Search Documents

By F. W. Bloecher, A. M. Gaudin

THIS paper describes the results of a series of tests carried out to determine the partition of dodecylamine between distilled water and the surface of quartz at various concentrations of dodecylamine acetate in solution. An adsorption-column technique was utilized for this purpose. Ralston and Harwood, of Armour and Co., had synthesized marked dodecylamine acetate for us.' In their preparation which we employed, 0.0007 pct of the total carbon was the radioactive isotope, carbon fourteen. Unmarked dodecylamine acetate of high purity was also prepared by them for our use. The presence of carbon fourteen in the dodecylamine enabled us to analyze quantitatively for dodecylamine on the surface of quartz, using a radioactive-tracer technique. The method used was that known as internal gas counting of carbon dioxide, formed by oxidation of the amine. This method has already been described, "3 ' and the reader is referred to these papers for details of the analytical method and procedures. and surrounding liquor, a technique analogous to chromatographic columns was utilized. The experimental setup is shown in fig. 1. The dodecylamine-acetate solution was made up in a volumetric flask and poured into the glass funnel shown. It was allowed to drip slowly onto the quartz bed, the rate of flow from the funnel reser- voir being controlled by a hose clamp. The quartz column was contained in a small, fritted-glass filter (size 20 mm, C). The beaded top edge of the filter was cut off to enable the holder and contents to fit into the open end of the 30/45 joint on the combustion tube. This combustion tube is used in the analytical train described in a previous paper.' A piece of gum-rubber tubing joins the bottom of the fritted-glass filter to a filter flask, which in turn is connected to a vacuum line, or water aspirator. The rate of flow of amine solution through the bed was

Jan 1, 1951

By F. W. Bloecher, A. M. Gaudin

THIS paper describes the results of a series of tests carried out to determine the partition of dodecylamine between distilled water and the surface of quartz at various concentrations of dodecylamine acetate in solution. An adsorption-column technique was utilized for this purpose. Ralston and Harwood, of Armour and Co., had synthesized marked dodecylamine acetate for us.' In their preparation which we employed, 0.0007 pct of the total carbon was the radioactive isotope, carbon fourteen. Unmarked dodecylamine acetate of high purity was also prepared by them for our use. The presence of carbon fourteen in the dodecylamine enabled us to analyze quantitatively for dodecylamine on the surface of quartz, using a radioactive-tracer technique. The method used was that known as internal gas counting of carbon dioxide, formed by oxidation of the amine. This method has already been described, "3 ' and the reader is referred to these papers for details of the analytical method and procedures. and surrounding liquor, a technique analogous to chromatographic columns was utilized. The experimental setup is shown in fig. 1. The dodecylamine-acetate solution was made up in a volumetric flask and poured into the glass funnel shown. It was allowed to drip slowly onto the quartz bed, the rate of flow from the funnel reser- voir being controlled by a hose clamp. The quartz column was contained in a small, fritted-glass filter (size 20 mm, C). The beaded top edge of the filter was cut off to enable the holder and contents to fit into the open end of the 30/45 joint on the combustion tube. This combustion tube is used in the analytical train described in a previous paper.' A piece of gum-rubber tubing joins the bottom of the fritted-glass filter to a filter flask, which in turn is connected to a vacuum line, or water aspirator. The rate of flow of amine solution through the bed was

Jan 1, 1951

By C. D. Rugen

Ground raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grinda-bility characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, 'iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other *producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. Character of Ground Raw Mix (Kiln Feed) Grinding in the cement plant in general requires a considerably finer product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size,whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too fine, since her particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely he kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater difficulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1948

