Search Documents

By A. Dubnie

Three periods of major activity have led to the development of the present mineral industry in northern Canada. At the turn of the century, placer gold was discovered in the Yukon Territory and production has been continued to the present day. In the late 1920's and early 1930's, vigorous aircraft- aided exploration resulted in the discovery and production of radium at Port Radium on the southern shore of Great Bear Lake and of gold at Yellowknife on the north shore of Great Slave Lake. During this period, oil was discovered at Norman Wells. Present mineral production is today largely derived from deposits which have been developed in the 1950's. Among these are the re-opened deposits of United Keno Hill, uranium deposits at Uranium City, natural gas resources from the Peace River gas area, nickel-copper deposits at Lynn Lake and Rankin Inlet, and the Cassiar Asbestos deposits at McDame Mountain.

Jan 5, 1961

By A. H. Dierker

Next to the metal itself, molding sand is the most important raw material used in the manufacture of steel castings. There are no accurate figures available but probably it would be safe to say that the average steel foundry uses approximately 1000 lb. of new molding sand per ton of castings produced. With untreated sands costing from two to four dollars (in some extreme cases it may run as high as eight or ten dollars) per ton delivered at the foundry siding, molding sand is an important item in the cost of making castings, and any information that may help to reduce this sand consumption should be of interest to the industry. Fundamental Considerations In a general way, molding sand in the average steel foundry passes through the cycle shown in Fig. 1. This diagram indicates that if all of the sand could be returned from the shakeout floor to the mixer no new sand would be required from the stock pile and molding costs would be reduced accordingly. Unfortunately, for reasons to be discussed later, it has heretofore been necessary to dilute the used sand constantly with new raw sand in order to maintain the properties that are essential to the production of satisfactory molds.

Jan 1, 1930

By J. H. Wernick, S. Geller

A number of new AB, compounds, in which A is a rare earth or yttrium atom and B is Al, Mn, Fe, Co, or Ni, having the cubic MgCu, structure (Laves phase) are reported. In most of the compounds, the interatomic distances are normal; the lanthanide contraction is observed. However, in the compounds CeB2, B = Fe, Co, Ni, Ce appears to have a valence substantially greater than three; in CeAl2, Ce appears to be trivalent. These results are interpreted as vesulting from an energetically more favorable situation for the 4f electron of Ce to be lost to the 3d band of Fe, Co, nnd Ni. Evidence for the existence of homogeneitj! ranges in these compounds is presented. THE purpose of this paper is to report on the crys-tallographic investigations of a large number of new compounds, Table I, with the MgCuz structure (cubic Laves phase). It is a part of a continuing study of the magnetic properties and structures of binary systems involving the rare earths. In a previous paper' some of the magnetic properties of such systems were reported briefly. We have also reported2 a number of compounds of the CusCa type. The compounds were prepared by induction melting in Argon atmosphere of mixtures of stoichiomet-ric amounts of the constituent elements.* For most of the compounds fused alumina or silica crucibles were used as the containing vessel; graphite crucibles were used to prepare CeA12, NdAl2 and TbA12. X-ray powder photographs were taken with CrKa radiation and the use of Straumanis-type Norelco cameras of 114.6 mm diam. The compounds AB2 belong to space group Fd3m-Ol with 8A in a): (000; 01/2 '/2;3) + 000-; b % XA and 16B in dl: (000; oVa %; 3) + 5/87; % %; 7e % Vs\£>. Because the intensities of the reflections on the powder photographs of the different compounds are similar, relative intensities were computed only for DyMnz for CrKa radiation, Table 11. In the calculation of intensities, the Thomas and umeda3 atomic scattering factors, corrected for dispersion,4 were used. The agreement between observed and calculated intensities leaves little doubt that DyMnz has the MgCuz structure. Crystallographic data for the ABz compounds are given in Table JII. Twelve of these compounds have been reported by other authors. A comparison of the published results with our work is given in Table W.* ers of elements of lower purity, to peritectic reactions in some cases, and to the presence of homogeneity ranges in these alloys, so that melting losses would still result in single phase alloys. The possibility of existence of homogeneity ranges in these compounds was investigated systematically only for GdMnz. At room temperature, the solid solution range is between

