Search Documents

By Mowry Bates

THE following example of the practical application of engineering geology is of interest in that it demonstrates the advantage of keeping accurate records of all wells, whether drilled by one's self or by others, together with the advantage gained by gathering such data during the process of development. The fault described was found in the autumn of 1915, during the hurried development caused by the discovery of the famous Gusher Bend pool in Red River Parish, Louisiana. The writer was at the time employed by one of the operating companies as geologist, and the example is a portion of the routine work. LOCATION The oil fields of northern Louisiana and east Texas are located in Caddo, Bossier, De Soto and Red River Parishes, Louisiana, and Marion County, Texas. A very narrow strip of the eastern portion of the latter is productive. The producing oil pools are known as the Caddo Field, in the northern part, and the De Soto-Red River Field, in the southern. The two fields are 60 miles apart. There are several gas fields between then, but no important supply of oil has been found, though there are several producing wells in the Anona chalk, locally called the chalk rock, in the Elm Grove gas field in Township 16 North, Range 11 West (see Plate 1).

Jan 5, 1918

By Robert Gilman Brown

There are few disasters so difficult to deal with as an underground fire. It is inaccessible at best, and generally unapproachable ; and it finds most material in the very places where it can do most harm, namely, in large stopes and in " heavy " ground where timbers are massed, and in shafts and level-stations where there are inevitably strong drafts to make the burning yet more fierce. The fire constituting the subject of this note occurred in the shaft of the Standard mine at Bodie, California, and originated after the departure of the night-force at 3 a.m., being discovered by the men going to work at 6.30. At that time it had gained already considerable headway, and was throwing smoke plentifully from the collar of the shaft. It must be premised, for understanding of the situation, that in this shaft all hoisting is done to the 320-foot level, where the material is dropped by chutes 30 feet. to the tunnel-level, through which it is run to the mill. Hoist and sheaves are all placed

Jan 1, 1897

By S. V. Krishnan, I. Iwasaki

In the upgrading of finely disseminated iron ores, selective desliming is the critical step that must be controlled to achieve efficient flotation. A prerequisite for selective desliming is a properly-dispersed pulp; sodium silicate is commonly used as a dispersant. The mechanism by which sodium silicate acts as a dispersant in the presence of calcium ions was examined by streaming potential measurements, settling tests, abstraction density determinations, selective flocculation tests, and scanning electron microscope observations. The study established that calcium silicate precipitates on the mineral surfaces dispersed the pulp. Although sodium silicate was a nonselective dispersant, the addition of corn starch aided flocculation of goethite over quartz at low silicate additions, but became ineffective at higher silicate levels. A model is presented to explain the dispersant mechanism of sodium silicate in the presence of calcium ion for selective flocculation of iron ores.

Jan 1, 1983

By B. T. Wykoff

This paper describes an important function of mining in Southeast Missouri. The practice is a necessary procedure to prevent disintegration of the pillars. Although the technique is peculiar to this district, it might have application in other mines using room and pillar method.

Jan 8, 1950

By Andrew Allen

WHEN a mine is changed from hand, to me-chanical loading, the character of the coal dumped at the tipple is changed in many ways. Selective mining is not so easy with mechanical load-ers, and where much picking is done at the face it is apt to be wasteful anyway. Much recoverable coal is apt to be lost by too free gobbing and, in my opinion, picking at the face should be confined to removal of heavy rock, such as pieces of roof or bottom or sulfur balls. and to such clearly defined and persistent bands as can be readily recognized and segregated. With mechanical loaders of the shovel type, even this amount of gobbing is almost impossible. When coal is shoveled into a conveyor there should be no difficulty in doing as much picking as now by hand loading. The size of lumps may be greatly increased, on ac-count of the ease of handling them with a shovel, as the miners will not break them up in order to lift them into cars. Fines may be increased. This is, of course, not universally true, yet it is my opinion that a shovel breaks the coal more, as a rule, than hand loading. This might not be true with all types of shovels and is cer-tainly not true with a conveyor, either with or without the "duck-bill." The average car load will be greatly reduced in fields such as Illinois and Indiana, in which it is the practice to build up the coal above the sides. Where "level full" regulations prevail there should be no material change. When the coal comes to the tipple these differences usually result in the discovery, that many changes are necessary in the preparation plant. The increase in the percentage of fine sizes will probably not bother the screen, but may overload the conveying apparatus. The larger size lump may clog the chute, but as a rule the efficiency of the sizing screens is not greatly affected. In one completely mechanized mine the proportions of 6-in. lump and 2-in. screenings, when loading by hand, were 16.9 and 51.3 per cent respectively. When loading mechanically, these proportions changed to 15 per cent lump and 53.5 per cent screenings. The picking force on the tipple has been increased from 14 on hand loading to 33 men on mechanically-loaded coal. This is for an output of about 5000 tons.

