Search Documents

By Orson Shepard

TEXTBOOKS on fire assaying list the following standard methods of assaying sulphide ores: (1) scorification, (2) litharge-niter, (3) soda-iron, (4) roasting, (5) combination wet and fire. The litharge-niter method has proved the most satisfactory, and is the usual method for assaying sulphide ores and concentrates. It gives good results when suitably conducted and when lead buttons of uniform size are produced so that the cupellation temperature can be properly controlled. The main objection to the method is the inconvenience of determining the amount of niter to add to each assay charge to produce lead buttons of suitable size from a set of fusions. For the assay of different materials, the niter requirement varies with the particular sulphide minerals present, the amount of sulphide minerals present, the slag composition, and the rate of heating the charge in the furnace. Except for some materials, so uniform in composition that the same amount of niter can be used in assaying all samples, the amount of niter must be determined for each sample to be assayed. This is done by either: (1) calculation from an estimate of the kind and amount of sul-phide minerals present in the sample, or (2) a preliminary fusion. Some assayers use one method and some the other. The estimation method takes the least time; but much experience is required to obtain close estimates on a wide variety of materials. At best, the sizes of the lead buttons obtained vary considerably. The preliminary fusion method usually gives lead buttons of fairly uniform size, although sometimes there is a variation because the oxidizing power of niter varies a little with the charge. This variation can be eliminated by two preliminary fusions: one to determine the reducing power of the ore, and the other to determine the oxidizing power of niter in the charge. The objection to the prelimi-nary fusion is the extra time and expense involved.

Jan 1, 1939

By John W. Straton

The President of the United States signed Public Law 91-173 on December 30, 1969 and the Federal Coal Mine Health and Safety Act of 1969 became law. The Bureau of Mines was required to promulgate regulations to implement the law. Unfortunately, some stipulations of the Act were not technologically possible. The USBM employed many new inspectors and had to instruct both old and new personnel in the requirements of the law. Mine operators and mine workers also had to be informed. There was a fair measure of inconsistency during this period. Progress is being made, however, and it is becoming easier for mining personnel to know what needs to be done. There are some unresolved questions, however, and there still appears to be an appreciable lack of uniformity in the application of the law by the many federal inspectors.

Jan 10, 1972

By W. R. Hibbard, J. D. Nisbet

The high temperature properties of Fe-Cr-Co-Ni base alloys and the effects of hardening element additions on these properties are rationalized on the basis of general principles of alloying. DURING the past few years the base elements in high temperature austenitic alloys have gradually been changed from iron-rich materials to nickel-rich, then to cobalt-rich and more recently to various iron, cobalt, and nickel combinations, all with an approximately constant chromium content of 20 pct. Concurrently, the hardening additions of the incongruous* elements, have been shifted from small amounts of a single element to various ratios of molybdenum, tungsten, columbium, carbon, titanium, and aluminum with the percentages of these constituents continually increasing. It has been known that the typical soft high temperature alloy (such as Inconel) consisted of face-centered cubic austenite, but the effect of varying the composition of the base elements, iron, chromium, nickel, and cobalt, has not been broadly analyzed. Therefore, it was reasoned that the first major problem in the understanding of the properties or the further development of high temperature alloys was to study systematically the effect of composition upon the mechanical properties of face-centered cubic Fe-Ni-Co-Cr austenitic solid solutions. The matrix of the strong high temperature alloys (such as Inconel X) is usually also a face-centered cubic solid solution of iron, nickel, chromium, and cobalt but with additional phases which can be generally classified as intermetallic compounds and carbides. It is usually observed that combinations of the hardening elements, tungsten, molybdenum, columbium, tantalum, titanium, aluminum, carbon, and others have been used in these strong high temperature alloys. Thus, it was reasoned that a second major problem in studying these alloys was to understand the effect on mechanical properties of adding