Jan 1, 1961

By S. K. Bradford

For years past I have traveled in quest of promising mining-properties, over almost impassable mountain-trails to remote places in the mining-regions, usually many miles from an assay-o5ce. If, upon examination, the fornlation and the ore-deposit appeared favorable, a quick determination of the value of my samples was necessary, in order that I might take intelligent action with reference to the acquisition of the property. A journey with my samples to civilized regions often meant weeks of delay, and perhaps loss of opportunity. How many, under similar circumstances, have returned with their assay-results from such a journey, only to find that some audacious speculator had optioned" the property! True, a first payment could have been made and the chances taken on the results; but experience has taught that rich-looking ore is not of necessity valuable. Personally, I would not hazard a ten-dollar bill on any property without first determining by assay the value of the ore. To carry the usual complete assay-paraphernalia over such mountain-trails was impracticable by reason of the loss of time involved, the great expense of transportation (charged -

Jan 1, 1911

By Percival Roberts

It may seem necessary to offer an apology for presenting for consideration a process which is conspicuous by its absence in the literature of the Institute, and which may be thought by some to belong to the past in metallurgy, and to have been already superseded. But the large capital invested in puddling calls for a careful consideration of the question whether the time has certainly arrived when the puddling furnace must be replaced by the converter and open-hearth furnace. May there not still be a place for puddled iron alongside of molten iron and steel, and is not the improvement of the puddling process itself worthy the attention of engineers equally with the Bessemer and open-hearth processes? The changes involved in the conversion of pig iron into wrought iron are well understood and need only be briefly alluded to. The patent of Henry Cort bears the date of 1784. Since that time * the improvements in the process have mainly consisted in the replacement of sand by iron bottoms by Samuel Baldwyn Rogers in 1818, and the still more recent substitution of iron oxide for the refractory materials used for the rides and bridge of the hearth, which distinguishes the wet or boiling process from the dry or pnddling process. Chemically, the process consists in the removal of the metalloids from the pig iron, a result effected mainly by the iron oxide. Silicon is first oxidized, then the phosphorus, and finally the carbon. The silicic and phosphoric acids produced pass into the cinder and the carbonic oxide burns as it escapes from the bath of metal. It is interesting in this connection to note the effect of temperature on the removal of the phosphorus from the iron. As is well known, no phosphorus is eliminated under the oxidizing influences prevailing in the Bessemer converter, while from 70 to 80 per cent. is removed in puddling. But we find, if in working cold short irons

Jan 1, 1880

By B. E. Hoffacker, R. E. Lund, J. Ferrighetto, G. E. Welch

Since October 1965 the Josephtown Smelter of St. Joseph Lead Co. has commercially applied the Heavy Media Separation process to reclaim zinc and reject gangue from electrothermic zinc furnace residues. In addition, heavy medium is produced from the ferrosilicon which is present in the furnace residues. By way of background, the Josephtown Smelter produces zinc metal and zinc oxide by the electro- thermic process. The principal feed to the vertical shaft electric furnaces is sized sinter and coke. Temperature of the charge in the furnaces varies from roughly 900°C near the wall to 1300-1400°C in the central regions. Zinc smelting is rapid and nearly complete in the main body of the charge, but little zinc is smelted near the wall. In addition to fusing high gangue content particles, the high temperatures promote side reactions, the most important of which is reduction of iron oxide and silica to form a low grade ferrosilicon containing about 82 % Fe and 13% Si.

Jan 12, 1968

By T. A. Rickard

The lodes of Cripple Creek, Colo., partake of the composition of the geological formation which they traverse. The prevailing rocks are andesitic breccia, lying upon granite, and also bodies of phonolite, trachytic phonolite, nepheline-basalt, etc., penetrating both the granite and the breccia. At Kalgoorlie, in West Australia, the prevailing rock is schistose, and has not been certainly identified, though microscopic sections indicate the probability that it was originally an acid eruptive. The lodes are essentially bands, more highly schistose than the encasing rock, and impregnated to a notable degree with disseminated pyrites and secondary calcite. During 1899 Cripple Creek produced 425,590 tons of ore, having a gross value of $15,658,254; during the same period the output of Kalgoorlie was 467,048 tons, valued at $17,724,587. In chemical composition, the ores at Cripple Creek and Kalgoorlie, respectively, present differences equally interesting to the petrographer and the metallurgist. In both cases we have to deal with altered eruptives as the matrix of the ore; but the much older rock of Kalgoorlie has undergone more decompo-

