Search Documents

By M. I. Jacobson, M. L. Hammond

The solid solubilities of high-purity silver, aluminum, chromium, copper, and iron in zone-refined beryllium have been determined. Diffusion couple sandwiches of beryllium with aluminum, copper, and silver foil and diffusion couples of beryllium with two-phase alloys in the Be-Cr. Be-Fe, and Be-Ag systems were analyzed by electron beam micro-probe techniques. This paper describes the material used, the experimental methods for preparing the diffusion couples and the alloys, the analytical techniques, and the results obtained. The results are compared with those of previous investigators who used materials of lower purity. ~NVESTIGATORS of beryllium phase diagrams have often been hampered in their interpretations of certain phase boundaries because of the relatively low purity of the beryllium used. This has sometimes resulted in the appearance of three phases in the regions where only two should exist. Advances in purification methods, specifically zone refining, have made available beryllium that is considerably purer than the material previously used for phase diagram studies. The primary object of this investigation was to reex-amine portions of the beryllium-rich end of the binary systems of beryllium with silver, aluminum, chromium, copper, and iron to determine more accurately the limits of terminal solid solubility. The five elements—silver, aluminum, chromium, copper, and iron—include some which are commonly found as the major impurities in beryllium, some of which are being used as solid-solution alloying elements, and some of which are used in ductile matrix alloys. They are thus of considerable importance to physical metallurgists who must work with beryllium but who must rely on the present inaccurate or incomplete diagrams. The determination of more reliable diagrams would aid researchers concerned with the problems of alloying, heat treatment, and ductility. MATERIAL The beryllium was acquired from the Franklin Institute in the form of a single-crystal, 6 in. long by 1 in. in diam, zone-refined in three passes from Pechiney SR-grade beryllium bar. The principal impurities, as determined by mass spectrography at Battelle Memorial Institute, are shown in Table I. Vacuum-melted copper, silver, and aluminum, and electron-beam zone-refined iron were obtained from the Materials Research Corp. in the form of 1/2-in.- diam bars. Iodide chromium was obtained as flakes from the Chromalloy Corp. Analyses supplied with these metals are shown in Table 11. EXPERIMENTAL PROCEDURE Preparation of Diffusion Couples. Two types of dif-fusion couples were used in this study. For the copper, silver, and aluminum systems, the couples were sand-

Jan 1, 1969

By Francis M. Walters

THE problem of making iron-manganese alloys of scientific purity is a rather difficult one. They cannot be prepared in air because of the readiness with which the metals oxidize at the temperature of melting; and they cannot be prepared in vacuum because of the, high vapor pressure-of- manganese. The very property of: manganese which permits it to be purified interferes with the utilization of the best method of making pure alloys. Accordingly, it is necessary to use a gas atmosphere which will not affect the-properties of the alloys. The gases available for the purposes are hydrogen; helium and argon. Nitrogen forms intermetallic compounds with manganese very readily. Hydrogen, while valuable as a deoxidizer and having the advantage of being comparatively cheap, is explosive over a wide range and, has a rather high thermal conductivity. Helium is reported as, costing little but is difficult to secure at a reasonable price and also has a conductivity nearly as high as hydrogen. Since argon has a sufficiently low thermal conductivity, it has been selected for use in one induction furnace for melting, under a controlled, gas atmosphere, in spite of its cost, which is so high (70 cents to $1.50 per cubic foot) that it must be stored and purified.. Such a gas atmosphere-as argon makes necessary the use of the, high-frequency induction method of heating. This involves, a non-metallic container for the gas; .which is most conveniently of fused quartz or glass. The next