Jan 4, 1927

By L. F. Reinartz

The furnace in which rimming steel is made has an important bearing on the quality of the steel produced. Furnace.—Particularly in the manufacture of low-carbon rimming steels, it is necessary to have an efficient, easily regulated furnace, because of the relatively high finishing temperature requirements. In recent years, the most important development in design of open-hearth furnaces has been the sealing and insulation of the greater part of the furnace to prevent air infiltration and loss of heat. Efficient, straight-line valves insure proper draft. Combustion controls guarantee correct gas-air ratios. Furnaces of all sizes ranging from 20 to 200 tons have been used successfully in the manufacture of rimming steels. Metal bath is varied from 20 to 40 in. in depth without appreciable variation in quality. Charging.—A normal open-hearth charge consists of pig iron (hot or cold), scrap of miscellaneous nature, and slag-making additions, such as limestone and burnt lime. Because of local conditions, some plants find it necessary to discard the use of pig iron and use some carbonaceolis substances with varying percentages of cast iron to replace the pig iron. It is questionable whether such practice will consistently produce the quality of rimming steel required for auto stampings and other severe drawing requirements. Pig Iron.—An open-hearth furnace under proper control should melt 150 tons of low-carbon rimming steel on about 35 to 38 per cent pig-iron charge basis. In some practices, best results are obtained when the total charge contains from 0.40 to' 0.50 per cent silicon. If reasonably low-

Jan 1, 1935

By L. F. Reinartz

The furnace in which rimming steel is made has an important bearing on the quality of the steel produced. Furnace.—Particularly in the manufacture of low-carbon rimming steels, it is necessary to have an efficient, easily regulated furnace, because of the relatively high finishing temperature requirements. In recent years, the most important development in design of open-hearth furnaces has been the sealing and insulation of the greater part of the furnace to prevent air infiltration and loss of heat. Efficient, straight-line valves insure proper draft. Combustion controls guarantee correct gas-air ratios. Furnaces of all sizes ranging from 20 to 200 tons have been used successfully in the manufacture of rimming steels. Metal bath is varied from 20 to 40 in. in depth without appreciable variation in quality. Charging.—A normal open-hearth charge consists of pig iron (hot or cold), scrap of miscellaneous nature, and slag-making additions, such as limestone and burnt lime. Because of local conditions, some plants find it necessary to discard the use of pig iron and use some carbonaceolis substances with varying percentages of cast iron to replace the pig iron. It is questionable whether such practice will consistently produce the quality of rimming steel required for auto stampings and other severe drawing requirements. Pig Iron.—An open-hearth furnace under proper control should melt 150 tons of low-carbon rimming steel on about 35 to 38 per cent pig-iron charge basis. In some practices, best results are obtained when the total charge contains from 0.40 to' 0.50 per cent silicon. If reasonably low-

