which was essential to prepare the paper. Much of it necessarily came from material of preceding years of manufacture in which time was allowed for chemical reactions of the re-carburizer, and for the elimination of the oxidation-products before teeming the ingots. This practice gave a favorable time-element to free the metal from slag and other impurities— a requisite condition for the production of sound steel in the ingots. But, in allowing them to become cold before they were charged into the furnace, a subsequent time-element entered as a detrimental factor in the development of the pipe or shrinkage-cavities, which gave an ingot-structure deficient in soundness, at least in the upper portion. (The term slag is used in a general rather than in a strictly technical sense.) Traces of manganese sulphide are often associated with manganese silicates in the same thread or seam, and at other places they are separate and distinct. Interpretations from material thus manufactured must be made with due allowances for the methods of fabrication and the requirements of service. The only way we now have to estimate what the degree of soundness of the ingot-structure was, in the early foreign and American manufacture of steel rails, is by examination of the worn and failed material after years of service. We must remember also that the poorest material was long since consigned to the scrap-heap without any full record of its history. The rails from a given ingot cannot now be identified ; and in many

Jan 1, 1909

By Norman Lamont

The evaluation of certain reser-voir properties, such as porosity and fluid saturation, from electrical well surveys has been widely accepted in petroleum engineering. Various investigators have established relationships between these properties and certain parameters which affect the response of the electrical log. Among these are the resistivities of the mud, its filtrate, and its filter cake. In 1949, Patnode1 established a relationship between the resistivities of the mud and filtrate. The well logging service companies have contributed relationships for the mud-mud cake resistivities2,3 These have been valuable since it was the practice to measure only resistivity of mud at the well site. During the mid-1940's the industry began drilling wells with oil-emulsion drilling fluids. These were conventional aqueous muds with a dispersed oil phase. Since 1950, oil-emulsion muds have been used on an increasing number of wells each year. However, the practice of measuring only the resistivity of the mud at the well site has continued, and the mud filtrate and mud cake resistivities have been determined by the above-mentioned relationships. Service companies are now equipped to measure all three resistivities at the well site. An investigation was conducted on the resistivities of oil-emulsion muds, mud filtrates, and mud cakes to determine if these values conformed to the relationships for aqueous muds. TYPES OF MUDS Fifty-one oil-emulsion mud samples were prepared in the laboratory following a standard manual' published by a leading mud company. The diesel oil in the samples varied from 5 to 50 per cent, the majority of the samples being in the 10 per cent region. The basic aqueous mud types which were converted to oil-emulsion muds were commercial clay and bentonite muds, low pH and high pH, caustic-quebracho treated muds, and lime treated muds. The emulsions were stabilized by dispersed solids, lignins, lignosulfo-nates, sodium carboxymethyl cellulose, or sulfonated petrolatum. It is worthy of note that after a quiescent period of two weeks at room temperature all samples, regardless of emulsifying agent, remained stable. The make-up water for the muds was from the laboratory tap. Resistivities were varied by the addition of table salt to the water. A range of mud resistivities from 0.44 to 3.9 ohm-m was obtained in this way. Twenty-three field muds were tested. These covered the same range of mud types as did laboratory muds. Oil provinces of the Gulf Coast, South Texas, West Texas, Oklahoma, Montana, and Canada were represented. MUD TEST PROCEDURE Each mud was tested for density, viscosity, pH, and filter loss by standard testing techniques. The resistivity measurements were obtained with a Schlumberger EMT meter. This meter required small volumes of sample, e.g., 2 mm. Filtrate was obtained from a Standard Baroid fil-ter press at the end of a 30-minute test. The filter cake from the same test was used for cake resistivity measurements. Mud, filtrate, and cake samples were heated to 100" F in a constant temperature water bath prior to measurement of resistivities. RESULTS The relation between mud resistivity (Rm) and mud filtrate resistivity (Rmf) is shown in Fig. 1. The solid line represents an average for the data. The equation of this line is Rmf =0.876 (Rm) 1.075 . . (1) Arbitrary limits, indicated by the dashed curves, have been set. The majority of the data falls within these limits, but some points do lie outside the limits. The approximate equation Rmt = 0.88 Rm , . . . . (2) will give satisfactory results within these limits. The data on mud cake resistivity Rmc is shown in Fig. 2. The solid line is an average for the data. The equation for the line is Rmc = 1.306 (Rm)0.88 The dashed lines are arbitrary limits on the data. Within these limits, Eq. 3 may be simplified to Rmc = 1.31 Rm . . . . (4) DISCUSSION The limiting curves in Figs. 1 and 2 represent maximum deviations of ±25 per cent. Thus the use of the average curves can introduce considerable error. There is no substitute for accurate measurements of mud, mud cake, and mud filtrate resistivities at the well site. The mud sample tested should be representative of the mud opposite the formation being logged. The average mud filtrate resistivity curve of Fig. 1 is reproduced in Fig. 3 with two curves which have been published for clay-base aqueous muds2,3. The latter curves were determined from average values of a large number of drilling fluids. The three curves have essentially the same slope and the differences between them are from 7 to 22 per cent. Comparison is made only to illustrate the possibility of error

