Search Documents

By J. C. Danko, R. D. Stout, A. H. Holtzman

The deformation characteristics of pearlite have been studied by light and electron microscopy.1,2 In the electron-microscopic work, deformation was found to take place by 1) ferrite slip which is parallel to the lamellae, 2) slip transverse to the lamellae with both cementite and ferrite deforming, and 3) ferrite-cementite interfacial slip. The transverse slip gives a step-like appearance to the lamellae in light microscopic work. It was thought that spheroidization of deformed pearlite would commence at the regions of maximum cementite deformation, the "stepped" areas. Although there is no possibility for seeing slip in the microstructure if the specimen is polished after deformation, the step-like appearance of the lamellae clearly indicates the transverse deformation. Thus, the areas of cementite deformation are apparent after polishing and the effect of deformed areas on spheroidization may be studied by the usual metallographic techniques. This note reports the result of a metallographic investigation which substantiates that spheroidization begins in the "stepped" areas. An AISI 1080 steel was normalized, re-austeni-tized at 1040°C, and isothermally transformed at 700 ± 4°C for 4 hr. Cubes, 5 mm to a side, were compressed between parallel plates to strains of 20, 40, and 50 pct. After deformation, specimens were heated to 600, 650, and 700°C; withdrawn at increasing time intervals and examined metallo-graphically for the percentage and distribution of spheroidite. The percentage of spheroidite was determined by lineal analysis. A micro structural region considered as spheroidized was one in which a lamellar skeleton was not distinguishable. Table I gives the times necessary for 95 pct spheroidization for each condition of strain and annealing temperature. Fig. 1 shows the microstructure of coarse pearlite compressed 20 pct, then polished and etched. Here the lamellae form a step by bending at two

Jan 1, 1959

By R. Grierson, R. N. Parkins

The m.echanica1 properties, at high lzomologous temperatures, of the intermetallic compounds InzBi and Mg17A112 were measured as a .function of temperature, applied strain rate, previous thermal and mechanical history, and composition. Mgl,Al12 was investigated ilz compression, whereas Zn,Bi was investigated in tension. A decrease inflow stress with increasing strain was observed jor both alloys. The results obtained are discussed in terms of the dislocation-multiplication processes in these materials. MANY intermetallic compounds are reported to undergo a brittle-ductile transition at high homologous temperatures.' There is evidence in the literature that some of these compounds exhibit a large yield drop when plastically deformed.'j3 Both of these forms of behavior are shown by the covalent elements germanium and silicon4,5 and also by certain ionic compounds.8 The present work is a study of the deformation, at high homologous temperatures (>2/3 Tm), of two intermetallic compounds, In2Bi and Mg17Al12. InzBi has a disordered hexagonal structure7 (c/a = 0.598) and a solubility range of 32.3 — 33.2 at. pct Bi.8 It has a melting range from 72° to 89°C. Mg17Al12 has an ordered bcc (A12 type)7 structure and exists over the range 50 to 60 at. pct Mg8 with a melting range from 437° to 462°C. We have been unable to find any reference to previous investigations of the mechanical properties of BiIn,. Novikovg has reported that cast samples of Mg17A112 show ductility, when bend-tested, at temperatures above 380°C. EXPERIMENTAL Ingots of In2Bi and Mg17Al12 were melted under an argon atmosphere and cast, in situ, in a graphite crucible. The materials used were of 99.99 pct purity. The alloys prepared contained 66.9 at. pct In in the case of In2Bi and 58.4 at. pct Mg in the case of m17A112. The ingots were homogenized and then extruded. Two-in.-diam Mg17Al12 ingots were extruded at 375°C to give 3/8-in.-diam rod. The rate of formation of this rod was 0.25 in. per min. One-in.-diam InzBi ingots were extruded at 20°C, using a rate of 1 in. per min, to give 1/8-in.-diam rod. In both cases the extruded rod had a recrystal- lized, fine-grain, structure. (For Mg17Al12, d = 11.2 µ; for BiIn2, d = 22 µ.) Mechanical-property determinations were made in a hard-beam machine, in tension in the case of In2Bi and in compression with Mgl7Al12. The tensile tests were on specimens having a gage length of 1.1/2 in. and a diameter of 1/8 in. The compression tests on Ml7A112 were on specimens of 3/8 in. diam by 3/8 in. high and the ends were coated with poly-tetrafluorethylene to minimize friction. RESULTS In2Bi. Fig. 1 shows, particularly at the higher applied strain rates, that In2Bi exhibits a marked yield drop as the deformation increases to about 2 pct, after which the material shows neither hardening nor softening up to 15 pct strain. The magnitude of the yield drop, the stress in the region of flow under constant stress (the stress plateau), and the 0.5 pct proof stress were all dependent upon the applied strain rate according to an expression of the form

