Search Documents

By T. H. Ramsey, Richard Shield

A process has been developed for fabricating thin-film resistors that are compatible with integrated circuits. Films are produced by evaporation of single refractory metals using an electron beam heating source. Resistor paths are then made using standard photoresist etching techniques. A low-temperature coefficient of resistance is obtained by control of nucleation during deposition of the film. One application of the process has been the development of a discrete resistor used for current setting in linear integrated circuits. Multiple thin-film resistors were formed on oxidized silicon substrates using molybdenum metal as a source. An evaporated protective layer of SiO2 over the resistor prevents resistance changes which might occur during subsequent high-temperature processing. Properties of a typical resistor are as follows: R = 15.7 ohm per sq, tolerance surface dimensions = 0.028 by 0.028 in., stable after 4000 hr at 0. 75 w without heat sink. THIN-FILM resistors have been investigated for many years with a large selection of usable resistors resulting from a wide variety of materials. Many of the processes necessitate a high degree of complexity but in nearly all cases the conclusions have been that the materials used in each case were acceptable provided the deposition process was reproducible and could be controlled sufficiently to give the required tolerances. It is our opinion that simplicity is still the key to thin-film resistor fabrication. In this regard, the single metal is obviously the simplest process to control, provided all the necessary properties can be obtained. The idea is not original in this laboratory by any means. Others have taken this approach.' It has been demonstrated that a fairly wide range of resistivities can be obtained by careful control of deposition parameters for any given metal, and by selection of several single metals a very broad range of stable resistors can be obtained. The transition from one metal to the next is made when a film becomes too thin for adequate process control or long-term stability. A great deal of emphasis is once again being placed on the thin-film resistor. Although they have been thoroughly studied in the past, new applications have been found that require the properties obtainable only from thin-film resistors. Integrated circuits, in general, are advancing toward higher speeds and radiation environments which require replacement of the present diffused resistors. Linear circuits in particular are requiring high-power, high-precision resistors for the more advanced applications. The particular requirements of some linear circuits are such that a discrete resistor is required. The resistor described in this paper was developed as a 15.7-ohm precision discrete resistor for use in a current regulating circuit requiring a +2 pct end of life overall tolerance, a dissipation of 750 mw, and the ability to operate over a fairly broad temperature range (i.e., a low temperature coefficient of resistance, TCR). State-of-the-art integrated circuit and silicon processing technology lends itself well to the fabrication of thin-film resistors. Not only is the resistor thin film well-suited to integration on individual circuits, but the oxidized silicon surface provides one of

