Search Documents

[University of Alabama University, Alabama Mining and Metallurgical Society (Inactive) University of Arizona Tucson, Arizona Miners' Society ROBERT HIGH, President RICHARD FLAGG, Secretary J. B. CUNNINGHAM, Faculty Sponsor Birmingham-Southern College Birmingham, Alabama Geology Journal Club (Inactive)]

Jan 1, 1946

By Roswell Johnson

THE principle of sliding or graduation in royalties is accomplished either by the block, period, cumulative, or class method. The block method calls for a very low royalty rate on all oil produced up to. a certain amount. This amount would normally be that which is believed to suffice to repay the cost of the well. A higher rate would be charged after the well is making a profit. This method, common in many industries, is peculiarly inadaptable to any industry such as this where the productivity per day of the units gradually and inevitably decreases. This, for reasons given later, is because it forces an early abandonment of the well and so offends against conservation. In the period method, the royalty rate is changed by some definite amount when the well produces less than a specified quantity per day or other given unit of time. While simple to explain, it operates badly because a great deal is made to depend upon a small reduction in production, whereas the reduction as a matter of fact declines rather erratically owing to the exigency of lease management, connecting of tankage, and vagaries of the gaugers. These disadvantages are obviated by the cumulative method. In this method, all the production less than a certain amount per week has one rate of royalty, or none at all, and the oil produced in excess of that amount pays an additional rate of royalty. In the long run the calculation is probably no greater than with the period method, for simple tables will be published and printed in the oil papers that can be cut out, enabling quick readings to be made. Even without the table the calculation is easy with the few royalty rates, two or three, which would be used. In this method, the amount paid in royalty declines gradually, rather than suddenly as in the period method.

Jan 6, 1915

By G. A. Yuko, J. W. Barton, J. G. Parr

ALTHOUGH previous work1 has shown the compo- sition range of the complex face-centered cubic phase,2 Ti2Ni, to be narrow, no precise limits were established. The purpose of this investigation was to prepare homogeneous alloys on either side of the stoichio-

Jan 1, 1959

Jan 1, 1944

Most of the production of germanium in the U. S. is from byproducts of smelting Tri-state zinc ore. Only in England has commercial manufacture been reported from coal.

Jan 1, 1953

By D. G. Oss, S. E. Erickson

An automatic control method for the ferrosilicon heavy media process maintains media density within 0.01 specific gravity points. Continued demands for higher grade, competitive products from the Mesabi Range have resulted in experimental work such as that detailed for one concentrator. Various methods, step by step procedures and instruments used at an iron ore beneficiation plant in the development of an automatic control system are described. Work continues and it is hoped that further applications of control instrumentation can be made in the next operating season. The need for instrumentation and automatic control of the various parameters in the heavy media process of iron ore beneficiation has been apparent for some time. Continued demands for higher grade, competitive products from the Mesabi Range have made it necessary to increase the efficiency of the process in every possible way. In a typical heavy media flow scheme for iron ore beneficiation (Fig. 1) a sized, prepared feed (generally about —1% in. to +% in.) is fed to a heavy media separatory vessel, along with a ferrosilicon slurry. A separation of the feed is made on the basis of specific gravity. Low density particles overflow a tailings discharge weir, while high density ore particles sink to the bottom of the high density pool and are moved away to the concentrate discharge chute. Both products are passed over drainage screens and then are cleaned thoroughly of attached ferrosilicon on wash screens. Float material is generally stockpiled, while the sink product is shipped as a final concentrate. Undersize from the drain screens is returned directly to the circulating media sump. Wash screen undersize is cleaned of contaminating ore particles and slimes by passing through magnetic separators. Provision is also made for splitting a portion of the tailings drain undersize into the cleaning circuit if necessary for control of depth of tailings overflow, or for additional cleaning as required. Cleaned ferrosilicon is stored in a densifier and returned to the Circulating media sump as make-up material. Dilution water is also added to this sump to maintain a desired specific gravity of the circulating media. As in any process, operational intelligence is secured only by keeping records of the process variables. Generally apeaking, plant operators have neither the inclination nor the time to keep complete and detailed records of these variables over the course of their shift. Before instrumentation was added to aid the operator, specific gravity was measured by weighing a given volume of pulp at intervals of from 30 to 60 min. Scale readings were made at the beginning and end of each shift. No records were kept of operating conditions, such as rpm of the separatory ves-sel, media level in the machine, tons per hour of the products, and so forth. These items were recorded only when spot checks were made by the metallurgical staff. CONTlNlJOUS DENSITY RECORDING The first process instrument used, other than the usual ammeter on the drive motor of the separatory vessel, was a nuclear density gauge and its associated circular chart recorder. These instruments were used to indicate and record specific gravity of the circulating media. This was a tremendous aid to the operator in that tie was able to observe and correct the specific gravity at any time. There was also added incentive to make frequent corrections because of the permanent record made by the recorder of the densities. The addition of the nuclear density gauge was influential in securing optimum quality and recovery of the heavy media product. Manual control was improved, and it became possible for a good operator to main control within f.05 specific gravity units. This compares with an unknown quantity, estimated at f0.15 gravity units, when manual measurement and control was used. An example of the improvement in manual control over the course of one season's operations is shown in Fig. 2. Chart A is typical of the records made shortly after the gauge was installed. Needless to say, it was difficult for operators and foremen alike