By C. D. Rugen

Ground raw material as fed to the cement kiln generally is a mixture of two to four components, each of which may have widely varying physical and grinda-bility characteristics. Chemically similar materials found in the same or different deposits may also differ appreciably in physical properties, depending on their crystalline structure. The calcareous or principal cement raw material may vary from a soft chalky limestone or friable cement rock at one plant to a hard limestone or oyster shell at another plant. Argillaceous materials include clays, shales and granulated slag. Siliceous and/or iron-bearing material, including sand, 'iron ore and cinders, may also be required in addition for certain types of mixes. Frequently differences in grindability characteristics are not given the attention they deserve in comparing grinding results at one plant with those at another or in selecting suitable circuits or equipment. Many types of crushing and grinding units are used, with numerous open and closed circuit arrangements. Both wet and dry processes are used successfully. When rebuilding or installing a new grinding department, the choice of process or circuit in some cases may be dictated by the nature of the materials being ground but in other cases it may be the result of good salesmanship or a compromise. An over-all evaluation of wet process vs. dry process grinding should not be made without considering the effects on all other *producing departments in the plant. In general, the more recent grinding installations, both wet and dry, have employed closed circuits, but many older open circuits are still in successful operation. In our experience, closed-circuit raw grinding pays, because of lower power consumption and less operating labor per ton of product. However, some dry open-circuit mills with improved equipment and operating methods compare favorably in performance with dry closed-circuit units. Character of Ground Raw Mix (Kiln Feed) Grinding in the cement plant in general requires a considerably finer product than in most ore-grinding operations. A distinction between fineness of kiln feed and of cement may be made in that kiln feed preferably should be ground to a limiting size,whereas finished cement should include a range of size fractions including sufficient fine flours to give a product with satisfactory physical qualities. Grinding raw mix for kiln feed therefore is more comparable to ore grinding, although the limiting size is smaller. Most kiln feeds are ground from 85 to 95 per cent passing 200-mesh, depending on mix composition. Some cement chemists believe that raw materials cannot be too fine, since her particles theoretically combine more readily and intimately in the kiln. However, there are certain definite practical objections to extremely he kiln feed, such as loss of kiln dust, unstable material flow through the kiln and greater difficulty in control of chemical composition due to dust loss, and the disproportion of fines from the more easily ground component. Our

Jan 1, 1948

By Oswald J. Heinrich

IN the coal review for the United States for 1875, the Engineering and Mining Journal, January 1st, 1876, remarks about the Richmond coal basin " It has contributed but little to the supply of fuel during the year past, notwithstanding the fact that it is the most favorably situated of all our coal-fields, and possesses a fuel of good quality, well adapted to many important uses. An unaccountable lethargy seems to have fallen on all who have touched this field ; and yet, in the future it can scarcely fail to become one of the great sources of coal supply." In most respects indorsing the above remarks, I take occasion to lay before the Institute the following facts in defence of the Rich¬mond basin; and not willing to criticize other mining enterprises in this field, I will make this one remark in general for all of them. While it is true that very little coal has been raised during the year in this field, it is equally true that even the little that has been raised could hardly be sold. When the output of the largest coal districts in the United States decreases, in consequence of the state of the market, it is not to be wondered at that the former small output of this basin dwindled down to almost nothing. But a far deeper¬seated evil, under which this field is suffering, may be discerned from the following remarks, which I hope will show that the latter part of the above remark in the Journal is not altogether fair. As the history of one mine in this district very nearly represents the history of the whole field, I will endeavor to give an account of the development of the Midlothian Mines, ranging amongst the old¬est in the district, partially taken from a report of Col. Wooldridge, in 1841. Coal was mined in this neighborhood as early as 1700, and used (then so-called extensively) in the vicinity in 1775. A

Jan 1, 1876

By Oswald J. Heinrich

In the coal review for the United States for 1875, the Engineering and Mining Journal, January 1st,, 1876, remarks about the Richmond coal basin: "It has contributed but little to the supply of fuel during the year past, notwithstanding the fact that it is the most favorably situated of all our coal-fields, and possesses a fuel of good quality, well adapted to many important uses. An unaccountable lethargy seems to have fallen on all who have touched this field ; and yet, in the future it can scarcely fail to become one of the great sources of coal supply." In most respects indorsing the above remarks, I take occasion to lay before the Institute the following facts in defence of the Richmond basin; and not willing to criticize other mining enterprises in this field, I will make this one remark in general for all of them. While it is true that very little coal has been raised during the year in this field, it is equally true that even the little that has been raised could hardly be sold. When the output of the largest coal districts in the United States decreases, in consequence of the state of the market, it is not to be wondered at that the former small output of this basin dwindled down to almost nothing. But a far deeperseated evil, under which this field is suffering, may be discerned from the following remarks, which I hope will show that the latter part of the above remark in the Journal is not altogether fair. As the history of one mine in this district very nearly represents the history of the whole field, I will endeavor to give an account of the development of the Midlothian Mines, ranging amongst the oldest in the district, partially taken from a report of Col. Wooldridge, in 1811. Coal was mined in this neighborhood as early as 1700, and used (then so-called extensively) in the vicinity in 1775. A

