Search Documents

R. S. MACPHERRAN,* Milwaukee, Wis. (written discussion?);-Mr. Stork's paper is very interesting, but I am unable to agree with some of his conclusions. He argues very strongly for the beneficial effect of oxygen, but gives no actual determinations of this element to support -his views. He states that the oxygen resulting from a high bed, heavy charges, low coke ratio, etc. must not be confused with the oxygen under normal conditions. I will be glad to know in what respect these oxygens differ or in what state they occur. Is it his opinion that the beneficial type is present as a dissolved gas and the other as metallic oxide? I will not discuss the first five of his six points, as I have not seen enough trustworthy determinations of oxygen in cast iron to form any conclusions as to its effect. I have never known the addition of manga-nese, however, to reduce the strength of cast iron. Under the sixth point, I would say that the addition of steel lowers the total carbon content, and by this action will increase the strength independently of oxygen. This reduction of carbon operates also to raise the melting point. It is interesting to note here that the author, in order to get proper fluidity for his cylinders, was obliged to reduce his oxygen by raising the manganese in the charge.

Jan 12, 1919

By Dever C. Ashmead

Coal companies in the anthracite region are studying various methods of mining, seeking one that will shorten considerably the life of the gangway and thus decrease the maintenance charges. In steep pitching measures, the maintenance charges of the gangways are high because of the cost of replacing timbers and cleaning up falls. Therefore, if the length of the gangways can be decreased and the mining made more concentrated, the life of the coal gangways will be decreased and the maintenance charges per ton of coal produced will be smaller. The practice in the anthracite region is to drive long coal gangways and to work the breasts as the gangway from which they were driven is advanced. In many cases these gangways are from 4000 to 6000 ft. in length; and some are even longer. As these must be maintained not only until they have reached their limit but until second mining begins (which may be some years later), the maintenance charges are high. If the gangway is allowed to close, when the time comes to remove the pillars the cost of re-opening it may be as expensive as the original driving cost. The Lehigh and Wilkes-Barre Coal Co., at its Wanamie Colliery at Wanamie, Pa., has been using a system of mining that, as far as the writer knows, is not used in any other place in the anthracite fields. The

Jan 1, 1925

Professor Somasundaran has given an excellent presentation of the numerous problems which remain to be solved before the selective aggregation of fine particulates is likely to see broad commercial application in the beneficiation of mineral fines. However it is useful, I think, to reiterate some of the major problem areas. The over-riding factor which has limited the development of selective aggregation techniques is that processes such as coagulation and flocculation tend to be inherently non-selective. Conditions which favor the aggregation of one kind of fine particles usually favor the aggregation of all kinds of particles. As Professor Somasundaran has pointed out, the state of aggregation of a fine-particle dispersion is primarily determined by the forces of interaction between the individual particles. In most systems, the dominant forces are: 1. van der Waals - London Dispersion forces between the particles themselves 2. electrical double layer forces 3. steric forces between adsorbed layers on the surfaces of the particles. The London Dispersion forces between like particles are always attractive, but for dissimilar particles dispersed in a fluid medium can, in some cases, lead to a net repulsion. Electrical double layer forces always lead to repulsion between like particles but can, again, cause either attraction or repulsion for dissimilar materials. The steric forces, which are by far the least understood of the three types, can also lead to attraction or repulsion depending on condi-

Jan 1, 1979

By John R. Lotz

A team of American experts is tackling a whole nations's problems, under the banner of a seven-year plan evolved by the Iranians themselves.

Jan 7, 1950

By Christopher C. Barton

Each variable known to affect laboratory measurement of fracture-energy and fracture-toughness is reviewed. Specific examples are cited where each of the variables have been isolated.