Jan 1, 1962

Discussion of the paper of F. E. Lucas, presented at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912, pp. 1315 to 1326. F. Louis GRAMMER, Leesburg, Va. (communication to the Secretary *):--Mr. Lucas's paper reminds us of our extravagance in coking, and our tardiness in the adoption of by-product ovens, as compared to Germany. We are, however, so rich in coal-having mined, so far, less than 1 per cent. of our known national resources-that the argument of conservation is not very pressing. It is true that our so-called coking-coal beds are not inexhaustible; but by-product ovens coke coal that bee-hive ovens cannot handle, and so really enlarge our reserves of coking coal. " Conservation of Resources " is a phrase in great vogue. It is overworked and abused at times; being used by those who desire to be the exclusive custodians of resources or the sole purveyors of commodities. It does not carry great weight as regards coal. There are, however, aside from the attractive considerations of profit set forth by Mr. Lucas, several other important reasons why by-product ovens should be introduced more widely. One is that coal-tar pitch is the keynote to the extension of the coal-briquette industry. The more coal-tar pitch is available, the more briquetting will be carried on; and this will utilize much coal which is either waste or a drug in the market. Heretofore, in several instances coking and steel-making plants have been built, primarily, to market bituminous slack.

Jan 5, 1913

Discussion of the paper of F. M. Simonds and E. Z. Burns, presented at the New York Meeting, February, 1913, and printed in Bulletin No. 75, March, 1913, pp. 369 to 402. W. L. SAUNDERS, New York,. N. Y.:-Mr. Burns in his native Colorado modesty has said that he apologizes for things left out of this paper. I am much impressed by what he has put into the paper, as of all the papers that I have read on the subject, describing, as it does, a specific piece of work that has been accomplished, I do not recall one that gives so much information in such a practical way. Mr. Burns has also said that it is very hard to get men to put things down while the work is being driven. My experience is that it is very much harder to get the men in charge of work of this kind to bring them in in the form of a report before a body of engineers after the work is done. We have a great many cases where records are kept in much detail, but they are usually kept under cover, with the mistaken idea that the information gained is private information for the benefit of those who have done the work. Messrs. Simonds and Burns have opened up this case so that we can get the benefit of that experience which they have had, and so that we can learn something for the future. The description contained in this paper, as I have said, is a very practical one. You will notice in going through it. that the authors have given in detail a record of their work from the beginning to the end, and they even go so far as to publish an exact copy of the Rawley Mining Co.'s daily report. That daily report is something which those of us who are engaged in similar work might copy to great advantage, and having it before us we can check up our men while doing work and exact from them equal conditions, if it is possible to do so.

Jan 5, 1913

By Walter S. Landis

The earliest example of attempting to form finely-divided materials into larger masses for better adaptation to commercial use mas probably the briquetting of peat and lignite-waste at Paris by the use of a clay binder. It was from this attempt that our word briquette has arisen (Fr. la brique), the formed masses being shaped similar to ordinary bricks. This term does not, however, lend itself to the many shapes of such formed material as are now being produced, as few of them, aside from some of the European brown-coal products, bear any resemblance to the shape of that well-known article. The