Jan 1, 1954

By C. E. Lesher

COAL has been fighting a rear-guard action since the last World War. The battle against competitive fuels has been largely guerilla warfare with more sniping within the ranks than of organized opposition. Oil and natural gas are the fuels that over these twenty odd years have driven coal backward and out of many profitable markets. Now, somewhat timidly, the coal industry is trying a new weapon; namely, Research, or let us more properly say, Organized Research. Engineers have been designing this weapon for many years, supported by those interested in coal, including some coal producers. A part of this pioneer work has been Fundamental Research, the Ph.D. kind that is over the heads .of most of us. Another part has been aimed at immediate objectives and realizable profits, the practical, man-in-the-street sort. That is Industrial Research. Enough has been accomplished to make a fair exhibit, but whether this new weapon will have sufficient fire power to rout the opposition, whether the industry will really go into production and use it, the next few years will tell. NEED FOR COAL RESEARCH To utter "Research" is to use the modern magic word; to conjure up the miraculous-rubber from weeds; radar; magnesium from sea water; yes, even gasoline from coal. Research is a very general term. It means something different to every man. What is the coal industry seeking with its research; or what should it seek? And, specifically, how is it going about the job; and is it taking the best way? There are many who say that Coal has been asleep at the switch, while Oil and Gas have been taking the energy business. In an organized way this is true. Large-scale, privately financed research is just started in the Pennsylvania, anthracite industry, and it is still a dream for bituminous coal. What has been done so far collectively is purely defensive; as, for instance, to improve mechanical devices for burning coal so as to be able to recover markets for house-heating fuel long since abandoned to oil and gas. To appreciate just how seriously bituminous coal has slipped back in the national economy in the past 25 years, one has only to recall that, in the last war the Navy required for its operations all the high-grade, low-volatile coal that could be produced, and that anthracite was withdrawn from the middle and northwest markets to keep the eastern seaboard warm. All coal was "rationed" by zones, if not to individuals. Now the Navy, the Armed forces and the Merchant Marine are propelled by oil and gasoline. Gasoline and heating oil are rationed to individuals. Production of all coal in this country in 1918 reached the historic figure of 678,200, 000 tons, and in 1943, after 25 years, it is expected to reach a special wartime total of 660,000,000 tons. Meanwhile, production of crude oil this year may exceed 1,500,000,000 bbl., and like that of natural gas, reach four times the amount produced in 1918.

Jan 1, 1944

By Harry L. Washburn

Use of coal thermal dryers has steadily increased since 1928 when one of the predecessor companies of the present Consolidation Coal Cu. constructed a complete preparation plant with thermal dryers. Today there are about 25 additional preparation plants that, all together, use over 65 individual thermal dryers of almost every type. The thermal dryer is a heat generator and the unit may have a separate furnace or a firebox that is an integral part of the dryer. It is also a materials handling device that allows an intimate mixture of wet coal and hot gases with instrumentation for temperature control and. in some cases, the more difficult flow rate of hot gases. The materials handling portion of the dryer is subject to the normal wear and teal of any similar device plus effects of heat, water vapor, moisture: and, sometimes, acid. With present emphasis on air pollution. most fine coal dryers have wet scrubbers.

Jan 8, 1963

By Rixford A. Beals

Dry grinding without balls is feature of this mill now in use in three countries on two continents. Materials being ground commercially include iron ore, gold ore, asbestos rock, and slag. New large beneficiation plants have been using an almost standardized crushing and grinding flowsheet. Typically a primary gyratory is followed by several stages of fine crushing and grinding is often carried out in a rod mill operating ahead of one or more ball mills. The clearly labeled trend is to an increasing number of stages with a decreased reduction ratio per machine. Current Aerofall mill installations represent a complete reversal of this trend-one mill replaces the several stages of crushing and grinding a more conventional flowsheet would call for.

