Search Documents

By D. E. Pickett, E. G. Joe

In accordance with good industrial practice, Canadian metallic-ore concentration plants have always recycled a high proportion of process water to save reagents, save power, conserve water resources, and to protect the community water supplies, to give only a few reasons. In the last few years there has been awakened public concern for the environment and, consequently, government regulations have been added as additional reasons. Present recycling practices are summarized as a basis for improved plant design and operating procedures and for further research. In addition, an attempt is made to determine why plants do not recycle water in certain situations. Although not all Canadian mills are covered, the many examples given indicate the problems and the effort being made to solve them. Wherever available, the chemical quality of the water and the process requirements are indicated as well as the other parameters affecting water recycling at each operation.

Jan 1, 1975

Discussion of the paper of H. R. Barnhurst, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2523 to 2532. H. R. BARNHURST :-I would say that in that experimental furnace we were trying to adopt the proper form for burning low-volatile coal. I was enabled on one occasion to burn coke having 15 per cent. ash. Tailings, or washings from the preparation of coal for by-product coke ovens, which came to me 52 per cent. ash, were burned without any trouble. So that ash really might be regarded as not burning, but simply diluting the fuel that was there, without doing any particular harm except that we had to put in more of the material to get the same quantity of heat. With anthracite, I burned coal right along with from 24 to 27 per cent. ash, but it took a furnace of peculiar form in which the products of combustion had to be diverted to the point of entrance of the fuel. With an ordinary furnace the fuel is deflagrated by its surroundings as soon as it enters the furnace. In a cement furnace this action is secured by the hot clinker passing clown, and the walls of the kiln are heated upon contact with it, revolving as they do', so that deflagration occurs very quickly in a cement kiln. Deflagration would occur very quickly in an open-hearth furnace also. There is no trouble in burning anthracite coal under those conditions for three or four days successively. It should be very well dried and thoroughly pulverized. Aside from that, there is no trouble. WILLIAM A. EVANS,* Boston, Mass. :-In a 52 per cent. ash, or any high-ash coal, what disposition is made of the ash ? MR. BARNHURST :-Most of it went out through the flues. Some of it remained in the boiler and a quantity remained in the furnace. We raked it out and carried it away. MR. EVANS :-Do you experience the forming of stags in flues with such coal as that?

Jan 12, 1913

By Stanly A. Easton, H. M. Childs

Methods evolved at Kellogg have had primarily in view the safety of workmen and complete recovery of the ore; it is believed that these results have been secured at a minimum cost. The ore in the Bunker Hill mine is of good grade, relatively speaking; much of it is quite rich and no mining method would be successful which did not recover all of the ore. It would be possible to work certain of the orebodies by shrinkage methods, or some form of top-slicing, at probably lower costs than by the methods now applied, but the shapes of the orebodies are so irregular that satisfactory extraction of the ore in all its ramifications would be extremely difficult. In past years, much high-grade ore has been lost in blasting, due to the unskilful use of powder in a galena ore, which, by reason of its brittle-ness and great weight, tends to scatter widely. Any method by which large masses of ore and waste are broken together will result in an imperfect recovery of the ore, and whenever large masses are broken, ore and waste will unavoidably fall down together; ore and waste thus become entangled and, although a pile of broken material may seem to have been well picked over, quantities of ore will inevitably be lost. This fact has been shown by persons reworking the filling in stopes that were mined by methods defective in the foregoing particulars. Safety of the men is secured by avoiding large openings, and by working mainly under timber, and at small faces at close range and easily inspected. In former years the principal source of serious accidents was "falls of ground;" it is now over seven years since a serious accident has occurred from this cause. The most prolific source of accidents during recent years has been "timber and tools," workmen being struck by timbers passed into the stope from the level above; this danger has been greatly reduced by compressed-air warning whistles and the fencing in of dangerous areas. The lead-silver ore of the Bunker Hill and Sullivan and affiliated mines is found in bodies of almost every shape, although vertical or nearly

