Search Documents

By J. Waldman, M. B. Bever, A. K. Jena

The heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of one solid solution have been measured by tin solution calorimetry. The heats of formation are analyzed in terms of the quasichemical theory. If the enthalpy diffel-ence between a hypothetical fcc form and the hcp form of cadmium is taken into account, this analysis does not lead to the conclusion put forth in the literature that electronic effects make significant contributions to the heats of formation of silver-rich Ag-Cd solid solutions. The temperature dependence of the heats of formation is appreciable and negative near 78ºK, but decreases gradually to nearly zero abore 400°K. The relative partial enthalpies per grarn -atom of silver at 541°K and cadmium at 532" and 541°K in tin have also been determined. THE composition range of the silver-rich Ag-Cd solid solutions stable at room temperature extends to about 40 at. pct Cd. Heats of formation of these solid solutions at 308" and 723°K have been measured by solution calorimetry.1,2 Heats of formation for an average temperature of 800°K have also been calculated from vapor pressures.2,3 The heats of formation deviate from the values predicted by the quasichemical theory above about 30 at. pct Cd. This deviation has been attributed to electronic effects at the Brillouin zone boundaries.2 The heats of formation of Ag-Cd alloys are essentially the same at 308", 723", and 800°K; consequently the temperature dependence of the heat of formation d?H/dT = ?Cp is vanishingly small, although from the exothermic heats of formation a negative value would have been expected. In the investigation reported here the heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of 1 solid solution have been measured by tin solution calorimetry. The results are analyzed in terms of the quasichemical theory and the dependence of the heats of formation on temperature is discussed. The relative partial enthalpies per gram-atom of silver in tin at 541" and cadmium in tin at 532" and 541°K were obtained in the course of this investigation. The values of the temperature dependence of the relative partial enthalpies per gram-atom of silver in tin derived from the data reported by various investigators2,4-9 are contradictory. The literature contains only a value for 517°K of the relative partial enthalpy per gram-atom of solid cadmium in tin.2 EXPERIMENTAL PROCEDURES Samples of Ag-Cd solid solutions were prepared by melting weighed amounts of silver (99.99 pct pure) and cadmium (99.95 pct pure) in graphite crucibles under a flux of molten potassium chloride.10 The solidified ingots were sealed in evacuated Vycor tubes and annealed at 775°K for 10 days. The ingots were swaged and drawn into wires. The wires, sealed in evacuated Pyrex tubes, were held at 725°K for 5 hr and cooled to 365°K at an average rate of 2.5ºK per hr, followed by furnace cooling to room temperature. Chemical analysis of samples taken from different parts of each ingot gave no indication of segregation. Metallographic examination showed the samples to be homogeneous. Samples of the solid solutions or of the component elements were added to tin-rich baths in a calorimeter." At the start of a run the bath consisted of pure tin. Silver was used in the form of wire of 0.01-in. diam as supplied and cadmium in the form of lumps. Gold (99.999 pct pure) was added with the samples in order to reduce the endothermic heat effect of additions of Ag-Cd solid solutions. Samples of only one composition were added in a run and the ratio of the weight of alloy to that of gold was the same in all additions of a given run. In each run several calibrating additions of tin were made from 273°K. The heat contents of tin were calculated from the following equation, which is based on published data:12 (HTºK- H279º) = 6.70 T - 72,300/T + 20 cal/gram-atom; 505°K < T < 650°K The heat effect of each addition was plotted against the average of the sum of the atom fractions of solutes in the solution before and after that addition. The total concentration of solutes at the end of a run was less than 2 at. pct. In this range the heat effect was a linear function of the atom fraction of the solutes. The heat effect at infinite dilution and the composition dependence of the heat effect were obtained from the plots. RESULTS AND DISCUSSION Evaluation of Data. The linear dependence on composition of the heat effects of additions suggests that in the dilute range the enthalpy interaction coefficients other than the first-order coefficients of silver, cadmium, and gold are negligible, as shown in a concurrent publication.13 The heat effects at infinite dilution and the values of the composition dependence of the heat effects are listed in Table I.

