Search Documents

In situ mining is no longer a "last ditch" approach for recovery of uranium, but a proven and competitive method of exploiting sedimentary deposits. Today, in any feasibility study of uranium properties, the project manager would be prudent to compare the economics of in situ methods with conventional surface and underground techniques. In this comparison of in situ and open-pit mining, John J. Borkert and Carl E. Gerity of Occidental Minerals Corp., evaluated a group of hypothetical uranium deposits using the three most sensitive depositional characteristics of depth, size, and grade. Their conclusion: in situ is generally the better method to maximize total net profits and return on investment. At uranium values of $40 per pound, their analysis found open-pit mining to he unprofitable, generally, when stripping ratios were greater than 30:1, the deposit grade-thickness (GT) was 0.5 or less, or the ratio of depth to GT was greater than 200.

Jan 10, 1978

By Howard N. Eavenson

In many of the bituminous-coal districts of this country, more than one seam of workable coal exists, and in most cases the lower seam is the more attractive, owing to either its greater thickness or its superior quality. Apprehension that the mining of a seam will destroy the availability of all overlying seams has hindered the development of many fields and has led to the unprofitable working of certain seams in order to save them from an expected total loss. The U. S. Coal & Coke Co., Gary, W. Va., was the first operator in the Pocahontas field to mine the No. 4 seam extensively, which occurs about 80 ft. above No. 3, the scam that was worked first. This was due to the fact that over large areas the upper seam was the only one of workable thickness, at that time. In two places, both seams were workable in the same area, the No. 4 being thinner and containing more impurities than No. 3 seam. In mining these areas, an attempt was made to keep the workings in the upper seam in advance of those in the lower one, and no pillar robbing was done in No. 3 seam until after pillars in that part of the upper seam directly over it had been mined. This resulted in an excessive development in the lower seam, with large areas of finished rooms and standing pillars. The top fell badly, and after a couple of years the falls became so heavy that pillar drawing was unduly expensive. To overcome this obstacle and allow No. 3 seam to be worked in some territory where No. 4 was thick, but too dirty for present use, a study was made of operating methods applied to superimposed seams in Pennsylvania and Maryland. This was started more than seven yean ago by the writer; his data, supplemented by more recent information gathered by his associates, and by two cases mentioned in recent foreign publications, form the basis of this paper. Central Pennsylvania In central Pennsylvania, the lower coal measures contain several seams of nearly the same thickness but of varying quality, and as mining

Jan 1, 1923

By Howard N. Eavenson

In many of the bituminous-coal districts of this country, more than one seam of workable coal exists, and in most cases the lower seam is the more attractive, owing to either its greater thickness or its superior quality. Apprehension that the mining of a seam will destroy the availability of all overlying seams has hindered the development of many fields and has led to the unprofitable working of certain seams in order to save them from an expected total loss. The U. S. Coal & Coke Co., Gary, W. Va., was the first operator in the Pocahontas field to mine the No. 4 seam extensively, which occurs about 80 ft. above No. 3, the scam that was worked first. This was due to the fact that over large areas the upper seam was the only one of workable thickness, at that time. In two places, both seams were workable in the same area, the No. 4 being thinner and containing more impurities than No. 3 seam. In mining these areas, an attempt was made to keep the workings in the upper seam in advance of those in the lower one, and no pillar robbing was done in No. 3 seam until after pillars in that part of the upper seam directly over it had been mined. This resulted in an excessive development in the lower seam, with large areas of finished rooms and standing pillars. The top fell badly, and after a couple of years the falls became so heavy that pillar drawing was unduly expensive. To overcome this obstacle and allow No. 3 seam to be worked in some territory where No. 4 was thick, but too dirty for present use, a study was made of operating methods applied to superimposed seams in Pennsylvania and Maryland. This was started more than seven yean ago by the writer; his data, supplemented by more recent information gathered by his associates, and by two cases mentioned in recent foreign publications, form the basis of this paper. Central Pennsylvania In central Pennsylvania, the lower coal measures contain several seams of nearly the same thickness but of varying quality, and as mining

