Search Documents

By H. R. Hanley

THE characteristics of alloyed anodes and their influence on the products of electrolysis and power consumption have been noted previously in the literature.1 This paper presents data in continuation of the subject given in an earlier paper by the authors.2 As noted in the authors' previous paper, the objectives of this work are the reduction in the cell voltage and the purity of the cathode product resulting from the use of alloyed lead anodes. The fundamental facts developed in the previous paper were: (1) that the presence of a small amount of calcium lowers the anode potential approximately 50 per cent. below that of pure lead; and (2) that thallium when present to the extent of 4 per cent. rendered the anode practically stable, thereby lowering the contamination of the cathode by lead to a very insignificant amount. The specific features determined in this recent work are as follows: 1. The lowest limit of calcium in the lead which will still give maximum lowering of the anode potential. 2. The characteristics of the thallium-calcium-lead anode. 3. The characteristics of the silver-calcium-lead anode. 4. The characteristics of the thallium-silver-calcium-lead anode. It was determined that 0.1 per cent. calcium in the anode was sufficient to lower the anode potential approximately 50 per cent. Table 1 shows the characteristics of alloyed anodes tested. The anode composed of 0.1 per cent. calcium, 4 per cent. thallium, and 95.9 per cent.

Jan 1, 1931

By G. R. Speich, S. A. Kulin

R. C. Shnay (Dept. of Mines and Technical Surveys, Ottawa, Ont., Canada)-—The authors are to be congratulated on an interesting and informative paper. However, several questions arise when the isothermal formation of martensite .is considered in relation to the formation of bainite at temperatures near the M, point. The reactions in an alloy and in a plain carbon steel would appear to be comparable; and in the course of a recent investigation of the austenite-bainite transformation in a plain carbon steel,Ia the writer has obtained data at temperatures above and below the M, point. These data are in some respects similar to those of the authors and a comparison would seem justified. The steel used in this investigation had the nominal composition: C, 0.80 pct; Mn, 0.20; and Si, 0.20. The course of the transformation was followed by the use of a magnetic balance. The magnetic moment of the specimen as determined by this instrument is directly proportional to the percentage of the total volume of the specimen which has transformed to bainite. ~lf specimens were austenitized at 1850°F for 4 hr, quenched to the transformation temperature, and quickly transferred to the magnetic balance. Readings were taken at regular intervals until the transformation had stopped. A typical transformation curve is shown in Fig. 9. The preliminary curve preceding the S-shaped curve was found at all temperatures above the M, to around 600°F. Both the extent of this preliminary curve and the time interval between it and the S-shaped curve were found to decrease with increasing temperature as was suggested by Davenport and Bain.14 Therefore,

Jan 1, 1953

By S. F. Reiter, W. R. Hibbard

A survey of the effect of heat treatment on the room temperature hardness of Fe-Mo alloys has been made. Constant strain rate tensile tests were performed between room temperature and 1800°F. These data were analyzed to determine the effect of temperature and composition on the strain hardening coefficient and strain rate sensitivity. Constant load creep-rupture tests were made on these alloys and the results related to composition and structure. A relation between the high temperature strength of the precipitation hardened alloys and the volume of precipitate has been observed. IN view of the extensive use of ferritic materials at elevated temperatures, it is surprising to note the limited amount of information relating the variables of plastic deformation, i.e., composition, structure, temperature, stress, strain, and strain rate. Hollomon and Lubahn' showed how the several variables of plastic flow might be treated analytically. No data were available on carbon-free iron and its alloys in a form suitable for this analysis. Several German investigations2-" constitute most of the experimental work relating high temperature properties to the constitution of these types of materials. In order to obtain new data, the iron-rich alloys of the Fe-Mo system were selected for detailed investigation for the following reasons: 1—Some of the important effects of molybdenum on the mechanical properties of iron have already been studied.' , 821 2—By suitable heat treatment of selected alloys, it is possible to study strengthening effects of four types: AT -a transformation, B—substitutional, C—precipitation, and D—dispersion of hard inter-metallic compound. Materials and Treatment Four-pound ingots were vacuum cast, employing the same melting schedule previously used.? The raw materials were electrolytic iron and lamp-grade molybdenum. The ingots were forged to l/z in. sq. rod and one portion swaged to 0.350 in. diam rod for the production of 1 15/16 in. long button-head specimens. The button-head specimen blanks were solution treated for 16 hr at 2100°F in hydrogen of —70°C dewpoint and then water quenched. They were subsequently plunge ground to the standard 0.160 in. diam test bar. Micrographs of the solution treated alloys are given in Figs. la through Id. The higher molybdenum alloys contained large equiaxed ferrite crystals similar to those in Fig. Id. A portion of the % in. rod was hot rolled to 0.100 in., sandblasted, and cold rolled to 0.020 in. Strip tensile specimens having a 0.020x0.200 in. cross-section and a 2.25 in. gage length were machined from the sheet. The alloys containing molybdenum were subsequently annealed 1 hr at 1560°F. The iron strip was annealed 4 hr at 1300°F in wet hydrogen. The resultant structures are shown in Fig. 2a through h. The ASTM grain sizes were 1 to 3 as solution heat treated or 3 to 4 as annealed. The chemical analyses of the alloys are given in Table I. Carbon contents were obtained after the heat treatments in hydrogen. Alloy 15.9 pct Mo was tested as a cast alloy.'