Jan 1, 1969

By Rudolph G. Wuerker

THE scarcity of values of tensile strength of rocks has been explained by the lack of successful testing procedures. In the case of mine rock a description is given' of the difficulties encountered in testing a cylindrical specimen, such as a core, by conventional methods. Over a period of years the following method has given definite and reproducible results with the weakest as well as with the strongest rocks. It does not completely supersede the use of cores with special fixtures but is a supplement in all cases where cores cannot be obtained, as from soft rocks, or in cases where it is less expensive to prepare test specimens by cutting them out of the rock instead of drilling cores. Principle and equipment are the same as for the test for tensile strength of hydraulic-cement mortar.' The test specimen, Fig. 1, has the shape of a briquet. While in the original cement mortar test the briquet is cast in a special mold, it is prepared from rocks in different ways, depending on how easily they can be cut and shaped. Soft rocks, which cannot be core-drilled with a carboloy or diamond bit, are simply hand-cut. Only two dimensions need be watched. The first is the 1-in. diam at the narrowest cross-section of the briquet. The other critical measure is the radius of curvature of the waistline, as the roller supports in the grips have a fixed distance. This radius is ground out of the solid by means of a carborundum grinding wheel having a 3/4-in. radius. Medium hard rocks can be core-drilled with a carboloy bit. The resulting core can be used for nondestructive sonic testing first, and after that for any destructive test. By using an EX-bit and by carefully placing the coreholes, preferably by using a tenplate such as shown in Fig. 1, it is possible to obtain from the rock a punched sample from which numerous tensile briquets can be made. The outside radius of the EX-bit differs from the radius of curvature of the briquet by 1/8 in., but this still permits placing and aligning the specimen in the grips. In the case of bedded rocks the core might have bedding planes normal to the plane of the briquets, and rocks can be tested in any arrangement of the bedding planes desired. Hard rocks, limestones, igneous, and metamor-whic rocks can only be diamond-drilled or diamond-cut. Here the method of getting the tension briquets by accurate placing of EX-drill holes is especially economical. The tops of the briquets made from hard rocks cannot be rounded; they are straight cuts made with a diamond cut-off saw and rounded off on a polishing wheel. Results: As long as specimens broke over the waistline the results were considered acceptable. Further statistical treatment of the tests' showed a satisfactory percentage of standard deviation. The tensile strength values obtained by this method do not represent true values because of the stress concentration caused by the curvature of the side of the piece and because of the closeness of the grips. The ratio of maximum to average stress at the plane of failure has been determined to be about 1.75." All tensile strength values listed in Table I are corrected accordingly. To avoid this stress-concentration, if there are a sufficient number of cores, tensile strength can be measured by imbedding the cores in mortar in the two outer briquets in the gangmold.4 Strain-Measurements: The applicability of the briquet specimens for strain observations was tested in the case of sandstone and shale. Two element Rosette SR-4 strain gages were used. Young's modulus and Poisson's ratio, both in tension, were computed and found to be different from those in compression, determined during the same test series and from the same rock, see Table I. References 1 L. Obert, S. L. Windes. and W. I. Duvall: Standardized Tests for Determining the Physical Properties of Mine Rock. U. S. Bur. Mines R.I. 3891 (1946). 2 Test for Tensile Strength of Hydraulic-Cement Mortar, ASTM Standard C 190-44. S F. O. Auderegg, R. Weller, and B. Fried: Tension Specimen Shape and Apparent Strength. Proc. ASTM 11939) 39, pp. 1261-1269. 4 API Code 32.

Jan 1, 1956

By Thomas V. Falkie, Robert Stefanko

Higher education is in serious trouble in the United States. With increasing costs threatening to create a taxpayer's revolt, serious thought must be given to determining whether or not we can continue to afford our present educational policies. Disinterested students with little aptitude are pushed into over- crowded universities by well-meaning parents, but they lack real objectives beyond achieving that great status symbol-the degree. Advanced degrees are heaped upon the baccalaureate degree, and the pursuit of the pure and social sciences continues at the expense of engineering and technology.

Jan 1, 1971

By E. Topuz, S. S. Bhamidipati, M. Bartkoski

Air Leakage in underground mines is the most common cause of inefficient distribution of ventilating air. Depending upon various factors, more than one half of the fresh air entering a mine short-circuits to the return airways before reaching the working faces. Consequently, large leakages create an additional demand for increased intake air, which substantially affects the efficiency of a mine system. This paper deals with the identification of the physical variables of air leakages and offers an overview of the methods of measuring leakage.

Jan 1, 1982

By S. Robinson Brainard

In 1957 the pay of chief executives in the nonferrous metals industry was well above average when compared with other major industries. Furthermore, it continued to rise last year while sales declined 8.2 pct and profits plummeted 32.7 pct on the average. Compensation of Chief Executives: One of the primary objectives of the survey is to measure year-to-year changes in top-management total compensation as it relates to company size and industry characteristics. Total compensation includes salary, bonuses, and the value of deferred contingent compensation awards.