Jan 1, 1923

By H. C. Miller

The energy stored in the compressed natural gas absorbed in or otherwise associated with the oil in reservoir sands is usually the most important factor in oil recovery. It is recognized that hydrostatic pressure and gravity may aid materially in the drainage of oil, but in the early life of the majority of fields the principal source of propulsive energy is the expansive force of the gas associated with the oil. Since gas is admittedly the most important factor in the production of oil, its control so as to produce the maximum amount of oil with the minimum amount of gas will be reflected in increased oil recovery from reservoir sands. Controlling the gas means regulating its expansion so that the velocity of flow of oil through the channels in the reservoir sands is neither so great that frictional resistance becomes excessive nor so slow that the gas, because it can travel more rapidly than oil through the irregular passageways in the sands, will by-pass and reach the well without. doing useful work in bringing oil from the sands. Oil and gas flow from the reservoir sands to the well because of differences in pressure. The rate of flow is dependent upon the differential pressures existing in the sands and in the well. By altering the amount of back-pressure maintained on the well this differential pressure can be regulated and changed from a maximum (well flowing "wide open") to a minimum when there will be no flow. Oil and gas flow through the irregular channels in reservoir sands at different rates mainly because of the fact that one is a liquid and the other a gas. Therefore, because oil and gas have different characteristics of flow, application of back-pressure, changes the rates of flow with relation to one another so that wide variations in gas-oil ratios are possible. Obviously, the formation gas energy will be utilized most efficiently when a unit of gas delivers the maximum amount of oil to the well. Determination of Necessary Back-pressure The amount of back-pressure that should be maintained against the producing sand in order that the minimum amount of gas will be produced with each barrel of oil can be determined only by actual field tests made

Jan 1, 1929

By J. R. Wylie, L. C. Huntley

Drilling for oil in the eastern producing states was fairly active during the first part of 1931, although less so than in 1930. With low prices development declined during the year, until the low prices of the summer resulted in an almost complete shut-down of drilling. This coincided with the action of the Conservation Board of the Pennsylvania Crude Oil Producers Assn, in limiting pipe line runs to 50 per cent of the 1930 normal for the Bradford district and upper country, and to 70 per cent for the balance of the region. Not only was new drilling halted but in many cases oil-producing properties were shut in. In November crude prices were partly restored, and all oil offered was being taken except in the Bradford district which was restricted to 80 per cent of the 1930 normal. During the latter part of the year drilling was being resumed on a moderate scale, and new production indicated a resumption of the proration order. The interest in gas development which has been under way for several years, maintained its supremacy over the search for oil in 1931. New reserves of importance were developed during the year in the Western Kentucky Coal Basin, in the Eastern Kentucky shale gas territory, in Stark County, Ohio, as well as the Oriskany sand development in northern Pennsylvania and central New York. A gas line was completed to the Eastern Seaboard serving Washington and Baltimore, and other lines were under construction designed to serve portions of the territory not hitherto supplied with natural gas. The low price of fuel oil at seaboard is understood to be the deterrent factor against further extension of natural gas lines to these markets at present. The development of these new reserves, as well as those developed by intensive drilling in old areas, resulted in the building up of large potential gas production and a lowering of rates paid to the producer. This, coupled with the country-wide tendency to lower the consumer rates of all public utilities, resulted in a general threat to reopen rate cases before various state commissions. Oil Development The past year was marked only by the almost complete shut-down of new development, reaching its low point during the summer, with its