Jan 1, 1956

By Nicholas J. Grant, Raymond E. Cairns

A high-purity chromium, made by solid-state extrusion, and a series of molten, extruded, dilute alloys containing carbon, oxygen, nitrogen, and sulfur were studied to establish the effects of composition, cooling rate, grain size, strain rate, and prior strain on the transition temperature for brittle THE transition from ductile to brittle fracture with decreasing temperature remains of extreme interest especially among the refractory metals, such as tungsten, molybdenum, and chromium, which have relatively high transition temperatures. Fracture, yield stress, and hardness. Tension tests at a strain rate of 0.015 per min were generally utilized. Results are interpreted in terms of the quantity of each element retained in solid solution. Of these elements, chromium has been studied the least, but deserves additional attention because of its superior oxidation resistance for high-temperature use. In the past, impurity elements which have received attention are carbon, nitrogen, oxygen, and sulfur;'-' of these, nitrogen has usually been considered to be the most detrimental. Unfortunately, because of different levels of both specific and total impurity content, and because of the many different test and evaluation techniques used, a clear, definitive picture of brittle fracture in chromium has not been forthcoming. However, many

Jan 1, 1964

By Nicholas J. Grant, John S. Benjamin, Bill C. Giessen

In the course of a study of hard particle-duc tile binder composite alloys, interest arose in the nature of the products of the reaction between the inter metallic compound NiAl and the binder niobium. No published information was then available. A program to

Jan 1, 1967

By Alexander L. Holley

THE 400-ton testing machine, ordered in June, 1875, by the United States Board appointed to test "iron, steel, and other metals," has lately been completed at the Watertown Arsenal, thoroughly proved and accepted by the Board. The excellence of the machine in every respect is more than satisfactory, and its accuracy is at first sight astonishing, although an investigation of its principles must show that if the weighing apparatus will weigh at all, it must do so with perfect accuracy, because all its movements are absolutely without friction. The proof experiments were numerous, and the effects of recoil after sudden ruptures at maximum loads, were watched with great care, but without much anxiety, because the weighing parts affected are by no means delicate in structure, and their motion is almost infinitely small. Among the tests were the following : A forged link of hard, wrought iron, 5 inches in diameter between the eyes, was slowly strained in tension, and broke short off with a loud report at 722,800 pounds. The diameter before breaking at the point of fracture was 5.04 inches; after breaking, 4.98 inches. In order to see if the weighing parts had been disturbed by the recoil, which was obviously near the greatest recoil the machine will ever suffer, a horse-hair was next tested ; it was 7-1000ths of an inch in diameter; it stretched 30 per cent., and broke at 1 pound. Other horse-hairs vary in tenacity between 1 and 2 pounds. Of course, the accuracy of the machine on such delicate specimens, and indeed on specimens having some hundreds of pounds tenacity, has been checked and proved by other weighing machines. A 5-inch round bar, turned down to 3 5/8 inches diameter along the centre, was pulled apart at 430,200 pounds tension. Then some more horse-hairs were tested ; also copper wires 19 1/2-1000ths of an inch in diameter, which averaged 25 pounds tenacity..