Jan 1, 1913

By Charles W. Wagner

A premature explosion might be described as an explosion that, occurs before the miner expects it. Notwithstanding that it is unexpected, a premature is generally within the miner's control. A hangfire explosion is a blast that occurs after the miner expects it,, and in all instances, except where the explosives or blasting accessories are defective, hangfire explosions are within the miner's control. Causes of Premature Explosions Generally, there are seven methods of shot-firing in anthracit,e mines; namely: (1) cap and fuse with dynamite, (2) fuse with pellet powder, (3) squib with black powder or pellets, (4) exploders and delays with dynamite or black powder, (5) exploders with dynamite, (6) delay ignitors with black powder or pellets, (7) electric squibs with black powder or pellets. Cap and Fuse.—This method of firing seems to produce the greatest number of premature explosions. This is not solely because of the method, but is the result of mispractices which are possible with this method of firing. The two most common mispractices followed with cap-and-fuse blasting are the firing of multiple holes and the use of short fuse.. In the firing of multiple holes by cap and fuse, investigations have shown that in nearly every instance where the miner was injured by this method of firing he remained too long at the face lighting the several fuses, so that the first shot went off before he could reach a place of safety. Such accidents could have been avoided either by accurate judgment by the miner of the relative lengths of the fuses or by the use of electric firing. Rules exist in nearly every mine forbidding the lighting of more than one hole at a time where the cap-and-fuse method of firing is practiced. Where it is desirable to fire more than one hole at a, time, electric firing should be used. It is difficult to understand why so many premature explosions result from the use of short fuses, inasmuch as the cost of fuse is practically a negligible item in the expense of a day's work. Notwithstanding this, however, we frequently find miners using short lengths of fuse in an effort to save one or two cents per hole, or about 15 to 20 # in a day. A practice

Jan 1, 1931

By R. E. Reed-Hill, W. H. Hartt

The second order, {1011}-{1012} twin bands observed in critically deformed magnesium are often accompanied by an unusual form of kinking. These kinks, which lie adjacent to and run more or less parallel to the twin band habit, allow plastic deformation that occurs inside the twins to be accommodated into the matrix. The bend planes of these kinks cannot be explained using slip dislocations with Burgers vectors lying in the basal plane. A mechanism involving a single set of {1012)(1011) dislocations is proposed to account for the kink band habit, in good agreement with the experimental observations. It has been shown that second order, {101l)-{1012} twinning is an important phenomenon for magnesium deformed in the ambient temperature range. A detailed study of these twins has recently led to a better understanding of their irrational habit plane1 and their relation to fracture in magnesium.' This paper is concerned with a third aspect of these twins; this being the kink bands, originally referred to as shear accommodation kinks,3'4 that are often induced in the adjacent matrix. A twin band and its shear accommodation kink usually appear as a single macroscopic deformation, as seen in Fig. 1. The complex nature of these deformed regions is easily revealed, however, with the aid of a suitable microscope. It has been proposed374 that the primary function of these kinks is to accommodate the nonhomogeneous deformation that normally occurs in the second order twins. The twins tend to form as small discrete lamellae lined up approximately one in front of the other.''' Very large plastic deformations varying in magnitude from one twin to the next, may occur inside these lamellae. The kinks serve both to pass this strain into the matrix and to accommodate strain variations between twins. Deformation within the kinks, subsequent to their formation, has also been observed;3,4 and it is thought that this contributes to the strain accommodation process. The bend planes of the kinks have a habit near that of the twin band itself, which lies about 56 deg from the matrix basal plane. This orientation does not bisect the angle formed between the basal plane to either side of the bend plane and therefore differs markedly from the kink structure usually observed in hcp metals.'-' The present paper reports the results of a study of shear accommodation kinks and proposes a possible solution to the problem of the orientation of the bend plane. EXPERIMENTAL PROCEDURE Rectangular cross-section tensile specimens with axes parallel to (1010) and faces to (1210) and (0001) were cut and acid machined from a high-purity magnesium single crystal. After straining on an Instron machine the specimens were examined by both optical and replica electron microscopy. The basic procedures have been previously reported."' EXPERIMENTAL RESULTS AND DISCUSSION Structure of Shear Accommodation Kinks. A typical, large (101l)-{1012) twin band with its associated shear accommodation kink is shown running diagonally from upper left to lower right in Fig. 1. In this optical micrograph the twin band, consisting of a row of small, highly deformed twin lamellae, is visible as a narrow dark band along the left hand edge of the structure in question. The kink lies to the right of the twins, is approximately three times as wide, and is lighter in contrast. The horizontal slip lines visible on the general specimen surface correspond to matrix basal slip and are parallel to the tensile axis. Note that on the right-hand side of the band these slip lines can be followed from the matrix into the kink. At the kink band boundary the slip lines suffer a clockwise rotation of about 25 deg. Rotations of this magnitude are not uncommon. When a surface such as that in Fig. 1 is given an etch1 making it sensitive to polarized light, it has been observed that the slip traces in the kink are parallel to the basal plane trace in this region. This is in excellent agreement with the assumption that these regions are indeed kinks. Fig. 2 is an electron micrograph of this same twin band and kink. Note that a row of small supplimation pits has formed