Jan 1, 1929

Jan 1, 1947

By J. M. Snook, F. C. Langenberg

FOR a better understanding of the melting and refining processes, the oxygen content of the steel bath should be determined. The oxygen content influences many process and product variables such as the efficiency of alloy recoveries, the ingot structure (through reaction with carbon in the steel), certain reaction rates, cleanliness (formation of indigenous oxide inclusions), and mechanical properties. Many methods of sampling liquid steel for oxygen have been devised. These methods can be divided into two main groups: 1) taking samples directly in the furnace or ladle;'-'0 2) removing the metal from the furnace or ladle in a sampling spoon and pouring it into a mold, or drawing the metal from the spoon into a sample holder.11-l4 The advantages and disadvantages of the two general sampling methods are presented in Table I. The bomb-sampling technique described by Huff, Bailey, and Richards8 has been used by the Crucible Steel Co. in certain research projects where oxygen contents were needed. It was recognized that a localized boiling condition could result when the mold is introduced into the steel bath, although the work of Gilbert and Bailey9 seems to indicate that the carbon boil occurring in the bomb-sampler cavity has a negligible effect on the oxygen content. In order to confirm the reported negligible effect of a carbon boil, additional work was done with adaptations of the conventional bomb sampler. The methods used are shown in Fig. 1 and are as follows: 1) Type A: aluminum wire (0.125-in. diam) coil in cavity; steel cap over mouth 2) Type B: aluminum cup in cavity; aluminum cap over mouth, 3) Type C: aluminum cup in cavity; steel cap over mouth, 4) Type D: fine aluminum wire (0.013-in. diam) in cavity; steel cap over mouth. The amount of aluminum wire in the Type A and D samples varied from 0.8 to 1.2 pct of the sample weight. The aluminum cups averaged 2.0 pct of the sample weight; the latter were used to ensure that the steel contacting the walls of the bomb cavity was fully killed. Samples were taken from plain carbon heats made in open-hearth furnaces. This grade of steel before silicon additions is essentially an Fe-C alloy and the effects of other alloying elements on the oxygen activity can be neglected. The results of sampling with the bomb samplers is shown in Fig. 2 where the percent oxygen is plotted against the percent carbon on log-log paper. Spoon sample results on the same grade of steel where the sample was killed in the spoon are shown in Fig. 3. The oxygen contents were determined by the vacuum fusion method. A comparison of Figs. 2 and 3 shows that the oxygen concentrations obtained with the spoon-sampling method (metal killed in the spoon after slag removed

Jan 1, 1960

By D. J. Sellmyer

In order to orient single crystals by the back-reflection method it is necessary to know the angles between the various crystallographic planes. These angles have already been published for the hexagonal close-packed metals magnesium, zinc, and cadmium.'

Jan 1, 1965

By Robert Warner

The growing importance of screening makes an accurate measure of the quality of a sizing operation desirable. Screen efficiency is considered equal to the percentage of true undersize in the feed obtained as undersize from the screen. This method is unreliable, as it gives the same credit for removing minus 200-mesh material as for removing material just able to pass the aperature of the screen. A more accurate measure of screen efficiency is to consider only the work done on the "difficult" grains, that is, those grains of which the intermediate diameters closely approach the screen aperture.. The application of this method is given, together with the derivation of formulas and an example of their use. Is AN accurate measurement of the efficiency of a screen under a given set of operating conditions valuable? If so, what is the efficiency; of, a screen and how can it be measured? Sizing, especially of the finer sizes of material, has increased in importance in the development of flow sheets as a result of the perfecting of the rapid vibrating screens. More consideration should be given screens in the preparation of ball-mill feed, where they permit the admission of a dryer feed than, the classifier. Where possible, the introduction of a screen ahead of the primary ball-mill, and the diverting of ore below, say, 4 mm. to a secondary mill, might result in a greater overall economy because of the thicker feed and the better, adjustment of crushing media and mill operation to the reduction demanded. With the present trend back toward a combination of gravity methods and flotation, rather than flotation alone, the accurate, economical sizing possible with the new screens makes fine jigging a method to be considered. W. 0. Borcherdt1 and John Bland2 discuss the screening problem and also the value of close sizing in the concentration of some of the rare-metal ores. If a screen is to be used, it should be selected in competition with others; other things being equal, that screen which makes the cleanest oversize should be preferred. The quality of the screening and the tons

Jan 1, 1924

By F. P. Agterberg

It can be useful to model the mean grade values for a metal in mineral deposits containing that metal as representing the extreme value tail of a lognormal frequency distribution for the concentration values of the metal in common rocks of all types. Results for copper and zinc in the Abitibi area of the Canadian Shield are compared to results previously obtained for the Canadian Appalachian region. The lognormal model is also applied to a set of 162 large gold deposits in the Abitibi area. In the second part of the paper, 1311 large and small gold deposits in the Abitibi area are modeled as discrete events. By means of a newly developed spatial clustering model it is possible to predict the variances of random variables for frequencies of deposits in cells of different sizes.