Jan 1, 1932

By H. E. Mills

THE local auditorium of a little Alabama mining town was crowded with expectant men, women and children, as the bulletin board had announced the addition of visiting entertainers to supplement the local talent and motion pictures which usually made up the program of the regular monthly safety meeting. In the audience, near the stage, sat a group of bright-faced boys in boy scout uniforms, discussing the picture just completed. As the lights flashed on a crash and scream was heard from the outside, a shrill whistle and word of command from the scoutmaster, and five of the scouts ran out of the hall, while the mine super-intendent stepped on the stage and requested everyone to keep their seats. The scouts returned, three of them carrying a limp figure in their arms, while the other two cleared the doorway and aisle of excited spectators. They marched to the stage and, placing the apparently badly-injured boy on the floor, proceeded to give an expert demonstration of first aid to the injured. The scoutmaster then explained to the audience that the whole affair had been arranged for their benefit, and invited the local first-aid men to come up on the stage to examine and criticize the boys' work. This gave an opening for several talks on the value of first-aid training and accident prevention, which is the main object of the monthly meetings. This demonstration was given by the first-aid team of Troop One, and the entertainment was provided by members of Troop One and Twenty-eight of the Bir-mingham Scout Council, organized by the writer for the purpose of promoting interest in the welfare and safety meetings in the mining villages of the State. During the past year they have visited a number of such meet-ings and presented programs similar to the one men-tioned above. However, in order to assure a good attendance, entertainment features must also be pro-vided, and the serious part of the evening program was interspersed with excellent vocal and instrumental mu-sic, dancing and novelty acrobatic acts furnished by the visiting scouts. In addition to the numerous first-aid teams of the Birmingham Council, there are hundreds of scouts scat-tered throughout the mining district whose knowledge of first aid, safety first, life-saving, personal health and public health are a constant source of protection to their community. All of these subjects are covered by merit badge pamphlets and are required of an eagle scout.

Jan 2, 1927

By David Turnbull

IN most reactions involving solids the transformation kinetics may be represented by the combination of two processes-those of nucleation and of growth. For example, Mehl and his coworkers 1,2 in their studies on the transformation of austenite to pearlite in steels have been able to describe the kinetics in terms of the rates of nucleation and of growth. By micrographic examination of their specimens they determined the nucleation rate (rate of appearance of pearlite colonies) as a function of time, of percent transformation, and of temperature. They observed that after an incubation period in which no nuclei are observed, the number of nuclei appearing per unit time per unit of untransformed grain boundary area, increases at an increasng rate with time. When recrystallization rates have been interpreted in terms of rates of nucleation and growth and the rate of nucleation determined, an incubation period followed by an increasing rate of nucleation has also been reported. Among the studies in which this phenomenon has been observed are those of Kornfeld and coworkers3 on cold-drawn aluminum wire, of Anderson and Mehl4 on the recrystallization of aluminum sheet, and of Stanley and Mehl5 on the recrystallization of silicon ferrite sheet. The existence of an incubation period during which no nuclei are observed does not appear to have been reconciled with the generally accepted Volmer-Becker theory of nucleation in condensed systems. This theory ostensibly requires the rate of appearance of nuclei to be independent of time. VOLMER-BECKER THEORY In order to form a stable nucleus of a new phase B in a mother phase A, the molecules or atoms of the mother phase must surmount a free energy barrier whose height is determined by the volume free energy change accompanying the transformation and the energy of the surface separating the two phases. The free energy difference between nuclei of various sizes and the molecules or atoms of the mother phase is plotted schematically in Fig I as a function of the radius of the nucleus r. This free energy difference is plotted for two values of the change of free energy per atom, (fB - fA) accompanying the transformation when the volumes of the two phases are infinite. One of these values of (fa-fA) corresponds to a temperature above the temperature To at which the phases A and B are in equilibrium, and the other to a temperature below To. In order for a nucleus of phase B to be stable at a temperature T2 < To, its radius must be equal to or greater than the critical value r* for which the free energy of formation of the nucleus is a maximum, ?f*. Aggregates of phase B having radii equal to or less than r* will be called embryos. Mehl and Jetter,6 in discussing the kinetics of nucleation in solid systems, suppose that embryos of critical size are formed