Jan 10, 1958

By Richard H. Terhune

Slag and matte, in lead and copper smelting, are, for convenience of removal, tapped into pots of small capacity, usually of paraboloid form, of cast-iron, weighing 275 to 300 pounds, and holding the same weight of slag. As in many smelting districts one ton of ore makes a ton and a quarter of slag, a large number of pots is needed to equip an ordinary plant. Sudden and frequent expansion of the solid bowl causes the pots to crack at the bottom in a few months, and the matte, a very fluid sulpliide, enters these rough fissures and speedily corrodes its way through the vessel. 1 find, from one year of practice with a slag-

Jan 1, 1887

By Louis A. Panek

Rock-mass fracturing was measured on oriented drill core and along scanlines in three mines extracting mineralized porphyry deposits. Fracture families identified in the core were consistent with those found along scanlines, but fracture frequency in the core was twice that measured along scanlines. The excess fractures, which occur within 45º of a right angle to the core, apparently are produced during drilling, which implies that fracture spacing in drill core is an ambiguous quantity dependent on the drilling procedures, on the orientation and cohesion of the planes of weakness, and on the actual fractures present in the rock mass.

Jan 1, 1984

By D. L. Martin

THAT small amounts of impurities have a harm-J- ful effect on the malleability of metals and alloys is well-known. One common type of em-brittlement involves the formation of a small quantity of eutectic at the grain boundaries, and is typified by sulfur embrittlement of nickel. Another example of eutectic embrittlement—sulfur embrittlement of cobalt—is described in this report. In the preparation of specimens for a study of Co-Pt alloys, it was observed that the hot swagabil-ity of the alloys appeared to be influenced by the grade of cobalt used as melting stock. The cause of the hot-shortness was not traced to any particular impurity, although sulfur was suspected.' The damaging action of sulfur on the malleability of cobalt has not been generally recognized,'; in spite of the fact that the Co-S phase diagram8 eveals the same basic conditions—low solubility and eutectic formation—responsible for sulfur embrittlement of iron and nickel.7, 8 Apparently sulfur embrittlement has not been a serious problem in the fabrication of cobalt alloys. One related factor is likely the limited commercial experience with high cobalt alloys, since the predominant use of cobalt has been in alloys containing less than 75 pet Co. A series of Co-S alloys was prepared and studied to establish the effect of sulfur on the hot working characteristics of cobalt. Specimens, 5/8 in. diam by 4 in. long, were prepared by vacuum melting in magnesium oxide crucibles and casting in a copper mold. Two grades of low sulfur electrolytic cobalt were used as the basic material for the study, one from Johnson, Matthey and Co. and the other from the International Nickel Co. Each contained about 99.5 pet Co and had a nominal sulfur content under 0.005 pet. The sulfur was added initially as cobalt sulfide powder. Later, some low sulfur alloys were prepared by diluting the high sulfur alloys with cobalt. Trouble was experienced in controlling the sulfur content. Apparently much of the cobalt sulfide powder was lost during melting, as most of the samples contained a lower sulfur content than was added. The alloys were evaluated for hot brittleness by heating to 1000°C in a hydrogen furnace and swaging in air. The results of these tests are summarized in Table I. All the alloys containing less than 0.008 pet S were successfully hot swaged to 1/4 in. diam. The bars containing more than 0.015 pet S could not be swaged because of the formation of intercrystal-line cracks similar to those illustrated in Fig. 1. Examination of the microstructure of the cast bars revealed cobalt sulfide eutectic at the grain boundaries, Fig. 2. The sulfide was not always continuous at grain boundaries in bars that were hot embrittled but, in general, the particles did form a network that could account for the brittleness above the eutectic temperature, 880°C. There is no question about the brittle nature of a specimen exhibiting a continuous sulfide network such as is shown in Fig. 2b, though a sulfide distribution similar to that in Fig. 2a is marginal. This particular bar cracked when hot-swaged. However, other bars with lower sulfur content but with some sulfide phase at grain boundaries were successfully worked. The reduction of area of a hot tensile test specimen was also found to be a sensitive indicator of sulfur embrittlement. The variation of reduction of area with sulfur content is shown in Fig. 3 for specimens fractured at 900°C in an evacuated capsule. The ductility of cobalt is greatly reduced when the sulfur content exceeds 0.005 pet. Similar results were obtained for alloys tested at 800°C, below the eutectic temperature. The upper sulfur embrittlement limit of 0.015 pet, Table I, agrees with the observation of Kalmus8 hat