Jan 1, 1965

By Y. Oinouye, H. Ries

Of the several interesting physical properties of clay which have claimed the attention of investigators in recent years, none is more important than the behavior of the material when heated to temperatures above those of dehydration. Some of the problems to be solved are: 1. The mineralogical changes that take place in firing. 2. The relation between temperature and change in constitution, shrinkage, porosity, etc. 3. The importance of the time factor, as duration of firing, either in reaching a given temperature, or of exposure to a constant temperature. Mineralogical Changes As a result of fusion, reactions take place between the constituents of a clay, which result in a reorganization of the mass, and the formation of new compounds. Of the new minerals developed, sillimanite is the one usually recorded, and has been referred to by a number of observers.' There appears to be a difference of opinion, however, regarding the temperature at which it is formed. Thus Klein2 notes that sillimanite forms only above 1300" C., while Mellor claims that it can develop below 1200" C., the difference in results being conditioned by the time factor. In Klein's experiments the test pieces were fired in 12 hr., while in Mel-lor's, the temperature rose from 800" to 1180" in 24 hr., and occupied the same time in cooling back to 800".

Jan 1, 1918

By G. E. Mellor, R. E. Lippoth, T. B. Faddies

The Trixie mine is located in the East Tintic Mining District. Since production began in 1970 over 450 000 tonnes of ore grading 239 grams of silver, 6.9 grams of gold, and 1.2% Cu have been mined from veins in Cambrian Tintic Quartzite. Detailed geologic mapping and extensive sampling are essential for compiling the data base required for efficiently developing and mining known reserves as well as planning exploration and development work. Although the basic techniques used by the geology group at the Trixie were developed many years ago, the reduced activity in underground precious metal mining in the U.S. have made these techniques less familiar to many presently active geologists. The increased activity in precious metals search and exploration again offer cause for the application of these techniques as a prerequisite to efficient exploration, development and production.

Jan 1, 1984

By Paul M. Musgrove, Larry S. Diaz

Recent tests conducted at Inspiration Consolidated Copper Co. examined some aspects of the value of a continuous measurement of particle size to the operation and control of a mill grinding circuit. Inspiration's control objectives and kinds of control systems developed in recent years to attain these objectives are outlined. A description is given of the arrangement of the test circuit at Inspiration and also of the systems used to measure particle size of the cyclone overflow product in these tests. Use of on-line size measurement for the analysis and improvement of grinding circuit performance is illustrated by relating how two important relationships were detected. Finally, the performance of a particle-size-based control system is described, including preliminary conclusions as to increased productivity.

