Search Documents

By John Freeman

THE tensile properties of steels at elevated temperatures have been studied by numerous investigators,1 primarily for the purpose of determining their suitability for structural uses. Tests with this objective have been confined largely to the temperature range of approximately 20° to 500° C., because of the rapidly decreasing tensile strength at the latter temperature. Tests have also been extended to higher temperatures for the purpose of determining the most suitable forging range. This temperature range is also of theoretical interest. The phenomenon of increased tensile strength and decreased ductility in the so-called "blue-heat" range, approximately 200° to 300° C., is well known. It was suggested to the Bureau early in 1926 that a study of the properties of rail steels in this temperature range might prove of interest in relation to the studies of transverse-fissure failures in rails. There were available from another investigation3 several new rails from several different heats made to approximately the same specification requirements, the complete manufacturing histories of which were known. It was decided to determine, at least in the preliminary series of tests, only the ultimate tensile strength, elongation and reduction of area, because of the difficulty, time and cost involved in determining the proportional limit and yield point at elevated temperatures.

Jan 1, 1930

By J. T. Ryan

SAFETY practice or the elimination of accidents in our coal mines is specifically a problem of management. It cannot be delegated to any governmental agency except that the various coal-producing states do and should have some minimum safety standard laws. However, the legislative method of attempting to control mine accidents is ineffective because of the delay between the necessity and the action. It will always be impossible to keep our various state mining laws up to date; and when the law says you must do a certain thin there is a tendency to do this and no more. Unless the scheme for setting up state regulations is so flexible that when a new hazard develops it can be immediately and adequately covered and the whole responsibility for accident elimination placed undivided on the

Jan 1, 1937

By Ellsworth Daggett

THE ore smelted in the Winnamuck furnace during the year 1872 consisted, for the most part, of oxidized ores from the Winnamuck mine, only sixty tons of outside ore (from the Spanish mine) having been smelted. The latter, like the principal Winnamuck ore, was oxidized or so-called carbonate ore. There was mixed with these oxidized ores three hundred to four hundred tons, or 7 to 10 per cent. of galena, some of which was mined with the oxidized ore, while a part was mined separately from the lower portion of the mine, and afterwards mixed with the ore, with a view of preventing the formation of deposits of metallic iron in the furnaces. The average assay in silver of all the ore handled was 51.46 oz. per ton, most of it existing as chloride of silver. The lead contents were 34.98 per cent., all, or nearly all, in the form of carbonate of lead. The relative amount of silver is not at all constant, the best silver ore often being poorest in lead. The predominant gangue was silica, several determinations of which have been made on representative samples, yielding in three such samples 26, 38, and 58 per cent. silica, the latter test being ore containing but little lead. The average contents in silica are about 35 per cent., with 6 to 7 per cent. sesquioxide of iron, and small quantities of alumina and lime. Mechanically, the ore was very fine, and so thoroughly disintegrated that it presented few distin¬guishing characteristics, rendering sorting or separating of ore from waste difficult, and often impracticable. Experiments on a small scale have been tried, with a view to separate the silica by washing; but these were unsuccessful, as the finest slime, requiring a long time to settle in still water, contained a large amount of silver; and on a careful sizing and washing of the sands and coarser parts, the silver contents were found to be less dependent upon specific gravity

Jan 1, 1874

By C. W. Dunham

FOR discharging and diffusing the gases from the reverberatory furnaces and converters the Morenci Reduction Works has been provided with one of the largest reinforced concrete chimneys ever built. It is 612 ft. high from the bottom of the foundation to the cap at the top, and has a minimum diameter of 24 ft. inside the lining near the top and 38 ft. 10 in. at the bottom. Its estimated capacity, at the elevation of 4338 ft. above sea level, is about 1,000,000 cu.ft. of gas per minute at a temperature of 500° F. and an atmospheric temperature of 90°. Under these conditions the draft will be at least 3 in. of water at the flue inlet. The gases enter the chimney through a steel balloon flue 33 ft. high and 15 ft. wide, the bottom of which is 19 ft. above the ground.