Sep 1, 1955

By S. W. Parr, T. E. Layng

The low-temperature carbonization of coal involves the carrying out of the coking process under conditions wherein neither the coal mass nor any of the passageways through which the volatile products pass are heated above 700" or 800" C. For convenience in this discussion, the single number 750" will be used to designate the maximum range. This temperature is not selected arbitrarily; it is the result of certain natural conditions that are inherent in the substances involved. Two of these conditions arc sufficiently pronounced to suggest a line of demarcation at this point as follows: (1) Below 750°, all the heavy hydrocarbons are expelled, which means that, at these lower temperatures, the illuminants, the gases of high calorific value, and the condensible oils are discharged; above 750") there are given off the lean, non-illuminating gases consisting for the most part of hydrogen and marsh gas and having no condensible constituents present. (2) Below 750") there is substantially no secondary decomposition; above 750") the volatile products are readily decomposed, forming tars, naphthalene, free carbon, etc. It is not intended to maintain that no secondary decompositions occur below 750". Many recent studies have demonstrated the practicability, especially in the presence of catalytic substances, of cracking certain of the hydrocarbon compounds; but at these lower temperatures the step is a moderate one, as, for- example, from xylene to toluene or from toluene to an anthracene. These changes are moderate in amount. Not only do the reactions proceed slowly but they are subjected to the decomposing . conditions for only a short time. This is evident when it is recalled that at these initial temperatures the decomposition of the coal is very rapid and, if anywhere near a neutral pressure is maintained, the movement of the evolved gases is lively and reduces, correspondingly, the time for the retention of the gases in the passageways where these milder decomposing conditions exist. It is acknowledged that the maintenance of these temperature conditions at the present time has only an ideal and not a practical status. Actual operations under these conditions, as a? industrial accomplish-

Jan 1, 1920

By D. A. Augenstein, L. V. Amundson

Operators of coal preparation plants use equipment such as large-capacity dump trucks and bulldozers to haul, spread, and compact refuse material to conform to federal and state regulations governing the disposal of solid waste. For example, federal regulations require that refuse be spread and compacted in layers not more than 0.6 m (2 ft) thick. If the refuse layers or piles have poor load-bearing characteristics, movement of equipment over them becomes extremely difficult. The increasing cost and limited space for the construction of settling ponds extensively used for fine refuse disposal are leading to the growing practice of dewatering the fine refuse by means of vacuum disk filters and combining the resulting filter cake with coarse refuse for waste bank disposal. However, this filter cake usually contains more than 25% moisture. Therefore, when it is combined with coarse refuse, the moisture level of the total refuse may become high enough to impair the load-bearing strength of the refuse. Precisely this problem and the attendant difficulties of moving heavy equipment arose when vacuum disk filters were installed at a preparation plant in West Virginia. Combining the moist filter cake with the coarse refuse generally results in a 12% moisture level for the total refuse at this plant. At this moisture level, the refuse can still be handled with some dif¬ficulty by the equipment. However, the problem has frequently been compounded after rains. The experimental program described in this paper tested the following methods of improving the load-bearing properties of coal refuse: moisture reduction, addition of crushed coarse refuse, addition of fly ash, addition of lime, and addition of a mixture of lime and fly ash. In terms of a balance between economic and technical considerations, the most effective method was demonstrated by laboratory and plant tests to be a 2% to 5% addition of lime. Test Program During formulation of a test program aimed at improving coal refuse stability, a number of treatment techniques were selected for evaluation of their effect on refuse load-bearing characteristics. The reduction of refuse moisture was the first technique considered, since moisture content plays a key role in the bearing strength of a bulk solid. The reasoning was that a very small reduction in refuse moisture, provided it could be accomplished with minimal effort and cost, would be sufficient for eliminating refuse disposal problems most of the time. At the same time, it was recognized that periods of rainy weather would offset moisture-reduction measures. Other techniques selected for evaluation because of their potential for improving refuse-bearing strength at reasonable cost were: addition of crushed coarse refuse, the addition of fly ash, and the addition of lime. A simple one-dimensional laboratory compaction test was designed for evaluating the effect of each of these techniques on refuse-bearing strength. Those techniques that gave best results in the laboratory would then be tested in the preparation plant in West Virginia. Laboratory Tests The laboratory test for evaluating each of the techniques involved the application of weight to a load module placed on a refuse sample in a container. The distance the load module sank with an increasing amount of applied weight was measured, and the relationship between module displacement and loading was obtained. The refuse container was large enough to minimize the influence of wall effects, and to decrease the effect of the container bottom, a test was terminated when the load module sank to about three fourths the depth of the container. Initially, an attempt was made to conduct compaction experiments with samples of total plant refuse. However, the presence of + 0.13 m (+ 5 in.) material in the refuse interfered with the mechanics of the test, and the large amount of material required for a representative sample made testing extremely tedious and time-consuming. To avoid this problem and because it was believed that only the fine components of the refuse were the major cause of the stability problem, tests were conducted with 13 mm X 0 (1/2 in. X 0) material from the total plant refuse. The equipment consisted of a 0.46 m (18 in.) cubic container, a loading module with 62 cm2 loading area, weights totaling 450 kg, and a portable concrete mixer for combining water and additives with the refuse. Refuse samples of about 110 kg dry weight were used for each test. Experimental compaction test data were evaluated by plotting the linear displacement of the load module vs. loading. During compaction tests, the vertical displacement of the load module was measured at each loading value. The plot of