Jan 1, 1974

By W. J. Reagan

MANY factors enter into the manufacture of basic open-hearth steel of high quality. Perhaps the two most important are temperature and the iron oxide content of the metal. If we can control these two factors we can essentially control basic open-hearth practice. SOURCE AND EFFECT OF IRON OXIDE Earlier investigators, especially Herty and his associates, have shown that iron oxide is introduced into the open-hearth furnace in four ways:1 1. - By oxidation of the scrap by furnace gases. 2. By decomposition of the limestone. 3. By oxidation of the iron oxide in the slag by furnace gases. 4. By direct addition of iron ore to the charge. We also know that the speed of operation of an open-hearth furnace depends, for a given charge and given combustion conditions, on the rate at which iron oxide will diffuse from the slag into the metal. The rate of diffusion depends upon a number of variables, such as iron oxide content of the slag, slag viscosity, etc., which also depend upon the amount of iron oxide in the metal, amount of carbon present, temperature, and so forth. For a given carbon and a given temperature, the iron oxide content of the metal is in proportion to the iron oxide content of the slag. This fact can be easily verified by analysis of slag samples taken as described by Herty.2 It is preferable to take these samples just before deoxidation. In killing the steel samples with aluminum it is desirable to use aluminum rod of 99 per cent purity; ordinary commercial aluminum rod with a purity of approximately 92 per cent is not satisfactory. In drilling these samples it is also essential to take the largest amount of drillings possible. This gives more accurate results because it eliminates spotty segregation of Al203.

Jan 1, 1932

By C. L. Dake

Residual deposits occur both as products of weathering and as products of hydrothermal decay. Products of Weathering That climatic conditions affect greatly both the rate and the results of weathering, is shown in temperate, polar, arid, and tropical regions, each of which will be considered separately. Weathering under Temperate Climates The decomposition of any rock is accomplished by the removal of the more soluble bases, and a concentration of the relatively insoluble oxides of iron, aluminum, and silicon. By reason of its somewhat greater solubility, silica is much more subject to removal than iron and alumina. The two important residual end products of weathering are sands and clays, the former consisting essentially of quartz, and the latter of kaolin and limonite.l When such deposits are formed in situ, the sands and clays are not separated, but remain as mixtures, which can be more or less perfectly separated by treatment with water. In such a separation, the ferric oxide or hydrate tends, by reason of its fine state of division, to remain with the clays and silts rather than the sands. While ferruginous sandstones are everywhere common, they are rarely rich enough in iron to become an ore without secondary concentration. Since the silica of these sandstones is completely crystalline quartz, it is much less liable to removal by solution than are the more soluble forms of partly amorphous chert and jasper, which have been removed on so large a scale from the Lake Superior iron formations.2 Moreover, the iron cement of sandstones, which constitutes the chief iron content of these rocks, is often a result of later infiltration, and not of original sedimentation. Thus if clays rather than sands contain the iron of residual decay,

Jan 1, 1916

By J. H. Nead

The subject of this paper is one to which there are many references in the literature on the manufacture of steel in the open-hearth furnace, but few actual experimental data have been published. For that reason, the presentation of results obtained from two open-hearth heats where attempts were made to measure the sulfur absorption will be of considerable interest and value. The two heats on which the experiments were made were Armco ingot-iron heats and differ from the usual open-hearth heat of medium- or mild-carbon steel in that the refining is carried further; in this product the carbon and manganese are reduced practically to traces. In most other respects, and especially in respect to the absorption of sulfur from the producer gas, the two heats are typical of usual open-hearth practice. The object of the experiments made on the first Armco iron heat was to determine the fluctuation of the composition of the metal bath and the slag throughout the course of the heat, with especial reference to the variations in sulfur. It was hoped to determine whether there was an increase in sulfur in the bath from the producer gas and if so at what stage in the process the increase occurred. The experimental method consisted of charging analyzed scrap and pig iron, so that the sulfur in the charge could be calculated. Then, throughout the duration of the heat, metal and slag samples were takcn every half hour, beginning as soon as there was enough molten metal to take a sample. These samples were analyzed; the results are given in Table 1. All domestic scrap was used and the charge was made up as follows: Head End Finish Pounds Pound Pig iron........................ 36,300 Pig iron....................... 23,900 Sheet scrap bundles............. 36,200 Sheet bars..................... 23,900 Sheet bm..................... 40;200 The total charge, exclusive of the re-pig added near the end of the heat, was 160,500 Ib. The limestone charged was 21,400 Ib., or 13½ per cent.