Jan 1, 1982

By W. E. Ruder

Considerable interest has been shown lately in various types of furnaces for the production of high temperatures, both for laboratory purposes and for small industrial uses. Dr. J. A. Harkerl described certain modifications of the Arsem graphite resistance helix for high-temperature work at the National Physical Laboratory. Dr. Northrup also has developed two interesting forms of high-temperature furnaces. In 1911, Messrs. Winne and Dantsizen2 described two forms of resistance furnaces using ductile molybdenum or tungsten as resistors. Since the discovery, by this laboratory, of methods for producing these metals in ductile form, their use as resistance elements in the research laboratory of the General Electric Co. has grown to such an extent that they are now almost indispensable. These furnaces are used here for alloy research, annealing, heat-treating, and practically all of the thermal processes requiring temperatures above 900' C. Various types of furnaces have been developed to meet the general needs of laboratory work, and it is the purpose of this paper briefly to describe some of these furnaces. A tubular furnace wound with a metallic resistor is the simplest type to construct, and almost every laboratory has made such furnaces. The only essential difference between a furnace wound with platinum o base metal and one wound with tungsten or molybdenum is that the coils of the latter must be heated in a neutral or reducing atmosphere It has long been our custom here to build our resistance furnaces with : metallic casing from which the tube could be easily removed for rewind ing. The heat-insulating material—usually calcined magnesia, alumina silica, or silex, depending upon the nature of the resistor-—is used i: powdered form so that it can be readily removed and replaced. I order to adapt this method to tungsten or molybdenum windings,

Jan 1, 1918

By H. P. Rassbach, E. R. Saunders

MUCH progress has been made in recent years in the theory and practice of making stainless steel. By effective utilization of oxygen for decar-burization and more suitable alloying agents, it has been possible to attain consistent production of very low-carbon stainless steel. In order to facilitate economical production of stainless steels, the Electro Metallurgical Co. has carried out an extended experimental program that has clarified some of the complex interrelations of temperature and composition under decarburizing and reducing conditions. These results'-:' have been founded in large part on small experimental heats, and in order to confirm their validity and significance under commercial conditions, a survey of stainless steel melting practice has been made with the cooperation of stainless steel producers. Conditions required for decarburization and associated oxidation of chromium, manganese, and iron have been fairly well established in relation to the beneficial effect of the highest practicable temperature. The recovery of chromium and manganese from highly oxidized slags by reduction with silicon has been indicated with somewhat less precision and this study has shown significant deviation in large commercial heats from the small experimental heats. In spite of an unsatisfactory degree of accuracy in estimating the conditions affecting reduction of metallic values, it has been possible to calculate a slag weight in reasonably good agreement with the results observed in large heats. While there still is much to be learned about both the qualitative and quantitative aspects of stainless steel melting, this survey has indicated the manner by which the efficiency of the production process may be measured. Oxidation Period In order to establish practices for the recovery of chromium and manganese from the slag the amounts of these metals oxidized should be known. Moreover, since reduction of oxidized chromium and manganese must necessarily be accompanied by similar reduction of iron, knowledge of the total quantity of metallics oxidized is essential. The relations between carbon, chromium, and temperature under oxidizing conditions were developed by Hilty in 1948.' While it had been realized previously that retention of chromium in the metal during carbon oxidation is favored by high temperatures, the Hilty relation provided quantitative information useful for evaluating melting procedures. For example, it was shown that decarburization to moderate carbon levels can be achieved while retaining substantial amounts of chromium. However, in decarburizing to the low-carbon level necessary for producing 0.03 pct maximum carbon stainless steel, very little chromium remains in the bath at the temperatures generally employed. For this reason, Hilty, Healy, and Crafts' later projected an extension of the chromium-carbon relation to the low-chromium region. Although this chromium-carbon-temperature relation defined the composition of a chromium steel bath at the end of the oxidizing period, it did not provide a direct means for estimating the total amount of metallic oxidation occurring during decarburization of a stainless steel heat. This subject was investigated by Crafts and Rassbach³ and, later, by Hilty, Healy, and Crafts" who demonstrated that metallic oxidation is a function of the chromium content of the initial furnace charge, the minimum carbon content attained, and the temperature. It was further demonstrated from data on 1-ton heats that an empirical relationship exists between the ratio of chromium plus manganese to iron in the slag (S) to the corresponding ratio of these components present in the metal bath. The following expression was derived to permit the calculation of the amount of metallics oxidized during decarburization of a given charge: W-2000 (Cr1 + Mn1)-(Cr2 + Mn2) 1 100s/s+1-(Cr3 + Mn2) where W is the pounds of chromium, manganese, and iron oxidized per ton of charge; Cr1, the percentage of chromium in the charge; Mn1, the percentage of manganese in the charge; Cr2, the percentage of chromium in the bath after oxidation; Mn2, the percentage of manganese in the bath after % Cr + % Mn oxidation; and S =%cr+ % Mn/%Fe in the slag after %Fe oxidation. In order to establish whether the slag ratios of commercial heats are consistent with those found in the experimental heats, the slag and metal analyses shown in Table I were evaluated. These data represent samples taken after the oxidation of two 1-ton and seven 15 to 25-ton heats of types 303, 304, and 304L stainless steel made in chromite, acid, and basic hearths. Fig. 1 illustrates that the results for the commercial heats correlate reasonably well with the relationship originally established for experimental 1-ton heats. It will be noted that in the range of metal composition of these heats, the slag values generally lie above the line. As was suggested by