Jan 1, 1981

By Alexander L. Holley

(WITH FIGURES ON PLATE I.) A CHARACTERSSTIC, and, to Americans, an amusing discussion of the three-high rail-mill, arose out of the reading of Mr. Lauth's paper on three-high plate-mills, at the Glasgow meeting of the Iron and Steel Institute. From the report of the meeting in the English papers, it appears that Mr. Menelaus, the celebrated rail-maker of Dowlais, could not wait for the discussion of Lauth's plate-mill, but launched at once into the British objections to the three-high rail-mill, which is quite another matter. The American mill, which is very different in principle and ar-

Jan 1, 1873

By J. Pinto, F. Galasso

THE current emphasis in preparing boron fibers by reduction of gaseous boron compounds on a resistively heated metal wire substrate has renewed interest in the borides of those metals which have relatively high melting points and are available as fine wires. A knowledge of the structures and properties of the borides, which are formed when boron diffuses into the metal core during boron deposition, can be of assistance in the understanding of the boron fiber formation process and the fiber properties. Many of these borides are well-known and their properties have been measured. However, when an unidentified boride is found in the core, it may be difficult to establish its composition because of the small amount of material available, the preferred orientation effects on the reflections in its X-ray pattern, and the possible overlap of X-ray reflections if several borides are present in the core. For example. the proper indexing of the X-ray pattern of WB4, which was formed in the tungsten substrate core during boron fiber formation, was accomplished only after small single crystals of this boride were grown and X-ray precession investigations were conducted.' This note presents the results of a study of the phases formed in the core when tungsten, tantalum, and molybdenum metal wires were used as substrates in the boron fiber preparation process with particular emphasis on the identification and characterization of a higher boride of molybdenum analogous to WB,. Boron was deposited on resistively heated stationary 0.0012-in.-diam tantalum, tungsten, and molybdenum wires at 1050°C for various times up to 60 sec using boron trichloride and hydrogen as the reactant gases. After 60 sec of boron deposition the fibers were approximately 0.006 in. in diam. Examination of photomicrographs of fiber cross sections showed that the boron had diffused nearly to the center of the tungsten and molybdenum cores in 15 and 30 sec, respectively, and only halfway to the center of the tantalum core in 60 sec. X-ray diffraction photographs of the fibers indicated that it was also after 15 and 30 sec deposition times that the tungsten and molybdenum metal reflections, respectively, had disappeared from the X-ray patterns of the fibers. The patterns of the boron fibers produced using tantalum wire as a substrate showed that amorphous boron, TaB2, and tantalum metal were present after a few seconds deposition time and remained even after deposition times of 60 sec. Until a deposition time of 15 sec was reached, the tungsten substrate fibers contained amorphous boron,273 6WB, W2B5, and WB4 as well as tungsten metal, while the molybdenum substrate fibers contained amorphous boron, MoBa, Mo2B5, and molybdenum metal for deposition times up to 30 sec. Just before the molybdenum metal pattern disappeared, a pattern similar to that of WB, appeared, suggesting that a phase, MOB,, isomorphous with WB,, was present in the fiber. This same pattern was obtained from the product formed by heating a mixture of molybdenum metal and excess boron powder in a boron nitride crucible at 1960°C in an argon atmosphere. As was the case with the WBn pattern, this pattern could best be indexed on the basis of a hexagonal unit cell rather than the tetragonal unit cell Chrktien and Helgorsky reported for ~0~4,~ see Table I. The unit cell parameters for MoB4 were calculated to be a, = 5.214A, co = 6.358A. Assuming the space group P63/mmc and positions5 2M01 in 2b and 2MoII in 2c found for tungsten in WB~,' a logical structure for MOB, was determined using geometrical considerations to place the boron