Jan 1, 1970

By William J. Gillich, Gerald L. Moss

PREVIOUS studies of the shock loading of randomly oriented polycrystalline aggregates have firmly established that, after rather short load duration, hydrostatic compression closely approximates the shocked state.&apos; However, McQueen deduced from pressure measurements with good time resolution that, during shock loading, metals begin to undergo a stress relaxation at the yield stress. He suggested that the relaxation is due to plastic deformation accompanying the change from a one-dimensional compression to a three-dimensional, hydrostatic, compression.&apos; Stress relaxation may occur faster as stress is increased above the yield stress, but the existence of unidirectionally compressed states for finite times suggests that the concept of a unidirectionally distorted lattice should furnish considerable insight into the mechanical behavior of materials subjected to shock loading. Here, a crystallographic analysis is presented for the hypothetical situation where atom motion may be considered as unidirectional which, as indicated above, is a useful extension of the macroscopic concept of shock loading to the microscopic domain. Only motion caused by the com-pressive forces is treated; i.e., lattice vibrations upon which this motion is superimposed, as discussed by Fitzgerald, are ignored.3 The purpose of the analysis to be presented is to develop a description for single crystals of the lattice rotations that occur for idealized uniaxial strain deformation. The usefulness of such an analysis in realistic deformation is to give a method of specification of those properties of an initially distorted lattice which would affect the subsequent deformation. Non-axial complications that arise experimentally, such as off-axis rarefaction waves, must be treated in proper context. Consider the material element shown in Fig. 1 and let the compression be uniform at all regions of the element. Then, any interior point of the element is displaced in proportion to its distance from the base of the element. Accordingly, if the top of a unit element is displaced by an amount, (-K), with respect to the base, a point P(X, Y) will be displaced by (-KY). Crystal planes are, therefore, rotated by the compression. Analysis of this rotation may be accomplished from the geometry shown in Fig. 1 where the line OP is the edge of the plane {hkl} and N is its normal. The orientation of the crystal plane with respect to the shock direction is specified by the angle, before deformation. After deformation the edge of plane {hkl}

Jan 1, 1969

By J. H. Swisher

The solubility of sulfur and rate of solution of sulfur in pure Lron were measured in H2S + H2 and H2S + H2 H2O gas mixtures. The solubility and diffusivity of sulfur at 1410°Care 0.13 pet S and 1.0 x 10-5 sq cm per sec, respectively. The solubility iS the same, but the rate of sulfurization is slower in the presence of H2O in the reacting gas. Under these conditions, the over-all rate is controlled jointly by a slow surface reaction and by solid-state diffusion; the mechanism for the surface reaction has not been identified. KNOWLEDGE of the behavior of sulfur in solid iron is desirable for the metallurgy of such products as free machining steel, where a high sulfur level is required, and inclusion-free high-strength steels, where the sulfur specifications are very low. The present investigation was undertaken to check previously reported values for sulfur solubility and diffusivity in 6 iron, and to study the poisoning effect of chemisorbed oxygen on sulfurization kinetics in H2-H2S-H2O gas mixtures. All of the experiments were performed at 1410°C. The thermodynamic behavior of sulfur in 6 iron was the subject of a paper by Rosenqvist and Dunicz.&apos; The sulfur solubility at 1400" and 1500°C was determined by equilibrating pure iron specimens with H2-H2S gas mixtures. The maximum solubility of sulfur in 6 iron was alsc determined by Barloga, Bock, and parlee2 by reacting iron wires with sulfur in sealed capsules. In another investigation, the diffusion coefficient of sulfur in 6 iron at temperatures up to 1450°C was measured by Seibel.3 The method used was to measure sulfur concentration profiles in diffusion couples containing radioactive sulfur EXPERIMENTAL Apparatus. A vertical resistance furnace wound with molybdenum wire and containing a recrystallized alumina reaction rube was used for the experiments. The hot zone in the furnace was approximately 2 in. long with a temperature variation of ±3oC. The hot zone temperature was automatically controlled to within ±2°C, and the test temperature was measured with a pt/Pt-10 pet Rh thermocouple before and after each experiment. Flow rates of the reacting gases were obtained using capillary flow meters. Materials. The source of H2S in the gas train was a premixed cylinder containing 5 pet H2S in H2. This mixture then was diluted with additional hydrogen and argon. In some experiments, water vapor was introduced by passing hydrogen and argon through a column containing 10 pet anhydrous oxalic acid and 90 pet oxalic acid dihydrate. The vapor pressure of water above this mixture is well-known.4 Argon was used as a diluent to minimize thermal segregation of H2S in the furnace5 and to reach higher H2O:H2 ratios than could be obtained in mixtures of H2 and H2S alone. Argon was purified by passage over copper chips at 350°C and subsequently over anhydrone. Hydrogen was purified by passage over platinized asbestos at 450°C and then over anhydrone. The H2-H2S mixture was purified by passage over platinized asbestos and then over P2O5. The specimen stock was made by melting and vacuum-carbon deoxidizing electrolytic "Plastiron" in a zirconia crucible. The principal impurities are listed in Table I. In some of the equilibrium experiments, six-pass zone-refined iron was used to minimize impurity side effects. This zone-refined iron had a total impurity level of about 25 ppm. Procedure. Specimens were annealed in hydrogen for a period of at least 2 hr at the beginning of each experiment. The specimens were held in the reacting gas for times varying between 10 min and 17 hr, and cooled to room temperature in a water-cooled stainless-steel block at the bottom of the furnace. The pH2S/pH2 ratios reported are those for gas equilibrium at 1410°C. Calculations based on available thermodynamic data8 showed that the only other gaseous8 species that formed in significant amounts in the furnace were S2 and S. Even when water vapor was introduced into the gas mixture, the concentrations of SO2, SO, and so forth, were negligible. The initial partial pressure of H2S was therefore corrected for its partial dissociation to S2 and S in determining the equi-