By John P. Cosgro

The increasing use of internal furnace-boilers for power-plants at mines (doubtless due to the facility with which they may be installed by reason of their portability; the fact that they require no masonry setting, cast-iron fronts, buck-stays, etc., and practically no foundation; and the successful maintenance of their claim to equal and even superior economy, as compared with boilers of other types1) warrants this description of a method of remedying an injury which may occur, to such a furnace, even though it satisfies the requirements of the formula adopted by the U. S. Board of Supervising Inspectors of Steam Vessels.2 I refer to the sagging and deformation which may result from overloading the boilers for a considerable period—say, several days. This is sometimes unavoidable under the exacting conditions of continuous day-and-night service, and (in spite of all rules and precautions) the occasional careless or unskillful work of attendants. Such a trouble is by no means unknown on shipboard, where this type of boiler is so largely employed.

Jan 1, 1906

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus ½ in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in, bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand.

Jan 1, 1950

By M. A. Dayananda, R. E. Grace, P. F. Kirsch

Ternary diffusion experiments were carried out at 750°C with vapor-solid diffusion couples in single-phase copper-rich Cu-Zn-Sn alloys. The Philibert-Guy method was used to calculate intrinsic diffusion coefficients at compositions corresponding to the plane of inert markers imbedded in the diffusion couples. Inter diffusion coefficients were determined at common composition points of intersecting diffusion paths. Intevdiffusion coefficients were also obtained at compositions corresponding to maxima in the tin concentration pvofiles Relations between the interdiffusion coefficients and the expansion of vapor-solid diffusion couples are described in detail. Such relations permit the calculation of constant interdiffusion coefficients in binary couples from expansion data directly. In ternary couples expansion data provide an additional constraint on the interdiffusion coefficzents. ThE phenomenological analysis of diffusion in ternary solid solutions has been developed extensively, and various approaches taken in the determination of diffusion coefficients have been reviewed recently by Guy et al.' Finite,' semi-infinite,3 and infinite4 diffusion couples have been used in studies of ternary diffusion, but most of the work has been done with infinite diffusion couples. Semi-infinite diffusion couples3 (vapor-solid couples) have been used to determine both intrinsic and interdiffusion coefficients in the Cu-Zn-Mn system, in which two diffusing species, zinc and manganese, were supplied from the vapor phase. If only one component has a sufficiently high vapor pressure to be supplied from a vapor source, vapor-solid diffusion couples may still be used. In this case the boundary conditions at the gas/solid interface may be governed by partial equilibria rather than by virtually complete equilibrium between the phases. In the present work diffusion measurements were carried out at 750°C with vapor-solid couples of Cu-Zn-Sn alloys. Only zinc was transported between the vapor source and the diffusion disks, because the vapor pressures of both copper and tin are at least 108 lower than that of zinc. Both intrinsic and interdiffusion measurements were made at several compositions. A secondary objective was to relate expansion of the diffusion couples with the interdiffusion process. Such measurements for binary couples yield average values of the interdiffusion coefficients over composition increments. In ternary diffusion couples ex- pansion data provide an additional constraint on the interdiffusion coefficients. COMPOSITION-DEPENDENT INTRINSIC AND INTERDIFFUSION COEFFICIENTS As shown by Philibert and GUy5 the determination of intrinsic diffusion coefficients in a ternary system requires two independent diffusion couples containing marker planes with identical composition. In the case of vapor-solid couples such a requirement torresponds to two couples set up with the same vapor source exposed to two diffusion disks of different composition. Inert markers placed initially on the disk surfaces become imbedded during diffusion. If the pair of couples exhibits appreciable marker burial with marker planes of virtually the same composition, the intrinsic diffusion coefficient may be evaluated at the composition of the marker planes. Fig. 1 is a schematic diagram of the concentration of of a Cu-Zn-Sn ternary vapor-solid couple after diffusion of zinc from a vapor source into a binary Cu-Sn alloy. The areas, Ai correspond to the cumulative intrinsic fluxes of the three diffusing species across the marker plane:5 where Ji is the intrinsic flux of component i, t is the diffusion time, and D3i are the intrinsic diffusion coefficients. For the determination of interdiffusion coefficients a pair of diffusion couples with intersecting diffusion paths is needed. At the composition point of intersection (C1, C2) the coefficients are evaluated from the equation:3