Jan 1, 1925

By A. P. Coldren, V. Biss

SINCE the r ? a transformation rates of many carbon-free ferrous alloys and low-carbon alloy steels are relatively fast, conventional equipment is not suitable for the dilatometric determination of continuous cooling transformation diagrams. On the other hand, a method based on metallographic analysis of quenched specimens would not be practicable because the various products of shear-dominated transformation are essentially indistinguishable in low-carbon iron-base alloys. Both problems may be avoided by a thermal analysis method employing gas quenching of small specimens austenitized in vacuo. The laboratory equipment employed in the present study consisted of a Tektronix Type 564 Storage Screen Oscilloscope and a Kinney high-vacuum evaporator, modified as shown in Fig. 1, to permit heating a small specimen and cooling it slowly by programmed cooling or rapidly (up to about 8000°F per sec) by a controlled quench with helium gas. The oscilloscope records the electromotive force of a 40-gage (0.003-in.-diam) Chromel-Alumel thermocouple in the specimen during cooling. The temperature at which the cooling curve begins to show the influence of the heat produced by the phase change in the specimen was arbitrarily taken as the transformation-start temperature.*

Jan 1, 1970

By H. Shaw

IT is now generally recognized that the gravitational method of geophysical surveying is a valuable aid in elucidating the geological structure of the subsoil and enables the practical geologist to deduce the presence of useful deposits. The particular suitability of the torsion balance to the location of large and important subterranean structures has given rise to a wide application of this method by many of the important oil companies in their search for future supplies, and so intense have been these efforts that little has been heard of the method in other connections, with the exception of occasional references to its application in the location of hidden deposits of metallic ores, salt and lignite, and a number of accounts of its use in the elucidation of geological structures. Its success in the location of salt domes is well known, and establishes it as one of the most important of the geophysical methods, especially for the indirect location of oil. In the British Isles, however, no large occurrence of oil is likely to be revealed, and here the practical application of the gravitational method has been restricted almost entirely to the search for ores. This type of survey possesses well marked characteristics, and presents a gravitational problem that has necessitated the development of a special and probably unusual plan of campaign, full details of which it is hoped will shortly be published. The problems and difficulties encountered in this work are of necessity fundamentally related to those met with in the search for oil by means of the torsion balance, but they also possess several special and distinctive features which undoubtedly differentiate them from the obstacles confronting the oil prospector, and which call for special consideration and treatment.

Jan 1, 1928

By J. W. Powell

A Federal statute, enacted several years since, provides for the preparation of a geologic map of the United States. There are three requisites for a geologic map. The first is a suitable base- or surface-map upon which the rock-formations may be platted by means of conventions ; the second is a classification of the rocks and formations, and the third is a system of conventions by which the rocks and formations may be represented on the map. When the work of the Federal bureau created to prepare the geologic map was commenced, a topographic survey of the country was undertaken for the purpose of making maps suitable for the use of geologists in the field and for the representation of the geology; and this work has ever since been continued. The surveys have now extended over about one-fifth of the national domain, and are mapped on a series of atlas-sheets, each constituting a section of the great map of the United States. About 700 of these atlas-sheets are completed. They are in extended use among engineers, miners, prospectors, map-publishers and educators, and are thus widely known; moreover, these base-maps have been exhibited, described and discussed at meetings of the Institute, and thus do not require detailed consideration. Classification of Bocks and Formations. Modern classification is designed to express natural relation. In the beginning of observational science, or natural science, objects were discriminated and grouped by differences and resemblances; but at first the differences and resemblances recognized in the classification were external, even superficia1,'and often confined to single features. Later, groups of features and characteristics, both external and internal, were recognized as the basis of classification ; and of recent years, throughout the entire domain of biology, and to a considerable extent in the kindred sciences, classification is based not