Jan 1, 1968

By R. W. Nash, A. E. Schwaneke, V. R. Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western prophyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized - 2.5 + 1.3-cm (- 1 + 112- in.) ores from the Kingston (0.9% Cu) and Centennial (1.6% Cu) mines of Upper Michigan. Concentrates of 4.0% and 7.5% Cu, respectively, were obtained at recoveries of 85 and 80% of the copper in the feed. Eighty percent of the sorted ore was rejected as tailing. Sorting larger fragments improved the separation efficiency. Tests on - 10+ 5-cm (- 4 +2-in.) sized Kingston (1.6% Cu) and Centennial (2.1 % Cu) ore samples yielded concentrates of 4.3 and 4.5% Cu, respectively, with corresponding recoveries of 92 and 91 %. A bout 60% of the sorted ore was discarded as tailing. Porphyry copper sulfide ores also responded to electronic sorting but at a lower separation efficiency. Sorting response was affected by the degree of segregation.

Jan 1, 1979

By B. W. Frazier

Jan 1, 1882

By D. A. Farmen

INTRODUCTION In early 1978, engineering personnel at The Carter Mining Company began using photogrammetry coupled with a computer modeling technique to aid in mine planning efforts. The decision to develop this approach was based on the following needs: 1. A method to accurately capture excavated quantities for reporting purposes, 2. A method to produce accurate up-to-date maps for planning purposes, and 3. A computer-based mine-planning technique that would be compatible with techniques used in the past. The system developed utilizes a photogrammetric contractor to provide thousands of aerially-surveyed data points for input into the computer system. Each month the Rawhide and Caballo mines are flown by the photogrammetric contractor. The terrain of the active pit area is digitized and punched out on computer cards. This information is read into The Carter Mining Company&apos;s computer facilities, and an updated two-dimensional topographic grid model of the pit is generated. This surface is used to generate quantities moved during the month, to update isopachs, and to update quantities contained in fixed block progression polygons used for forecasting purposes. The system has greatly reduced the amount of manhours spent in field surveying and provides a useful tool for expeditiously evaluating many different forecast cases. It also provides the

Jan 1, 1983

By M. S. Burton, G. V. Smith, A. Rosen

The kinetics of re crystallization and the effect of recovery on recrystallization of pure iron were investigated within the temperature range of 517" to 632 OC. Grain growth and activation energies were also studied. Two stages can be distinguished during recrystallization; the first is gvowth-controlled and the second is nucleation-controlled. The extent to which the first stage succeeds before the second stage begins depends on both temperature of recrystallization and temperature of recovery. The softening of cold-worked metals and alloys due to transformation of the deformed crystals to strain-free equiaxed grains during annealing is well-known, and early inestiators established that recrystallization kinetics is strongly influenced by minute quantities of impurities. Generally, it is believed that impurities decrease the rate of recrystallization and the rate of grain growth. To understand the basic phenomena of recrystallization, investigations should be on pure materials. Most of the research on high-purity materials has been on metals having the fee Bcc materials, and especially high-purity iron, have been studied only in recent years. It is known that recovery may influence recrystalliation;" however, no general description of the influence, applicable to all materials, has been presented. This paper presents results of a study of the recrystallization kinetics of high-purity iron, after 60 pct cold deformation by drawing, with particular reference to the influence of recovery on the rates of recrystallization and grain growth. From observations of these rates, conclusions are drawn concerning nucleation. MATERIAL AND EXPERIMENTAL PROCEDURE Preparation of Material. High-purity iron, prepared by zone refining of vacuum-melted electroiytic iron at Battelle Memorial Institute under sponsorship of the American Iron and Steel Institute, was used in this study. Table I gives the reported chemical analysis of the material, taken at a point near the last molten zone and thereby rep- resenting the maximum impurity level for the entire bar. Prismatic specimens, approximately 10 x 10 X 50 mm, were sawed from the 50-mm-diam bar, perpendicular to the zone-refining direction, and turned to cylindrical shape. These specimens were sealed in quartz capsules under vacuum, approximately 10"e mm Hg, austenitized at 930° C for 15 min, slowly cooled, removed from the capsules, and cold-worked in air by swaging to approximately 20-pct reduction of area. The encapsulating, austenitizing, and swaging operations were repeated two additional times, after which the samples were encapsulated, austenitized, and cold-drawn to 60-pct reduction of area. A further vacuum anneal at 630°C for 120 min and cold drawing to 60-pct reduction of area produced wire 2.8 mm in diameter. The drawn wire was electropolished to remove deformed material on the surface, after which it was sawed into 4-mm-long specimens for the recrystallization study. Microscopical examination before the final cold reduction revealed equiaxed grain structure with very fine grains in a thin layer near the surfaces of the specimen and nearly uniform ASTM 3-4 grain size in the center. Recrystallization Heat Treatment. a) Direct Recrystallization of Cold-Worked The 60 pct cold drawn iron specimens were recrystallized at five temperatures, 517, 556, 590°, 612, and 632C, in a lead bath covered with graphite (the temperature was controlled to 1°C). Specimens were treated for twelve different times at each temperature, and all were water-quenched after heat &eatment. b) Recrystallization Following Preliminary Recovery Heat Treatment. After cold working, specimens were sealed into quartz capsules under vacuum, 105 mm Hg, and recovery-annealed at 362", 400", and 440°C for 20 hr prior to recrystallization. No evidence of recrystallization was found