Jan 1, 1969

By A. E. Martin, Gerhard Derge

IF the molecular constitution of molten slags were better known, the nature of chemical reactions in slags and between slags and metals could be better understood and as a consequence might be better controlled. Constitutional information can be obtained by studies on either the molten or the solidified slags. Valuable as the studies on solidified slags admittedly are for many purposes, especially as control methods in steelmaking, they are always of questionable value in giving information on the molecular constitution of liquid slags. However, the characteristics of molten slags such as viscosity, rates of diffusion, and electrical conductivity can be determined experimentally and interpreted along with other knowledge on slag-metal and slag-gas reactions so as to provide direct information on liquid slags. Metallurgists are accustomed to regard reactions in molten slags as involving only neutral molecules, whereas it is quite possible that ionic constituents are actually involved. For example, the dissociation of calcium silicate usually is represented as Ca2SiO4 = 2CaO + SiO2 although a reasonable alternative would be to write Ca2SiO4 = 2Ca+2 + Si04-4 Such ionic dissociation has been suggested frequently without adequate experimental proof. This paper deals especially with electrical conductivity measurements on slags of the blast-furnace type. These measurements were made to determine whether or not slags are ionized and, if so, to provide a qualitative estimate of the extent of ionization. Electrolysis experiments that indicate the identity of the ions present are also reported. Since the presence of ions has not been considered carefully in modern slag studies, the relevant literature will be reviewed. REVIEW of LITERATURE In 1906 Aiken1 obtained a patent for a continuous process of producing iron electrolytically by passing a direct current through a bath of FeO-SiO2 to which iron oxide was added periodically to maintain a uniform concentration. The patent also included the addition of CaO and MgO to the bath to lower its melting point. The silicate melts involved were thus in the same system as basic open-hearth slags but with higher FeO and lower CaO contents. Electrical conductivity measurements were made on some molten silicates by Doelter2 in 1907. Natural silicates, such as

Jan 1, 1943

By D. T. Van Zandt

IN the late 1920's rotary drills began to replace the churn drills in the petroleum industry, but until the middle 1940's the churn drill was the only widely accepted means of drilling large-diameter blastholes for quarry operations. The Calcite plant of the Michigan Limestone Div., U. S. Steel Corp., was one of the first to experiment with rotary drills for quarry blasthole drilling, and the first to employ compressed air on a fully rotary rig to cool the bit and raise the cuttings to the collar of the blasthole. The Calcite plant operates a limestone quarry near Rogers City, Mich., in the northern part of the lower Michigan peninsula. The formation quarried, a portion of the middle Devonian series, is the Dundee limestone, which is uniform, seldom massive, and characterized by definite bedding planes. The dip is southeast, 40 ft to the mile. Quarry faces vary from 20 to 116 ft in height. Vertical blastholes are used entirely, from three to five rows of holes being drilled parallel to the working face, spaced 18 ft apart with 18-ft burden and drilled 6 to 8 ft below shovel grade. Quarry operations coincide with the navigation season on the Great Lakes, as the bulk of the stone is transported by lake carrier. The normal operating season runs from April to December, the remaining time being devoted to stripping operations and plant and equipment maintenance. In the followirig discussion drilling rates mentioned refer to overall drilling time and include all operations such as moving from hole to hole, penetration and extraction of tools, and routine maintenance. Time consumed by such factors as power delays and major machine repair is not included in drilling time unless otherwise stated. Figures cover only operations at this one plant in the formation mentioned. Needless to say, a very different set of figures could be obtained in a different formation. However, the comparison of footage obtained with churn drills and rotary rigs in this particular formation has been used as an indication of what might be the expected performance of rotary rigs in other formations. Prior to 1950 the bulk of the blasthole drilling at the Calcite plant was done by electrically powered churn drills. Both crawler and wheel-mounted rigs were used. These machines, which mounted a 22-ft drill stem of 4½ in. diam and a spudding type of bit 2 to 4 ft long, drilled a hole of 5 ?-in. diam. Average drilling rate of these rigs in the Rogers City formation was 8 % ft per hr. In 1946 one of the first rotary blasthole drills offered to the quarry industry was put into use on an experimental basis. This machine, known as the Sullivan Model 56 blasthole drill, Fig. 1, was on 16-in. crawler pads and electrically powered at 440 v. The drill bit, a Hughes Tri-Cone roller bit of 5?-in. diam, Type OSC, was threaded into the end of the 4-in. square hollow drill rod or stem. These drill rods were 20 ft long with female threads on one end and male on the other to allow for addition of the desired number of rods for drilling holes of various depth. Rods were handled by a single drum hoist geared to the main drive motor and racked by a 30-ft derrick or mast when not in use. The cable from the hoist drum fed through a crown block on the top of the derrick back to the water swivel mounted in the top end of the drill stem in use. This cable remained attached during drilling operations and was used to hoist the tool string from the hole. Down pressure was applied to the tool string by means of a pair of 4-in. diam hydraulic cylinders acting on the drill chuck holding the drill rod. The first chuck consisted of flat jaws which gripped the flat sides of the stem. These jaws were controlled by set screws forcing them into contact with the drill stem. As these set screws had to be loosened and tightened by hand with each stroke of the hydraulic feed cylinders, there was great delay. For this reason the semi-automatic chuck was developed which automatically gripped the stem on the downward stroke but released for retraction of the hydraulic feed cylinders. Rotation was imparted to the tool string by a rotary table acting on the chuck and geared to the main drive motor through a separate gear train and clutch. A positive displacement water pump, mounted on the drill, fed water through a system of pipes and hose into the water swivel mounted on the top of the drill rod and through the rod and bit, washing the drill cuttings to the collar of the hole. Where water was scarce, provision was made to settle out the cuttings coming from the collar of the hole and re-use the water. Where water was abundant the stream coming from the hole was wasted. Drilling rate with this machine was about 20 ft per hr and bit life 1600 ft of hole. While this rate was more than twice that obtained with the churn drills employed, the problem of water supply and drill cuttings disposal rendered the machine impractical from an operating standpoint. Consequently it was used only in that part of the operation for which water was easily supplied, when the character of the formation made it least difficult to wash cuttings away from the collar of the hole. In October 1949 it was suggested that drill cuttings be removed by compressed air, long used for this purpose on pneumatic drills, and collected at the collar by suction. Thereafter, the water pump on the Sullivan 56 was replaced by a 500-cfm air compressor and a trial run made. Air pressure at