Jan 1, 1954

By C. P. Davenport, Garth Duell

What are the projected electrical power needs of the nation and of the Northwest during the next 15-20 years? No one who has researched the subject has reached a substantially different result than the following simple conclusion: electrical power requirements are doubling every decade. There are some who question the necessity of a power company's need to install capacity every ten years equal to what it has done during its entire previous history; there are even those who would argue that such growth should be arbitrarily curtailed. However, a power company must, by law, meet its responsibilities of providing the energy the public expects when the switch is thrown.

Jan 10, 1972

By Michael R. Lewis, Dennis P. Moore

Untensioned, fully grouted, steel bars (dowels) up to 30 m long and 45 mm in diameter were used to reinforce rock slopes several hundred metres high, excavated for a hydroelectric project near Revelstoke, British Columbia. These dowels were successfully used to prevent surface rock from loosening, to prevent sliding on interconnected discontinuities and to prevent sliding of relatively intact rock on a thin shear zone. Because the interaction between rock slopes and dowels is not well understood, critical slopes were extensively monitored. Based on the experience from Revelstoke and elsewhere, it appears to be worthwhile, in most circumstances, to reconsider the need for tensioning rock anchors.

Jan 1, 1982

By D. J. Cox, J. P. Conway, A. E. Gooch

A two-year test conducted by the USBM's Spokane Mining Research Center (SMRC) has proven the feasibility of the yielding rockbolt, a concept which may prove very useful to the mining industry by providing ground support under a variety of conditions. The yielding rockbolt was originally developed in South Africa3 to overcome the limitations of conventional bolting in rock subjected to high-stress or rock burst conditions. The yielding effect is obtained by fitting the bolt prior to thread rolling with a smooth-bore die of internal diameter slightly larger than the shank diameter but smaller than the rolled thread diameter.

Jan 4, 1977

By Y. J. Wang

A graphical technique by which the operating points for a two-fan ventilation system can be represented as the intersection of the modified fan curves is described. In constructing the diagram, the air quantities associated with the fans are considered to be independent variables and used as the axes of a rectangular coordinate system. The diagram may include, in addition to the modified fan curves, contour lines for resistances, pressures, and air powers. Procedures for drawing the diagram are discussed and illustrated with an example of the ventilation system.

Jan 1, 1986

By Arthur Crowfoot

As a result of work done, on an operating scale, in its experimental mill during 1920 and 1921, the plan here given was proposed for crushing, grinding, and concentrating low-grade sulfide ores at the Morenci Branch of the Phelps Dodge Corpn. The flow sheet is designed to recover 85 per cent. of the total copper and 95 per cent. of the sulfide copper from ore assaying 2.0 per cent. total copper and 0.3 per cent. acid soluble copper. At present, 1400 tons are treated daily under the conditions of this flow sheet, two 700-ton units having been installed in the 4000-ton concentrator. The run-of-mine ore will be reduced, in the dry-crushing plant, to —6 mesh and then delivered to the concentrator feed bins. The crushing will be done in three stages: (I) Run-of-mine ore is reduced to —2 1/2-in. in a gyratory crusher; (2) the 3-in. ore is reduced to 1/2-in. in 72 by 24 in. rolls; (3) the 1/2-in. ore is reduced to — 6-mesh size in 54 by 24 in. rolls. The 54-in. rolls will operate in closed circuit with electrically vibrated screens, "Hum-mer" type, a conveyor circuit being used to carry the roll product to the screens. Sufficient screens will be installed to pass 1.5 tons undersize per hour per square foot. Fine-ore bin chutes will be piped for compressed air, which will be used intermittently to keep the ore feed in motion if it tends to arch or pipe in the bins. The Concentrator The concentration of the copper and iron sulfides in the ore will be effected in three stages: I. By direct treatment of the —6-mesh crushing-plant product on primary tables, which will recover about 35 per cent. of the original copper content of the ore in a clean granular concentrate. The table middling will be dewatered in Dorr rake classifiers and ground to — 48-mesh in ball mills operating in closed circuit with circulating classifiers.