Jan 1, 1964

By John Birkinbine

Secretary&apos;s Note.—In printing this paper in the present volume, the figures given in the pamphlet edition have been brought more nearly up to date, the product of 1899 being in many instances inserted. Iron-Ore Resources. In a paper presented to the Institute in 1897,* I discussed the iron-resources of the United States as then developed, calling attention to some principal sources upon which other countries depended. The following statement will give a general idea of the amounts, as compiled from the latest official records, of ores won, and metal produced, in the nations which are important contributors to the world&apos;s output. Unfortunately these are not all contemporaneous, since in some countries the statistics do not appear until after one or more years. The statement covers not only pig-iron and iron-ore, but also manganese-ore —the manganese mined being principally used in the production of spiegeleisen or ferro-manganese, and these alloys being generally included in the pig-iron output. Table I, which epitomizes the present situation, shows respectively the countries and the quantities of iron-ore and man-

Jan 1, 1901

By Paul D. Merica, O. B. J. Fraser

PROBABLY the first metallic objects used by man were nickel alloys. In search for flints suitable for the fashioning of their rude tools, our paleolithic ancestors, some 25,000 years ago, quite likely may have come upon some of those heavy, metallic fragments that we now know as meteorites, which consist of an alloy of nickel and iron containing usually from 5 to 15 pct of nickel. Whether paleolithic man ever did discover and use meteoritic fragments, his sketchy records do not actually disclose. We do know, however, that such fragments have been found and used by peoples, particularly the North American Eskimos, for weapons and implements in just the same manner as stones, and prior to any knowledge by those peoples of the reduction of metals from ores. Meteoritic showers were recorded frequently in earliest times and the meteorites often were found and fashioned into useful objects. The ancient Arabic and other myths of "invincible swords fallen from heaven" seem thus to have had a very definite basis in fact, and such weapons, of meteoritic material, have actually been re- covered from archeological excavations. It thus seems probable that meteoric nickel-iron was found and used long before iron was recovered by smelting iron ores (perhaps about 1200 B.C.) and probably even before there was knowledge and use of bronze and gold. Although many centuries were to pass before nickel was first isolated, in 1751, from Swedish ores and recognized as an elemental

Jan 1, 1953

By Waldemar Lingren

CONTENTS. PART I.-GENERAL FEATURES. [ ]