Jan 1, 1955

By J. E. Crawshaw, Francis B. Foley

In the first report1 disks of steel of known composition and history were exposed, under carefully prescribed conditions, to impacts of explosion products resulting from the explosion of 50-gm. charges of explosives having well-determined rates of detonation, or to impacts of a weight of known mass, falling through measured distances. There were available at the Bureau of Mines Experiment Station five explosives, having rates of detonation of 5716, 4470, 3190, 2296, and 1523 meters per second. It being desired to continue this exposure downward, and no explosives with a lesser rate of detonation being at hand, resort was had to the impact of a falling weight, the differences in the velocity of impact being attained by varying the height from which the weight was allowed to fall. It was expected by this means to demonstrate experimentally that the development of Neumann bands was determined by the suddenness of the deformation of the metal in which they were produced. But while progressive deformations were obtained with the explosive charges, the falling-weight method failed because the tup was progressively deformed, also the disks were so flattened as to be unfit for metallographic examination. A return, therefore, has been made to the use of explosives as the source of energy, an air-gap being interposed between the charge of explosive and the disk, as the effect diminishes as the function of the distance between the charge and the object on which the products of its explosion, or the shock wave from its detonation, impinge. The details of the arrangement of the tests by the air-gap method were the same as those described by Foley and Howell,2 except that after the system had been set up and the desired apparent specific gravity for the explosive attained by tamping it, the small lead block, with the steel disk adhering

Jan 1, 1926

By Frank S. Gardner, Morris Cohen, Dara P. Anita

There is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a suecimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallo-graphic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X - ray exposure and film - development conditions, a standard reference line is Superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By Morris Cohen, Dara P. Anita, Frank S. Gardner

There is a conspicuous lack of information in the literature on the precise role played by residual quantities of austenite in heat-treated steels. While retained austenite may be expected to have significant effects on such important properties as the impact resistance of tools and carburized parts and the dimensional stability of dies and gauges, attempts to study these problems systematically have suffered from the absence of a reliable technique for ascertaining absolute amounts of austenite. With such a technique, not only could the relation between residual austenite and service behavior be investigated, but the chemical and heat-treatment factors that control the quantity of the austenite could also be established. Thus, the retained austenite content could then be regulated in accordance with the results desired. The presence of retained austenite may be inferred by observing the changes in properties (hardness, specific volume, electrical resistance, etc.) due to its decomposition on subatmospheric cooling1 or on tempering,2 but these indirect measurements are not readily translated into percentages of austenite. Quantitative determinations have been achieved in special cases by means of dilatometric3 and magnetic4,5 measurements; but the former procedure requires that observations be conducted during the hardening and involves difficult calibrations that limit its applicability, while the magnetic procedure is very sensitive to extraneous influences and depends upon assumptions that can only be considered as approximate in an absolute sense. Furthermore, both the dilatometric and magnetic effects are volume properties, and cannot be conveniently utilized to explore variations in retained austenite from point to point in a suecimen. Some microstructures lend themselves to accurate evaluation of retained austenite contents by metallo-graphic methods,3 but such instances are not too common, and at best, the procedure is tedious. The characteristic X-ray diffraction lines of austenite permit positive identification of its presence; and in the present paper the intensities of these lines, or the corresponding densities* on photographic film, are employed to measure the amount of the retained austenite. In order to cancel the effect of uncontrollable variations in the X - ray exposure and film - development conditions, a standard reference line is Superimposed on each film by maintaining a foil of aluminum in the path of the incident X-ray beam during the entire exposure. With different samples of steel and the same foil, the ratio of the density of some one austenite line to the density of