Jan 1, 1923

By Arthur Crowfoot

As a result of work done, on an operating scale, in its experimental mill during 1920 and 1921, the plan here given was proposed for crushing, grinding, and concentrating low-grade sulfide ores at the Morenci Branch of the Phelps Dodge Corpn. The flow sheet is designed to recover 85 per cent. of the total copper and 95 per cent. of the sulfide copper from ore assaying 2.0 per cent. total copper and 0.3 per cent. acid soluble copper. At present, 1400 tons are treated daily under the conditions of this flow sheet, two 700-ton units having been installed in the 4000-ton concentrator. The run-of-mine ore will be reduced, in the dry-crushing plant, to —6 mesh and then delivered to the concentrator feed bins. The crushing will be done in three stages: (I) Run-of-mine ore is reduced to —2 1/2-in. in a gyratory crusher; (2) the 3-in. ore is reduced to 1/2-in. in 72 by 24 in. rolls; (3) the 1/2-in. ore is reduced to — 6-mesh size in 54 by 24 in. rolls. The 54-in. rolls will operate in closed circuit with electrically vibrated screens, "Hum-mer" type, a conveyor circuit being used to carry the roll product to the screens. Sufficient screens will be installed to pass 1.5 tons undersize per hour per square foot. Fine-ore bin chutes will be piped for compressed air, which will be used intermittently to keep the ore feed in motion if it tends to arch or pipe in the bins. The Concentrator The concentration of the copper and iron sulfides in the ore will be effected in three stages: I. By direct treatment of the —6-mesh crushing-plant product on primary tables, which will recover about 35 per cent. of the original copper content of the ore in a clean granular concentrate. The table middling will be dewatered in Dorr rake classifiers and ground to — 48-mesh in ball mills operating in closed circuit with circulating classifiers.

Jan 1, 1923

By Philip Lindstrom

T he Radon mine is in the north end of the Big Indian mining district in San Juan County, Utah. Hecla Mining Co. operated the mine from early 1955 to early 1964 through an operating agreement with Federal Resources, Inc. Development consisted of a 3-compartment, 690-ft shaft, 4 main levels driven on the ore horizon and a haulage level below the ore. Evaluation of physical and economic factors showed that this flat-dipping ore occurrence could be mined by a low-cost coal mining method. The value of the deposit was high and unusual pre¬miums were possible by clean mining. Complete extraction without loss of ore pillars, minimum ore dilution and high production per man were obtained by longwall mining.

Jan 12, 1964

In Mr. Weed's interesting paper, frequent reference is made to the Cananea copper-deposits, which are said to have been so vigorously exploited that they produced 14,000,000 Ib. of copper in 1901. The ore-bodies which yielded this large quantity of metal are described as a product of contact-metamorphism, and in Mr. Weed's genetic classification of such deposits, they receive a place under the sub-heading, "Deposits impregnating and replacing beds of contact-zone."* They are considered by Mr. Weed to represent a special type under this head, and are further classified as: " l. Chalcopyrite deposits: (a) Pyrrhotite ores; (6) Magnetite ores, Cananea type." In condensing much information into a comparatively small space, the presentation of a subject may be so abbreviated as to detract from its clearness. The situation at La Cananea, considering its importance from an economic as well as scientific standpoint, may he worthy of more detailed description. As Mr. Weed rightly remarks, " structural differences are so important, and have SO marked a bearing, not alone on the theory of their genesis, hut also on the working of the deposits and a determination of their value as mines, that they merit a full discussion."† It is my present purpose: (1) to show that it is doubtful whether the copper of La Cananea is mined, except to a limited