Jan 1, 1902

By John Wulff, J. H. Hollomon

Service failures in brass condenser tubes are often due to corrosion. One of the commonest types of corrosion reveals a surface structure of redeposited copper.&apos; The study of the effect of alloy addition agents in preventing this kind of corrosion has received impetus from the extensive publication of Bengough and May.2 The mechanism of such inhibition gauged from immersion corrosion,2 cell corrosion,3 and electrolytic potential4 measurements is controversial. This controversy may be attributed in part to a lack of definite knowledge5 of the actual nature of the initial films formed in corrosion experiments. In our own corrosion work on copper and 70-30 brass this lack became apparent and necessitated an examination of surface films by X-ray and electron diffraction methods. The present paper is but an introduction to the subject of inhibition and reports the structure of films formed in active corrodents. Experimental Procedure The arsenical coppers and brasses used in this investigation were made by one of the writers* in the plant of the Revere Copper and Brass Co. at Rome, N. Y. Standard commercial melting practice was followed. O.F.H.C. copper and electrolytic zinc were used and all arsenic additions were made by additions of a master copper alloy. The final analyses are given in Table I. Likewise, the extrusion, cold-rolling, and intermediate anneals employed followed standard usage. Final heat-treatments were given to all materials to produce a similar grain size (0.035 to 0.045 mm. for brass and 0.015 to 0.025 for copper) for the alloys containing various percentages of arsenic. Samples 1/2 by M by 1/4 in. were cut from sheet material resurfaced and finished with 0000 metal-lographic papers. The surfaces were all degreased in alcohol and benzine before immersion. After immersion in the corrodent, they were washed gently in tap water, dipped first in alcohol and then in pure benzine and allowed to dry in the diffraction apparatus. The reflection electron diffraction apparatus used has been described by Burwell and Wu1ff.6 Fig. I is typical of the photo-grams obtained. The X-ray apparatus was

Jan 1, 1941

By John Wulff, J. H. Hollomon

Service failures in brass condenser tubes are often due to corrosion. One of the commonest types of corrosion reveals a surface structure of redeposited copper.&apos; The study of the effect of alloy addition agents in preventing this kind of corrosion has received impetus from the extensive publication of Bengough and May.2 The mechanism of such inhibition gauged from immersion corrosion,2 cell corrosion,3 and electrolytic potential4 measurements is controversial. This controversy may be attributed in part to a lack of definite knowledge5 of the actual nature of the initial films formed in corrosion experiments. In our own corrosion work on copper and 70-30 brass this lack became apparent and necessitated an examination of surface films by X-ray and electron diffraction methods. The present paper is but an introduction to the subject of inhibition and reports the structure of films formed in active corrodents. Experimental Procedure The arsenical coppers and brasses used in this investigation were made by one of the writers* in the plant of the Revere Copper and Brass Co. at Rome, N. Y. Standard commercial melting practice was followed. O.F.H.C. copper and electrolytic zinc were used and all arsenic additions were made by additions of a master copper alloy. The final analyses are given in Table I. Likewise, the extrusion, cold-rolling, and intermediate anneals employed followed standard usage. Final heat-treatments were given to all materials to produce a similar grain size (0.035 to 0.045 mm. for brass and 0.015 to 0.025 for copper) for the alloys containing various percentages of arsenic. Samples 1/2 by M by 1/4 in. were cut from sheet material resurfaced and finished with 0000 metal-lographic papers. The surfaces were all degreased in alcohol and benzine before immersion. After immersion in the corrodent, they were washed gently in tap water, dipped first in alcohol and then in pure benzine and allowed to dry in the diffraction apparatus. The reflection electron diffraction apparatus used has been described by Burwell and Wu1ff.6 Fig. I is typical of the photo-grams obtained. The X-ray apparatus was

Jan 1, 1941

By Beeby Thompson

ALTHOUGH the exclusion of foreigners and private owners from participation in the development of the. Russian oil fields prevents first-hand information being obtained, both official and private news indicate a growing appreciation of the value of the country&apos;s oil resources. Notwithstanding the suppression of that initiative and energy which only ambition can adequately stimulate, the industry is progressing and exports of products are assuming an importance that cannot be disregarded as an economic factor in the world&apos;s oil business. The following notes and observations must be regarded mainly as the views of one who has closely followed the fortunes of Russian oil, when considering the changes that have taken place in geological knowledge and oil-field technique, which have so profoundly modified oil-fields methods. Russia is fortunate in having retained the services of. a few scientists and technologists whose devotion to science has superseded their personal inclinations, and to these few men must be attributed the slow, but nevertheless striking, progress that has been made. The productive oil fields of Russia are centered around the Caspian Sea which, with its connected river system, constitutes such an ideal means of internal distribution for products. From the group of oilfields of which the. city of Baku forms a center, oil is pumped to Black-town, a suburb of Baku, where all the refineries are situated. The next important group of oil fields is located in the Terek district near Grosny, where refineries are erected and the products are piped or carried by tank cars to Petrovsk for the internal Russian market, or sent to the Black Sea by rail. A third oil field is spread over the province of Uralsk, north of the Caspian, Sea, the main port of outlet being Gourief, at the mouth of the River Ural. In Trans-Caspia there are two oil-field centers, one near Krasnovodsk on Chelekan Island, and one in Central Asia at Ferghana. The product of the former fields is transported to Baku for treatment, while the output of the Turkestan field is refined and consumed locally, mainly by the railway.