Jan 1, 1942

By A. O. Dady

PRODUCERS of both bituminous and anthracite coal have for many years been worrying about the gradually decreasing consumption of their product in the United States. Twenty years ago production had climbed to a peak of 569,000,000 tons of bituminous and around 90,000,000 tons of anthracite. In 1939 it was about 393,000,000 tons of bituminous and 51,000,000 tons of anthracite. This does not mean that the country is using less polver than it did twenty years ago, or that we are living in colder buildings. As a matter of fact, about three times as much electric power is now being consumed as in 1920. In general two factors are responsible for the drop in coal consumption: (1) greater efficiency in the use of coal, and (2) increased competition from hydro power, internal-combustion engines, and substitution of oil and gas for coal in conventional furnaces. As to the first factor, it took 3 Ib. of coal to generate a kilowatt-hour of electricity in central stations in 1920 and it takes 1.4 Ib. now; it took about 175 Ib. of coal in railroad locomotives to haul 1000 long tons a mile in 1920 where it talces about 120 lb. now: and marked economies have also been made in the use of coal in steel plants: in by-product coke ovens, and in other large uses. As to the second factor, three times as much electricity is produced from water power now as was produced in 1920; three times as much oil is being consumed in various ways; and likewise, the consumption of natural gas has tripled- whereas coal consumption in the same period has dropped by 40 per cent

Jan 1, 1941

By AIME AIME

ON Thursday a most interesting symposium on "Gases in Metals" was held, with both morning and afternoon sessions. The morning was devoted principally to the considerations of the steel maker, the nonferrous field being taken up in the afternoon period. Dr. John Johnston, as chairman, introduced the subject with "A Short Analysis of the Gas-metal Problem and Its Practical Importance." He then introduced P. H. Brace who explained in considerable detail the various vacuum fusion and other methods in use at present, both here and abroad, in the study of "gases" in metals. He was fol¬lowed immediately by H. W. Graham on "The Effect of Oxygen in Steel." The papers elicited considerable discussion, the point being particularly noted by both Dr. Rawdon and Dr. Sauveur that a knowledge of "total oxygen" alone is not sufficient information for the metallurgist, distribution of oxygen being probably the more important. Dr. Johnston, in commenting on the lack of agreement among many of the methods now in use, such as the Ledebur and vacuum fusion, spoke of the contemplated plan of the Iron and Steel Division to have a number of standard samples analyzed by many laboratories by the various methods, the Bureau of Standards acting as a clearing house, so that more definite information may be obtained on the comparative accuracy of the method.