Jan 1, 1948

By D. W. Mitchell

Mine fires are a serious hazard; surveys show that the coal-mining industry lags considerably behind industry in general in planning and training for fighting fires, and providing adequate fire-protection facilities. The results of the experiments discussed in this paper emphasize that every effort must be made to extinguish a fire in its incipient stage. The research also demonstrated that extinguishing agents and techniques, superior to those presently used in most operating mines, are available. An underground coal mine fire, if not extinguished quickly, can develop rapidly, create a serious hazard, and cause loss of life and property. The problem of controlling a fire increases in direct relationship to the time interval necessary to initiate control measures; as the fire increases in size and intensity it becomes progressively more difficult to cope with roof control, visibility, ventilation, and explosion prevention. Despite the constant vigilance of the industry, the number of coal mine fires is increasing. During the eight-year period, July 1952 to July 1960, following enactment of the Federal Coal Mine Safety Act, the Bureau of Mines investigated 401 fires that caused 30 fatalities and 75 injuries. More than half of these fires burned for more than one shift; 20 pct could not be extinguished by direct attack and had to be sealed. Agents and techniques for extinguishing simulated mining-machine and underground coal fires have been investigated in the Bureau&apos;s experimental coal mine. The research shows that visibility in the fire area is a primary factor affecting control operations. Associated with good visibility is accessibility to the fire; the closer the attack can be made, the less time and quantity of agent are required for extinguishment. Approach to the fire and visibility are hindered by the smoke and hot gases backing up against the ventilating current. In open entries an increase in air velocity assists in driving smoke ahead; at low airspeeds approach can be made by placing a brattice across the lower two-thirds of the entry, pushing the smoke ahead with water sprays, or discharging rock-dust from a rock-dust distributor. In a dead-end entry, fires can be approached by coursing fresh air along an airtight line brattice. However, it is safer, easier,

Jan 1, 1962

By Stanley J. LeFond, Neal Davis

Drilling an oil well or most other types of drilling or coring is no longer a simple and uncomplicated operation. Drilling today at depths which exceed 30,000 ft is hazardous and requires personnel with long and varied experience in drilling. It also requires extensive experience and knowledge in the use of materials which are added to the drilling fluid or "mud," more often than not materials utilizing an industrial mineral. The drilling fluid can vary from a simple mixture of water and "mud" to a very sophisticated, scientifically compounded drilling fluid. Industrial Minerals Used in Drilling Fluids Industrial minerals which are commonly used in oilwell drilling and completion are listed on [Table 1]. The most important minerals, determined by sales, are bentonite and barite. The other minerals listed are either used to achieve a specific purpose or are used regularly but in limited quantities. The main suppliers of drilling fluids internationally are Magcobar Div., Dresser Industries, Inc.; Baroid Div., National Lead Co.; IMC Drilling Mud Co., (a subsidiary of International Minerals and Chemicals Corp. and Halliburton Co.) ; and Milchem, a division of Baker Industries. Most of the industrial minerals are found in North America, with barite mines and processing plants located in Nevada, Arkansas, Missouri, and Arizona, and bentonite mines near Graybull, Wyo. Other mines, such as those in Nova Scotia, are capable of shipping to South America and to the European and Middle East countries. Most of the materials processed by any of the suppliers must conform to specifications set by the American Petroleum Institute (API) or the Oil Companies Material Organization (OCMA). These specifications provide for uniform physical and chemical properties of the materials to be sold on the open market.