Jan 1, 1879

By W. F. Sullivan, J. R. Coleman

The use of radioisotopes in obtaining basic information on large scale industrial processing is illustrated with two examples. The first is concerned with the operating characteristics of a kiln scrubbing tower and the second with those of a Hardinge ore mill. The examples show the advantages associated with the industrial use of tracers as well as the limitations. The Atomic Energy Commission regulations governing the use of radioisotopes in this manner are also discussed. The nuclear properties of radioactive isotopes have provided a new technique for obtaining basic information on large scale industrial processing. A small portion of the process stream is made radioactive by mixing with a suitable radioisotope or by irradiation in a nuclear reactor. The "tagged" portion is then part of the normal process stream and can be followed by detection and measurement of the associated radioactivity. The advantages of radioactive tracing over other forms of tracers are well known, and include such factors as chemical similarity, capability of precise determination of very small quantities due to the high sensitivity of detection apparatus, and the absence of foreign element contamination of the final product. This report will illustrate two applications of the use of radioactive tracers in large scale industrial processing which have provided information that would have been hard to obtain by other means. The first is concerned with the operating characteristics of a kiln scrubbing tower and the second with those of a Hardinge ore mill. ATOMIC ENERGY COMMISSION REGULATIONS Atomic Energy Commission approval can be obtained by qualified personnel if the proposed quantity of radioactivity does not exceed AEC's standards for

Jan 1, 1965

By H. E. Doerr

The writer has been unable to find much information relative to tests made to determine the effect of forging on the specific density of steel. The opinion, however, among men engaged in the business, seems to be that forging greatly compresses or consolidates the steel. While such is doubtless the case with spongy or porous steel, the following experiments indicate that there can be little or no change in the density with steel initially free from cavities. Ten ingots of basic open-hearth steel cast as shown in Fig. 1 were used in the experiments. All the specimens were 0.53 carbon with all other elements the same, the analysis being determined from drillings taken midway between the center and outside of the upper end, as shown in Fig. 2. The specimens were selected from over one thousand ingots so that the tests could be comparative for the work done in forging only, but no two of the ingots were cast in the same heat. Each ingot remained in the mold approximately 30 min., when it was removed and sir-cooled. About 12 hr. later, when the temperature had been reduced to approximately that of the surrounding atmosphere, the head was discarded and the ingot heated in an oil furnace to approximately 2250" F. (1235" C). Approximately 1 min. was required to forge under the steam hammer to 1 1/4 in. (31.75 mm.), rough diameter, as shown by the dotted lines in Fig. 2. All ingots were allowed to air-cool after forging. Cylinders 1/2 in. (17.7 mm.) in diameter and 1/2 in. high were then turned from the forged and unforged parts of the ingots and numbered. The ten pairs of specimens were submitted to Louis E. Endsley, Professor of Railway Mechanical Engineering, University of Pittsburgh; A. N. Talbot, Professor of Applied Mechanics, University of Illinois; L. Z. Slater, chief chemist, Scullin Steel Co., St. Louis, Mo. NO information was furnished as to which specimens were forged or unforged and each laboratory used the same specimens, submitting the average of three independent determinations, a tabulation of which is shown in the accompanying table in which the laboratories are designated by the letters A, B, and C. While there is considerable difference in the individual determinations for a number of the specimens, the averages

Jan 1, 1920

By H. R. Aldrich

THIS paper presents some of the results obtained during the field season of 1919 while mapping, in detail, the stratigraphy of the Gogebic Range in Wisconsin. The detailed stratigraphic section for the range was first published, in 1919, by W. 0. Hotchkiss,1 State Geologist of Wisconsin. The idea of the continuity of the definite succession thus established was the result of underground work in the productive part of .the range in Michigan and Wisconsin, where most of the required data also were obtained. The bulk of the range in Wisconsin is heavily covered by drift; in fact, there is but one satisfactorily exposed section across the entire formation; few partial sections, and only scanty outcrops of any size. Evidently mapping of the detailed members of the formation could only be established at a few points; and if from these small areas the unexposed portions were to be mapped by projection, the only apparent method for projection was straight-line interpolation modified or supported by data from the scanty outcrops and from test workings. It was found that by tracing a magnetic line, the position of which in the formation may be determined from test pits and outcrops, the projection of that member through the drift-covered areas can be accomplished. The magnetic line serves as a datum horizon within the formation to which reference may be made in correlating outcrops and ledge matter thrown from test workings. The foot wall is easily located also, and from the two datum horizons thus available and the known proportional thickness of the several members in the type sections, outcrops and artificially exposed ledges can be correlated by lithological characteristics. As a result, the tracing-of magnetic lines became the basis of our work on the stratigraphy and we were able to carry the mapping of detailed members throughout the length of the range. It was found that the magnetic horizon at the base of the Tyler slate was most easily followed