Jan 1, 1980

By Harold M. Mooney

RESISTIVITY measurements for determining depth to bedrock, water table, and other geo- logic discontinuities have had only limited success. Many of the difficulties can be attributed to complex geology and to basic limitations of the method; current flow through a continuous medium is a diffusion phenomenon, emphasizing irregularities near the source and smoothing out those at a distance. Some of the failures, however, are due to careless field work and incompetent interpretation. A forthcoming publication1 may help to reduce difficulties of this sort. The writer here attempts to bring order into the multiplicity of interpretation methods and, to a limited extent, to evaluate them. For all methods, the field data to be interpreted consist of apparent resistivity values plotted against electrode separation, Fig. 1. The interpretation should give depths to one or more geologic horizons. Direct currents and the Werner four-electrode configuration will be assumed, since these are widely used, although the interpretation problems remain essentially the same for other electrode configurations. Alternating currents higher than, say, 20 cycles per second introduce complications beyond the scope of this paper.

Jan 9, 1954

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has five major awards to make annually for excellence in technical papers, as follows: The Robert W. Hunt Medal, The Hadfield Prize, The J. E. Johnson Jr., Award, The Lewisohn Platinum Prize to senior members, and the President's Prize to junior members. ROBERT W. HUNT MEDAL The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes; first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to. a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five including the Chairman of the Iron and Steel Committee, shall be appointed by the iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the. award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be designated "The Hunt Medallist." SIR ROBERT HADFIELD PRIZE Sir Robert Hadfield has offered an Institute prize of $1000 for researches with regard to the different forms of combination of carbon in iron and steel. Until within a few weeks no paper has been submitted which could compete for this prize. If the paper in hand should not meet the requirements, the donor has suggested that the prize be transferred and offered for: (a) the determination of the hardness in metals in connection. with super-hardness, (b) in consideration of questions of fuel economy, (c) in consideration of questions of industrial development and labor. J. E. JOHNSON, JR. AWARD This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practise, vice-chairman of the Institute's Iron and Steel Committee, and a frequent contributor of papers to the Institute's TRANSACTIONS.

Jan 1, 1925

By Edward Martinez

The literature on the beneficiation of serpentine asbestos ore states that the specific gravity of the rock containing fiber and the fiber itself is the same so that specific gravity cannot be used as a basis for separation. An investigation of particles of asbestos ore ranging in size from 4 mesh to 5 in. revealed that the fiber-bearing particles generally had a lower specific gravity compared to essentially barren particles. The difference in specific gravity was sufficient to make an effective gravity separation of ore particles and reject a low grade tailings product. The results of laboratory tests are described that lead to the running of pilot plant tests with 20-ton ore samples using a heavy media separator. These tests indicated that a large amount of low grade material could be rejected from the raw ore at a coarse size. Although the process used is a wet separation, it can be added to a conventional dry asbestos mill. A gravity preconcentration would allow the mining of lower grade ore, increase the life of the mine, increase the value of the feed to the fiber recovery section, and decrease maintenance costs by removal of low grade tailings early in the flowsheet.