Jan 1, 1901

By J. T. McGrath, R. C. A. Thurston

Poly crystalline specimens of copper, and copper with various additions of zinc, were tested in plane-bending fatigue. In tests performed at a constant stress, the fatigue life of copper increased slightly with the addition of up to fifteen per cent zinc. There was a sharp increase in fatigue life as further additions of zinc of up to 35 pct were made. Surface observations showed that the coarse slip bands that are characteristic of fatigue became narrower as the concentration of zinc increased. The rate of crack propagation also decreased with increasing zinc content. It is suggested that the fatigue behavior is controlled by cross slip processes. CROSS slip occurs when dislocations move from one primary slip plane to another along a connecting or cross slip plane. The primary and cross slip planes have a common slip direction. Wide stacking faults, having low energy, tend to make cross slip more difficult. According to recent theories, the ability of a material to cross slip is important to the formation and propagation of fatigue cracks. McEvily and Machlin2 have examined this concept experimentally by fatiguing single crys tals of lithium fluoride, sodium chloride, silver chloride, and KRS-5.* The latter two materials ex- hibit easy cross slip, while the former two do not. Normal rapid fatigue failure was obtained in the silver chloride and KRS-5 specimens, whereas it was much more difficult to achieve in sodium chloride and lithium fluoride crystals. Furthermore, numerous slip band extrusions and intrusions were found in silver chloride and KRS-5 crystals, whereas only one isolated extrusion was found in lithium fluoride and none was found in sodium chloride. McEvily and Machlin also consider that there is no clear-cut demarcation between crack initiation and propagation. The intrusion-extrusion process, which initiates crack formation, continues ahead of the cracks to allow propagation of these cracks along slip bands. The process of cross slip is therefore important not only to crack initiation, but also to crack propagation. Holden4 postulates that fatigue crack growth is dependent upon cross slip and thus upon stacking-fault energy. Using an X-ray microbeam technique, he found a cyclic subgrain structure in fatigued aluminum and a-iron. Holden suggests that micro-cracks develop in the densely-packed sub-boundaries ahead of the main crack front, and when sufficiently numerous join up to promote crack growth. The ease with which a subgrain structure could form would depend upon the ability of the dislocations to cross slip, and thus upon the stacking-fault energy. Hence in aluminum, which has a high stack-ing-fault energy and in which cross slip is easy, Holden found that the relative rate of fatigue crack propagation was considerably greater than in stainless steel, a low stacking-fault energy material. It has been shown by a number of investigators that the probability of forming deformation stacking faults in copper increases as zinc is added.5-7 Cross slip should, therefore, become more difficult as the zinc concentration is increased. In order to check the validity of the foregoing theories, it was decided to test copper and copper with various additions of zinc in plane bending fatigue, and determine to what extent their fatigue properties are dependent upon their ability to cross slip. EXPERIMENTAL PROCEDURE Fatigue tests were carried out on polycrystalline OFHC copper and various copper-zinc alloys with 5, 15, 20, 30, and 35 wt pct Zn. The Cu-Zn alloys were obtained commercially in sheet form. Test specimens, as shown in Fig. 1, were machined from sheet that had been reduced to an approximate grain size of 0.040 mm, the heat-treatment procedure being similar to that of Feltham anc copley.8

Jan 1, 1963

By H. R. Joesting

Geophysical search for minerals is stepped up to meet requirements of expanded defense program - Seismic and electrical surveys become firmly established for ground-water and engineering investigations.

Jan 2, 1953

By Joseph D. Weeks

The primary problems of civilization are material ones; their answers are writ in fire. When these problems in their higher aspects have pressed for solution, it has been out of the burning bush that the Divine voice has spoken, or in the cloud and smoke that the Divine finger has traced the rules by which these problems shall be solved. It is with the material problems, however, that we, as engineers, have to deal.