Jan 1, 1933

MEMBERS, JUNIOR MEMBERS, ASSOCIATES AND JUNIOR ASSOCIATES LIST OF MEMBERS ALPHABETICALLY ARRANGED EXPLANATION OF SYMBOLS ** Junior Member. t Associate. || Junior Associate. Members are not marked. Capital letters signify Honorary membership. Student Associate and Rocky Mountain members on pages 165-167. Abadilla. Quirico A Catanawan. Tayabas, P. I. Abbey. Robert Graham. District Mgr The W. W. Sly Mfn. Co., 60 Church St New York. N. Y. Abbott. A. N Mines Supt Mazapil Copper Co Ltd . .Conception del Oro. Zac., Mexico. Abbott. Ckrence E Mgr Mines & Quarries, Tenn. Coal. Iron & R. R. Co 1242 Brown Marx Bldg Birminrham. Ala. Abbott. Louie Benjamin. Chief Enar Consolidation Coal Co Elkhorn Div .Jenkins, KY. Abeel. Gsorge H Jr., Cons. Min. Enar .Box 427. Santa Monica. Cal. Abel. Albert E Asst. to Pres Valley Mould & Iron Corp Hubbard. Ohio. Abel. Raymond L. Asst. Prof., Dept. of Pet. Refin Univ. of Pittsburgh Pittsburgh. Pa. Abernathy. George Elmer. Prof. of Geol. & Min Kansas State Teachers College. Pittsburg. Kans. IlAbernethy. D. Carl, Jr. Min. Engr Hudson Coal Co .Scranton. Pa. Abey, Hiroshi. Min. & Met. Engr., Min. & Met. Dept., The Higher Technical School, Osaka. Japan. tAbarn, Robert H Instructor in Met Harvard University Cambridge, Mass tAbozeid,Mahmood. Pet. Production E r . . Marland Oil Co. Ponca City, Okla. Abraham. Arthur W Geol., Richfield Oil Co Box 788. Bakersfield, Cal. Abraham, W. E. V Member, Staff of Burmah Oil Co Ltd. Nyaunghla. Upper Burmz, India. Abrahams. Alexander I Gen'l Mgr., Racon Electrical Co Slough, Bucks England. tAbrahammn. C. W Min. Engr The Mond Nickel Co Ltd . Coniston, Ont Canada. IlAbmn. Guy W., Asst. Metallographist, Youngstown Sheet & Tube Co., Research Dept., Youngstown. Ohio. Abstein. Henry T., Engr. & Mgr Profile-Tamarack Mines Co . .Yellow Pine, Idaho. tAcker. E. O'C Met I28 East Washington Lane. Germantown, Philadelphia. Pa. Ackerman. D. E Met. Research Lab International Nickel Co Inc Bayonne. N. J. tAbckerman. Ernest R Pres., Lawrence Portland Cement Co . .Plainfield. Union Co N. J. ||Ackerman. George F Jr. Min. Engr El Potosi Min. Co. .Apt. 13. Chihuahua, Chih Mexico. Acres, T. H Geol. Dept Valuation & Pet. Engr., Richfield Oil Co. 655 S. Flower St Los Angeles. Cal. Adachi. Jinzoo Address Wanted. Adair. Arthur C Valuation Enar., Internal Revenue. Treasury Dept., Washington, D. C. Adam. John. Min. Ennr., The Zinc Corp. Ltd., Box 4 C. Broken Hill, N. S. W Australia. Adami. Arthur E V. P Montana State School of Mines.Butte, Mont. Adami. Charles J Min. Ensr St. Joseph Lead Co 4540 Lindel Blvd., St. Louis, Mo. Adams. C. W.729 South Normandie St LaGranada Apt Los Angeles, Cal. Adams. Cmyler Geerwwd. Minn. Adams. F. J Gen'l Anent. Gulf Production & Pipa Line Cos .Fort Worth. Tex. ADAMS. FRANK DAWSON. Logan Prof. of Geology and Dean, Faculty of Applied Science, McGill Univ Montreal. Que Canada. Adama, Gale L Research Enar., General Pet. Corp. of California, Higgins Bldg Los Angeles. Cal. Adams. George I, Prof. of Geol. & Mineralogy Univ. of Alabama, Tuscaloosa, Ala. Adams. H. H Cons. Geol Room 416, W. T. Waagoner Bldg Fort Worth. Tex. Adams, Henry. Cons. Min. Ennr 1050 Edgewood Ave., Plainfield, N. J. Adams, Henry H.285 Madison Ave., New York. N. Y. Adams, Henry Farnum. Engr., Charge. Experimental Work. Inspiration Concentrator, Inspiration Cons. Copper Co Box 354. Inspiration. Ariz. Adams. Huntington. Min. Enar I41 Broadway, New York. N. Y. Mama, Leland D., V. P., Leslie-California Salt Co 166 Montgomery St., San Francisco, Cal. Adams, Louis W., Illinois Steel Co .Gary. Ind.

Jan 1, 1929

By Gilbert P. Moore

The production of petroleum in Argentina during 1932 was greater than in any preceding year. The total amount produced was 13,012,-756 bbl. This figure represents a decided increase in the production of oil in Argentina and can be attributed largely to the increased activities of the Royal Dutch operations at Kilometer 27 in the Comodoro Rivadavia district and those of the Standard Oil Co. of Argentina in the Salta region. Production from the Royal Dutch wells amounted to considerably more than 10,000 bbl. per day over quite a long period during the year. Of the 13,012,756 bbl. of oil produced during 1932, the Government Agency (Y. P. F.) was responsible for some 5,578,954 bbl., while 7,433,-802 bbl. were produced by private companies. Although in 1930 the Y. P. F. produced about 55 per cent of the total production and in 1930 50 per cent of the total, in 1932 its production had fallen to about 42 1/2 per cent of the total. This decrease in the proportion produced by the Y. P. F. was not due to a decrease in its production but to the decided increase in the production of private companies, particularly those two whose names are given above. One new discovery was recorded during the year. This was a well drilled by the Y. P. F. at Cacheuta in the province of Mendoza which came in pumping 80 bbl. of 15" gravity oil from a depth of 673 meters. This well was completed at approximately the same time that the provincial government of Mendoza granted a concession to the Y. P. F. and declared the whole province as a reserve in which no concessions may be granted for a period of 10 years. Under these conditions, the federally operated Y. P. F. will have no competition in the Cacheuta area from private companies such as they have in the other three fields of the republic. The Y. P. F. wildcat west of Comodoro Rivadavia at Pampa Maria Santissima on the Rio Senguerr was completed as a dry hole during 1932. This we11 was reported as a producer in 1930 by persons returning to this country from Argentina but it appears that they had been misinformed. The site of this test has been abandoned and a new location made north of the Rio Senguerr.