Jan 1, 1975

By J. Sibakin, R. D. Hindson

In order to devise a practicable soaking pit schedule for use at The Steel Co. of Canada Ltd.&apos;s Hamilton Works, soaking pit heating temperatures, sooking times, pit capacity, and safe maximum mill drafts were correlated with fluctuations in the current or load of the bloom mill driving motor. Other variables such as total delays in the pit, rolling schedules, mill delays, and track times were also investigated. IN order to show an easily applied and accurate means of establishing soaking pit heating temperatures, soaking times, pit capacity, and safe maximum mill drafts, these various factors are correlated herein with fluctuations in the current or load of the bloom mill driving motor. Rolling practices have a considerable influence on the production capacity of a blooming mill. The maximum values of the torque, in particular, are of importance, since even instantaneous current peaks lead to the tripping of the motor by the overload relay and result in loss of mill time. The establishment of safe maximum drafts and accelerations for ingots of different sizes and of a soaking pit practice which would ensure a consistent and satisfactory plasticity of the metal is of considerable importance for increasing the efficiency of both the blooming mill and the soaking pits. The Bloom Mill Dept. of the Hamilton Works, The Steel Co. of Canada Ltd., is equipped with one 44 in. mill driven by a 7000 hp motor with the setting of the overload relay at 22.0 ka. The speed of rotation of the motor is regulated after the Ward-Leonard system. There are three basic speeds of 9.5, 28, and 47 rpm and a further possibility of increasing the speed by weakening the field. This last possibility is hardly ever used during practical operations. The rolling program of the blooming mill is varied, both in the size of the ingots to be handled and in the steel grades. The total tonnage handled by the mill is about 2,000,000 ingot tons per year. At the time of the investigation, the Bloom Mill Dept. was equipped with 22 soaking pits (6 regenerative, 14 bottom-fired, and 2 one-way top-fired pits) with a total bottom area of 2770 sq ft. The pits are fired with a blast furnace-coke oven gas mixture having a calorific value of 155 Btu per cu ft. The foregoing figures show that the production program was such as to impose the necessity of a most efficient usage of the available equipment. For this purpose, the operations of the 44 in. mill and of the soaking pits were investigated, and the results of the investigation were used as a basis for a revised soaking pit schedule and drafting practice. The plasticity of an ingot of a certain chemical composition when being rolled is determined mainly by the following factors: I—the ingot size, both thickness and width; 2—the length of the gas soak; and 3—the surface temperature. The first two factors determine the uniformity of the temperature distribution over the cross-section of an ingot. The third factor introduces the level of the heating of an ingot. The torque produced by an ingot being rolled is determined by the area of the metal displaced, its plasticity, and acceleration values. On the other hand, with shunt motors the torque is determined by the current. This can be assumed to be correct with only a small degree of error for compound motors with a relatively small effect of the series windings as long as the velocity is not regulated by weakening the field. Since the spread is relatively unimportant when compared to the width of an ingot and since it is also reduced several times during rolling by edging passes, the draft alone and not the area of the metal displaced may be taken into consideration with ingots of a similar size. It is therefore possible to determine the main features of the heating and drafting of an ingot by measuring the current and acceleration of the mill motor. After the acceleration has been taken into account, the amount of current will be an indication of how the motor responds to a heating and/or drafting practice and these practices can be adjusted in order to get the desired result. As peak currents are more likely when heavier ingots are rolled, the rolling of plate and slab ingots was investigated. Conditions prevailing when smaller ingots are rolled can be deduced from the results obtained on heavier ingots. All measurements were made when plain carbon grades under 0.15 pct C were rolled. The motor current, the voltage across the armature, and the rpm were recorded simultaneously on synchronized charts, Fig. 1, which moved with the speed of 6 in. per min. Each draft was recorded by a special observer. The rpm curve made it possible to establish the acceleration at any given moment. For purposes of correlation, the maximum current during a pass and the corresponding acceleration were used. The charts made it possible to establish the position of the roller&apos;s lever at any given moment as well as the total time of a pass. The slab ingots were divided into three groups (28x35, 28x45, and 27Mx53 in. ingots) and each group was investigated separately. Since they account for most of the current peaks, only flat passes were used for purposes of correlation, a total of 1373 having been investigated.

Jan 1, 1956

By Alden B. Greninger, Alexander R. Troiano

THE crystallographic mechanism for the austenite-to-martensite transformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite-and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite undergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.-Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about -70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of I mm. or more. Four martensite cystals from four different ingots were prepared in this manner; the largest crystal of this group is illustrated in Fig. I. Back-reflection Lane patterns were obtained from martensite [ ] crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution (±0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to {112} and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By A. J. Sedriks