Jan 1, 1969

By Ralph Nichols

THE mines are near the town of Gilmore, in the Texas mining district. This district was organized in 1880. The present producing mines are near the terminus of the Gilmore & Pittsburg railroad. This railroad connects with the main line of the Oregon Short Line at Armstead, Mont. The distance from Gilmore to Armstead is 70 miles. The town of Gilmore is near the head of the Lemhi river at an elevation of 7,000 ft., while the mines are from 400 to 1,300 ft. higher. The range of mountains upon which the mines are situated forms the water shed for the Little Lost river on the west and the, Lemhi river on the east. The winters are severe and the snow fall is heavy, but the mines ship right through the year. There is an abundance of timber suitable for all mining purposes in the immediate vicinity. Water is piped into the camp from a lake about 2.5 miles distant. This lake is about 1,400 ft. above the town of Gilmore. The water is exceptionally good for boiler and domestic purposes. The mining companies now producing are. the Pittsburg Idaho Co., Ltd. ; the Latest Out Mining & Smelting Co:, Ltd. ; and the Gilmore Mining Co., Ltd. Besides the above properties, there are a number .of prospects in different stages of development. The producing mines of the district are fissures in limestone, with a general northeast-southwest course .and a dip to the west of from 40° to 70°. These fissures are at about right angles to the bedding of the limestones. The veins are regular and the ore shoots strong, both laterally and in depth, so far as developed. The ore shoots have a rake or pitch to the south. The character of the formation is shown in Fig. 1, a section of the Latest Out mine.

Jan 11, 1913

By R. J. Wygal, J. Naar

An equation for three-phase (water, oil, gas) imbibition oil permeability is developed, assuming the water to be the dominant wetting fluid. Oil isoperms are obtained for consolidated sandstones characterized by 1/pc2 = CS*. The evolution of an oil-gas system imbibing water from Swi to(Sw,imb )max is shown to proceed along a line of constant oil saturation with increasing oil permeability and decreasing gas saturation. When the gas satuation cannot be reduced further, the system evolves along a line of constant Sg with decreasing oil saturation and permeability. The initial gas saturation is shown to reduce markedly the effect of complete wetting by either oil or water on flow performance. INTRODUCTION Imbibition oil isoperms are required for performance prediction when a well is producing water, oil and gas. This situation occurs in multiphase displacements such as underground combustion, steam injection and the water flooding of highly depleted reservoirs. In a recent paper,1 a model was presented for the prediction of two-phase imbibition characteristics. This paper extends the imbibition model to the case of three phases by assuming that the water is the dominant wetting fluid. The following results were obtained from the model: (1) an analytical expression of oil isoperms; (2) oil isoperrns as functions of reduced water, oil and gas saturations, valid for all sandstones having a capillary pressure curve which can be approximated by 1/PC = CS*; and (3) evaluation of the three-phase flow performance as dictated by complete wetting by either oil or water. The agreement between predicted and observed oil recovery in the presence of a gas phase, reported in Ref. 1, is a partial support for the present development. However, experimental data are not available at this time to check fully the model predictions. Perhaps this paper will stimulate the collection of such data. The imbibition model of a porous medium has been described previously, and the reader is referred to the paper of Naar and Henderson1 for details. In brief, the model is formed by the random interconnection of straight capillaries, with a provision for the blocking of the non-wetting phase by the invading wetting fluid. The following expressions were derived from the model. 1. The amount of oil blocked by the invading water is

By Henry M. Howe

The transformation which steel undergoes in slow cooling, from the condition of austenite whelk above the transformation rage into that of pearlite plus either ferrite or cementite below that range, is subject to great lag. This transformation is essentially the pearlitizing of the austenite. Indeed the hardenillg of steel is due to this lag, which is made so great by extremely rapid cooling that a very large part of the transformation itself is restrained, so that the rapid cooling catches the metal in an only partly transformed state, that of martensite, and under favorable contditions even in an almost wholly untransformed state, as in the cases of Maurer's austenitic manganese steel. Hadfield's austemtic. manganese steel, 25 per cent. nickel steel, and other anstenitic alloy steels, arc austenitic even after slow cooling. It has long been known that this lag increases (1) with the rapidity of cooling, (2) with the presence of certain retarding elements, notably manganese and nickel, and (3) with the temperature from which cooling starts. The present inquiry touches the last of these influences, but incidentally it throws light on the first also. This influence of higher heating ill increasing lag manifests itself in different ways which, though they may at first seem unrelated, are in fact hut different aspects of one and the same thing. Thus, among heatings to different high temperatures, all of them above the transformation range: the higher the temperature to which the steel is heated (1) the lower is the temperature at which the transformation occurs in cooling slowly down, (2) the shorter is the time occupied in the actual cooling from above the transformation range to the room Temperature under given external conditions, Whether of slow or