Jan 1, 1933

By A. C. Dorenfeld

In most mineral enterprises, what is the progress, and shift in responsibilities, as the young engineer advances in the corporation? You are all familiar with the normal pattern-in mine production from level boss, to shift boss, to superintendent to manager; in milling from test engineer, to shift boss, to foreman, to superintendent and then manager; in engineering from surveying on to Chief Engineer; and all then aspire to the corporation presidency. Note the shift-from purely technical jobs, say in the first five to ten years in the profession, to administrative positions for 30 to 40 years. What is the average preparation given to mineral engineering students, who can look forward to about 30 years of administrative work? From the catalogs of 21 institutions, offering 36 curricula of four years length, in mining and/or metallurgy, requiring the equivalent of about 150 to 160 semesterhours for graduation, the following results were obtained: Average number of semester hours of economics, 3 hr. Range of requirements, 0 to 8 hr. Thirteen curricula do not require any economics. Accounting and business law, average: 1 semester hr, 26 curricula do not require business law or accounting.

Jan 2, 1955

By Percival Roberts

I DESIRE to present this evening a few notes from the standpoint of a manufacturer upon the subject of tests of iron for structural purposes; not that I have any new facts to which to call your attention, but rather a statement of a few of the objectionable features of the present modes of operation, showing the absolute necessity of important and very radical changes. At the present time, as most of you are well aware, proposals for materials are accompanied by certain specifications as to quality and tests to which the manufactured article must conform. Evolved in many cases from the inner consciousness of some one more expert in theory than in practice, we find a few of the specifications to be good, many bad, and some indifferent. Appended are specimens of specifications of the most prominent engineers and railroad companies, which may be taken as representing the best and most intelligently framed specifications which we now have, arid yet in some pints scarcely satisfactory, owing to misunderstanding of tests as now made. To show the very varied opinions held as to proper quality of iron for bridge-work, I give the tests of two lots of fron made by inspectors with the results, which were referred to the maker with the following commensts : Lot No. 1. Teat of Iron for Eyebars. Reduced area. Elongation. Size. Per cent. Per cent. Breaking load. 4" x 1 3/8 26 25 68,500 Bent 120° around 1 1/2" bar with fracture. Reduced area. Elongation. Size. Percent. Percent. Breaking load. 6" x 1 7/15 24 24 48,820 Bent 110° around 2" bar. This iron should bend 180° without fracture, and is therefore rejected. Lot No. 2. Test of Iron for Brirlye. All measurements taken upon a parallel section of 10". Iron for tension members. Breaking load Elongation. size. per aquare inch. Percent. 1 5/8 49,600 20 14 61,600 27

Jan 1, 1882

By F. T. Havard

(Canal Zone meeting, November, 1910.) I. INTRODUCTION. THE present truce in litigation between Western smelting and ranching interests gives opportunity for a summary of the results achieved by metallurgists in condensing fume and de-acidifying furnace-gases. In the absence of complete records of past experiments, there has been a good deal of unnecessary duplication of attempts and' failures. Yet, especially under the recent policy of our large corporations, looking to the economic recovery of the values of by- and waste products, original and, in some cases, effective measures have been developed by American metallurgists. In the case of Bliss vs. the Anaconda Copper Mining Co., the Montana Supreme Court, recognizing the progressive efforts made to render the flue-gases innocuous, and the value to the community of the smelting company's operations, refused to hamper its work, and returned a verdict in favor of the defendant. In the trial, the experimental firms of the company in the so-called "affected region" were proved to be thriving perfectly, showing that immunity was guaranteed to vegetation and stock by the wide distribution of the sulphurous acid gas in the dry air of Montana. Indeed, L. S. Austin has proved that by the time the fume is 4,000 ft.. distant from the stack, the percentage of sulphurous acid has been diminished from 2.28 to 0.00045; and Angus Smith has shown that rain must contain 40 parts per million of free acid before vegetation is affected. The arsenic in the stack-gases is but a very small part of the original content of the ore, of which 80 per cent. and over is rejected in the concentrator and furnace waste-products or recovered in the flues. Nevertheless, neither the peace in Montana nor the armistice