Jan 8, 1920

By Rossiter W. Raymond

In the course of this address, President Raymond referred to the law, said to have been discovered at the French works of Terrenoire, that the amount of phosphorus may be increased without injury to steel, if the amount of carbon be proportionately decreased. The works named have been for more than a year, it is said, manufacturing in the open hearth, by the Martin process, steel rails containing as high as 0.35 per cent. of phosphorus, with about 0.15 per cent. of carbon, which were not found inferior to Bessemer rails. It is not claimed by the manager of the works that phosphorus is an ingredient to be preferred, or purposely introduced; but only that materials containing it (such as old iron rails, etc.), can be succesfully employed. Other parties have apparently a higher opinion still of the new manipulation, and are prepared to claim for " phosphorus steel" superior qualities. Mr. I. Lowthian Bell alluded to the subject in his recent address as President of the British Iron and Steel Institute, but without expressing a positive opinion. After pointing out that the commercial value of the process turned on the cheap manufacture of ferro-manganese, by means of which only could the necessary amount of manganese be introduced into the Martin bath, without increasing its contents of carbon, Mr. Raymond proceeded to say that the principle alleged to have been discovered at Terrenoire was already known years ago, in this country, at least. Not only had steel been manufactured here, containing high percentages of phosphorus, coupled with low percentages of carbon, and suitable for use in rails, boiler-plates, etc., but the reason of its surprising qualities had been distinctly surmised, if not widely proclaimed. The following analyses and extracts from private letters prove these assertions. Some of them assert a similar principle in .the case of wrought iron; but the analyses, and the remarks based upon them, have reference solely to the steel manufactured under the superintendence of Mr. Slade, at the works of the New Jersey Steel and Iron Company in Trenton.

By M. D. Flavel

The paper describes the physical aspects of the compression and impact crusher types along with the information needed to apply, install and operate them to best achieve designed performance levels. It reviews key performance parameters such as energy size relationships for crushing processes and how automation devices can optimize machine productivity. Weaknesses of existing application engineering methods are discussed. The use of pilot plant information and appropriate laboratory testing procedures are reviewed from the point of view of the application design engineer so that the best type of machine can be selected for a proposed installation.

Jan 1, 1982

By E. van Walsum

Tunneling methods through rock have, since the successful development of explosives, relied almost solely on blasting. Over the last ten years, rock-tunneling machines (moles) have been developed and some major projects have been carried out successfully with the use of such machines, which rely on the destruction of rock by mechanical means rather than blasting. Various other basically new methods are presently under study, such as the use of laser beams, water jets, etc. For practical purposes, there are presently only two methods commercially available: 1) blasting or 2) tunneling by mole. A contractor would choose at present either one method or the other. Both methods have their advantages and disadvantages (Fig. 1). The thought has occurred that the next practical development in rock- tunneling technology might be a combination of the best features of the mole technique and those of the blasting technique. A preliminary evaluation of this approach indicated that there is definitely a good potential for fruitful developments along these lines. My purpose is to place on record some of the thinking and some of the ideas which were developed along these lines and to point out certain areas where development efforts are required. In trying to find an improved tunneling technique, we looked in particular for the following qualities: 1) safety, 2) continuity, 3) uniformity, 4) automation, and 5) flexibility. TUNNELING BY BLASTING Conventional tunneling by means of blasting proceeds generally in recurring sequences of events: 1) drilling, 2) loading, 3) firing, 4) mucking-out, and supplementary operations (such as scaling and lining). These four operations (drilling, loading, firing, mucking) proceed one after another.