Jan 1, 1969

By Ronald A. Murdock

INTRODUCTION Exxon's Highland Uranium Operations in eastern Wyoming consists of an open pit, an underground mine and a mill complex. The geology of the deposit is reviewed in this paper, and an overview of the mining operations at both the surface and underground mines is presented. Topics discussed include geology, stripping of overburden and mining of ore in the open pit, and underground development and stoping methods. GEOLOGY The Highland uranium deposit was discovered in 1968 by Exxon Minerals Company, U.S.A., in Converse County, Wyoming, 35 miles north of Douglas. The mine is located at an elevation of about 5,200 ft in a high-plains, sagebrush-covered prairie typical of eastern Wyoming. The deposit is near the southern edge of the Powder River Basin in the Paleocene Fort Union Formation. The Fort Union Formation consists of 1,900 to 3,200 ft of sandstone, siltstone, mudstone, claystone and coal beds. Siltstone, mudstone and claystone are collectively referred to as "shale" at Highland. There are many alternating layers of shale and sandstone in the Fort Union Formation; but in the Highland area, there are only three principal sandstones, known as the Highland Sand Group, which host the uranium. The combined sand thickness is about 150 ft.

Jan 1, 1983

By Eugene Coste

In a recent paper' I took exception to the opening paragraph of Mr. Hill's paper, in which he says:— " In endeavoring to interpret the geological occurrence of oil, the geologist is confronted by the fact that science has not yet solved the problem of its origin, which lies at the root of the subject.... For the present we must consider oil as a material in the rocks, the origin of which is still unexplained." I take this occasion to repeat my objection to the above statement, as well as to the similar statement of Mr. C. W. Hayes and William Kennedy in their recent bulletin2 on the same oilfields :—" The origin of petroleum is one of the most obscure problems by which geologists are confronted." I do not hesitate to say that these statements, which claim we know so little to-day of the origin of petroleum, are not warranted in the present state of geological science, and that, on the contrary, geology can to-day most clearly prove the origin of oil to be inorganic and the result of solfataric volcanic emanations. It has been so long assumed that oil or bitumen is due to the decomposition of the organic remains of the sedimentary rocks, that the words organic and bituminous are used synonymously and, accordingly, without attempt at explanation, the origin of oil is in every case ascribed to some bituminous-shale horizon, more or less full of organic matter. Such falla

Jan 1, 1905

By Edwin M. Chance

During the last decade many conditions have been encountered that have materially increased the cost of the production of coal. As in most cases it has not been practicable to increase the selling price of such coal sufficiently to insure the necessary margin of profit, the mine management has been forced to avail itself of what might be termed unusual means that costs might be held at as low a figure as possible. The so-called efficiency engineer has been called upon, costly power plants have been built and machinery has been installed to replace manual labor wherever possible. Another aid used recently to secure economies through the more intelligent production of coal, is the chemist. As the coal industry, barring the production of byproduct coke, does not at once give evidence of its need of the services of the chemist, the writer will endeavor to point out a few of the services that this branch of the staff has been able to render. The preparation of coal in the past has been carried on entirely upon an empirical basis, that is, the criterion adopted has been an ocular inspection. Unfortunately, the appearance of a coal and especially of an anthracite, has but little relation to its fuel value, and as long as coal is purchased for the heat that can be obtained from it by its combustion, the quantity of such heat that is purchased must be one of the principal desiderata in selecting or preparing a coal. Were coals purchased for use as bric-a-brac or for exhibition in museums it might be both wise and just to purchase them upon their appearance. After 4 or 5 years of investigation the fact has been established that coals of very inferior appearance, and I now have special reference to anthracite, might and often did possess heating and burning properties superior to those possessed by bright coals which in the past had commanded considerable and uniform premiums in the market. This being the case the question arose as to whether the trade could be convinced of this fact. While at first some difficulty was experienced in establishing the quality of such dull coals, still it was found that the real obstacle to the sale of these materials in the past had been the fact that the coal producers' own sales departments felt convinced of the inferiority of this type of fuel and when complaints were registered they were given ready credence. Upon convincing the sales department of the quality of this type of fuel, but