Aug 1, 1910

By T. F. Witherbee

Discussion of Mr. Baker's paper, read at the Lake Superior Meeting, September, 1904. MR. T. F. WITHERBEE, Durango, Mexico (communication to the Secretary*) : Mr. Baker's paper is very instructive in that it shows how furnace-derangements sometimes originate from apparently slight causes. In 1896 a similar burning through of the lining occurred at the Mayville furnace of the Northwestern Iron Co., Mayville, Wis., in exactly 38 days from the time the furnace was blown in. At that time I attributed it to the fact that the bell was carried several inches to the front side of the furnace, the length of the versed side of the arc described by the lever, thus dumping a little more of the charge on the back side, which made the front side of the furnace-charge more open and consequently increased the circulation of the furnace gases through it. After reading Mr. Baker's description, I believe that possibly a little more ore was charged on the back side of the hopper, due to the fact that it was nearest to the elevator. This unequal charging, however, was unconsciously done, as the fillers were both honest and faithful. The illustration of the burned lining of Furnace No. 1, given in Fig. - of Mr. Baker's paper answers very well for the Mayville furnace. It shows that in both cases the destruction of the lining was largely due to faulty construction, in that there were no cooling-plates in the angle of the bosh and in one or two courses of brick above it, where I believe they are-more in demand than anywhere else in the furnace. The presence of these cooling-plates at the angle of the bosh would have obliged the current of the hot gases to turn the corner and would have prevented them from following the angle of the bosh com¬pletely through the lining and shell.

Mar 1, 1905

By Francis P. Sinn

LOW prices have made 1938 a difficult year for the zinc industry of the world. Particularly in the United States, output had to be radically curtailed to bring production into line with consumption. Despite these unfavorable conditions, some additional plant construction is contemplated. In Jugoslavia, through co-operation with the Government, Trepca Mines is lo build a zinc plant to produce 10,000 metric tons annually, the plant to be ready for operation in July, 1941). Cerro de Pasco is proceeding with its plans for an electrolytic plant in Peru. A pilot plant, to be ready next summer, is under construction. In eastern Canada an electrolytic plant is planned in Quebec to treat concentrates from Yoranda and other mines but no defi-

Jan 1, 1939

By AIME AIME

APPARENTLY unperturbed by any misgiving as to ill luck connected with the mystic number thirteen -for there were exactly that number of Directors on deck-the Board held two sessions on Tuesday, Feb. 21. , . Between the executive session at 5:15 p. m. and the general session at 8:30 p. m., 28 Section and Division delegates were wests of the Directors at dinner. Committee chair- " men and past officers brought the attendance to 75. Messrs. McAuliffe, Merica, Mudd and Tally had expressed their intention to be at the Directors' meeting, but each was prevented unavoidably at the last minute. At the executive session of the Board, J. V. W. Reynders was unanimously chosen to fill the unexpired term of Dr. Becket as Director: and Eugene McAuliffe in like " manner was selected to become Vice-president to fill the vacancy created hy Dr. Becket's assumption of the Presidency. Upon nomination of President Becket the following Executive Committee was appointed: Frederick M. Becket, chairman; Howard N. Eavenson, H. A. Guess, J. V. W. Reynders and William Wraith; and the Finance Committee was appointed as follows: Henry Krumb, chairman; Paul D. Merica and H. G. Moulton. Karl Eilers was reelected Treasurer and A. B. Parsons was re- elected Secretary to serve for the ensuing year, whereupon the executive session was adjourned.

Jan 1, 1933

Sailing westward from the Society Islands in the fall of 1774, England's noted explorer Captain James Cook discovered New Caledonia-that long, linear island that has played such an important and varied role in the history of nickel. Upon his return to England the following year, Cook's announcement of this uncharted island generated governmental interest, but its distance from the Island Empire, the troubles in the colonies, and the difficulties with France combined to keep English interest indirect and in the background of the then-current events.