Jan 1, 1893

By H. M. Morse

Mississippi, during the year 1941, experienced the greatest diversity of oil activity since the beginning of oil interest in the state—core tests for exploration, core tests for sulphur, continued drilling at Tinsley for production, and wildcatting, which brought to light two new oil fields and two new salt domes. There were 45 wildcat wells drilled in 1941, which showed greater results and findings geologically than the 85 drilled in 1940. Tinsley Oil Field (Yazoo County).—The Tinsley oil field, with its boundaries fairly well defined now, is 8 miles long and 3 miles wide at its widest point. During the past year 213 producing wells were completed, which brought the total number of producers in the field by the end of 1941 to 325 wells. Seven producing sands have been logged, with a total average thickness of 30 ft. of oil sand. The producing formations are the Selma, Eutaw and Tuscaloosa. The average total depth of the wells is 5012 ft. The average gravity of the oil is 35.4°. Production for 1941 was approximately 15,500,000 bbl. of oil. Vaughan-Pickens Oil Field (Yazoo County).—At the end of 1941 only three wells were Producing in this field, the fourth having been abandoned. The total production for the field for the year was approximately 250,000 bbl. of oil. The producing sand is the Wilburn, in the Eutaw formation. Cary Field (Sharkey County).—The British American Oil Producing Co. completed, on Sept. I, 1941, its F. B. Houston No. A-I well, sec. 23, T. 11 N., R. 7 W. It is

Jan 1, 1942

By H. M. Morse

Mississippi, during the year 1941, experienced the greatest diversity of oil activity since the beginning of oil interest in the state—core tests for exploration, core tests for sulphur, continued drilling at Tinsley for production, and wildcatting, which brought to light two new oil fields and two new salt domes. There were 45 wildcat wells drilled in 1941, which showed greater results and findings geologically than the 85 drilled in 1940. Tinsley Oil Field (Yazoo County).—The Tinsley oil field, with its boundaries fairly well defined now, is 8 miles long and 3 miles wide at its widest point. During the past year 213 producing wells were completed, which brought the total number of producers in the field by the end of 1941 to 325 wells. Seven producing sands have been logged, with a total average thickness of 30 ft. of oil sand. The producing formations are the Selma, Eutaw and Tuscaloosa. The average total depth of the wells is 5012 ft. The average gravity of the oil is 35.4°. Production for 1941 was approximately 15,500,000 bbl. of oil. Vaughan-Pickens Oil Field (Yazoo County).—At the end of 1941 only three wells were Producing in this field, the fourth having been abandoned. The total production for the field for the year was approximately 250,000 bbl. of oil. The producing sand is the Wilburn, in the Eutaw formation. Cary Field (Sharkey County).—The British American Oil Producing Co. completed, on Sept. I, 1941, its F. B. Houston No. A-I well, sec. 23, T. 11 N., R. 7 W. It is

Jan 1, 1942

By Earl Chairman Oliver

The major development in stabilization of the oil industry during 1933 was the transition in the United States from state control to federal control in many of the functions that government is presumed to exercise. A brief review of the influences leading to that transition is given here to suggest its significance and to assist in forecasting its further development. Bitumens were known to the ancients and have been applied to minor uses since earliest historic times, but it was not until after the discovery of oil in considerable quantities near Titusville, Pennsylvania, in 1859 that it was made the basis of extensive commercial undertakings. In 1859 little was known about the origin of oil and gas, the nature of these deposits, and the physical laws that controlled their accumulation. Scientists soon began to study them, but 50 years or more of active oil-field development had elapsed before sufficient geological information had been accumulated to point the way toward efficient recovery of these products. In fact, only within the past five years has the function of reservoir energy become widely understood, yet it is a primary factor in oil recovery. discovery near Titusville, this infant industry has developed into an industrial giant. In complete ignorance of their destructive effect, wasteful development methods were initiated in Oil Creek and these became industrial habits. These habits in turn became oil and gas law. Under that law vast sums of money have been expended, rights have become vested and development methods fastened on a great industry that not only bring upon it periodic demoralization but cause ruthless destruction of the nation's reserves of these important natural resources. This is occurring in the midst of a petroleum era when oil is essential to the nation's security, its industrial supremacy, and the personal convenience of every citizen. Its conservation, therefore, has become a question of grave national concern. Conflict between PHysical Facts and Oil Law This destruction of an important natural resource and periodic demoralization of a vast industry can be halted only by readjusting oil