Jan 1, 1970

By T. Sterry Hunt

I have in a previous communication called the attention of the Institute to the geognostical relations of the crystalline iron ores belonging to the Eozoic racks of North America, at which time I noticed (1) those associated with the gneisses of the Laurentian series, (2) those of the crystalline schists of the Huronian, as seen in Northern Michigan and in many localities along the Appalachians; (3) those of Southeastern Missouri associated with petrosilex porphyries and schistose rocks, and presumed to be nearly of the same age with those of the Huronian schists; and (4) the highly titaniferous ores of the Norian or Labradorian series from Essex County, N. Y., and from various parts of Canada. It may here be remarked that, although the presence of titanium is most marked in the Norian ores, this objectionable element is sometimes found in the schistose ores of the Huronian, and to a lesser extent in certain Laurentian magnetites. The ores of each of these geological divisions have their individual peculiarities, which serve to distinguish them to such a degree that the magnetites and specular ores of the Laurentian are as dissimilar to those of the Huronian as are the crystalline silicated rocks of the two series. As it happens that these mineralogical dissimilarities correspond to diflerences in composition and in adaptability to different processes of manufacture, which, in the present condition of the iron industry, are objects of special consideration to metallurgists, it will be seen that these geognostical distinctions become of great practical importance. During the past year I was desired by the Geological Commissioners of Pennsylvania to devote a few weeks to certain geological studies in the eastern part of the State, in the course of which I was enabled to make, with regard to its crystalline iron ores, some observations to which I desire to call the attention of the Institute. I may mention, in passing, that the great South Mountain belt, from the Schuylkill to the Delaware, is composed of Laurentian rocks, in which are found the characteristic ores of the series like those of the Highlands of New Jersey and New York, and of the Adiron-

By Alphonse C. Van Besien, Arcy A., L. T. Larson, D&apos Shock, J. W. Peters, Ted H. Eyde, Dermot Ross-Brown, David L. Campbell, W. W. Dudley, John P. Bunch

Over the last several years, unfavorable economic and political pressures on open-pit mining have placed the industry in a generally defensive position. As a consequence, there have been changes in the traditional organizational and production methods to increase operating efficiency. For example, staff groups that were once used almost exclusively for production support are now being organized as mining/environmental specialists. These specialized groups are responsible for obtaining mining permits and insuring compliance with existing permit requirements. Permit issurance and renewal continues to grow as a major budget item in open-pit operations.

Jan 2, 1977

Jan 1, 1955

By N. G. Johnson

ALL of us are only too familiar with the fact that first the defense program, and finally the war, required vastly increased production from existing sources, and the discovery and development of new sources of minerals and metals. For this vast program, the explosives industry was well prepared. I use the term "well prepared" to cover all the phases of explosives service, which include formulation, design, manufacture, distribution, and application.

Jan 1, 1944

By D. L. Martin

The study of cobalt-platinum alloys has been of interest since they represent a class of permanent-magnet material in which the disorder-to-order transformation plays a controlling role. The magnetic properties of alloys in the range 40 to 60 at. pct have been found to be greatly influenced by composition and heat-treatment. The peak properties of 4700 coercive force and 9,000,000 gauss-oersteds energy product were obtained by controlled cooling and aging. These high values combined with ductility and machin-ability give the alloys useful characteristics although their high cost limits their application. THE cobalt-platinum alloys have been of interest in the study of permanent-magnet materials ever since the discovery by Jellinghaus that they had unusually high coerceive-force values.' The high coercive force was associated by Jellinghaus with the disorder-order reaction which occurred in these alloys. This was later verified by Gebhardt and Koster in a detailed study.2 An investigation of the structure, mechanism, and kinetics of the disorder-order transformation and resulting property changes in cobalt-platinum alloys has been in progress for some years. Certain phases of this study related to equilibrium rela- tions, and to the mechanism and kinetics of the ordering reaction have been published previously.3-5 In this paper, the results of the processing and heat-treatment studies on 40 to 60 at. pct CO alloys are presented. The magnetic properties have been found to be influenced greatly by the composition, by the cooling rate from the disordering treatment, and the final ordering time and temperature. Coercive force values, Hc, of 4700 oersteds and energy values, (BH)m, approaching 9,000,000 gauss-oersteds have been obtained by controlled cooling and ordering. PROCESSING OF THE ALLOYS The composition range of interest for permanent-magnet properties centers around the equiatomic composition Copt. In this region the alloys are dis-