Jan 1, 1957

By Maxwell Adams

CONSIDERABLE interest has recently been developed in sage-brush oil because of its possible utilization as a flotation agent in the mining industry. A list of some of its physical properties, together with the method used in its extraction, may prove of interest at this time. Something over a year ago, a study of the essential oils in desert plants was begun in the Chemical Laboratory of the University of Nevada. None of the oils so far studied possess properties of special interest to engineers, except the oil of sage, Artemesia tridentate, which has exceptional power as a flotation agent. This plant, known as common sage brush, also called black sage, is widely distributed over the semi-arid West, being found quite generally on most of the dry plains and mountains west of Missouri. The method of extracting the oil followed in these experiments is very simple. The leaves, twigs and small branches are placed in an airtight drum, having a capacity of about 27 cu. ft. Steam is admitted through a number of small openings at the bottom of the retort, and the pressure maintained at 20 to 25 lb. per sq. in. for 3 hr. The escape of the steam from the retort is regulated by allowing it to pass through a stop-cock into a condenser. The water in the receiver is drawn off from time to time and the oil, which is insoluble and floats upon the water, is thus collected. At the end of 2 hr. most of the oil has been driven out, though traces continue to come over for a much longer time. By raising the pressure, the time required could probably be shortened and the yield increased, but the lack of laboratory equipment has prevented the carrying out of this experiment.

Jan 9, 1916

By A. J. Opinsky

MANY investigators, in their discussions, have reasoned that the ductile-brittle transition in iron could be explained by the intrusion of cleavage into the normal slip process. The purpose of this note is to apply the laws of critical normal stress for cleavage and critical shear stress for slip to explain the orientation and temperature dependence of the ductile-brittle transition in body-centered cubic metals. It will be found that within a certain temperature range, single crystals tested in tension will cleave or slip, depending on their orientation. Some data recently appearing in the literature will be analyzed from this standpoint. For a single crystal with [uvw] parallel to the tensile axis, the resolved shear stress on the slip

Jan 1, 1954

By James T. B. Ives

The variety of copper-ore to which these notes refer is cornparatively rare, and, so far as I am aware, has not been recorded hitherto as occurring in Ontario. Moreover, the rocks of this locality differ so much in nature and mode of occurrence from the orebearing rocks of the western United States, that a description of them may be interesting. A line drawn upon a map of the region of the great lakes from the mouth of the Severn river at the Southern end of Georgian Bay, following the Canadian shore northwestward, and leaving Manitoulin island to the south, will describe the boundary between the Archaean rocks lying north of it and the Silurian rocks southward.

Jan 1, 1890

By David B. Reger

The value of carbon ratios in determining the boundaries of possible oil deposits appears to have passed the hypothetical stage. The theory that the ratio of fixed carbon in pure coals is an invariable index of incipient metamorphism in both surface and underground rocks and that it may be applied in defining the limits of petroleum, advanced by David White,' has been received with keen interest by many petroleum geologists. Detailed isocarb maps have been prepared of the Pennsylvanian area of North Texas and Eastern Oklahoma by M. L. Fuller.² A similar map of the coal-bearing area of West Virginia is given here. An isocarb3 is a line showing an equal fixed-carbon percentage, pure coal basis; the term has been proposed by David White to supersede a less expressive nomenclature. The term carbon ratio is applied to the pereentage of carbon in pure coal after water and ash have been eliminated. As a comparatively small number of analyses have been made on this basis, it is usually necessary to compute the ratio by dividing the fixed carbon of the proximate analysis by the sum of the fixed carbon and volatile matter of the same analysis. Many thousands of proximate analyses have been made by the West Virginia Geological Survey, covering nearly every county in which coal is found. Numerous others have been made by the U. S. Geological Survey and the U. S. Bureau of Mines, but as uniformity of results is best secured by adhering to one set of analyses, the tests of the West Virginia Survey have been cxclusively used.