Jan 1, 1943

By J. E. Johnson

The description of the machine which coilstitutes the subject of this paper is best iutroduced by a statement of the conditions which led to its construction, which may be briefly given as follows : The ore handled at the plant to be here described* is of the variety sornetimes called by those familiar with the brown ores of the South, " Mountain," as distinguished from the " Lime-

Jan 1, 1899

By W. A. Van Voast, J. J. McDermott, R. B. Hedges

Many coal beds that will be mined in southeastern Montana are aquifers that provide essential local water supplies. Mine cuts along aquifer outcrops create almost imperceptible piezometric changes. Monitoring near such operations at Colstrip has detected almost no water-level declines in observation wells. Mine cuts between outcrops induce rapid storage depletion and associated piezometric depressions. One such cut near Decker induced 12.50 mj/day of flow from storage and created a piezometric depression of 3 m or more as far as 1500 m from the mine. No wells have yet become nonproductive but losses of some are inevitable as operations expand. Alternative supplies are available from aquifers stratigraphically below the disturbed materials. Effluents from active mines are chemically similar to other area waters because they are mixtures of ground waters entering the mine cuts. Occasional high concentrations of nitrate do occur, however, as residuals from explosives. Spoils generally consist of confined aquifers of wasted coal and coarse rubble at their bases, overlain by finer-grained sand,

Jan 1, 1980

By Robert H. Merrill, Raymond M. Stateham

Recently, the Denver Mining Research Center of the U.S. Bureau of Mines began tests to detect hazardous or potentially hazardous conditions in or around mines with infrared measurement devices. Among the many potential uses of infrared detection techniques are the location of misfires, underground mine fires, combustion in waste dumps, underground water courses and loose rock. However, the primary emphasis has been placed upon the detection of loose rock in roofs, pillars and faces in underground mines. The rock along the edge of an underground opening is subject to two temperature environments: the temperature of the air in the opening, and the temperature of the rock surrounding the opening. Assuming that the rock on the edge of the opening is solid, the rock will reach an equilibrium temperature that depends upon the temperature and flow of the air, the thermal conductivity of the rock and its ambient temperature. Presume that a loose rock exists among this solid rock; because there is a temperature barrier, to some extent, between the loose and the solid, the loose rock will be affected more than the solid rock by the temperature of the air. Therefore, depending upon the temperature differences between the rock and the air, the loose will be warmer or cooler than the solid.

Jan 1, 1970

By H. I. Meyer, D. F. Searcy

INTRODUCTION The analysls of our previous paper' on the behavior at two immiscible fluids separated by gravity into two dlstinct saturated zones in the porous medium was shown to be theoretically valid only if one of the two fluids was immobile. The practical problems associated with flow of both phases have so far been impossible of solution by these analytic methods. We, therefore, decided to resort to a simulator study to answer the following pertinent questions: 1. If the lighter fluid is produced from a point above the fluid-fluid interface, how long will it take for the heavier fluid to come up to the point where production of both fluids is taking place? 2. After steady-state two-phase production is established, what is the relative production rate of each phase, on what physical variables does this depend, and what are the boundary conditions at the outflow face? 3. A third question was at least partially answered in the course of this investigation: that of the shape of the interface under flow conditions. These questions are of fundamental importance in the fields of hydrology and the reservoir mechanics of oil and gas production. In order to simplify equipment used and still retain a fair physical representation of these phenomena, it was decided to use a Hele-Shaw type of analogy in which the flow took place between two vertically mounted pieces of plate glass. The advantage of this system is that it eliminates any surface effects between the matrix of the porous medium (e.g. packed sand) and also allows equilibrium conditions to be established more quickly. The principle disadvantage (apart from the obvious one of being one more step removed from the prototype) is that our equipment limited us to two dimensional flow studies. In spite of these limitations answers to the questions were obtained which seem adequate for our purposes. We would like to see more work of this nature done to verify and to improve our conclusions. DESCRIPTION OF EQUIPMENT AND PROCEDURE A drawing of the equipment used in this study is shown in Fig. 1. Fluid flow takes place between the two 36 in. x 12 in. pieces of plate glass held apart at the long edges by two spacers of cellulose acetate sheet (Kodapac IV) which is available in several thicknesses. This sandwich was clamped together by small c-clamps whose stress was distributed by long pieces of 3/8-in. keystock. Accurate spacing was obtained by tightening these clamps as indicated by micrometer measurements on the outside of the glass. At the upstream end of the plates a piece of 6-in. diameter pipe simulated an infinite reservoir, while at the downstream end a 2-in. Lucite cylinder with a small hole near the top of the flow region served to drain the fluid. Sealing was achieved by O-rings, the whole system being tightened by pressure on the Lucite tube provided by set screws (not shown in the drawing). The total head