Jan 10, 1968

By P. G. Coombs

The kinetics of the cyclic oxidation and reduction processes for palladium powder were examined in the temperature range 848 to 923 K. The changes in oxidation behavior due to cycling are shown to result from the decrease in surface area. Sintering is found to occur only during the reduction process. Oxidation kinetics were found to follow a cubic law with time and yield a relation for the oxidation rate constant of k x = (1.05) 106 exp P74.0). 103 / RT] The kinetics of reduction are demonstrated to be first-order with the rate constant described by the expression: kr = (7.69) 1012 exp [-(208.0) 103 / RT] . In both expressions R is in J.mo1-1.K-1.

Jan 1, 1984

By Ellsworth Daggett

The ore smelted in the Winnamuck furnace during the year 1872 consisted, for the most part, of oxidized ores from the Winnamuck mine, only sixty tons of outside ore (from the Spanish mine) having been smelted. The latter, like the principal Winnamuck ore, was oxidized or so-called carbonate ore. There was mixed with these oxidized ores three hundred to four hundred tons, or 7 to 10 per cent. of galena, some of which was mined with the oxidized ore, while a part was mined separately from the lower portion of the mine, and afterwards mixed with the ore, with a view of preventing the formation of deposits of metallic iron in the furnaces. The average assay in silver of all the ore handled was 51.46 oz. per ton, most of it existing as chloride of silver. The lead contents were 34.98 per cent,, all, or nearly all, in the form of carbonate of lead. The relative amount of silver is not at all constant, the best silver ore often being poorest in lead. The predominant gangue was silica, several determinations of which have been made on representative samples, yielding in three such samples 26, 38, and 58 per cent. silica, the latter test being ore containing but little lead. The average contents in silica are about 35 per cent., with 6 to 7 per cent. sesquioxide of iron, and small quantities of alumina and lime. Mechanically, the ore was very fine, and so thoroughly disintegrated that it presented few distinguishing characteristics, rendering sorting or separating of ore from waste difficult, and often impracticable. Experiments on a small scale have been tried, with a view to separate the silica by washing; but these were unsuccessful, as the finest slime, requiring a long time to settle in still water, contained a large amount of silver; and on a careful sizing and washing of the sands and coarser parts, the silver contents were found to be less dependent upon specific gravity

By Robert B. Coleman

The recent surge in demand for uranium in the US, accompanied by a significant increase in price, has stimulated the search for and development of lower grade ore bodies. At the mill, this translates into much larger throughputs and-compounded by many recently enacted environmental considerations-has made the cost of milling a critical factor in today's uranium production economics. The three conventional milling methods employed in the extraction of uranium ores are reviewed in the following sections.

Jan 10, 1978

By W. J. Romanow

RECENT papers by Williams, Sherwood, and Boothby,1 Seybolt et al.2 Heikes; and Roberts4 attest to the increasing importance of the hexagonal ferromagnetic compound MnBi. Since the magnetic properties of MnBi crystals are highly anisotropic, it is useful and necessary to have appropriate aids for determining their orientations—a (00.1) standard stereographic projection and a corresponding table of crystallographic angles for this structure. The tables of crystallographic angles for the hexagonal system available in the literature5 are computed for c/a ratios greater than that of MnBi and cannot satisfactorily be used to find the crystallographic angles of MnBi. A table of angles between the crystallographic planes (HK.L) and (hk.1) was calculated for MnBi from the formula0 F=are cos Hh+Kk+ 1/2(Hk+hK) + 3/4 (a/c)2Ll/v(H2 + K2 + HK + 3/4 (a/c)2L2) (h2+ k2+hk + 3/4 (a/c)2l2) on an IBM Type 650 Magnetic Drum Data Processing machine. The lattice constants used are listed in Table I and are those determined by Willis and Rooksby7 at 20°C. More recently published values obtained by both X-ray and neutron diffraction"' show no difference from these significant to the calculation. From the crystallographic angles between the basal plane (00.1) and the general plane (hk.1) in Table I, an (00.1) standard stereographic projection was made for MnBi which is shown in Fig. 1. Acknowledgments The author wishes to thank R. G. Treuting and J. N. Hobstetter for their technical assistance, and Miss D. P. Booth for programing the IBM machine for the calculations. He appreciates the opportunity to read the paper of B. W. Roberts of General Electric Co. prior to its publication. References 1H. J. Williams, R. C. Sherwood, and 0. L. Boothby: Bulletin Amer. Physical Soc., 1956 vol. 1, p. 132. 2 A. U. Seybolt, H. Hangen, B. W. Roberts, and P. Yurcisin: AIME Trans., 1956, vol. 206, p. 605: Journal oF Metals, May 1956. 3R. R. Heikes: Physical Review, 1955, vol. 99, p. 446. .B. W. Roberts: A Neutron Diffraction Study of the Structures of Manganese B.W.Roberts:ANeutronDiffractionBismuthide, Physical. Review, 1956, vol. 104, p. 607. 5 A. Taylor and S. Leber: AIME Trans., 1954, vol. 200, p. 190; JouRNal of Metals February 1954. « C. S. Barrett: Structure of Metals, 2nd Ed., p. 635. McGraw-Hill Book Co. New York and London, 1952. 7B. T. M. Willis and H. P. Rooksby: Proceedings Physical Soc., London, 1954, vol. 67B, p. 290.