Jan 1, 1934

By John Garcia

COAL MINING, as well as all the other major in-dustries of Russia, is controlled by the Soviet Gov-ernment by means of organizations in each dis-trict, known as "Trusts," such as the "Kisel Coal Trust" in the Urals, the "Donugol Trust" in the Ukraine, etc., and each Trust functions as a unit, reporting direct to the chief of the department of the government at Moscow. The responsible head of each Trust is usually a mem-ber of the Communist party and, filtered through his organization, one generally finds a fair proportion of Communists in "key" or important positions, such as purchasing agents and local managers or superinten-dents, but in the majority of places requiring technical or professional knowledge, or trained brains and ex-perience, little or no attention is paid to a man's political opinion provided, of course, he "behaves himself." These different Trusts were authorized or ordered by the Central Committee at Moscow to investigate the methods of mining and type of mines developed in all other coal producing, countries of the world, and after a period of several years of intensive investigation and study reported back to headquarters that the modern American mines were the most efficient, recommending that the program for the rehabilitation of the Russian coal mining industry should follow the lines of American practice. The Trusts were then authorized to negotiate with American engineering firms for technical service for mine designs, and invited Americans to send commis-sions to Russia to prepare and submit to the Technical Council one or more projects for a complete modern American-type operation adapted to the local conditions. A "project" is a preliminary set of designs on the entire mine, top and bottom, with specifications. cost estimates, production costs, schedule of operation, budget of expen-diture, etc., and is quite an elaborate and sizable under-taking-I might say, it took six of us working tooth and nail for over three months to finish our first project.

Jan 3, 1928

By Jr. W. L . Phillips

The deformation and fracture characteristics of lithium-fluoride single crystals stressed in compression at room temperature have been studied. In as-cleaved specimens the stress-strain curves were variable; two types of {110} fractures were observed in the vicinity of kink bands. The stress-strain curves of annealed crystals were reproducible; {100} cracks formed which propagated along the (100) and (110) planes. The deformation and fracture characteristics were affected by quenching and X-ray irradiation. STUDY of the mechanical behavior of nonmetallic materials has received considerable impetus in recent years because of the need to overcome the problem of brittleness before the refractory properties of nonmetallics can be fully exploited. Ionic crystals provide a convenient and simplified starting point from which to study the deformation and fracture processes in nonmetallic materials. Early investigations of the mechanical behavior of non-metals were restricted largely to determinations of the crystallographic indices of the cleavage and fracture planes and the glide and twinning elements. Until recently, only occasional systematic studies of the deformation characteristics of non-metals have been made; and investigations of the forces necessary to initiate plastic deformation and the factors which affect the flow characteristics have been restricted largely to studies of sodium chloride'-7 , magnesium oxides-l3 and lithium fluoride. 14-22 Fracture studies on alkali halide and metal oxide single crystals have been limited despite the fact that these materials have a number of advantages for fracture studies. Because they are transparent, the cracks which form can be viewed in three dimensions instead of in two dimensions as in metals. Also, they exhibit stress birefringence under polarized illumination, which enables the internal stress pattern and, therefore, the distribution of dislocations to be examined in the vicinity of the fracture. Early workers1-4 have shown that ionic crystals with a cubic structure fracture in tension along the (100) plane normal to the applied stress. These fractures were brittle at room temperature and propagated very rapidly across the cross section of the crystal. More recently, Stokes, Johnston, and Lil0 have studied crack formation in compressed magnesium-oxide single crystals. They found that the cracks, which were observed after about 3 pct strain, formed in the region of a kink band and lay on conjugate (110) slip planes instead of the usual(100) cleavage plane. Two different types of cracks were noted: stroh23 and secondary. The Stroh cracks did not exist merely on the surface but extended through the specimen in the form of tiny slits. A secondary