Jan 1, 1914

By T. W. Watson, D. R. Flynn

,Measurements are reported for the thermal conductivity of four heat-resistant alloys which were measured at the National Bureau of Standards. Data are given for two samples of AISI Type 316 stainless steel covering a combined temperature range from -150° to + 800°C. The thermal conductivities of three samples of AISI Type 347 were measured over the temperature range from -150° to +150C. Thermal conductivity values are given for Carpenter 20 stainless steel from 100" to 800" C. Data are given for Inconel 702, in both the solution-annealed and the age-hardened condition, over the temperature range from -150" to +800C. SINCE 1958 the National Bureau of Standards, at the request of other government agencies or private laboratories, has carried out measurements of the thermal conductivity of a number of metals and alloys. This paper presents available thermal conductivity data obtained in this way on samples of four heat-resistant alloys. The data presented for Carpenter 20* stainless steel are, to the best of our knowledge, the only thermal conductivity values which have been reported for this alloy to date. Although thermal conductivity values for AISI stainless steels 316 and 347 have been reported by previous investigators, the present data are believed to be of particular interest because, for each alloy, the effect on thermal conductivity of small changes in chemical composition can be observed. The data on Inconel 702' are of interest, not only for

Jan 1, 1969

By L. L. Hirsch, W. M. Parris, P. D. Frost

IT has been established that titanium alloys con- taining sufficient amounts of ß-stabilizing elements, such as iron, chromium, or manganese, can be age hardened.' Adenstedt, Pequignot, and Raymer2 showed that age hardening occurred in a Ti-15 pct V alloy at room temperature after it was quenched from a temperature in the ß-phase region. During a recent investigation of the heat-treating characteristics of binary Ti-Mn and Ti-Cr alloys at Battelle, further evidence of low temperature aging was found. Appreciable hardening occurred in some of these alloys at aging temperatures as low as 212 OF (100oC). Indeed, the brief heating period employed for mounting metallographic specimens in bakelite resulted in hardening. It was felt that further information on this low temperature aging phenomenon would be of general interest in view of the large amount of work currently being done on titanium alloys. The alloys examined in this investigation were arc-melted in a water-cooled copper crucible as 3/4-lb ingots. Du Pont Process A sponge was used as a base material. The arc-melted ingots were forged at 1700" to 1800°F (927" to 982°C) and hot rolled at 1450°F (788°C) to 14 gage (0.064 in.) sheet. Small specimens were heated in argon at 1742°F (950°C) for 30 min and quenched in various liquid media or air cooled. They were then mounted in a room-temperature-setting resin and given a metallographic

Jan 1, 1954

By S. B. Sargent, V. J. Collins, Lester C. Uren

[The conclusions arrived at by authors in paper read before the Petroleum Division and the California Sections of the Americam Institute of Mining and MetallurgicaI Engineers and the Standardization Division of the American Petroleum Tnstitute, at a joint session held at Los Angeles, Cal., Jan. 21, 1926, are presented below.] From the theoretical discussion and experimental evidence presented in this paper, the following conclusions may be drawn: 1. The efficiency of the oil-well plunger pump is dependent to an important degree upon the submergence provided. 2. Ample submergence must be secured in order to provide sufficient static pressure to force the oil through the restrictions interposed in the oil path at the standing valve and at the plunger nut surrounding the garbutt rod. These restrictions should be no smaller than is structurally necessary, in order to reduce resistance to oil flow to a minimum. 3. A part of the static pressure developed below the standing valve by submerging the pump is dissipated in overcoming the inertia and in providing upward acceleration for oil left between the pump valves at the conclusion of the down-stroke of the plunger, and of oil below the standing valve in the gas anchor above the oil inlet. This loss in effective static pressure can be reduced to a minimum by dispensing with the garbutt rod and placing the working valve at the lower end of the plunger. The valves should be as near together at the conclusion of the down-stroke of the plunger as is consistent with security in avoiding striking of the lower end of the plunger on the standing-valve crown. Gas anchors should be short, and oil inlets should be as near the standing valve as is consistent with proper gas exclusion. 4. Because of the presence of gas in solution in the oil, which tends to escape from solution under the reduced pressure conditions above the standing valve, the effective length of stroke of the plunger is reduced, and the suction effect of the rising plunger is largely nullified. The influx of oil through the standing valve is therefore chiefly dependent on static pressure developed by submergence.