Jan 1, 1935

By H. T. Byck

The plastering properties of six representative California drilling muds were studied over a temperature range of 70 to 175 F. at several mud weights, using a high-pressure circulating filter press with full size consolidated cores. In all tests, with untreated as well as with chemically treated muds, the filtration rates at elevated temperature were higher than at low temperatures and in nearly every case this increased filtration rate was notably larger than could be attributed alone to the decreased viscosity of water—the flowing medium—at elevated temperatures. It is concluded that no existing method will permit even an approximate determination of the filtration rate at high temperature from data at room temperature. It is necessary to measure filtration at the temperature actually anticipated in the well, or to make a sufficient number of tests at various lower temperatures so that a small extrapolation of these data to the anticipated well temperature may be applied. Such tests should be carried out on the mud as actually used in the well. The viscosity of each of the muds was determined over the same temperature range. While no relationship was observed between mud viscosity and plastering properties, it was found that chemical treatment of the muds for viscosity reduction shifted the temperature of minimum viscosity to appreciably higher values than for untreated muds. Importance of Plastering Properties A survey of the literature on rotary drilling muds clearly shows the growing realization of the importance of plastering properties,'-5 not only from the point of view of the successful completion of the mechanical operation of drilling the well but also from the point of view of minimum impairment of the natural flow possibilities of a given well. Poor plastering properties with attendant high filtration rate (large water loss to the formation) and thick mud sheath, lead to stuck drill

Jan 1, 1940

By H. T. Byck

The plastering properties of six representative California drilling muds were studied over a temperature range of 70 to 175 F. at several mud weights, using a high-pressure circulating filter press with full size consolidated cores. In all tests, with untreated as well as with chemically treated muds, the filtration rates at elevated temperature were higher than at low temperatures and in nearly every case this increased filtration rate was notably larger than could be attributed alone to the decreased viscosity of water—the flowing medium—at elevated temperatures. It is concluded that no existing method will permit even an approximate determination of the filtration rate at high temperature from data at room temperature. It is necessary to measure filtration at the temperature actually anticipated in the well, or to make a sufficient number of tests at various lower temperatures so that a small extrapolation of these data to the anticipated well temperature may be applied. Such tests should be carried out on the mud as actually used in the well. The viscosity of each of the muds was determined over the same temperature range. While no relationship was observed between mud viscosity and plastering properties, it was found that chemical treatment of the muds for viscosity reduction shifted the temperature of minimum viscosity to appreciably higher values than for untreated muds. Importance of Plastering Properties A survey of the literature on rotary drilling muds clearly shows the growing realization of the importance of plastering properties,'-5 not only from the point of view of the successful completion of the mechanical operation of drilling the well but also from the point of view of minimum impairment of the natural flow possibilities of a given well. Poor plastering properties with attendant high filtration rate (large water loss to the formation) and thick mud sheath, lead to stuck drill

Jan 1, 1940

By Ruder, W. E.

CONSIDERABLE interest has been shown lately in various types of furnaces for the production of high, temperatures, both for laboratory purposes and for small industrial uses. Dr. J. A. Harker1 described certain modifications of the Arsem graphite resistance helix for high-temperature work at the National Physical Laboratory. Dr. Northrup ,also has developed two interesting forms of high-temperature furnaces. In 1911, Messrs. Winne and Dantsizen2 described two forms, of resistance furnaces using ductile molybdenum or tungsten as resistors. Since the discovery, by this laboratory, of methods for producing these metals in ductile form, their use as resistance elements in the research laboratory of the General Electric Co. has grown to such an extent that they are now almost indispensable. These furnaces are used here for alloy research, annealing, heat-treating, and practically all f the thermal processes requiring temperatures above 900° C. Various types of furnaces have been developed to meet the general needs of laboratory work, and it is the purpose of this paper briefly to describe some of these furnaces. A tubular furnace wound with a metallic resistor is the simplest type to construct, and almost every laboratory has made such furnaces. The only essential difference between a furnace wound with platinum or base metal and one wound with tungsten or molybdenum is that the coils of the latter must be heated in a neutral or reducing atmosphere. It has long been our custom here to build our resistance furnaces with a metallic casing from which the tube could be easily removed for rewinding. The heat-insulating material-usually calcined magnesia, alumina, silica, or silex, depending upon the nature of the resistor-is used in powdered form so that it can he readily removed and replaced. In order to adapt this method to tungsten or molybdenum windings, it

Jan 2, 1918

By Chairman Hill H. H.