Jan 1, 1962

By H. H. Lowry

SCIENCE attracts the attention and interest of an individual or an industry in general only in proportion to the apparent direct application to its immediate welfare or benefit. Engineering accomplishments, as applied science, therefore receive more recognition than the scientific discoveries on which they are based. Even self-evident truth needs endless repetition before recognition: engineering as applied science cannot advance beyond the science on which it is founded. Scientific research, and discovery, is sometimes forced by the limitations recognized by those active in its development for the use of society and industry and sometimes results from an apparently superficially illogical curiosity about natural phenomena. Research has received inadequate support except in industries born in the laboratory, the chemical and electrical industries, from which many lessons might well be drawn by their elder associates. The rapid growth of these industries has been largely due to close cooperation of scientists and engineers. Most rapid advance is made when the research worker and the engineer keep in close touch with each other's ideas and problems. Many of the developments of modern industry are based on dis-coveries buried for years in scientific journals because the "time was not ripe" at their discovery. The situation with regard to utilization of coal is quite the opposite. The fundamental facts in regard to the scientific aspects of the problem of developing the energy from coal are scarcely known. The engineer, without much scientific cooperation, has accom-plished much in increasing the number of kilowatt-hours per pound of coal from 0.31 in 1919 to 0.69 in 1934, in increasing the 1000 gross ton-miles of freight hauled from 6.1 to 8.3 per ton of coal in the same period, in fuel economy in production of coke, and in developing the production of motor fuel in Germany and England by hydrogenation of coal. This lack of scientific research on the utilization of our most important natural resource, coal, has been due undoubtedly in large part to the reluctance of investigators to study the interrelationships involved in, the complicated processes in which coal is used. These complexities are made

Jan 1, 1936

By Kirtland Marsh

THE manufacture of gas masks by the Chemical Warfare Service, U. S. A., required preparation of the carbon used in the canisters. The largest plant for the production of this carbon was situated at the works of the Astoria Light, Heat and Power Co., at Astoria, N. Y.; this paper will deal1 with the pyrometry equipment at that plant. Commercial charcoal was found unsuitable for use in gas masks because of its low power of absorption and its poor resistance to abrasion. The best raw material for the production of carbon was found to be coconut shells, but any kind of nut shells or fruit pits were used when sufficient quantities of coconut shells could not be obtained. The shells were first carbonized in retorts, the carbon was then crushed and screened between 8 and 16 mesh, and finally submitted to a special heat-treatment in air; steam treatment was later substituted for treatment in air. The production of gas-mask carbon on a commercial scale was begun at Astoria about Aug. 1, 1917. Temperature control was essential during the initial carbonization of the shells, as well as during the air or steam treatment, and pyrometers were installed for this purpose. The installation and maintenance of all pyrometry equipment was done by the pyrometry department, consisting of an officer in charge, an assistant, and two men. A special pyrometry laboratory was maintained in which all repairs were made.