Jan 1, 1958

MORE than 5000 miners and suppliers descended upon Denver to make the American Mining Congress' four-day metal mining show one of the most extravagant equipment displays ever assembled in one place at one time. The most recent developments in equipment for mining, milling, and processing ore were shown by the 146 exhibitors at Denver's new City Auditorium which covers 57,000 sq ft of floor space. Other displays were placed in the open air opposite the auditorium site. Registration desks were opened Sunday, Sept. 21. A field trip to the Colorado School of Mines at Golden was the featured activity of the day. Official opening of the show took place on Monday, and presided over by Howard I. Young, president of American Zinc, Lead & Smelting Co.; Otto Herres, vice president, Combined Metals Reduction Co.; William J. Coulter, vice president, Climax Molybdenum Co.; Charles B. Stainback, Westinghouse Electric Corp.; and Merrill E. Shoup, president, Golden Cycle Corp. Convention welcoming addresses were delivered by a representative of Mayor James Q. Newton, of Denver, and Gov. Daniel V. Thorton of Colorado. Following the formal opening ceremonies a round table discussion dealt with the "Paley Commission Report" formally called Resources for Freedom. Participating in the panel were: Arthur H. Bunker and George R. Brown, members of the Paley commission; H. I. Young, president of the American Mining Congress; Horace M. Albright, president of U. S. Potash Co.; Evan Just, vice president, Cyprus Mines Corp.; Donald H. McLaughlin, president, Homestake Mining Co.; E. H. Snyder, president Combined Metals Reduction Co.; Simon D. Strauss, vice president, American Smelting & Refining Co.; Sen. H. C. Dworshak (R.-Idaho) ; Ira B. Joralemon, consulting engineer; Jess Larson, De fense Materials Procurement Agency; and Andrew Fletcher, president of St. Joseph Lead Co. The panel discussed the report for six hours, adding a great deal of information to the already voluminous amount which has been gathered concerning it. Three objections to the report frequently mentioned were: 1-the multilateral contract; 2-international buffer stocks; 3-international buffer stocks combined with limited quota arrangements. Points on which the panel commended the report were its recommendations for acceleration of topographic and geologic mapping of the United States and Alaska; recognition of the principle of percentage depletion for metals and minerals; and advocation of removal of the present limitations on the expensing of exploration costs applicable to minerals. Technical sessions were held throughout the four days of the meeting. Included in the program were: Progress in Mechanication; Small Mines; Public Lands; Open Pit Mining; Manpower-Labor Relations; Shaft Sinking; Roof Support; Taxation, Gold, Silver and Monetary Policy; Advances in Mill Practices; Special Conference on Strategic Materials; Uranium Mining-Atomic Energy; Prospecting and Exploration; New Metallurgical Processes; and Rock Breaking. About 45 papers and several panels were presented during technical sessions. Formal and informal social functions consumed the remaining time of the convention. Three locations were needed to handle the huge throng attending the Mining Jamboree Monday evening. The only other sponsored social function took place Thursday evening. A great many informal gatherings, chiefly convivial, were held in manufacturers' courtesy rooms-called wet stopes. Field trips included Cripple Creek, Pueblo, Climax -Leadville-Gilman, Colorado Plateau-Grand

Jan 1, 1952