Jan 1, 1903

By E. R. Russell, N. E. Richards

The current ejyiciency of aluminum cells was derived from the metal produced over a period of time and the theoretical faradaic yield. The difference in the actual amount of aluminum in the cathode at the beginning and end of the period must be determined. The weight of aluminum in the cathode was calculated from the dilution of an added quantity of impurity metal. Use of multiple indicator metals, copper, manganese, and titanium, demonstrated that the weight of aluminum in cells can be determined to within 1 pct with routine but careful chemical analyses. Over intervals of the order of 30 days, current efficiencies reliable to within 1 pct can be obtained. INVESTIGATIONS beginning with those of Pearson and waddington ,' through the most recent published work of Georgievskii,9-11 illustrate the direct relationship between the composition of the anode gas and the applicability of analysis of anode gases to the control of alumina reduction cells. McMinn12 noted the lack of an independent method for measuring cell production efficiency over the short term. There is no doubt that changes in the current efficiency are immediately reflected in the composition of anode gases. However, the accuracy of faradaic yields calculated from gas analyses depends upon the degree of interaction between primary anode gas and Carbon.6 A conventional industrial practice of obtaining long-term current efficiency for production units from mass balances and quantity of electricity is generally insensitive to the impact of planned control of any one or more of the influential reduction cell parameters such as temperature, alumina concentration, and mean interelectrode distance. Consequently, there is a real need in the aluminum industry for a procedure to obtain the absolute cell current efficiency over a short term—10 to 30 days—both for the calibration of values obtained from gas analysis6 and for evaluating the effect of controlling specific parameters in the reduction process. The amount of aluminum produced may be determined by considering the cathode pool as a reduction of an impurity metal in aluminum. Analyses over a period will show a decreasing concentration of the impurity due to the accumulation of aluminum solvent. The increase in aluminum inferred from analyses is the amount produced by the cell during the period. Combining weights of the cell aluminum in the cathode at the beginning and end of a specific period, weights of aluminum tapped and the quantity of electricity passed during the interval will yield the current efficiency. Smart,I3 Lange;4 Rempel,15 Beletskii and Mashovets,16 and winkhaus17 have used dilution techniques to determine aluminum inventory in alumina reduction cells. A technique for determining the weight of aluminum in production cells by addition of small amounts of copper to the aluminum cathode was described by smart.13 The precision in values of the aluminum reservoir through dilution of copper in the cathode ranged from about 1 to 3 pct depending upon the quantity of copper added in the range 0.2 to 0.01 wt pct, respectively. Because the method appears so direct and apparently simple, one would not anticipate difficulties in application to industrial cells. The objective of this study was to resolve this problem associated with the trace metal dilution technique for determining the amount of aluminum in a cell. The approach in evaluating trace metal dilution as a basic factor in determining the weight of aluminum in the cell reservoir, and the absolute current efficiency of the Hall-Heroult cell, was to dilute more than one trace metal in the aluminum cathode so that we could discriminate among complications arising from physical mixing, the possibility of separation of intermetallic compounds, loss of the added elements, and chemical detection. EXPERIMENTAL METHODS These experiments are not complex but require standardized procedures. The technique involves addition of the trace metals to the cathode, knowing when these metals are homogeneously distributed in the liquid cathode, timing of the sampling, employing accurate and precise analytical methods, using reliable procedures for monitoring the amount of electricity passed through the cell, and accurate weighing of aluminum removed from the cell during the particular period. More accurate results might be obtained if the increment in concentration of the added indicator metals were of the order of 0.1 to 0.2 wt pct. The method must be applicable to production units and, hence, the contamination of the aluminum minimized. For this reason, the concentration of trace metals in the cathode was kept below 0.07 wt pct and generally at 0.04 wt pct level. Trace quantities of copper, manganese, titanium, and silicon are already present in virgin aluminum and are suitable as additives from electrochemical and analytical points of view. Concentration of silicon is quite dependent upon the characteristics of the raw materials and was not used extensively in this work. Chemical Analyses. All instrumental analyses require calibration against an absolute technique such as a gravimetric, volumetric, or spectrophotometric method which represents the ultimate in sensitivity, precision, and accuracy. On review, the best methods for copper appeared to be optical absorption without