The Round Table Discussion on Petroleum Engineering Research was planned for two purposes. First, to review the work that has been done by petroleum engineers during the past few years on problems that have confronted the industry and, second, to suggest new studies that should be made either on the problems that have been the subject of research during the past or on problems that have arisen only recently. It was believed that by holding an informal discussion of the problems in which the petroleum engineer is vitally interested it would be possible to bring out new ideas as to the relative importance of the different problems that should be studied and to suggest new methods for attacking some of the problems that have resisted the energies of research workers throughout the industry. It was also believed that by arranging for an exchange of experiences between the different engineers it would be possible to prevent a large amount of duplication of effort in conducting research work. Those engaged in petroleum engineering research realize that there is a broad field for study and by coordinating the work it will be possible to obtain the maximum amount of information in the shortest possible time. In planning the program on Petroleum Engineering Research, nine subjects were selected for discussion and each was assigned to a man who is doing work on that subject. These men were asked to lead the discussion on the problem assigned to each one. An effort was made to choose problems of a practical nature and upon which considerable work is being conducted at the present time. Some of the men who were asked to lead the discussion were unable to attend the meeting but most of them submitted a written discussion- of the subject assigned, with the result that there was a discussion of eight of the nine problems. Professor Uren, who was asked to lead the discussion on the subject of Recent Developments in Methods for Reducing Gas-oil Ratios, was unable to attend the meeting and advised that he did not have any new ideas to contribute.

Jan 1, 1928

By Eric Jette

IN a recent article,1 the authors reported the results of an X-ray investigation on the range of solid solutions that occurs in the iron-oxygen system in the vicinity of the compound FeO, which frequently is called "Wüstite." The object of that investigation was primarily to study the unusual type of solid solution phenomena involved in this range. Briefly summarized the results were: 1. The NaCl type of lattice found by earlier workers was confirmed. 2. The lattice dimensions decrease rapidly with decrease in iron content. 3. No alloy that was a homogeneous single phase was ever found at compositions beyond 76.80 per cent Fe, while the theoretical iron content of FeO is 77.73 per cent Fe. 4. Measurements of the densities and lattice constants led to the conclusion that the form of substitution was complex, an FeO group being replaced by oxygen. Such a substitution, of course, is equivalent to removing an iron atom (or ion). The ideal unit cell of FeO can be con-sidered as containing four groups of FeO and, thus, when this type of substitution takes place, there remain in the unit cell three FeO groups and an oxygen, or a total of seven atoms with a gross formula of Fe304 instead of the original Fe404. 5. This was the only interpretation that would fit the experimental results and at the same time be consistent with (a) the previously deter-mined fact that the FeO lattice is ionic (i. e., consists of Fe++ and 0= ions) and (b) the chemical fact that as the oxygen content of the substance increases, ferrous iron becomes oxidized to ferric iron. The experimental results of this investigation are included in Fig. 1.