Jan 1, 1975

By J. Wayne Erickson

One of the major problems facing today's mining industry is how to manage people and control costs in the underground mine. It is a problem with a solution. Because of the concerted effort to find and mine minerals near the surface, open-pit mine opportunities for certain minerals are becoming more limited; the mining industry will eventually be forced to produce more and more from underground mines in order to obtain those resources necessary to sustain our civilization. Although much technical progress has been made towards solving problems associated with the underground mine, such as - mine design, ventilation, rock support, equipment, and blasting techniques, little has been written on managing mining personnel. Much of what is being taught and practiced today about human relations, motivation, incentives, etc., applies to the underground miner, but the uniqueness of his group dictates a different treatment from that associated with the typical construction worker or factory employee. The difference lies with the kind of man attracted to underground mining and his working environment. Anyone who has had the responsibility of managing an underground mine would agree it is a unique problem.

Jan 9, 1976

F. C. LANGENBERGW.*at 8ertoivn,M ass. (written cliscussiont).-I am inclined to the view that the change in physical properties encountered in the material with which the authors are working is due to the relief of internal strains. The statement, on page 1.098 of their paper, calling attention to the fact that this phenomenon disappeared when the material was rolled into 1 7/8 -in. square billets is of particular interest. It is certain that the internal strains set lip by cooling in a small billet of this size would be much less than those produced in a billet having a larger cross-section cooling under the same conditions. The statement that the physical properties of a given test bar were materially changed by standing has been brought to my attention in connection with the testing of gun forgings. I have made a number of observations on forgings produced at Watertown Arsenal to ascertain whether any change in ductility was produced by the aging of the test specimens. The results were always negative, but this can be explained by the fact that ii gun forging is generally a forging that has been quenched and subsequently drawn at a relatively high temperature.

Jan 10, 1919

By James A. L. White

Of the natural elemental surfur deposits of the world, volcanic deposits are not only the most spectacular, but probably the most widely distributed. As defined for the purposes of this paper, volcanic sulfur deposits include those associated with all phases of volcanic activity, including eruptive flows, and fumarolic and hot spring deposits. The line of demarcation between the latter and sedimentary deposits is not always clearly defined. Although volcanic sulfur has played an important role for centuries, serving as essentially the only source of sulfur, currently it is considered as purely marginal material. Volcanic deposits were relegated to this position by the advent of Frasch sulfur into world markets, which established sulfur prices and annual production levels with which volcanic sulfur cannot compete, Since early in the 20th century commercial interest in volcanic deposits of sulfur has been high only when premium markets are available. This occurred in the early 1950s and is the case at present. Considerable effort is currently being expended to establish new producers of volcanic sulfur, and to expand current operations or reactivate previous ones.

Jan 6, 1968

By C. F. Tolman

Discussion of the paper of C. F. TOLMAN, JR., presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 401 to 433. Louis C. GRATON, Cambridge, Mass.-Of particular interest at this time is any paper that deals with chalcocite, the characteristic product of secondary enrichment and the copper mineral of greatest commercial importance, and that seeks to aid in the distinction between primary and secondary chalcocite-a distinction of much scientific and practical importance but one which thus far it has proved difficult to draw. The present paper on this subject by Professor Tolman, like the ,many preceding it which he and his colleagues at Stanford have published in the last couple of years, contains much of interest and suggestiveness. Without endeavoring at this time to review or comment upon Professor Tolman's conclusions in detail, I may say that many of them are in accord with the findings that my associates and I have been accumulating in the course of studying secondary enrichment in many of the copper deposits of the country. On the other hand, it goes without saying that in this comparatively new field of research or, at least, a field in which