Jan 9, 1919

By Franklin J. Stermole

INTRODUCTION Economic evaluation of an open pit mine is similar to the economic analysis of any major investment project in any industry. It requires (1) taking into account all of the costs and revenues that are estimated to be incurred over the economic life of the project; (2) crediting the project with all the tax savings and tax credits that will be realized over the project life from tax deductions and credits related to various project costs; (3) charging the project with all taxes to be paid on taxable income over the project life; and (4) properly accounting for the time value of money for all project costs, revenues, taxes, tax savings, and tax credits when making the overall project economic evaluation. These considerations must be taken into account for any valid method of economic analysis such as discounted cash flow rate of return (DCFROR) or net present value (NPV) analyses. All economic analyses fall into one of two categories. ( 1 ) comparison of income-producing alternatives, or (2) comparison of service-producing alternatives. The analysis of alternatives in either of these categories can be made by using correctly any of five basic economic evaluation approaches which are. ( 1 ) present value, annual value, (3) future value, (4) rate of return (ROR) , and (5 ) break-even analysis. Of these evaluation techniques, DCFROR and NPV analyses are used most widely for evaluating income-producing alternatives while present worth cost and equivalent annual cost analyses are used most often for the evaluation of service-producing alternatives. In this chapter income- producing alternative analysis is emphasized, so DCF- ROR and NPV are utilized for evaluating the case studies presented.

Jan 1, 1979

By James Norman, O. C. Ralston, John Dasher

MOST mineral products are used in the finely divided state, but some are sold in larger sizes. Coal, gravel, metallurgical fluorspar, phosphate rock, hematite, chromite, and other products are sold in sizes coarser than can be treated by many mineral-dressing methods. Gravity separation of coarser sizes by log washing and jigging is probably as ancient as any process now in use. The performance of jigs on a feed with sufficient difference in density of the minerals is excellent, but many families of minerals are too similar in density to be separated effectively by this method. The use of heavy suspensions of fine solids to separate coarse coal from bone and slate has been in use for some years. This separation by sink-and-float was limited until recently to light minerals. Development of galena and ferrosilicon as suspension media, by Minerals Beneficiation, Inc., at Mascot, Tenn., Pitcher, Okla., and Crosby, Minn., under patents granted during and since 1938, has permitted excellent results to be obtained on minerals of very similar densities up to 3.3. This process has been put in the hands of American Cyanamid Co. for exploitation, and further research now in progress may increase the density of suspension obtainable so that separation, at a density of 4,0 may be practicable before this is published. The Huntington-Heberlein dense-medium process, developed in England, is also being commercialized in the United States by Sink and Float Corporation. Du Pont has developed a sink-and-float separation using halogenated hydrocarbons as parting liquids; at this writing, the method is used commercially only on coal but has been successful in the pilot plant on many other minerals using tetrabromethane at densities up to 2.95. While these processes were being developed to extend the range of separation by difference in density to the coarser sizes, the Bureau of Mines was engaged in developing a process that will extend the range of separation by difference in wettability up to 2-in, size. War work has pushed aside its further development indefinitely. The results are published here with the hope that some use may be suggested that will justify post-war development, and so that readers that may be able to make immediate use of the scheme may have the information. EARLIER WORK It has been known since the time of Herodotus (B.C. 484(?)-425) that water-repellent particles will adhere to sticky surfaces. That early historian reports the

Jan 1, 1942

By David R. Mitchell

THE mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are wasted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Several chemical companies in the East became concerned about supplies of pyrite early in 1943, but by late summer of that year the situation had eased. If for no other reason than national security and self-sufficiency during war-time, methods of recovering pyrite from coal-mine refuse should be worked out and made available to coal-mine operators who are potential producers of pyrite. Eastern sulphuric-acid plants are particularly likely to have their sources of raw material blocked by war conditions, so that special studies to determine where supplies of pyrite can be obtained for these plants from inland sources are desirable. Davis's1 summarization of conditions during World War I gives the following facts: During those years, the shortage of pyrite became acute. Shipments of hand-picked pyrite were made from a number of coal mines in Illinois, Indiana, western Kentucky, Ohio and Pennsylvania. A mechanical concentrating plant for separating pyrite from picking-table refuse was built at Danville, Ill., and operated for several years, and a small pyrite-concentrating plant treating washery refuse near Gillespie, Ill., operated for several months in 1918. The Consolidation Coal Co. of Fairmont, W. Va., constructed and operated a sulphuric-acid plant using pyrite recovered from coal-mine refuse. The U. S. Bureau of Mines during 1917-1919 made a comprehensive survey of pyrite-production possibilities from coal mines and estimated that there was a potential yearly production of 435,000 tons from Ohio and Pennsylvania and 928,000 tons from Kansas, Missouri, Iowa, Illinois, and Indiana mines. This estimate included only mines that could produce one per cent or more of their coal production as pyrite containing a minimum of 40 per cent sulphur. PYRITE PRODUCTION According to the Minerals Yearbook,2 approximately 660,000 long tons of pyrite was produced in the United States in 1941, with an average sulphur content of 42 per cent. The average value f.o.b. mines was $3.09 per long ton. Spanish pyrite, 48 per cent sulphur minimum, was quoted at 12 cents a unit c.i.f. U. S. ports, equal to $5.76 a ton for shipments of minimum sulphur content. Most of the pyrite produced in the United States is obtained as a by-product in the dressing of copper and zinc ores. Metal mines in the East making pyrite concentrate for the market or use in company-operated sulphuric-acid plants