Jan 1, 1924

By R. B. Sosman

INTRODUCTION WE have shown in the preceding paper that practically all natural oxides of iron contain a determinable percentage of ferrous iron, and in many cases the percentage approaches that in magnetite itself. Some of these oxides are true homogeneous solid solutions. Others are not homogeneous, and can be separated magnetically into fractions. The nature and cause of this inhomogeneity in certain special cases form the subject of the present paper. MAGNETIC FRACTIONATION OF OXIDES OF IRON The magnetic fractionation of a sample of oxide can be conveniently carried out by powdering the material very fine, and exposing it at various distances from the poles of an electromagnet. The magnet that we used was specially designed 1 to give a strong field together with a steep gradient outside of the poles. It is set in a frame, with the pole pieces directed downward. A glass plate can be adjusted at various distances beneath the poles. If the fine iron oxide powder is placed just beneath the glass plate, successive portions of the powder are picked up by the magnetic attraction and are caught against the glass plate, the most magnetic portions being taken up at the greatest distance from the poles. Some natural oxides can thus be separated into several-fractious of different magnetic susceptibilities. Among other natural iron oxides, we examined the powder obtained by crushing some crystals of hematite from Elba.2 We found that

Jan 6, 1917

By J. D. Forrester

SINCE the introduction of the first percussion rock drill in about 1850, drilling equipment has undergone a progressive evolution so that a wide range of special classes of machines now are marketed by several manufacturers. Essentially all of the drilling machines presently employed for blasthole drilling are of the hammer-drill type. They are classified as hand-held hammers (jackhammers, sinkers, etc.), drifters (light or heavy), and stopers and are of many sizes; varying in weight and rotative and blowing power. Most makes of drill machines fundamentally are the same in principle of operation as they are designed to strike a blow on the end of a drill rod in the manner of early-day hand drilling. However, beyond this common characteristic, the similarity among different makes ceases. In choosing between similar machines of one make or another, it is important to remember that rock drill manufacturers have not attempted to standardize drill parts, the result being that a mine operator must approach, because of replacement parts, standardization by limiting the makes of machines used. The present-day selection of any particular drilling machine is dependent fundamentally on its inherent ability to make a hole, or series of holes, as speedily and as cheaply as is possible. Two categories of controlling elements become apparent in any analysis devoted to making the choice of a drill, namely: 1-Conditions under which the equipment is to be used, such as mining method practiced, type of labor available, character of rock material. 2-Physical characteristics or features of the given drilling machine. Regardless of the controls of class 1, above, the elements of this category are fixed by several factors. All of them are interrelated and, though some often are more important in one case than in another, an unfavorable variation of any-others being essentially equal-is sufficient to discredit the optimum applicability of the particular drill machine. The relative factors in the selection of a machine are as follows: First cost-This is not generally an important item on a comparative basis as the marketing of drill machines is highly competitive and most makes are priced closely.

Jan 1, 1952

By Neil Johnson

IN the cyanidation of gold, silver and mixed ores, the solids suspended in the pulp after fine grinding, primary settling and series agitation are subjected to a washing step known, generally, as countercurrent decanta-tion, abbreviated C.C.D. The conventional C.C.D. plant consists of a series of separate thickeners-three to five in number-arranged in series on slightly different elevations. Solids settled in the first thickener are pumped at maximum density into the second thickener, where they are diluted with weak solution overflowing the third. After settling in the second thickener they are pumped to the third, where the process of repulping with still weaker solution is repeated, and so on throughout the system, until they reach the last thickener and are repulped with barren solution or water. Recently there has been developed a new type of thickener, known as the Dorr Washing Tray Thickener, consisting of up to five individual thickeners, which performs in a single unit all the functions of a conven-tional C.C.D. plant. Fig. 1 illustrates the essential features. It is a multicompartment tray thickener, in which the trays operate in series instead of in parallel for countercurrent washing. Feed enters the top compartment via a central, semisubmerged feed well. Strong solution overflows into a peripheral launder. Solids settle to the bottom, are raked to the center and flow into the top of the second compartment, directly below, via an inverted cup and seal. Solids pass downward, compartment by compartment, against a counter flow of wash solution and finally of fresh water. Thus, in accord-ance with the basic C.C.D. principle, the solids transfer the dissolved metal content to the wash solution and finally are removed by a dia-phragm pump from the bottom compartment virtually free of valuable material. Similarly, the wash water, as it flows through the system, becomes increasingly enriched in dissolved metal until it overflows from compartment two and returns to the process.