Jan 1, 1958

Uranium was the prima donna of 1978, and the exploration pace was fast and furious in traditional uranium producing areas such as the Powder River Basin, Grants mineral belt, San Juan Basin, and Uravan mineral belt. Adding fuel to the fire were several significant discoveries: The Date Creek Basin of western Arizona, the McDermitt caldera of northern Nevada, and Tallahassee Creek in Colorado's intermontane basin. Advances in solution mining haw resulted in deeper drilling on the Texas Coastal Plain, and the price of uranium has encouraged widespread exploration in frontier areas and non-sandstone environments.

Jan 5, 1979

By M. A. Grossman

The harden ability of most steels can be predicted within 10 to I5 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In the method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter", namely, the diameter of bar, in inches, that will just harden all the way through (absence of un-hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test The data bring out certain features rather clearly. For example: i. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals,,) are known; thus an "incidental,, chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful, as would appear to be common experience; observe that an increase from no manaanese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the fist small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using I.o per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, un-dissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum Passible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the

Jan 1, 1942

By M. A. Grossman

The harden ability of most steels can be predicted within 10 to I5 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In the method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter", namely, the diameter of bar, in inches, that will just harden all the way through (absence of un-hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test The data bring out certain features rather clearly. For example: i. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals,,) are known; thus an "incidental,, chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful, as would appear to be common experience; observe that an increase from no manaanese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the fist small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using I.o per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, un-dissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum Passible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the

Jan 1, 1942

By J. J. Jakosky

The fundamental hydrodynamic principles governing the production of oil from wells have been carefully studied and evaluated by many investigators. These prior studies are quite complete and cover virtually the entire field of oil production and recovery.' One of the most important measurements in production studies is that of the bottom-hole pressure at various rates of production.2 It is the purpose of this paper to outline the technique and economics of fluid-level measurements as applied to pumping wells and to review briefly other methods for obtaining bottom-hole data. The applications of bottom-hole pressure or fluid-level measurements are based on simple hydrodynamic principles. Under equilibrium conditions, pbh = hd + pg + pch [1] when pbk = bottom-hole pressure, Ib. per sq. in. absolute, h = height of fluid in well, ft., d = average fluid density, Ib. per sq. in. per foot, p, = weight of section of gas column 1 in, square from fluid level to casinghead, Pch = casinghead pressure, Ib. per sq. in. absolute. In words, equation 1 states that the bottom-hole pressure is equal to the weight hd of the column of fluid plus the weight of the column of gas between the fluid and the casinghead plus the casinghead pressure. At moderate rates of flow, the rate of production is approximatcly proportional to the difference between the reservoir, or static bottom-hole. pressure and the flowing or producing pressure; i.e.: Q = c(pr - pbh) [2] pr = the reservoir pressure, c = the constant of proportionality. However, at production rates approaching zero and also at high rates the proportionality may break down. By combining equations 1 and 2 the