Jan 3, 1925

By Otis M. Clarke

The Eufaula bauxite-kaolin district in southeastern Alabama is an important source of raw material for the refractory industries in the United States. At the present time, five companies are mining and processing bauxite and kaolin from this district and a sixth company is holding substantial reserves. Mining operations are expanding, but finding new ore reserves is a major problem. The Geological Survey of Alabama sponsored geologic research in the Eufaula district to: (1) investigate the

Jan 1, 1973

US 4,135,913-Extraction of nickel values from iron-containing nickel sulfide ore, particularly pentlandite or nickeliferous pyrrhotite A mixture of raw ore, roasted ore, or iron powder, and coal as a reductant is heated to a temperature of 800- 1000° C in a nonoxidizing atmosphere to convert the bulk of the iron content to metallic iron while diffusing into the iron the bulk of the nickel, the mixture cooled, and the cool material separated into a magnetic fraction containing most of the nickel and a non-magnetic gangue fraction A Illis arid L S Renzoni, assigned to International Nickel Co, Inc Jan 23, 1979 7 pp (75-21) Filed 10-10-75 (621,343) Priority Canada, 10-27-72 (155,032) Same Canadian 981,910, dated Jan 20, 1976 Same British 1,389,145, dated Apr 3, 1975 US 4,135,917-In the recovery of gallium from a solution obtained by the digestion of bauxite or nepheline in an alkali solution for the production of alumina, the digestion solution is neutralized, the neutralized solution evaporated to an op¬timum caustic alkali concentration and adjusted to a ratio of alkali metal oxide to alumina of above 2, the corrected solu¬tion contacted with a gallium-aluminum alloy, arid high-purity gallium recovered from the solution by electrolysis or cemen¬tation K A Badaliants, et al Jan 23, 1979 6 pp (75-109) Filed 12-19-77 (862,201) Priority USSR, 12-22-76 (2,428,¬006) US 4,135,918-Extraction of copper from copper sulfide ore containing also one or more of the metals iron, nickel, arid cobalt Ore is roasted at a temperature of 750-800° C to expel sulfur, the sulfur-free calcine slurried in water containing a sufficient amount of sulfuric acid to supplement any sulfuric acid formed in situ, the slurry heated at 150-165° C in the presence of a reducing gas to form soluble sulfates of metals other than copper while reducing copper to elemental form, arid the slurry filtered to recover copper solids Any precious metals present in the ore will report with the copper solids V A Ettel, A P Devuyst, R Sridhar, arid C. E O&apos;Neill, as¬signed to International Nickel Co, Inc Jan 23, 1979 5 pp (75-117) Filed 3-2-78 (882,610) Priority Canada, 5-13-77 (278,360)

Jan 1, 1980

By Raymond D. Sloan

Retaining third place in crude-oil production among the nation&apos;s oil-producing states, Oklahoma&apos;s output in 1942 totaled 137,792,000 bbl., a decline of 9.4 per cent from the previous year&apos;s total of 152,117,000 bbl. Production declined from an average of 403,000 bbl. daily in January 1942 to an average of 355,000 bbl. during December, a reduction of 48,000 bbl. daily (11.9 per cent) during the year. At the end of 1942 it would appear inevitable that the downward trend in production will continue in 1953 unless halted in the immediate future by greater than normal discoveries and development. To Jan. I, 1943, Oklahoma has produced 5,067,013,000 bbl. oil crude oil. Development and Exploration Development dropped abruptly in 1942, reflecting the lack of any sizable discoveries and the effect of the provisions of Federal Well Spacing Order M-68, which became effective in December 1941. In all, 1210 wells were drilled in 1942. This represents a decrease of 42.7 per cent from the 1941 total of 2110. Of the total wells completed, 553 (45.7 per cent) were oil wells with an average initial production of 443 bbl.; 102 (8.4 per cent) were gas wells with an average initial of 3,359,000 cu. ft.; and 555 (45.9 per cent) were dry. Although the number of completions declined sharply, the total of 320 wildcats completed (26.4 per cent of all wells) repre-sents a decrease of only 2.7 per cent from the previous year&apos;s figure of 329. Of the wildcats drilled, 44 (13.8 per cent) were oil wells, 13 (4.0 per cent) were gas wells, and 263 (82.2 per cent) were recorded as failures. Reconditioning of wells throughout the state resulted in a total recompletion of 355 wells. Of these, 234 were oil wells with a combined initial production of 96,808 bbl., 32 were gas wells with a total initial of 381,488,000 cu. ft., and 89 were abandoned. None of the 26 pools found in 1942 has developed into a major discovery. The Pauls Valley pool, Garvin County, is the most outstanding. Since its discovery in April, 14 wells with an average initial of 1898 bbl. have produced 803,000 bbl. of 42&apos; gravity oil from the Bromide zone. Development in this pool is believed to be almost completed. Other of the more important discoveries are the East Watchorn pool, Pawnee County; Guthrie Townsite and West Navina, Logan County; Brooksville and Macomb, Pottawatomie County, and the Liberty and Northeast Lucien discoveries in Noble county. The East Watchorn pool, at the close of the year, had 14 completed oil wells with an average initial of 989 bbl. from the Wilcox sand at 3930 it.; Guthrie Townsite, one well with an initial of 840 bbl. from dolomite at 5600 It.; West Navina, six wells with an average initial of 284 bbl. in the Lay ton sand at 5050 ft., Brooksville, eight wells in the Hunton at 4800 ft. with an average initial 01 355 bbl.; Macomb, one well with an initial of 160 bbl. in the IIunton at 4700 ft.; the Liberty pool, one well with an initial of 1268 bbl. in the second Wilcox at 4500 ft., and two wells in the Tonkawa sand at 2500 ft., with an average initial of 230 bbl. In the Northeast Lucien pool, four wells were completed in the Wilcox at 5380 ft. for an average initial of 1164 bbl., and one well was completed in the Viola lime at 5255 ft. for an initial of 55 barrels.