Jan 5, 1916

By Gary Mack, Donald E. Scheck

To help management keep key machines or processes at peak efficiency, draglines, shovels and blast hole drills have been equipped with micro- processor based monitors. The dragline and shovel monitors log operating data such as energy consumption, bucket position, cab rotation and the clock time of key elements within each cycle as well as maintenance information. The output consists of maintenance and management data such as the number of cycles, average cycle times, swing angles, depths and downtimes. Extensive experimentation has shown that a blast hole monitor can provide a log of each blast hole in which the hard to fragment zones are indicated. The logs are printed on board the drill and serve as the design basis for decked loading of the holes. As a result, the fragmentation of the overburden has improved markedly with the same or less powder consumption. This material is based upon work supported in part by the Bureau of Mines, Department of the Interior under Grant Numbers G1115006, G1115391 and G5 105006. Any opinions, findings, and conclusions or recommendations expressed in this publication are those of the authors and do not necessarily reflect the views of the Bureau of Mines, Department of the Interior.

Jan 1, 1983

By A. S. Richardson

The design of mine airways receives, in general, very little engineering treatment. To a large extent this is, of course, due to the fact that information upon which to base calculations is seldom available in definite form. In many rnines the extent of the workable deposits may not be known at the time an air course is planned, and the length of service is indeterminable. Volume of air required for ventilation rnay also increase with extension of the life of a property, and natural obstacles, such as heavy ground, often place limitations upon the size of opening that can be maintained. Perhaps most of the shafts used in the ventilation of metal mines were originally intended as hoisting shafts, and many of the tunnels and crosscuts similarly used, were also designed as haulage ways or for other operating purposes. Even when a shaft is sunk solely for ventilation, custom usually dictates a size and shape consistent with the type commonly used for ordinary operations, because experience has demonstrated it can be excavated and maintained. In fact, most ventilation openings were never made with any consideration as to economic design for such use. When an air course is required to pass air between different parts of mine workings under a fixed pressure, the size of opening required for a given volume of flow, is, of course, determined by the resistance factor of the air course. It is then impossible to proportion the opening with reference to economics of power consumption, and this paper is limited to the design of openings where ventilation pressure or power consumption may he varied for economic advantage. As the size of an air course is increased, the expense involved in excavation and support is, of course, also increased, but the charge for power is decreased. In the case of a mine that has only a short assured operating life, it would not be ecouomical to provide large openings in order to reduce power bills; but when operations are likely to continue for a long time, the power charge becomes a very important economic factor. Although lack of definite information on such factors as service life and costs of excavation and support affects the design of an air course, it appears, from a mathematical analysis of the problem, that considerable variations may be made in estimating these factors, without greatly

Jan 1, 1927

By E. D. McMurry

INTRODUCTION Before discussing the use of the free piston; it may be well to explain briefly the type of gas lift valves with which the loo] is designed to function. The gas lift valve ii nothing more or less than a small back pressure regulator. It; construction consists of an outer hous ing covering a seamless metallic bellows in such a way as in form a sealed pressure vessel or pressure dome. To the bellow* in attached a stem and to this stem is attached a .rating member. When the valve is run into the hole, a pre-delermined pressure charge is placed in the pressure dome. As shown in Fig. 1. the valve is furnished in four different major assem-blies. to accomplish good results in different types of wells. The valve is mounted on a pup joint (Fig. 2a) : the eoin-plele assembly is entered into the tubing siring at the desired location. Each valve is furnished with a revere flow check valve (Fig. 2-b) to eliminate any back wash through the mechanism. Valve action is as follows: At any time the casing pressure is allowed to exceed the pressure forces within the pressure dome of the valve, the valve simply opens and passes gas from the rasing annulus into the tubing. When the casing pressure forces arc allowed to bleed to a force less than the pressure force within the dome, of the valve. the valve closes. With this type of construction. it is possible to open and close the valve or valves at will from the surface, the medium of the gas pressure in the rasing annnlus. The cycle of operation is governed by a tine cycle motor valve, commonly referred to as a gas lift interutitter or gas life surfacr controller (Fig. 3). In actual practice. after the well is unloaded only one valve is in operation . . . all other valve.: remain in the closed position. On pre-determined time cycles, it is possible to open and close this operating valve at will, and to pass the desired amount of gas through this valve wheneler needed. This method of gas lift is widelv used and has been found In be very efficient. However, it has long been known that even greater efficiency would be obtained if it were possible to place Piston between the injected gas and the fluid head. The free piston which will be discussed here was designed to accomplish this end and has been found to do so with very satisfactory results. DESIGN AND OPERATION OF THE FREE PISTON Basically. the free piston consist- of a telescoping assembly in which are incorporated the various control and operating parts (Fig. A set of sleeve valves which are opened and closed by movement of the telescoping section is contained in the. tool. A cross section of the free piston is shown in Fig. 4-11, 'rile main body cotain- a seamless monel bellows of the same type as that generally used in pressure charged gas lift valves (Fig. 4-c), and a valve core to permit placing a pressure charge in the bellows before the free piston is placed in service. The bellows is the main control unit of the free piston and performs two function: 1. It governs the opening and closing of the sleeve valves. a.: dictated by the producing activities of the well in which the piston is operating. 2. In its normal position, it holds a rubber packer in an elongated position to permit passage of fluid between the packer and the tubing walls. The lower section of the free piston contains a hydraulic shock absorber which cushions the return of the tool to its