Jan 1, 1939

By J. J. Jakosky

The fundamental hydrodynamic principles governing the production of oil from wells have been carefully studied and evaluated by many investigators. These prior studies are quite complete and cover virtually the entire field of oil production and recovery.' One of the most important measurements in production studies is that of the bottom-hole pressure at various rates of production.2 It is the purpose of this paper to outline the technique and economics of fluid-level measurements as applied to pumping wells and to review briefly other methods for obtaining bottom-hole data. The applications of bottom-hole pressure or fluid-level measurements are based on simple hydrodynamic principles. Under equilibrium conditions, pbh = hd + pg + pch [1] when pbk = bottom-hole pressure, Ib. per sq. in. absolute, h = height of fluid in well, ft., d = average fluid density, Ib. per sq. in. per foot, p, = weight of section of gas column 1 in, square from fluid level to casinghead, Pch = casinghead pressure, Ib. per sq. in. absolute. In words, equation 1 states that the bottom-hole pressure is equal to the weight hd of the column of fluid plus the weight of the column of gas between the fluid and the casinghead plus the casinghead pressure. At moderate rates of flow, the rate of production is approximatcly proportional to the difference between the reservoir, or static bottom-hole. pressure and the flowing or producing pressure; i.e.: Q = c(pr - pbh) [2] pr = the reservoir pressure, c = the constant of proportionality. However, at production rates approaching zero and also at high rates the proportionality may break down. By combining equations 1 and 2 the

Jan 1, 1939

By Herbert Hoover

I HAVE been greatly honored as your unanimous choice for President of this. Institute, with which I have been associated during my entire professional life. It is customary for your new President, on these occasions, to make some observation on matters of general interest from the engineer's standpoint. The profession of engineering in the United States comprises not alone scientific advisers on industry but, in great majority, is comprised of the men in administrative positions. In such positions, they stand midway between capital and labor. The character of your training and experience leads you to exact and quantitative thought. This basis of training in a great group of Americans furnished a wonderful' recruiting ground for service in these last years of tribulation. Many thousands of engineers were called into the army, the navy, and civilian service for the Government. Thousands of high offices were discharged by them with credit to the profession and the nation. We have in. this country, probably, one hundred thousand professional engineers. The events of the past few years have greatly stirred their interest in national problems.' This has taken practical. form in the maintenance of joint committees for discussion of these problems and support to a free advisory bureau in ,Washington. The engineers want nothing for themselves from Congress.. They want efficiency in government, and you contribute to the maintenance of this bureau out of sheer idealism. This organization for consideration of national problems has had many subjects before it, and I propose to touch on some of them this evening.

Jan 1, 1920

Thomas T. Read, New york, N. Y. (communication to the Secretary *):—At the meetings of English technical societies it not infrequently happens that, during the discussion of a paper, someone will arise to say that although he highly appreciated the material presented, nevertheless he believed it would have been better if some other phase of the question had been more highly emphasized. Assuming that this form of discussion is permissible in the Institute, I should like to reiterate the point made by Prof. A. J. Moses that conclusive proof of the identity of the minerals in question is an essential feature of the study of ores in this way. This is also expressed by Paul Krusch in his recent valuable paper on the sulphide ores (in which he arrives at conclusions diametrically opposed to those of Mr. Graton), as follows: "The diagnostic properties of the various ore minerals are known to but a limited circle of investigators." Many earlier investigators began the study of ores beneath the microscope by reflected light, but discontinued their work, in most cases, because they were unwilling to undertake the great amount of preliminary work necessary to securely establish a basis for their inferences. It is evident that Messrs. Graton and Murdoch realize that the promised later paper on diagnostic characters will be the more important of the two, but the point should be emphasized to forestall a flood of literature from other investigators who may gain the impression that the brief survey of polished specimens is a vade mecum to incontrovertible conclusions as to any given ore deposit.

Jan 1, 1914

ALABAMA Anniston.-Bretz, J. A. Carrington, F. G. Gerber, A. B. Klugh, B. G. Semple, R. A. Ashland.-Barton, .J. Bessemer.-Abbott, C. E'. Ball, T. L. Beaver, J. J. Ferguson, V. Salmon, H. S. Sehaber, C. F. Whatley, W. J.