Jan 1, 1944

By Wilford S. Wright

FOR the past four years the management of the Black Hawk Consolidated Mines plant at Mogollon has conscientiously kept accurate records pertaining to cost of operation and the performance of certain equipment. These records have been valuable in coordinating the work in the mine, mill and power plant. Also, as to quantity and kind of equipment and supplies most suitable from the standpoint of economy and dependable operation, they have served as a guide. Through comparison with records at other mines, where the same things are being done in a different way, they have pointed out mistakes to be avoided. No outstanding accomplishments, either in costs or performances, are revealed; in fact, some of the results are perhaps quite inferior to those obtained at similar plants, but it is with the thought that more records should be published for the benefit of the mining profession that the author presents these data. To other operators and to mining engineers who are called upon to make estimates for prospective operations, the information herein should be helpful. GENERAL CONDITIONS Mogollon is in the southern part of Catron County, southwestern New Mexico. It lies near the western border of the Mogollon Range, 14 miles east of the Arizona line. Silver City, 80 miles to the southeast, is the nearest railroad point. The connecting road, over which supplies are hauled into camp by trucks, is an improved highway for about 50 miles; the remainder consists of graveled roads and unimproved steep mountain grades. One general supply truck and one tank truck make daily round trips. Hauling of supplies to the mine has cost at the rate of $0.08 per ton-mile; or, on the basis of ore production, $0.30 per ton mined. Lumber, hauled in from local mills, has cost an average of $30.00 per 1000 board feet, $8.50 of which has been for hauling. The annual consumption averages 108,000 board feet. Lime, hauled from a plant in Arizona, is about the only other item not brought out from Silver City. Fuel oil for the generation of power is the item of greatest hauling expense, the f.o.b. Mogollon cost of approximately $0.06 per gal. being nearly twice the f.o.b. refinery price. Water for power plant, mill and camp use flows to camp storage tanks through a 4-in. pipe line from a spring and intake 3 miles up Silver Creek Canyon. A few times, particularly in the month of June, mill operations have been suspended for two or three days because of water shortage. MINING CONDITIONS During the years 1938, 1939, 1940 and 1941, the mine produced 230,059 dry tons

Jan 1, 1943

By G. H. Ashley

THE Pittsburgh coal bed stands today: as probably the largest contributor of wealth of any single mineral deposit in the world. If it is not, what other deposit is? To the present it has contributed more than 2,530,000,000 tons of high-grade coal from Pennsylvania alone, worth nearly $4,000,000,000. Since 1910 it has added more than $2,500,000,000 to the value of Pennsylvania's mineral output. There is estimated to be about three times as much coal still in this bed as has been mined. To realize the full value of this wonderful bed it must be remembered that the figures given are for one State only. To them should be added the figures for the same bed from West Virginia, Ohio and Maryland. Furthermore, as known by man, this great deposit is only a fraction of its original whole. Outliers in Somerset County, Pa., indicate that its original extent in Pennsylvania in an east and west direction was more than two times its present extent. Add to that the northward extension as indicated by outliers in northern Allegheny, Armstrong and Indiana counties,, and it seems safe to say that its original extent was not less than three times the area at present underlain by it. And as the subjacent beds of the Allegheny group are found still further eastward and northward, it is at least a possibility that it originally covered an area many times its present area.