Jan 1, 1943

By Raymond D. Sloan

Retaining third place in crude-oil production among the nation&apos;s oil-producing states, Oklahoma&apos;s output in 1942 totaled 137,792,000 bbl., a decline of 9.4 per cent from the previous year&apos;s total of 152,117,000 bbl. Production declined from an average of 403,000 bbl. daily in January 1942 to an average of 355,000 bbl. during December, a reduction of 48,000 bbl. daily (11.9 per cent) during the year. At the end of 1942 it would appear inevitable that the downward trend in production will continue in 1953 unless halted in the immediate future by greater than normal discoveries and development. To Jan. I, 1943, Oklahoma has produced 5,067,013,000 bbl. oil crude oil. Development and Exploration Development dropped abruptly in 1942, reflecting the lack of any sizable discoveries and the effect of the provisions of Federal Well Spacing Order M-68, which became effective in December 1941. In all, 1210 wells were drilled in 1942. This represents a decrease of 42.7 per cent from the 1941 total of 2110. Of the total wells completed, 553 (45.7 per cent) were oil wells with an average initial production of 443 bbl.; 102 (8.4 per cent) were gas wells with an average initial of 3,359,000 cu. ft.; and 555 (45.9 per cent) were dry. Although the number of completions declined sharply, the total of 320 wildcats completed (26.4 per cent of all wells) repre-sents a decrease of only 2.7 per cent from the previous year&apos;s figure of 329. Of the wildcats drilled, 44 (13.8 per cent) were oil wells, 13 (4.0 per cent) were gas wells, and 263 (82.2 per cent) were recorded as failures. Reconditioning of wells throughout the state resulted in a total recompletion of 355 wells. Of these, 234 were oil wells with a combined initial production of 96,808 bbl., 32 were gas wells with a total initial of 381,488,000 cu. ft., and 89 were abandoned. None of the 26 pools found in 1942 has developed into a major discovery. The Pauls Valley pool, Garvin County, is the most outstanding. Since its discovery in April, 14 wells with an average initial of 1898 bbl. have produced 803,000 bbl. of 42&apos; gravity oil from the Bromide zone. Development in this pool is believed to be almost completed. Other of the more important discoveries are the East Watchorn pool, Pawnee County; Guthrie Townsite and West Navina, Logan County; Brooksville and Macomb, Pottawatomie County, and the Liberty and Northeast Lucien discoveries in Noble county. The East Watchorn pool, at the close of the year, had 14 completed oil wells with an average initial of 989 bbl. from the Wilcox sand at 3930 it.; Guthrie Townsite, one well with an initial of 840 bbl. from dolomite at 5600 It.; West Navina, six wells with an average initial of 284 bbl. in the Lay ton sand at 5050 ft., Brooksville, eight wells in the Hunton at 4800 ft. with an average initial 01 355 bbl.; Macomb, one well with an initial of 160 bbl. in the IIunton at 4700 ft.; the Liberty pool, one well with an initial of 1268 bbl. in the second Wilcox at 4500 ft., and two wells in the Tonkawa sand at 2500 ft., with an average initial of 230 bbl. In the Northeast Lucien pool, four wells were completed in the Wilcox at 5380 ft. for an average initial of 1164 bbl., and one well was completed in the Viola lime at 5255 ft. for an initial of 55 barrels.