ALTHOUGH the occurrence of a readily visible tarnish on the stress-corrosion fracture surfaces of titanium alloys tested in oxygenated nitrogen tetrox-ide solutions has been reported,&apos; the possibility that the formation of this tarnish is a requirement for cracking to proceed does not appear to have been considered. It has been proposed that failure occurs in this system as a result of some electrochemical-mechanical process.2 However, recent studies3-6 of the stress-corrosion cracking of a brass in certain ammoniacal solutions, which also cause visible tarnishing, have led to the view that failure occurs by the repeated formation and fracture of a brittle surface film of cuprous oxide. The purpose of this note is to point out the similarities which exist between the tarnish which forms on a brass and that found on titanium alloys failed in nitrogen tetroxide, and to suggest, by analogy, that a similar tarnish-rupture mechanism may be operative in the latter case. The titanium alloy selected for the present study contained 5.2 pct Al, 2.5 pct Sn, 0.025 pct C, 0.16 pct Fe, 0.014 pct N, 0.012 pct H, 0.07 pct 0, and 0.002 pct Mn by weight. Vacuum-annealed alloy strips measuring 4 by 0.25 by 0.04 in. were used to prepare self-stressed test specimens. Each specimen was made from two strips by bending the end portions and spot welding them together to produce curved sections of uniform bending stress. (The exact details of preparing such specimens have been described by Lisagor el al.7) The curvature in the strips determines the ma-magnitude of the outer fiber stress, which in the present specimens was 100,000 psi (yield stress = 120,000 psi). The specimen surface in the spot-welded end regions was shot-peened to induce compressive stresses and thereby eliminate the possibility of stress-corrosion cracking in these regions. The test environment was nitrogen tetroxide, initially containing 99.5 pct N2O4, 0.1 pct H2O, and 0.08 pct C1, through which oxygen had been bubbled for 30 min. During testing the tetroxide was subject to an oxygen pressure of 250 psi. The duration of the test was 96 hr, and during this time stress-corrosion cracks propagated through some 50 pct of the thickness of the specimens. After testing, the tarnish was liberated from the fracture surface by immersion in a methanol-5 pct bromine solution, and then examined by electron dif- fraction and transmission electron microscopy using a JEM-7 electron microscope. The possibility that the bromine solution had affected the structure of the tarnish was investigated by an "in silu" examination of the stress-corrosion fracture surface using a reflection electron diffraction attachment designed for handling bulk specimens. Typical areas of the tarnish liberated by the me-thanol-bromine solution are shown in Fig. 1. Fig. l(a) reveals that the tarnish consists of individual platelets, and from Fig. l(b) it can be seen that the platelets are joined together to form a semicontinuous film, the boundaries of the titanium substrate grains being retained in the tarnish. Electron-diffraction patterns taken from these areas exhibited diffraction spots typical of a monocrystal. The diffraction pattern shown in Fig. 2 was taken from the central area in Fig. l(n). Monocrystal patterns obtained from areas containing numerous individual platelets can only be explained by assuming that their growth is governed by the titanium substrate (i.e., their growth is epitaxial). In other areas, the tarnish had folded over or became mechanically damaged, and these areas gave diffraction patterns consisting of "spotted" rings, enabling interplanar spacings of the tarnish lattice to be determined. These spacings, measured using a

Jan 1, 1968

By S. W. Parr, F. B. Hobart

Studies relating to the behavior of coal toward oxygen may have for their purpose the determination of the fundamental factors that underlie spontaneous combustion, weathering and deterioration, and the general topic of storage, as well as those properties that have to do with the underlying principles of carbonization. There is also involved the possibility of developing information relating to the constitution of coal, or at least the chemical properties inherent in the type substances of which the coal is composed. It is the purpose here to record certain results bearing on this latter idea of the chemical properties that characterize the main constituents of bituminous coal. The avidity of freshly mined coal for oxygen has long been known. What happens to the coal or to the oxygen is not so clear. Is the oxygen absorbed or chemically combined, and what are the conditions as to time, temperature, texture, or components that are most involved in the phenomenon? If we subject a weighed quantity of coal maintained at a constant temperature to a current of oxygen, we may obtain three factors of interest—the weight increase of the coal, the weight of the water, and the weight of the carbon dioxide formed in the reactions involved at that

Jan 1, 1925

By M. W. Strong

THE technique of handling drilling muds varies somewhat, partly because of personal factors but mainly because of differences in forma-tion, the type of problems met with, and the general drilling conditions in different localities. The much greater depths to which bore holes are now carried have made necessary closer attention to and great modifications of all aspects of drilling-mud technique. Increased depth means smaller hole, smaller drill pipe, smaller clearances, higher pumping pressures, higher differen-tial pressures between shows and the mud column, less accurate control of the weight of the mud column, delayed receipt of formation data, and poorer samples. It means longer delays and greater hazards in rectifying mistakes or dealing with accidental occurrences. Equipment on a larger scale is necessary and more pains must be taken with layout. Lastly, the budget costs of raw materials have risen to high figures and economy of time and of direct monetary expenditure have come to mean much more than formerly. A mud laboratory is now part of the essential establishment of a modern oil field and to it current problems can be submitted for the most thorough investigation. The detailed chemical properties of all mate-rials purchased or quarried have to be investigated. Detailed data on the physical properties have to be ascertained and research on improve-ment of material and its most efficient use has to be carried out. In this paper we propose to discuss the main mud problems with which we have to deal in Iran, some of which are peculiar to our local conditions while others are of the general type common to all workers in this subject.