Jan 1, 1939

By S. Fukushima, E. Kimura

In the Mitsubishi beneficiation process of ilmenite, chlorine is regenerated in the dechlorination furnace where the gases produced from a selective chlorination of ilmenite are directly introduced. The present paper describes a reaction mechanism and mixing characteristics of the reactant gases for dechlorination of ferric chloride with oxygen. A furnace of a small diameter where the reactant gases passed through in the state of nearly plug flow was used for determination of the effects of temperature and of partial pressures of ferric chloride and oxygen on the rate of the reaction. The experimental data of the reaction rate were applied to various models for calculations of the rate equations and the most suitable reaction model was determined. The results of the experiments also showed that effects of gas mixing onto the reaction rate could not be ignored, so that experiments of gas mixing was carried out. Gas flow patterns and scale effects were observed with use of transparent model furnaces of different sizes.

Jan 1, 1976

I SHALL proceed in this chapter to tell you about lead. Because this metal is overabundant in wateriness, and also because it has its other substances in poor elemental mixture, it is highly impure. It is called an imperfect, leprous, and little-fixed metal, which it clearly shows itself to be because of the ease of liquefying it and because it is easily converted largely into a dross that is almost earthy and also because of the stain that it leaves when it rubs against anything. Nevertheless, when we consider its effects, we judge it to be a metal that we are greatly indebted to. Even though Nature in creating us has put into our souls such a thirst and desire

Jan 1, 1942

By J. H. Brophy, A. I. Prill

The authors have previously investigated the solid-state activated sintering of tungsten powder with various Ni-Cu additions.' Log shrinkage vs log time plots showed changes in slope from 4 to x at intermediate times during the sintering process. This was attributed to a change in the rate-controlling mass-transport process from solution of tungsten into the tungsten-alloy interface to diffusion of tungsten in this interface. It was postulated that the melting of the activating layer should not affect this transport process. However, the superposition of rearrangement due to the presence of a liquid phase complicates the data analysis. It is the purpose of this note to apply the analysis of Prill, Hayden, and rohy' to account for "rearrangement shrinkage'? in liquid-phase sintering of the W-Ni-Cu system. This results in "solution-precipitation stage" shrinkage plots which were comparable to those obtained in solid-phase activated sintering of the same system. If one assumes total shrinkage to be the sum of rearrangement and solution precipitation, the effects can be isolated easily.2 This results in the general equation:

Jan 1, 1967

By Haydn H. Murray

Although alumina constitutes about 15% of the earth's crust, it is expensive to separate and purify for the production of aluminum with the exception of the alumina in bauxite. The United States has a variety of nonbazurite resources that could substitute for bauxite, including high alumina clays, alunite, dawsonite in oil shale, anorthosite, and nepheline venite. Each of these resources is discussed from the standpoint of geology, geography, processing, and potential recovery. Potential byproducts include alica from clays, potash and sulfuric acid from alunite, soda ash from dawsonite, and soda ash and potash from anorthosite and nepheline syenite.

Jan 1, 1983

By Thomas B. Dellinger

Since 1950, rotary-drilled, large-diameter holes, "big holes", with depths to over 300 ft and diameters of over 30 in., have become numerous and widespread. 50 such holes have been drilled for access shafts to LPG mined caverns. Over 70 holes have been drilled for various other commercial activities. Over 150 holes have been drilled by the AEC for atomic testing purposes. These holes have ranged up to 300-in. diam with 1600-ft depths, 120- in. diam with 570-ft depths, and 72-in. diam with 4800-ft depths. Equipment is now available to drill a wide range of big holes for varied requirements. At least a dozen drilling contractors are participating or have participated in the drilling of big holes. The accompanying tables show pertinent historical, technical and economic data on over 250 holes. The purpose of this paper is to present a review of the big hole drilling equipment available, a compilation of the available data on large-diameter holes, to show the experience obtained to date and to show that big hole drilling is feasible and available to the industry.