Jan 1, 1933

By B. S. Lement

No appreciable stabilization of the austenite-martensite reaction occurs in a 15 pct Cr-0.7 pct C steel unless some martensite is initially present. Stabilization is induced by interrupting the subcool below M,; however, disappearance of the stabilization effect as manifest by burst formation of martensite may occur on continued holding at the final subzero reaction temperature. The higher the temperature of intermediate cycling after the initial subcool, the more permanent is the stabilization effect at the final reaction temperature. Appreciable conditioning of retained austenite occurs on reheating to about 500°C. These phenomena are explainable on the basis of the reaction-path theory. A RECENT investigation' carried out by the authors has shown that isothermal transformation of austenite to martensite definitely takes place in a 15 pct Cr-0.7 pct C steel and that appreciable amounts of martensite can form in this fashion. Investigations2-" arried out on other steels and iron alloys make it seem probable that isothermal formation of martensite is a phenomenon of fairly general occurrence. The reaction-path theory of Cohen, Machlin, and Paranjpe5,7 explains isothermal transformation on the basis of thermal activation of strain embryos which generate martensite plates with a velocity approaching that of sound. On the other hand, the nucleation and growth theory of Fisher, Hollo-mon, and Turnbull8 egards isothermal transformation as due to growth of athermally formed martensite nuclei. The experimental evidence obtained thus far favors the reaction-path theory in that the martensite reaction seems to be nu-cleation-controlled rather than growth-controlled. Stabilization is another phenomenon of importance with respect to the austenite-martensite reaction. According to the reaction-path theory, stabilization is a result of relaxation of strain embryos. It is postulated that strain embryos are present at the austenitizing temperature in the form of dislocations or lattice imperfections in the austenite which vary in the extent to which the lattice is displaced along the strain reaction path leading to martensite. On quenching from the austenitizing temperature, athermal martensite starts to form as soon as the M. is reached, because the activation energy of the transformation which decreases with decreasing temperature is lowered to below the level of the highest energy strain embryos. Martensite plates are generated during the cooling below M, from embryos possessing energies above the activation energy corresponding to the temperature at which the cooling is stopped. The distribution of lower energy embryos is changed because of the elastic and plastic strains produced in the remaining austenite as a result of the transformation. This effectively increases the number of strain embryos at all levels of energy below the activation energy and tends to stimulate further martensite formation either iso-thermally or on subsequent cooling. However, if the temperature at which the cooling is stopped is high enough for relaxation of strain embryos to occur, some degree of stabilization against further transformation may be induced. Whether stabilization will be observed on subsequent cooling will depend on the extent of decrease of activation energy with temperature. If the activation energy decreases sharply with temperature, it is possible that transformation will appear to continue with decrease in temperature in spite of the loss of embryos by relaxation. However, with a more gradual decrease in activation energy, stabilization will be manifest by no further transformation on cooling over a measurable temperature range until the

Jan 1, 1954

By Frank Firmstone

By C. M. Young

BITUMINOUS coal piled in heaps or bins frequently undergoes a process of spontaneous heating as the result of the absorption of oxygen. It seems probable that the first absorption of oxygen by coal which has not previously been exposed to the air may occur as a condensation or a combination of oxygen in some form which does not result in the production of carbon dioxide, but slow combustion soon begins. The absorption of oxygen is accompanied by an increase of temperature, and this by in increased rapidity of absorption; hence the dangerous condition proceeds from bad to worse, until the kindling point is reached, unless the process is interrupted. A dangerous rise of temperature can be prevented by excluding oxygen, by increasing the bulk of coal in proportion to its surface exposed, or by circulating enough air to dissipate the heat produced. The storage of coal, in practice, varies from almost complete exclusion of oxygen, by storing under water, to such freedom of access as exists when the coal is stored in open piles. Oxygen available for absorption by coal is supplied by the air in the interstices between lumps and by additional air which may enter the pile through circulation. The size, of the coal largely affects both of these supplies; for if the fragments a re small the spaces between them constitute a small percentage of the total volume, and little oxygen will be available unless the circulation of air brings in a fresh supply, while with large fragments the percentage is relatively large; circulation also is much easier through a pile of coarse lumps. In the case f lump coal, although a large amount of air may be present, the exposed surface is comparatively small and there is little opportunity for the absorption of oxygen to so rapid as to cause dangerous heating. Attempts have been made to prevent heating by allowing a sufficient circulation of air to carry off the heat generated; obviously this method cannot be applied to fine sizes nor mixed sizes.