Jan 1, 1938

By Robert Kinzie

WHEN Mr. Cameron, the President of the Santa Cruz Portland Cement Co., returned from Europe in 1929, he brought first-hand infor-mation about a very versatile type of hydraulic cement. It was not a new cement, many articles having been written about it in foreign journals, but in this country the record of this type of cement had been either neglected or minimized. Using local materials, and applying the information brought back by Mr. Cameron together with many data in numerous publications, the Santa Cruz Portland Cement Co. developed the Santa Cruz high-silica cement. This cement is manufactured by grinding with portland cement clinker a properly calcined mixture of siliceous material and lime. It has all the utility of portland cement, together with an increased resistance to the destructive action of many aggressive solutions. To explain the necessity for the development of a cement having these characteristics, the history of hydraulic binding materials may be reviewed briefly. The materials used as binding media by primitive people were mud, lime, gypsum and bitumin. Due to its utility, ease of preparation, and its common occurrence, lime was the most widely used. Fat lime, when used by itself or with an inert sand, hardened only on the outside surface, where the carbonate was formed by absorption of carbon dioxide from the air, while, the interior of the mortar remained soft. It was quite early discovered that the incorporation of proper siliceous material with the lime increased its ability to harden, and for this purpose various natural siliceous powders were used, such as puzzo-lana in Italy, trass in what is now Germany, and santorin in Greece. These powders reacted with the lime forming a permanent cement and rendered unnecessary the access of carbon dioxide to the mortar.

Jan 1, 1934

By Robert E. Delavault, Harry V. Warren

Circumstances determine whether it is better to make analyses in the field or in a permanent laboratory. The rubeanic acid test described in this article has been designed primarily for field use: it is simple and virtually foolproof, and it requires a minimum of field kit.* It is sensitive, easily detecting 4 ppm of readily extractable copper in a soil. This is by no means a quantitative test, but it is accurate enough to provide a valuable indicator of copper anomalous areas for both prospectors and field geologists. The easiest method for detecting metal deposits that do not produce visible float or stains is to make a simple chemical test for the metal in overlying soil, or in the silt of a stream that may have picked up metal farther upstream.

Jan 11, 1958

R. M. Raymond, New York, N. Y.—The filling and drawing down of the overhead material was done at considerable depth, which is not the usual method in which it starts at the surface.. R. J. Mechin.— It is a little more than 1000 ft. at El Bordo. The vein above had been caved practically to the surface and some of the ore had been excavated, using underhand and overhand square-set methods. This was far enough away from the shaft to prevent any bad effects. When the sill floor was taken out, to insure the old cave material following down well, we put chutes in the square sets for several weeks until we were sure that the material from above was moving down; on each level above, several crosscuts were driven into the old fill by which we could see the material coming down and thus be sure it was following the first. We had to dynamite it very little because it was dry and dusty. The only trouble was that timber starting from the old square sets would get across the chute and hang up. R.. M. Raymond.—HOW many floors did you operate at once? R.. J. Mechin.—We would operate one floor through the whole length and prepare for the second. F. W. SperR, Houghton, Mich.—Could you have worked it in steps? R.. J. Mechin.—Yes; but working it all on one floor was much better for ventilation. The passage between steps would tend to become heavy and blocked and, as the passages from the mining floor down are usually filled with ore, there would be no way for the air to pass up. By means of doors and fans, air was driven to the extreme end of the orebody through the stope and up the other end; but it could have been worked in steps. F. W. SpeRR.—D the following-up material ever become so heavy that you could see weight on the caps before you had to take out the posts?