Jan 1, 1921

By R. V. Riley

IN the metallographic examination of the alloys of iron and silicon, several investigators1-' have reported on the occurrence of an unusual type of etched structure, particularly in the alloys of higher silicon content. This, the so-called "barley shell" structure, has been observed with iron-silicon alloys over a wide range of silicon content, and under certain circumstances it can be seen upon the micro-sections of pure iron. The barley shell structure may be demonstrated most easily with iron-silicon alloys in the range 8 to 20 pct Si after etching in a hydrofluoric acid base etchant. Two etchants which produce the structure are: Corson's reagent, which is 2 parts hydrofluoric acid, 1 part nitric acid, and 2 parts glycerol; and picric acid reagent, which is 1 part hydrofluoric acid and 1 part saturated solution of picric acid in alcohol. Both when freshly prepared and used for etching commercial silicon-iron alloys containing 14 to 16 pct Si, invariably produce the barley shell structure shown in Fig. la. It is now well known that the barley shell structure is a pseudomorph and the true structure of an alloy of this composition consists of a single phase of silico-ferrite together with graphite as shown in Fig. lb. Lower silicon alloys and even pure electrolytic iron may also be etched in the above reagents to give the barley shell provided the etchant has been either: 1—Stored in contact with glass or silica, or 2—used previously for etching an iron containing silicon. Pure iron etched in perfectly pure hydrofluoric acid base etchants free from silicon contamination gives a normal structure free from the barley shells. Therefore, although the hydrofluoric acid in the reagent primarily is responsible for the barley shells, silicon, or its compounds, also must be present, either in the etching reagent or in the specimen. It was of considerable interest to the author to read the paper by Wachtell,? in which the barley shell etch was deliberately used for the identification of the boundaries of high and low silicon areas in diffusion experiments made upon laminate bars of compacted and sintered pure iron and ferrosili-con powders. This method of utilizing the barley shell etch is novel and in the hands of the investigator gave a useful differentiation between the high and low silicon areas in those specimens. For the reasons already given, however, the technique is not to be regarded as of universal application. Misleading results might be obtained, for example, if two or more specimens were etched in the same etchant. Fresh pure reagents only must be used each time. Provided this is done and the investigators are well aware of the limitations of the method, then the barley shell pseudomorph can be made of limited use in distinguishing between higher and lower silicon areas in a microspecimen of a ferrous material. The greatest of care must be exercised in the interpretation of the results which may be regarded as qualitative only and may, in fact, not be specific to silicon alloys.

Jan 1, 1952

WE, the undersigned, being all persons of full age and citizens of the United States and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 5 of Article I of said law, the existing unincorporated association known as American Institute of Mining and Metallurgical Engineers, Incorporated, do hereby make, acknowledge and file this Certificate for that purpose, and do certify as follows I That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained

Jan 1, 1952

By Werner Langguth

SINCE the introduction of the improved method of precipitating gold from chlorine solution by SO2 and H2S at the Golden Reward chlorination-works, Deadwood, S. D.,* this modern method has been further adopted in the chlorination-works of the Portland Consolidated Company at Deadwood, and in those of the Black Hills Milling and Smelting Company at Rapid City, S. D. It has proved practically most successful in the handling of large quantities of gold solution, and constitutes up to date, with Mr. John E. Rothwell's most important improvement, namely, barrel-leaching under hydraulic pressure, the principal progress made in gold chlorination. The method of refining the gold sulphides which result from this method of precipitation, was introduced by me in 1890 at the Golden Reward works, and in 1892 at those of the Black Hills Company. It has not suffered any changes during the last three years, and is substantially as described below:

Jan 1, 1895

CERTIFICATE OF INCORPORATION [AMENDED Nov 22, 1912, AND JUNE 27, 1919 ] WE the undersigned, being all persons of full age and citizens of the United States, and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 5 of Article I of said law, the existing unincoiporated association known as American Institute of Mining Engineers, do hereby make, acknowledge and file this Certificate for that purpose, and do Certify as follows I That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained II That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council, that the undersigned are all members of said Council as the same was constituted on the 29th day of December, 1904