Jan 1, 1917

By A. N. Holden, J. H. Hollomon

Inhomogeneous yielding during the early stages of plastic flow has been observed in many metals and has long been a subject of controversy. Low carbon steel, when strained at room temperature, exhibits a distinct yield point at which the metal ceases to behave elastically and begins to flow plastically without further increase in stress,† often with an actual decrease in stress from that existing at the yield point. One manifestation of this behavior is the familiar Lüders lines. The extent of the yield point elongation (the plastic strain which results without raising the stress above that at the initial yield point) may be several percent. Several explanations of this type of yielding in steels have appeared in the literature:1-3}; 1. The segregation of carbides or other constituents at the grain boundaries of ferrite forms cell-like blocks which break down at a higher stress than that at which the ferrite alone will flow. 2. The precipitation of various constituents within the ferrite itself in some way blocks initial flow until a higher stress is reached, after which a great deal of flow occurs without further increase in stress. 3. The restraining influence of neighboring, less favorably oriented grains in a polycrystal results in a storing up of energy, which on yielding is sufficient to cause the continued propagation of slip bands on the multiplicity of slip systems available in adjacent iron crystals without increase in stress. 4. Local segregation of carbon atoms increases the stress required for the initial propagation of dislocations. The stress required for further deformation is lower.3 Such an explanation would require the presence of upper and lower yield points in single crystals. Low and Gensamer2 have shown that heterogeneous yielding can be eliminated by removal of carbon and nitrogen from polycrystalline steels by wet-hydrogen treatment. They also demonstrated that the re-introduction of minute amounts of carbon or nitrogen caused a return of the yield point. Observations of the initial flow of single crystals containing small amounts of carbon and nitrogen- should provide a clue to the explanation of inhomogeneous yielding. Previous tests of iron crystals4-6 can not be considered conclusive because it is uncertain whether the carbon and nitrogen were satisfactorily removed by the decarburization technique employed. The purpose of the experiments described herein was to determine whether single iron crystals containing either carbon or nitrogen would exhibit in-homogeneous yielding. Experimental Procedures THE PREPARATION OF SINGLE CRYSTALS All crvstals were formed in the following way. Aluminum killed sheet material 80 mils thick was machined into specimens of the outer contour shown in Fig 1. These mildly tapered specimens were decarburized at 730°C for 16 hr in hydrogen that had been bubbled rapidly through water maintained at 70°. The resultant grain size after decarburizing was approximately ASTM 5. Several stress-strain curves were made of the decarburized niate-

Jan 1, 1950

By Alfred Weiss

The business world of tomorrow will experience a major change in its data communication systems, with the mineral industry being among those to feel the greatest impact of this change. This development can be expected to occur over the next two decades at a steadily increasing tempo. One major factor prompting this transformation is the fact that technological knowledge is doubling approximately every five years. Moreover, industry is becoming more and more dependent upon the flow and processing of information in its long-range planning, while government requirements and regulations demand increasingly detailed and precise information on plant operations.

Jan 1, 1971

By Henry M. Howe

THE natural effect of large size should be to increase segrega¬tion. I have previously pointed' to the excessive segregation in many large ingots as tending to confirm this, but I have shown that in case of ingots less than 16 in. square this expected effect of ingot-size is liable to masked by that of other variables. Under these conditions we should expect that if large ingot-size really does tend to increase segregation, this effect would be shown by taking the average of large numbers of cases, so that the effects of these other variables might off-set and cancel each other.

Jan 10, 1909

By Richard P. Rothwell

THE anthracite coals of Pennsylvania are all mined from large veins. A seam less than four feet. in thickness is generally considered as unworkable, those from which most of the coal now comes being from 8 to 30 feet thick. The system of mining employed is, almost without exception, that known as "chamber and pillar work;" that is, the coal is taken out of chambers of from 18 to 30 feet in width, and pillars of from 12 to 20 feet are left between these to support the roof. In general, the entire thickness of the seam, even

Jan 1, 1875

By L. K. ARMSTRING

ANYONE doubting prosperity in the mining industry should visit the Kootenays of British Columbia where the West Kootenay Power & Light Co. is kept busy running new power lines and connecting mines and mills with lines already in service. Quoting from an inspired statement "The four hydro-electric plants of the West Kootenay Power & Light Co. on Kootenay River have been in continuous operation." At the recent 35th annual meeting of the Eastern' British Columbia Boards of Trade held in Nelson, a two-day session indicated unusual activity. The following information was obtained through personal contact, through the press, and by hearsay. Much of it has been checked and proved accurate. Reversing the order of the flowsheet. Secretary J. R. Hunter reported as fol¬lows regarding the value of the 1934 production of the Consolidated Mining & . Smelting Company's metallurgical, plants at Trail and Tadanac:

Jan 1, 1935

By Kefton H. Teague

Olivine is a mineral containing a mixture of forsterite (Mg,SiO,) and fayalite (Fe,SiO,) in solid solution. The name "olivine" was first applied by Werner in 1790 (Hunter, 1941) because of the olive-green color of the mineral. Uses The principal use of olivine is in various foundry applications. Perhaps the largest tonnage is utilized as a special foundry sand for mold-making in brass, aluminum, and magnesium foundries (Schaller, 1957, 1958; Snyder, 1957). Olivine was first used as an industrial mineral in the early 1930s for a refractory material (Anon., 1970; Hunter, 1941). As a refractory raw material, olivine was first introduced in the United States as handcobbed, selected, shaped blocks of crude olivine. This use met with limited success. More recently, finely ground olivine blended with MgO and pressed into bricks, which are then fired, have found use in glass tank furnaces and open-hearth furnaces. Ramming or gunning mixes for basic furnace linings also utilize olivine. Olivine has been used in ladle linings with varied success. In Europe, substantial tonnages of olivine are utilized in refractory brick for night storage heaters (Anon., 1970). A limited amount of olivine has been used in the past as a fertilizer (magnesium source) and has been fused with rock phosphate to produce a magnesium phosphate as a plant food. The relatively high magnesia (MgO) content of olivine also attracted attention to it as a potential source of both magnesium compounds and as a source of metallic magnesium (Bengston, 1956; Hunter, 1941). Industries using olivine have not standardized specifications. Normally, producers supply a product which meets individual customer requirements. Such requirements involve type and amount of impurities, grain size of product, refractory characteristics, etc. Geology Olivine occurs commonly as accessories in basic igneous and basic metamorphic rocks. Economic deposits are of magmatic origin and are restricted to essentially the dunite variety of periodotite. Dunites are medium to coarse- grained crystalline rocks, generally reddish brown on weathered outcrop, and are composed primarily of olivine.

Jan 1, 1975

By P. Barnes

The object of this paper is to make a brief comparison of the outlines of several forms of ports for steel-melting turnaces, in reference chiefly to the proper mixture; of the gas and air, and to the direction in which the flame is thrown down into the interior of the furnace. In the illustrations on the accompanying plate, Fig. 1 shows a form of port designed by M, Pernot, of St Chamond, France. This is used with the dome roof preferred by him fur the revolving bottom that bears his name. From No. 1 has been derived No. 2. This is shown on the plans of Mr. A. L. Holley, and from them three large furnaces have been built and put into operation by the Springfield Iron Company. Fig. 3 shows an outline proposed by Messrs. Richmond & Potts for the Pernot furnace. In this the ports are brought in under an arched roof of nearly the ordinary form, instead of over the top of the roof, as with the dome of M Pernot, Fig. 4 shows a furnace as built by Krupp of Essen, Prussia, for fluid refining, or " washing "-—to use the briefer French term. in this the gas and air come into contact in broad sheets one above the other, Fig. 5 shows the form used by Messrs. Richmond & Potts

Jan 1, 1881

By P. Barnes

THE object of this paper is to make a brief comparison of the out-lines of several forms of ports for steel-melting furnaces, in reference chiefly to the proper mixture of the gas and air, and to the direction in which the flame is thrown down into. the interior of the furnace. In the illustrations on the accompanying plate, Fig. 1 shows a form of port designed by M. Pernot, of St Chamond, France. This is used with the dome roof preferred by him for the revolving bottom that bears his name. From No. I has been derived No. 2. This is shown on the plans of Mr., A. L. Holley, and from them three large furnaces have been built and put into operation by the Springfield Iron Company. Fig. 3 shows an outline proposed by Messrs. Richmond & Potts for the Pernot furnace. In this the ports are brought in under an arched. roof of nearly the ordinary form., instead of over the top of the roof, as with the done of M Pernot, Fig. 4 shows a furnace as built by Krupp of Essen, Prussia, for fluid refining, or “washing” -to use the briefer French term. In this the gas and air come into contact in broad sheets one above the. other. Fig. 5 shows the form used by Messrs, Richmond & Potts

Jan 1, 1881