Jan 1, 1923

By Sidney Sigel, J. Gardner Brooks, Irvin R. Kramer

In 1942 Grossmannl proposed that the hardenability of a steel may be calculated from its chemical composition by considering the base hardenability associated with its carbon content and grain size and multiplying this base by factors for each element present. Since Grossmann's original publication, several investigaton2-6 have reexamined the multiplying factors for the individual elements and in general have found that the multiplying principle is valid. However, some of the individual factor curves developed have been in poor agreement. Inasmuch as the carbon-factor curve obtained by Grossmann was dependent Lipon the factors for all the other alloying elements present in the steel, it logically followed that his results were in need of correction in the light of the new data available for manganese, silicon, and the other alloying elements. Furthermore, in order to avoid the possibility that errors in the manganese, silicon, or other curves might influence the carbon-factor curve, investigation of iron-carbon alloys containing little or no manganese and silicon was necessary. That the effect of carbon on hardenability was greater than indicated by Grossmann is shown by a comparison of the diameters of completely hardened rounds of iron-carbon alloys with the ideal critical diameter calculated from Grossmann's factors. These alloys have a greater hardenability in a finite quench than predicted by Grossmann's factors for an infinite quench (Table I). Among the other important variables that were in need of further investigation were the effect of deoxidation practice on the grain-size correction curves and the effect of stable carbide-forming elements on the depth of hardening. Most Of the work by Kramer, Hafner, and Toleman4 was done on silicon-killed steels. It was not known whether Gross-mann's grain-size correction curves, determined on aluminum-killed steels, was valid when applied to steels with different deoxidation practice. More data on the

Jan 1, 1947

By J. Gardner Brooks, Sidney Sigel, Irvin R. Kramer

In 1942 Grossmannl proposed that the hardenability of a steel may be calculated from its chemical composition by considering the base hardenability associated with its carbon content and grain size and multiplying this base by factors for each element present. Since Grossmann's original publication, several investigaton2-6 have reexamined the multiplying factors for the individual elements and in general have found that the multiplying principle is valid. However, some of the individual factor curves developed have been in poor agreement. Inasmuch as the carbon-factor curve obtained by Grossmann was dependent Lipon the factors for all the other alloying elements present in the steel, it logically followed that his results were in need of correction in the light of the new data available for manganese, silicon, and the other alloying elements. Furthermore, in order to avoid the possibility that errors in the manganese, silicon, or other curves might influence the carbon-factor curve, investigation of iron-carbon alloys containing little or no manganese and silicon was necessary. That the effect of carbon on hardenability was greater than indicated by Grossmann is shown by a comparison of the diameters of completely hardened rounds of iron-carbon alloys with the ideal critical diameter calculated from Grossmann's factors. These alloys have a greater hardenability in a finite quench than predicted by Grossmann's factors for an infinite quench (Table I). Among the other important variables that were in need of further investigation were the effect of deoxidation practice on the grain-size correction curves and the effect of stable carbide-forming elements on the depth of hardening. Most Of the work by Kramer, Hafner, and Toleman4 was done on silicon-killed steels. It was not known whether Gross-mann's grain-size correction curves, determined on aluminum-killed steels, was valid when applied to steels with different deoxidation practice. More data on the

Jan 1, 1947

By Oswald J. Heinrich

THIS question having been repeatedly raised, and particularly revived in a discussion at the last meeting of the Institute, I beg to submit the following remarks, based partly upon personal experience, partly upon the results of large works in Europe, establishing, years ago, the practicability of certain methods, which may therefore be considered to have passed the stage of mere experiment. Before entering upon the merits of one system or the other, it is indispensable to lay down some recognized principles, which ought to serve as guides, in arriving at fair judgments in questions of this character. In a profession like that of mining, locally so much influenced by combinations of circumstances too various to mention, it is difficult to do more than lay down the main features of a system based upon general laws and recognized facts, leaving the details to the sound judgment and experience of the engineer, who, by virtue of his education, ought to be able to make such choice and such modifications in the plans of a mine as the particular case demands. Mineral resources, in some countries the sole property of the owner of the soil, in others controlled by the strong hand of a government, are nevertheless a gift of nature, in which, indirectly, the whole of the human race has as real an interest as the immediate owner himself. This interest requires, at least, that no unnecessary waste of

Jan 1, 1874