Jan 1, 1959

By J. P. Dunlop

The fact is not.ablc though probably little known that thc Unitcd Statcls is the only nation obtaining and distributing through its Govcrn-ment burcaus any data pertaining to waste metals and drosses. Some foreign goverrlnlents do issuc reports relating to rnine or smelter production of prirrlar~ metals, but none gives in scope and detail t'he information published now by the U. S. Bureau of Mines and formerly by the U. S. Geological Survey; and this is despite the fact that the funds annually allotted for those purposes are insignificant in comparison with allotments for the preparation of data relating to other industries of like importance. The earliest data on the production of metals from secondary sources in the United States were contained in a press bulletin issued by the U. S. Geological Survey on Jan. 4, 1909. The information published was that for thc year 1907 obtained ant1 compiled by C. E. Siebenthal, who was one of the first to visualize the growing importance of the scrap-letal indust,ry. Thc Nationd Conscrvation Commission had emphasized its opinion that the known domestic supply of certain kinds of the morc important irietals was being rapidly marketed and that while there was no immediate cause for concern it was best to conserve such resources. Not only had there been a lanlentable lack of any data regarding the quantity of scrap inetals available or used but also gross carelessness and indifference in the segregation, collection, and effective use of scrap material. Siebenthal realized that even approximately correct statistics of recoveries from the more important base-metal scrap and drosses wcrc nearly as essential t,o both producers and consumers as the stat'istics of the output of primary metals. There were not then nor are there now sufficient funds for complete collection of data, nor was it considered the province of the Geological Survey t'o do more than determine approximately the recovery of secondary metals for use in supplementing those given for the primary metals. Undoubtedly the first bulletins issued did not give the full output, for it takes time to establish contacts for an inquiry covering so

By Robert H. Richards

THE Institute of Mining Engineers has shown so much interest in the educational problem of profitably combining theory and practice, that it seems especially appropriate to lay before its members the methods and aims of the mining laboratory of which I have charge, and in which one form of combination of hand with head work is now being tried. If anything may be contributed toward the solution of this problem by the discussion which follows, my purpose mill be attained. Whether it was wise or not to establish a mining school so far from the principal mining centres, does not now enter into the question. Given, a mining school already begun, how shall it be made most efficient in developing engineers who are trained to think for themselves as well as versed in the works of others ? This is the question with which we have had to deal. In considering the bearing of this laboratory work upon the students' preparation, it will be convenient to take it up under five different heads: 1. The methods and aims of the laboratory. 2. The advantage to students of having a part, at least, of their practical work in the curriculum of their school. 3. The advantage to be derived by mine; and works. 4. Degree of accuracy which may be attained in working ores on a small scale. 5. Reslts of work in the laboratory. 1. The Methods and Aims of the Laboratory.—During the May meeting of 1873, held in Boston, I had the privilege of reading before you a paper stating the plan; and aims of this laboratory. Since that time me have been constantly following out those plans, and are more than ever convineed that me are working in the right direction. We do not feel that the time we have spent has been in any sense thrown away. Perhaps the aims of the laboratory can be most clearly shown by illustration. Many young engineers have school thinking that they know everything. They go to the works, and expect to teach the superintendent something and the men a good deal, regardless of the fact that it is this spirit that has prejudiced workmen against schoolmen. They are often more trouble than they

Jan 1, 1879

By C. W. Reith

The development of production in West Texas during the year 1933 was largely confined to the expansion of proven areas, especially Ward County, Iatan and North Winkler. Wildcat activity was at a comparatively low ebb and resulted only in discoveries of probable minor importance in Ector County. The interest shown in deep wildcatting to test beds of pre-Permian age was a new development, which should soon throw light on the possibilities of deeper production from the present producing fields. The important pre-Permian tests of the year were: 1. Stanolind Oil and Gas Co., Todd No. 1, a unitized test, in north central Crockett County on a probable continuation of the Big Lake trend. The well encountered several showings of oil and penetrated an Ordovician section very similar to the productive zones at Big Lake, but was abandoned when sulfur water was encountered at 8041 feet. 2. Gulf Production Co., McElroy No. 103, in the McElroy Field, Upton County. The well was drilling at 8553 ft. at the close of the year in beds of probable pre-Permian age. The test is an important one because it should prove or disprove deep production in the Church-Fields-McElroy pools and also throw geologic light on the deep possibilities of other fields in the western part of the Permian Basin. 3. Humble Oil and Refining Co., White and Baker No. 1, in Pecos County, about 11 miles west of the Yates field. The well is on a nonproductive Permian high and should indicate the deep possibilities of the Yates field. At the end of the year, drilling had progressed to 7200 ft., where beds of pre-Permian age are believed to have been penetrated. The major fields in West Texas, in which present-day proration had its inception, were produced under increased restrictions. A date of importance in the proration history of the area was $ept. 8, 1933, when the Railroad Commission issued an order placing all producing wells under proration. The severe reductions in total outlet made during 1933 were well compensated for by a more than threefold increase in the price of crude oil. Acid treatment was one of the general engineering developments of interest. The work had not progressed sufficie~ltly at the close of 1933

Jan 1, 1934