Jan 2, 1918

By S. R. Mitchell, M. C. Fuerstenau, A. M. Gaudin

The two principal attributes of a thickener pulp are its settling rate and the ultimate pulp density of the thickened mud. Testing for evaluation of thickening attributes of a pulp has usually been done batch-wise by placing the pulp in a one-liter glass graduated cylinder and noting the position of the boundary between clear liquor and mud as a function of time. Refinements in testing have included repulping a thickened mud to various dilutions and evaluating the settling rate on these various repulped muds. This is considered to make possible an estimate of the settling rate as a function of pulp density and therefore to pinpoint the slowest settling pulp which ought to be critical from the standpoint of thickener plant design. Finally, tests are sometimes made with model-size continuous thickeners of arbitrary size. In batch tests it is generally accepted that the behavior of a pulp is described by a curve such as the one shown in Fig. 1, in which the position of the boundary between clear liquor and mud (the mudline) is plotted against time. It has also been assumed that the initial settling rate (the slope of the line segment AB) is descriptive of the pulp and independent of the size and shape of the container. Where the settling rate is slower and clearly a function of time (portion CD of the settling curve), it has been assumed that the data are not of much use because of the intrusion of compacting phenomena. The next important datum is the height. PE, which is a measure of the so-called ultimate pulp density. This quantity is assumed to be characteristic of the pulp and independent of the container. When actual data are recorded, results are rarely exactly according to this theory and numerous deviations may be noted. For example, some pulps seem to require an appreciable delay before beginning to settle, as in line AF. This is spoken of as representing the need for an induction time for flocculation. It has seemed desirable to explore thickener data with a more sensitive charting tool than is afforded by the coordinates of Fig. 1. Instead of relating the position of the mudline to time, it has seemed desirable to relate the rate of descent of the mudline to time. This, in effect, amounts to charting the slope of the line in Fig. 1, or the derivative of its ordinates, against the same abscissas. Fig. 2 shows the new chart for the curve ABCDE of Fig. 1. When this new tool was applied to data obtained, for example, with sized clay pulps, astonishing differences appeared. Apparently the traditional tool conceals differences instead of revealing them, whereas the new method emphasizes them. It seems, also, that both charting methods have their uses. In this article attention is focused on the effects of pulp density and container height as they affect the settling behavior of flocculated suspensions of a sized kaolin. The thesis by M. C. Fuerstenau' gives more details than this summary, as well as some information about the effect of other variables. Sized fractions of kaolin were used, supplied through the courtesy of S. C. Lyons of the Georgia Kaolin Co. Large batches were made by agitation in a flotation machine and in a glass jar equipped with a mixer. The settling vessels were 2, 4, and 6-in. diam glass cylinders of various heights. Pulp Dilution: The effects of pulp dilution on sedimentation behavior are shown in Figs. 3, 4, and 5. Fig. 3 shows data on pulps ranging from 2.44 to 16.7 pct solids initial pulp density, flocculated with Separan and charted in the traditional manner. At least two of the lines appear nearly straight in their early sections, but neither of the others does. Each of the curves in this figure includes a region labeled

Jan 1, 1960

By Jamie Deuel

The a ad on Connection" For the purpose of this paper, we will concentrate on the ubquitous radon gas as the principle, low-level radiation effect from uranium tailings piles. Standards are also proposed for gamma radiations but, by most accounts, this is much less of a low level problem than is radon. I am also aware of some just completed research at Oak Ridge National Laboratories that suggest polonium may be a major concern in tailings, but those data are preliminary at this time. What is radon gas? In the first place it is not a gas in the accepted sense in that it has no driving pressure head. It might prove a more convenient description to call it radon vapor. Radon vapor, then, is 7-1/2 times heavier than air. Radiologically, it is an alpha emitter which means it spontaneously gives off high ionizing potential but low penetrating power particles. In fact, the alpha particle has such low penetrating power that this sheet of paper will completely shield a person. The problem, though, is breathing the radon decay products, called radon daughters. If radon daughter products are ingested into the lungs, their alpha emissions may cause cancer. The principle carcinoma associated with breathing radon, or more basically, associated with radiological effects is oat cell car- cinoma of the undifferentiated mall cell type. Radon has a 3.8 day half life which means in less than four days half of its initial radioactivity has decayed away. In less than a month it essentially becomes inert or non-radioactive. The Tailings Situation The NRC, in its April 1979 Generic Environmental Impact Statement

Jan 1, 1983

By AIME AIME

EARLE EDWARD SCHUMACHER, the new Chairman of the Institute of Metal, Division. is well known to the metallurgical profession. His election a, Chairman is the culmination of fifteen years' service to the Institute, beginning in 1930 when he was elected Member. Since that time he has served as member of the I.M.D. Data Sheet Committee. 1935-40; Papers and Publication Committee. 1936; Executive Committee. 1937-1910: Papers and Programs Committee, 1937-1938. (Vice-Chairman, 1939-40, Chairman. 1941-12): Annual Award Committee. 194142. (Vice-Chairman, 19431: Vice-Chairman, LM.D., 1943-44; Chairman Publication Committee, 1943-44; member Powder Metallurgy Committee), 1944. Pew other men have contributed so Much time anti effort in so many way- to the interests of the metals branch o4 the A.I.M.E.