Jan 1, 1923

By Earl Greiner

THE constitution of the iron-silicon alloys containing from 14 to 33.4 weight per cent silicon has been studied by a number of investigators, whose results have been reviewed in a monograph published by the Engineering Foundation1. In these previous researches, the solubility of silicon in iron was determined by thermal, microscopic or magnetic methods and the compound Fe3Si2 was reported to be stable at tempera-tures from 0 to approximately 1030° C. This paper describes the results of an X-ray investigation of the solubility of silicon in iron and gives data which prove that the Fe3Si2 phase is unstable below 825° C. In order to obtain the present results on the solubility of silicon in iron, the authors have utilized the lattice constants of the alpha-phase iron-silicon alloys given in a previous publication2, and also some addi-tional data which will subsequently be described.

Jan 1, 1936

By K. Robert Dorman, F. Michael Jenkins

The occurrence of rock bursts in deep metal/nonmetal mines presents a major hazard to their safe and economical operation. As part of a Bureau of Mines program to reduce rock bursts in deep vein mining, a project was conducted in the Coeur d'Alene Mining District of Idaho to evaluate and demonstrate the mining of a destressed sill pillar using undercut-and-fill methods. A 50-ft sill pillar in a burst-prone area was preconditioned by drilling and blasting vertical holes in the ore. After raises were driven through the destressed pillar to the level above, it was mined by the undercut-and-fill method. The conclusion from this demonstration is that the combination of ore preconditioning and underhand mining resulted in greatly improved rock burst and ground control, allowing safe and efficient mining of a potentially hazardous, burst-prone pillar.

Jan 1, 1984

By Gloyd Wiles

THE eastern section of the Park City dis-trict is drained to an elevation of 6300 ft. by means of the Ontario drain tunnel owned and maintained by Park Utah Consolidated Mines Co. This elevation represents a depth of 920 ft. in Park City Consolidated Mines Company's property. When development below the goo-ft. level was commenced, sinking was at-tempted through an incline winze in the fissure. The intensely fractured quartzite forming the walls of the vein could not be held after water was encountered, so it was decided that further sinking should be done in a vertical winze far enough in the foot-wall to be in the more solid quartzite out-side the fractured zone containing the vein. Progress was good until a depth of 200 ft. below water table was reached, where the flow of water became serious. Sinking pro-gressed 300 ft., to the 1200-ft. level, and there approximately 750 gal. of water per minute was being pumped. The last 20 ft, of sinking cost more than $200 per foot direct charges, whereas the over-all cost for the 300 ft. was $100 per foot. This high last cost was caused by excessive lost time in pumping. Crosscutting to the vein disclosed the fact that the 1050-ft. level had been devel-oped only after drainage had been effected from the 1200-ft. level, but that the 1200-ft. level could not be opened because of the

Jan 1, 1940

By E. J. Hammer

Crushing and grinding of gypsum demands con- trolled processing to a fineness suitable for further treatment of the mineral into end products, and into various sizes of material which are themselves saleable products. The majority of gypsum tonnage ultimately ends up in stucco for wallboard. Therefore, mineral reduction is normally designed toward this end, but it is done in a manner that permits drawing off intermediate products to meet various customer requirements. This forces companies into compromises at times in equipment installations. Normally, 5 to 6 different sizes intermediate to the end product are marketed and these are generally the fineness of material to be used as stucco for wallboard. These sizes are produced by controlled crushing, grinding and sizing. How Ore Characteristics Guide Processing First, gypsum as a mineral (CaS0;2H,O) is number two on the Mohs scale two of hardness; only talc is softer, Despite being soft, gypsum is tough, a factor which is of critical importance when developing equipment specifications. In addition, of the increasing volumes of rock handled, the associated and included impurities such as anhydrite, silica or lime- stones are found to be relatively abrasive.

Jan 1, 1970