Jan 1, 1969

By Frank Foote

PRECISION lattice-constant measurements have been widely used in the study of cubic solid solutions but as yet have been rarely applied to noncubic solid solutions. (See, however, references I and 2.) With the high precision at present attainable in the measurement of lattice constants, the X-ray method should be readily applicable to noncubic solid solutions. In the work reported here, hexagonal close-packed magnesium was used as the solvent and either lead, bismuth or gold as the solute. In the magnesium-lead and mag-nesium-bismuth systems the a and c lattice constants were determined as a function of composition, densities were calculated from these lattice-constant data, these theoretical densities were compared with those directly measured and the solid solubility limit was determined on quenched specimens over a considerable range of temperature. In the magnesium-gold sys-tem, the solid solubility is very small but we have obtained an indirect check on the solubility limit previously reported.

Jan 1, 1940

By D. A. Rice, R. L. Stone

Studies of the possible effect of plant water chemistry on the strength of unfired iron ore pellets apparently have not been reported in the literature. Naturally occurring soluble salts were removed from magnetic concentrate filter cakes obtained from several iron ore concentrators. Laboratory balling tests showed that unfired pellets made from these "clean" filter cakes were 50-100% stronger than the usual unfired pellets containing the salts. The fact that certain chemical additives dissolved in the water used for balling "clean" concentrates decreased the strength of unfired pellets indicates that salts in the plant process water may be responsible for lower strengths. According to chemical analyses of plant process waters at these plants, calcium and magnesium are probably the most detrimental salts in the plant circuits. It is suggested that calcium, magnesium, and other polyvalent cations in the mill process waters ion-exchange for lower-valence cations in the bentonite and thereby destroy the electrostatic-charge bonding in the green pellet. Some practical guidelines are also included for plant balling practices.

Jan 1, 1973

By Robert L. Grayson, Y. J. Wang, R. Mike Mishra

Prediction of ventilation needs in long range mining projections requires serious consideration when formulating those projections. Predicting the behavior of the ventilation system of an old, complex mine poses an especially provocative problem. Air-flow around and through mined-out areas via bleeder systems, leakage flows through stoppings or other air control devices, and the use of multiple fans all add to the basic complexity of a ventilation system and make predictions of ventilation changes very difficult. Fortunately, the task of making ventilation decisions can be greatly assisted by ventilation surveying and computer simulation. The Nemacolin Mine of Jones and Laughlin Steel Corporation, located in Southwestern Pennsylvania, is one such old mine which used the computerized approach successfully. A mine-wide pressure-quantity survey was used to obtain realistic values for airway resistance factors. These values, together with network topology, formed the basic input for computer simulation. Results from this simulation indicated that air quantities generated at critical airways by the model were generally within a couple of percent of those measured in the actual survey. It was then concluded that the model was acceptable for practical application, and it was used immediately for studying the effects on the ventilation system of changing the blade settings of fans. Additionally, the model was modified to incorporate projected mine development and used to predict future ventilation.

Jan 1, 1982

By Paul E. Queneau, H. J. Roorda

Cobalt consumption will increase during the next decade at an average rate at least equal that of nickel. In the past, use of cobalt has at times been curtailed by lack of availability or by high price. In the future, output of cobalt derived from copper ores and iron sulfides will continue to grow and output of cobalt from nickel ores will be greatly increased. There should therefore be an adequate supply of this metal at a reasonable price. Nickeliferous limonites constitute by far the largest known terrestrial reserves of cobalt. A process has been conceived, based upon selective reduction and aqueous chlorination for treatment of such ores. The proposed procedure permits good extraction of the ore's cobalt content, comparable to that of the nickel, and is adaptable to large-scale, automated unit operations. Chlorine leaching of the ore enhances its value as a potential source of iron and chromium. Over four thousand years ago, cobalt pigments were employed for decorative purposes in some glass and glazes of Egypt and Persia, and by 1000 B.C. they were widely used in the Middle East.' " However, prior to 1914, virtually no cobalt was produced as metal and ceramics remained the largest consumer of the element as oxide. During World War I cobalt-containing high-speed steels came into their own and the metal's merit in magnet steels was established.

Jan 1, 1971