Jan 12, 1965

Draftsman and transitman for coal mine work in Middle West. Salary $125 per month. No. 277. Men capable of taking charge and superintending the construction of plants. No. 331. Position for mining engineer in district with two large operating mines, four mines under development, and two mines temporarily closed, because of water conditions. Another assistant is desired. Excellent school facilities in model town; house available for engineer. Would consider recent graduates. No. 332. Engineer or firm of engineers competent to survey and estimate the extent and the contents of a deposit of clay in the southern -mountains of Pennsylvania, and to figure on the cost of getting the material, presumably through a tunnel running into the side of the hill on which the property is located, as this is the method by which similar properties in the vicinity are being worked. Prefer to have some one who would bid on the actual work of opening up the deposit. No. 333. Four assistant division foremen. These men must be Americans who can talk Spanish, and must be good miners and familiar with handling large stopes by the cut-and-fill, square-set and top-slice methods. Salary $200 gold per month. No. 334.

Jan 8, 1918

By New kensington P. A, W. L. Fink, H. R. Freche

The investigation of aluminum alloy systems prior to 1923 was severely handicapped by the low purity of the best aluminum available. However, by that time, the electrolytic purification of aluminum had been developed by the Aluminum Company of America,(1)† and in May, 1923, there was initiated, under the direction of E. H. Dix, Jr.,(2) a program for the investigation of the aluminum-alloy systems using the purest electrolytically refined aluminum. Up to the present time 15 papers (3) have been published, most of which are on the binary aluminum systems. Work is now in progress on the ternary systems, and it seems probable that most of the future work will be on ternary systems. Therefore this survey of the binary aluminum systems investigatcd up to the present time (the sixteenth paper of the series) concludes the first phase of this program. Certain qualitative relations between corresponding portions of the various binary diagrams as well as between different parts of the same diagram were noted some time ago by R. S. Archer.(4) In the present paper these relations and others are considered quantitatively by the application of well-known thermodynamic equations or by newly discovered empirical relations. No attempt will be made here to present the history of the development of the thermodynamic equations defining equilibrium or their application to metallic systems, although a list of references is given at the end of this paper for those who are interested in this phase of the subject. Two thermodynamic equations, which will be employed extensively in this paper, are: loge x1 = - L/RT + C

Jan 1, 1934

By J. M. Lohr

THE characteristics and uses of thermocouples of platinum and the platinum alloys being so well known, this paper will be confined to base-metal couples. During the past decade, there has developed a strong demand for thermocouples made of metals cheaper than the platinum alloys, and suitable for industrial heat measurements. Much research has been clone but only a very limited number of alloys have been found to possess the necessary characteristics for general technical use. In the development of thermocouple alloys it is necessary to consider the following points: The electromotive force and temperature relations; permanency or constancy; reproducibility; manufacturing difficulties; durability; and accuracy in use. The electromotive force developed by the thermocouple should increase with the rise of temperature according to some definite law. It is desirable that the electromotive force should vary directly with the temperature difference of its junctions, in other words, giving a curve linear or nearly so. It is also desirable that the resulting electromotive force be as large as possible for any given range of temperature, thereby insuring greater accuracy of readings.

Jan 9, 1919

By Pete Turcic, Wade E. Cooper

Many factors influence radon-222 influx and radon-daughter concentrations in underground uranium mines. A brief review of some of these factors is presented. Current radon-222 and radon-daughter control principles and practices for U.S. underground uranium mine atmospheres are discussed and a brief review of the applicability of other possible control methods such as rock sealants, radon-222 removal, and radon-daughter removal is given.

Jan 1, 1982