Jan 1, 1927

By S. G. Malghan, J. P. Van Dillen

Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined.

Jan 1, 1984

By C. B. Thwing

IT is likely that among most races, owing to the ease of finding and working clay, the making of clay utensils was learned earlier than the molding of metal implements. The ancients made good pottery and durable brick in kilns that wasted fully one-half the heat and spoiled fully one-fourth of the ware; and, taking the clayworking industry as a whole, we are doing the same today. The chemical and physical changes involved in the burning of clay are so many and vary so much with the composition of the clay that it is not surprising that the rule-of-thumb methods so commonly employed fail to give uniform results. In its passage from plastic clay to the vitreous or stonelike character the mingled minerals and accidental organic impurities of which the clay is blended must pass through four stages, the second and third usually overlapping, and the fourth often beginning before the third is complete. These stages in their order with the rising temperature are drying, dehydration, oxidation, vitrification. In the first part of the drying stage, usually accomplished in part outside the kiln, the water mixed with clay is dried out at temperatures not much exceeding the boiling point of water. In the later part of this stage, within the kiln, the hygroscopic water, absorbed from the air is expelled at somewhat higher temperatures, this stage being known as watersmoking. Some clays are very sensitive to temperature during the drying stage and if the temperature exceeds 100°, the ware becomes checked. Other clays may be dried more rapidly without danger. In down-draft kilns, the draft is slight during the watersmoking stage and the water driven off from the top rows condenses on the ware in the bottom of the kiln, with the result that high temperatures are likely to be reached at the top of the kiln before the bottom is fully dry. The lag in temperature of the bottom persists to the second stage in spite of the better draft then prevailing.

Jan 9, 1919

Duval Corporation, the copper -producing subsidiary of Pennzoil United, Incorporated, operates two plants south of Tucson, Arizona: Esperanza and Sierrita. The newest, the Sierrita mine and mill, came into full production in 1971 at a rate of 72,000 tpd (now 87,000 tpd) which at that time made it the largest designed copper plant in the world. In 1968, the largest milling units then available were selected; these included fourteen 16$ ft by 19 ft long ball mills (5 m by 5. 9 m), each equipped with a 3,000 hp motor. The primary crushing plant contains two 60 in. by 89 in. Allis- Chalmers gyratories; each is constructed for two-side dumping by 120- and 150-ton trucks. Access to the maintenance areas to service the drive motors, eccentrics, apron feeders, and speedup conveyor is through hatches between the crushers. This area also contains a good- sized elevator and a stairway. The rather shallow dump pocket, the 300 -ton crushed ore pocket, and the overall design make for a fine, compact arrangement for two 60 in. crushers installed in a total height of 89 ft (27. 13 m) from dump level to top-of-concrete at the lowest level beneath the collecting or speedup belt. This efficient layout is reflected in the short changeout time for mantle and concaves (8 and 30 hours respectively) and the low crushing cost of $0.0416 per ton (first half of 1975). The crushers are installed on 64 ft (19.5 m) centers (Bougainville and Palabora, both with 54 in. crushers, are 55 and 43 ft or 16.76 and 13. 1 m respectively). The switchgear room is located between the truck dumping positions on one side of the installation and the hydroset units on the other side, with dust collecting equipment mounted over the latter. Protection of these units from rocks falling from the trucks is provided by concrete walls. Truck dumping is controlled from a central 25 ft high (7.6 m) control room, which permits fine observation of operations. Removal of oversize boulders from the dump pockets is done with a hydraulic grapple or a rock hook or sling attached to the auxiliary crane hook. Spare mantle stands and a maintenance room with a zinc melting furnace are located at one end of the surface facilities. The maintenance room is equipped with an access door for the crane, which is equipped with 80- and 20-ton hoists. The two 84 in. (2. 135 m) apron feeders receiving the 6 in. (152 mm) crushed rock discharge onto a 72 in. (1. 83 m) collecting and wear belt operated at a speed compatible with the 60 in. (1.524 m) takeaway belt running at a speed of 630 fpm (192 mpm). This belt feeds a 54 in.

Jan 1, 1978