Jan 1, 1927

By R. F. Weber

The relation between the chemical composition and the refractoriness of fire-brick has long attracted the attention of manufacturers of fire-brick and others interested in their use, yet but little systematic work has been done along this line, especially in the United States. Analyses of fire-brick have been quoted for years, but fire-tests of brick, except those of durability in practical use, have usually been lacking. Although many tests and analyses of foreign fire-brick have been published, only a few have appeared in the United States; and even in the foreign literature, the references and facts are more or less scattered. The most elaborate foreign paper on the subject is that by Dr. Jochum.&apos; One of the earliest, and perhaps the most detailed piece of work in the United States, is that of F. Platt, which was done for the Pennsylvania Geological Survey, in 1876.2 His investigation consisted of the analysis and heat-tests of 21 bricks, the testing being made in an experimental shaft-furnace at Har-risburg, Pa. All the bricks were more or less affected at the temperature reached, which was considerably higher than the melting-point of steel. The exact temperature at which individual bricks fused was not ascertained, hence the comparisons quoted in the paper are of value only for the bricks used in the test. The next comprehensive investigation, made by the New Jersey Geological Survey,³ deals chiefly with fire-clays; analyses and refractory tests having been made of 123 clays, kaolins, feldspars and fire-sands. Here; again, there was no accurate means of measuring the temperature, the only measurement of

Jan 1, 1905

By Everett Carpenter

THE average daily production of crude oil-in Kansas a1 the beginning of the year was about 71,000 1 bbl. and, at its close, 82,000 bbl.-an increase of 11,000 bbl. per day. The total production for the state during the year was about 28,250,000 bbl., or an average of practically 77,500 bbl. per day for the year. This increase in the production was the result of the discovery of several new pools of high-grade oil. COWLEY AND SUMNER COUNTIES One of the principal factors in bringing the production of the. state back to its former level was the newly discovered pools in western Cowley County. During December, 1923, the Waite Phillips Co. completed its Johnson No. 1 in Sec. 20, T. 33 S., R. 3 E., which opened up the Rainbow pool about 12 miles southwest of Winfield. In this pool, the production comes from the Burbank sand, locally called the "Rainbow," found at a depth of 3200 ft. The sand varies in thickness from 25 to 40 ft. in the seventeen wells completed during the year, and the initial productions ranged from 300 to 3000 bbl. per day of 40° Be. oil. The Rainbow pool is purely a wildcat discovery, for no. rocks suitable for the use of the geologist are present. To determine the geologic conditions, the larger companies core-drilled the Rainbow area immediately after the discovery. The Marland Refining, Co., drilling on the Graham farm in Sec. 9, T. 33, R. 3, failed to find the Burbank sand and continued to the Siliceous lime, often erroneously called the Wilcox, at 3505 ft., where a well with an initial production of 900 bbl. of 40 Be. oil was obtained. In the development following this discovery, 4 additional wells were completed, 3 of which encountered pay sand at 2500 ft., the initial productions each being about 200 barrels. Judging by the sands already proved and the area indicated as probably oil bearing by the development to date, these pools have a very promising outlook for the future. It is not unlikely that a field second only to El Dorado may have been opened.

Jan 3, 1925

By AIME AIME

THE value to the engineering profession of a liaison between the engineering societies of Russia and America, through Engineering Council, was the subject of a meeting in the Engineering Societies Building attended by over 500 persons. In introducing the subject, Mr. N. A. Stephanoff, President of the Russian Society of America, said: In Russia, engineers were divided into two classes: those who had graduated from the high technical schools and the practical engineers who had graduated from special technical schools. These technical schools were divided into three groups: The first corresponded to the German polytechnical schools with many departments, mechanical, chemical, metallurgical, mining, etc. The second group corresponded to the French special schools of the "Écoles des Ponts et Chaussées." "École des Mines." The third group was formed by the Military and Naval Academies of Engineers. In 1910, Russia&apos;s high technical schools had about 45,000 students, whose training covered a period of not less than five years, and who enjoyed all opportunities afforded by laboratories in no way inferior to those of Germany.

Jan 1, 1920