Jan 1, 1953

By G. Carman Ridland

IN conjunction with a geological investigation of the silver-bearing veins at Contact Lake, Northwest Territories, Canada, a survey was made with a Geiger-Müller counter of the gamma-ray emissions from the rocks in the vicinity of the mine workings. Discontinuous pitchblende veins have been encountered occasionally in the silver-bearing fissures, and the geophysical survey was undertaken with the hope that abnormally high gamma-ray intensities, if detected, might lead to larger and more continuous pitchblende discoveries. Before the instrument was used at Contact Lake, preliminary tests were made, first with laboratory specimens at Princeton University, and later over known pitchblende deposits at the Eldorado property, LaBine Point, N.W.T. The Geiger-Müller counter, as adapted for field use, is described; the technique of transporting and operating the instrument is outlined; and the general precautions to be observed are discussed. The results obtained at Great Bear Lake show that the instrument is capable of detecting not only a pitchblende ore shoot in a shear zone, but also the mildly radioactive "host rock" at a considerable distance from the ore body. Hence, use of the Geiger-Müller counter is urged, not just for the detailed search for an ore body in a shear zone, but for the detection of possible radioactive "host rocks" in large-scale reconnaissance surveys of unexplored regions made by prospectors and members of federal geological survey parties.

Jan 1, 1943

By F. N. Lewis

HOPPERS may be divided into three classes accord-ing ing to type, namely; round, suspension, and square or rectangular. The round hopper is the most simple of the three and is the most easily understood by laymen. The bursting pressure in these hoppers is resisted by the shell as a round tank resists the pressure of water. They are perfectly stable as long as they retain their cylindrical shape. In holding water or other liquids the pressure on the sides is always the same, but with ore this is seldom true. These round hoppers for ore are usually filled from one side and frequently drawn off from the opposite side. A considerable amount of fine material is deposited on the side of filling, while the coarse particles run over to the far side. This con-dition of filling causes the ore to flow out unevenly, sometimes drawing out completely on one side. After a time the remaining ore breaks down and the shock of this falling ore, sometimes many tons, is very severe and has a tendency to distort the hopper from its true shape; consequently a round hopper holding ore should be stiffened to resist such shocks as this. For these reasons round hoppers have never been popular with engineers for holding ore. They also have a trait of welling. up worse than the square hoppers. I have known of round hoppers holding fine ore, 25 ft. diam-eter, that had a tendency to well up until there was ,only a round hole about 6 ft. diameter leading to the gate. The suspension or catenary type of hopper is well adapted to conditions requiring only small capacities. The selection of this type of hopper should be done with considerable care. The theory of the design is that the loads are carried entirely in tension in the bottom plate, just as a hammock carries a load, and it must be remembered that the bottoms of these hoppers are con-stantly changing form with the changing loads. Take a hammock, for example, if a person stands up in it, the bottom goes down and the sides approach a straight line; if the person lies down then the bottom comes up and the sides go down. It is this constant changing of the form that has a tendency to break the connections.

Jan 7, 1928