Jan 10, 1926

By Frank Robertson Van Horn

In June, 1911, the writer spent a few days in studying the economic geology of the vicinity of Park City. During this rather hurried visit a number of specimens of ore were collected, which have since been examind. The results of these investigations show that bournonite (PbCu-SbSa) is present in the ores in greater or less quantity. This fact has never before been reported, as far as can be learned. The failure to recognize this mineral is due to its similarity to tetrahedrite, with which it has probably been confused during a long period of years. Jamesonite (Pb2sb2s6) has been reported from the region in a rather doubtful manner, but the writer has seen it in notable amounts from several mines, and can offer the first analysis of this mineral from the district. Calamine (HzZn2SiO5) was found at one mine and has never been ecognized and reported from the district. Geogbaphy and Geology Park City, Utah, is located at an elevation of about 7,000 ft. above sea level on the eastern slope of the Wasatch mountains. It is situated approximately 25 miles southeast of Salt Lake City. ' The geology and ore deposits have been described in detail by Bout well and Woolsey.' The mines visited are situated south-southeast from the town. The Silver King Coalition mine is located in Woodside gulch about 1 mile southeast of Park City, at an altitude of about 8,100 ft. The other mines visited were the Daly West and Quincy, which are in Empire canyon about 2 miles sontheast of the town, at elevations of 8,300 to 8,500 ft. respectively. The Daly Judge tunnel goes into the mountain from Empire canyon about 1 mile south of the city, at an altitude of 7,700ft.

Jan 1, 1915

By C. M. Young

Wherever salt is extracted from the ground as an artificial brine produced by pumping down fresh water to dissolve the salt, subsidence of the overburden is a possibility, though apparently few cases of such subsidence have been noted and detailed records are wanting. This description is intended as a record of subsidence that may permit the forcasting of similar occurrences in other cases; the data were supplied largely by R. B. Lee, city engineer of Hutchinson, Kans. About eleven years ago, ground movement occurred at a neighboring salt plant, when the surface assumed the form of a shallow funnel. Movement was probably due to a flow of sand into a well through a poor seal or a broken casing. The salt deposit increases in thickness from the east until at Hutchinson, where the subsidence occurred, it is about 310 ft. thick. The interbedded layers of shale vary in thickness from mere traces to about 7 ft. While knowledge of the shale content of the beds is not exact, the log of a shaft 3 miles east of Hutchinson indicates that shale forms about 25 per cent. of the total thickness. This shaft does not reach the bottom of the salt by about 60 ft., but there is no reason to think that the lower part of the bed is different from the upper. Logs of wells sunk to the bottom are not sufficiently detailed to be of much value. Above the salt is the shale of the well-known Red Beds. The thickness of this is variable, principally because of its eroded surface, but at the mine it is 340 ft. This shale is variable in character and strength, but contains no strong members of limestone or sandstone. If the support is removed, very probably it will subside. The Arkansas River flows across the salt district and Hutchinson is situated on the flood plain. Between the top soil, which is about 8 ft. thick, and the shale is 60 to 100 ft. of water-bearing sand and gravel. The process of removing salt, at least in the case of the earlier wells with which we are concerned, is as follows: An 8-in. hole is put down through the sand and gravel by means of a drive pipe, which is bedded in the shale. Prom the top of the shale, a 6411. hole is drilled through the shale, to, or nearly to, the bottom of the salt. Casing is put in to a depth of about 140 ft. to shut off a water-bearing layer in the shale.

Jan 1, 1927