Jan 1, 1943

By David R. Mitchell

IF you are the owner of a mine, or a mine executive, or just an ordinary miner, and have a son about to go to college, do you urge him to take up mining engineering or do you try to dissuade him from such a course? If you live in the East, or the Middle West and your interest has been in coal rather than metal mining, the chances are that your young hopeful will be urged to do almost anything else rather than follow in father&apos;s footsteps.

Jan 1, 1939

The Iron and Steel Committee of the American Institute, of mining and Metallurgical Engineers held a joint session with the American Foundrymen&apos;s Association during the Annual Meeting of the Institute in February, 1928, for the purpose of discussing blast-furnace operations and the character of pig iron and castings. Dr. Richard Moldenke presided. H.. H. Sweetser, who was named on the program as the presiding officer of the session, was unable to be present, but sent a letter in which he said: " The meeting we had here last year and the meeting held in Chicago last June showed a desire on the part of blast-furnace men and users of pig iron to get the facts regarding the influence on castings made from pig iron produced in blast furnaces under varying conditions of temperature, mixture and local furnace operations. It has been my hope that at this Round Table we might he able to formulate a series of tests that, would give us the desired information. "Several independent blast-furnace investigations have. been, and still are being, carried on in different sections of the country. The furnaces investigated include a southern furnace, a middle-west furnace, a western furnace and a Chicago district furnace. The results so far show distinct characteristics for each of the four furnaces. It is possible that a furnace in the eastern part of the United States would be different from all the others. "It is hoped that a plan of action can be worked out at your meeting today whereby the IT. S. Bureau of Mines will be able, to carry on more extensive work in connection with the research departments of the different iron and steel companies and the big consumers of pig iron. "No one group can get all of the, information but if the different investigations can be coordinated it will he possible for us to (Iran. conclusions regarding the effects of varying conditions in blast-furnace practice on the pig iron produced and the castings made there from." DISCUSSION R. Moldenke, Watehung, N. J.—I was across the -water this summer and saw some of those interested in an investigation of this kind. &apos;I&apos;hey told me that in Germany, where they had a joint committee of blast-furnace operators and foundry-

By I. W. L. Finlay, H. R. Ogden, R. Jaffee, D. J. Maykuth

Aluminum has been found to be soluble in a titanium to about 26 pct, and to raise the temperature range of transformation from a to 8. Two intermediate phoses exist in the system, a new face-centered tetragonal phase, designated as 7, which occurs between 34 and 46 pct Al, and TiAI Metallographic and X-ray diffraction data were used to determine the diagram. ALUMINUM is one of the useful alloying additions for titanium-base alloys. It is an important constituent in two commercial alloys released in 1950, one containing 4 pct A1 and 4 pct Mn, and the other containing 3 pct A1 and 5 pct Cr as the metallic alloy content. It is probable that, in the future, other titanium alloys containing aluminum will be released. In the course of alloy development work, some of the features of the constitution of titanium-rich Ti-A1 alloys have been developed. These are described in the present paper. The only available information on the Ti-A1 system concerns the aluminum-rich end of the diagram. In summarizing the early work, Hansen&apos; indicated that there is little solubility of titanium in aluminum, and that a two-phase region exists up to the intermediate compound, TiA1a (37.2 wt pct Ti), which has a congruent melting point at 1355°C. Fink&apos; has reported that a peritectic reaction occurs at 665°C between the melt and TiA1³ to form the terminal solid solution of titanium in aluminum. The solubility of titanium in aluminum has been established at 0.24 pct at 510°C and is estimated to be between 1 and 1.5 pct at the peritectic temperature. No information has been published on the diagram above TiAl,, other than a statement- hat aluminum raises the a to ß transformation temperature of titanium. Materials and Preparation of Alloys Iodide-type titanium and high-purity aluminum were used in this investigation. Typical analyses of these materials are given in Table 1. Alloys were prepared by arc melting on a water-cooled copper hearth, using the techniques described previously for contamination-free melting.&apos; Weight losses during melting were very low, ranging from 0 to 0.02 g in a 10 to 15 g charge, indicating that little or no loss of aluminum occurred during melting. This permitted the use of nominal compositions for these alloys. Alloy ingots containing from 0 to 7.5 pct A1 were rolled in air at 850°C to 0.040 in. sheet. Alloys containing from 7.5 to 16 pct A1 could only be rolled about 25 pct reduction at temperatures up to and including 1200°C. Alloys containing above 16 pct A1

Jan 1, 1952