Jan 1, 1945

By C. M. Means

CONSIDERING the hazard involved in mining operations, statistics show, that a very small percentage of accidents is chargeable to electricity. These accidents do represent quite a large percentage of those that are preventable and they are the direct result of the introduction, for purely economical reasons, of a dangerous element. The introduction of electricity in mines should decrease the hazard, and in no case should electricity be applied to the mechanical operation of equipment if by so doing the dangers incidental to mining are increased. The greater number of accidents are the result of persons coming in contact with exposed conductors at potentials varying from 250 to 500 volts direct current. The use of alternating current at higher potentials than these is quite common in large mines, but it is very rare that an accident happens from this source. This is explained by the fact that where these high voltages are warranted, proper precautions are taken, and the installations are directed by those who fully appreciate the dangers incidental to the work. Direct current is in much more general use than alternating current because of its adaptability to haulage locomotives and the low cost of installation in small operations. We are, however, coming to a more extended application of alternating current for the operation of mechanical devices used in connection with mining. Our underground direct-current wiring system is an evolution from the surface trolley and feeder systems. This is probably due to the fact that our earlier successful applications were electric locomotives, which required the use of a trolley wire. The trolley current has been almost banished from industrial establishments on the surface because of the hazard involved, yet we use it indiscriminately underground, where the dangers from accidental contact or fire are infinitely greater. This does not mean that the underground trolley systems should be eliminated, but it does imply the proper safeguarding of such equipment as is necessarily a part of the trolley systems.

Jan 4, 1914

By D. C. Jones

THE term "coal-mine mechanization" is definable in several ways. In its general application it can mean the use of machines instead of manpower in each of the various mining activities necessary for the produc¬tion of coal-so that under this definition a mine that uses mechanical coal cutters could be classed as a mechanized mine. Common usage, however, insists that a mechanized mine is one in which machines are used for the entire process of mining or extraction and transportation of the coal. For the purpose of this paper, then, the second definition of "coal-mine mecha¬nization" will be used, and practices employed in mines where the greater part of the production is obtained through the use of mechanical loaders and conveyors will form the basis for this discussion. PHYSICAL CONTACT HAZARDS If we were to group all the hazards that accompany the use of mechanized equipment in a mine, the predominant class would be that which, for want of a better name, might be termed the "physical contact" hazards; that is, all the sources of danger that lead to accidents through physical contact of workmen with ma¬chines. A survey of accidents in a group of mechanized mines indicated that this class of hazards may be responsible for more than half the number of accidents in mechanized mining. For example, of 21 mining-machine accidents at one mine, 14 were of the physical contact type of 14 loading-machine accidents at the same mine, 8 were the result of physical contact. Certain of these hazards an controllable through the use of guards-¬a guard over the cutting-machine bits whet the machine is being trammed from place to place, or a chain or some similar locking device around the cutter chain, so that an accidental blow or push against the bit control will not cause the cutter chair to move. Other hazards, such as the possibility of. a loader operator having hi foot crushed by a crawler tread, or , brakeman being hit by a loader boon swung too far to one side while a car is being loaded, might be subject to control through the use of guard devices, but the reduction or elimination of all physical contact hazards by such methods doe: not appear feasible. Every accident of the physical contact type should be investigated to discover whether guards could have prevented it, but often the only way in which to combat these hazards will be through the awakened consciousness of each workman as to the danger that exists if he indulges in unsafe practices. A good approach to control of accident: in any mine is the establishment of a set o: safety rules or operating rules. The intent of such rules is to provide guides for the workmen to follow in the operation of equipment. Frequently the workmen have no regard for such rules, and observance is obtained only through compulsion or the part of management. An interesting development in connection with the formation of safety rules occurred during a training program for employees in the

Jan 1, 1946