Jan 1, 1957

By Sam N. Dewitt, Albert S. Trube

This paper presents a discussion of the pressure maintenance operations which were begun in the New Hope Field. Franklin County. Texas. in 1944. The project has required the injection of extraneous waters at depths from 7.300 to 8.000 ft with intake well-head pressures up to 4.000 psi in three different reservoirs — the Bacon. Hill. and Pittsburg. Records of oil and water production. water injection and the GOR have been kept for each reservoir and reservoir pressures were taken at regular intervals. These data indicate that the Bacon Reservoir had no apparent water encroachment up to the time of water injection. However. the Pittsburg and Hill reservoirs had some natural water influx hut not sufficient to prevent pressures from declining below the bubble point. The Bacon and Hill reservoirs responded almost immediately to water injection. while the Pittsburg which is the least permeable. has shown good pressure response only since .August, 1948. The principle objective of the project has been to increase ultimate recovery. Success of the project to date also has resulted in reduced lifting costs. Esti- mates based on the initial water breakthrough patterns indicate that the primary objective of substantial additional recovery will he accomplished, and there is a possibility that the original estimates elf oil recovery with pres-sure maintenance will he exceeded. INTRODUCTION This pressure maintenance project was one of the earliest primary pressure maintenance programs to he attempted on a multiple zone field. There are three producing reservoirs into which water is being injected for the purpose of maintaining pressure and increasing the ultimate recovery- from each. This paper is limited in scope to al1 account of the development of the project. the pressure production relationship prior to the injection of water and the effect of water injection on the producing reservoirs. Also discussed are the nature of the injection system and the indicated results on initial water break-through in the Bacon Reservoir. FIELD CONDITIONS The New Hope Field, which is located about 12 miles northeast of Winusboro, Franklin County, Texas, is an elongated symmetrical anticline containing four known oil reservoirs. The reservoirs are of the Trinity group of the Comanchean or Lower Cretaceous period and are found in Table I. The oil productive portion of each reservoir is not present in all of the producing wells because their areas and positions vary with respect to one another. Fig. 1 shows the relative position of the four reservoirs and illusIrate? how some wells could penetrate all four, while others are restricted to three. two. or perhaps one. depending on structural location. The first three reservoirs contain undersaturated oil. The deepest. the Elledge, has a primary gas cap. Although this reservoir covers a considerable area of the field. it has a very thin section and a low order of permeability. Elledge producing wells have generally been characterized by an early increase in GOR, making it necessary to recomplete them in other reservoirs. (At present. one well is completed in the Elledge. which is still producing.) Because of the difficulties en-countered in producing oil from this reservoir. and the small quantity of oil actually present. future attempts at producing it will probably be on a salvage basis during the later life of the program. For this reason, the remainder of this report will be confined to a discussion of the Bacon, Hill and pius-burg reservoirs.

Jan 1, 1950

By Robert Davis Longyear

In diamond-drill work, a true sample consists of all the material cut by the bit—both core and cuttings. As the recovery of this sample is the object of diamond drilling, the utmost care should be taken to secure it. Speed of drilling and low costs are of little value if an inaccurate sample is obtained. The engineer in charge must study his material and lay out the plan of sampling, and then see that the drill runner follows his instructions; for the runner may be more interested in obtaining a large footage than in developing accurate methods of sampling. When the core has been removed from the core barrel, it should be placed in a core box in the exact order in which it is taken from the ground. This box, Fig. 1, is usually a shallow tray 4 or 5 ft. (1.2 or 1.5 m.) long, with partitions running lengthwise between which the core

Jan 1, 1923