Jan 1, 1896

By Frank Doxey

Louis A. Turnbull (U.S. Bureau of Mines, Washington, D. C.)—This paper is a well-organized concise discussion of progress in mechanization at coal mines in Nova Scotia during the last 50 years. It shows the perseverance and resourcefulness of those responsible for the production of high-quality coal essential to steel production in the area. The development of the Dosco miner and its use in longwall mining at the Sydney

Jan 1, 1955

By J. A. MacLellan, John C. Bowling, J. R. Davenport, G. M. Ellis

Six months out of the year the cold is always there, and it seems to be waiting for someone to make a mistake. The simplest things can shut down a multi-million dollar plant besieged with -40°F temperatures and a 40 mph wind. It takes only one man-door improperly latched to feeze up all the pumps on the bottom floor. Someone can poke a one inch hole in an outside wall in July and six months later, the whole plant is flooded because the main water line just froze up and burst. Some important things must be remembered in plant design for cold and remote areas. For one thing, everything in these areas is more expensive due to long and difficult supply lines. Fuel is expensive and would be a major cost item even if it were not expensive, due to the extended periods of low temperatures. Building volumes should therefore be kept to an acceptable minimum. Service areas, on the other hand, must be adequate, because maintenance generally has to be conducted inside in a heated area. Supply vehicles, for instance, have to get completely inside the building to unload. If you try to unload a supply vehicle with the door open at -50°F, you won't be able to find the vehicle for fog and if you take more than 5 minutes half the water lines in the plant will freeze UP.

Jan 1, 1972

By A. S. Richardson

THE rating of a mine ventilation fan, or the characteristic curves illustrating the duty it may be expected to perform under various mine conditions are, in general, determined by the fan manufacturers. The information is of importance to the operator, or engineer, of a mine in many ways. For instance, when an increased flow of air is desired and the fan speed is to be increased, it becomes necessary to know what increase in volume may be expected and what the power requirements will be. In other cases, it may be decided to make changes in the mine to reduce the resistance to the flow of air, or to make changes in the general system of ventilation. Under any changed mine conditions there will be a difference in the duty performed by the fan. When mechanical ventilation is adopted, the factors governing the selection of equipment for the new system include not only the requirements of existing conditions, but also those that may be expected with the development of the property. Efficiency of service is required over a variable range of operating conditions. Characteristic curves, giving the duty performed by their fans under variable resistance conditions, are published by most fan manufacturers. General statements as to the effect of variation in speed of the centrifugal-type fan, under fixed mine conditions, appear in textbooks and trade catalogs. However, to the author both sources of information appear to be unreliable, at least under certain circumstances. The catalog of a leading fan manufacturer says: 1. The volume of air delivered by a fan varies directly as the speed. 2. The pressure, or water gage, produced by a fan varies as the square of the fan speed. 3. The horsepower of a fan varies as the cube of the fan speed. While these statements are accurate when the fan is operating under conditions similar to those that exist when a blower is used to force air through a pipe, they are not correct under mine conditions that are by no means unusual. Such conditions may be found in deep mines operated through shafts, in which a wide range of temperatures may be

Jan 8, 1925

By William L. Zeller

IN the past 75 years industrial engineering has been highly developed in many fields, but the coal mining industry has just begun to realize its potential for cutting costs. To receive the maximum benefit, a company should apply industrial engineering from the time a new installation is contemplated, but the principles can also be used to reduce and control the costs of an established operation. One company that had been mechanized for seven years reduced its total labor cost 57 pct by industrial engineering. Of this reduction, 20 pct was brought about by a preventive maintenance, rebuilding, and scheduled lubrication program that eliminated 80 pct of the delay caused by mechanical and electrical failures. Thirty percent of the cost reduction was attributed to rearranging the work force into crews of the most effective size, changing working methods, and training all mine supervision in the principles of the cost reduction program. The remaining 7 pct reduction was brought about by a wage incentive program for all the men in the mine. The productivity of this coal mining operation was increased from less than 8 tons per payroll man to 20 tons. This increased productivity was brought about while using the same equipment, men, and supervision.

Jan 12, 1957

By C. Feng, P. Levesque

HE addition of rhenium to molybdenum is known to produce alloys with good workability.&apos; Lawley and Maddin found that the critical stress for twinning in this system was lowered by the addition of 35 pct Re, which suggests that twinning may re- place the usual slip operation as the major element of deformation. The twinning elements in bcc Mo-Re alloys have been reported as the (112) planes and the <111> directions.3 This note represents the continuation of this investigation, in which the authors found that the occurrence of twinning promotes the formation of a bcc tetragonal phase, previously identified as u by Greenfield and Beck.4 Specimens of Mo-35 pct Re alloy, prepared as described previusly, were solution annealed at 2400o, cooled to room temperature, and plastically deformed by compression to induce twinning. After subsequent aging for 8 hr at 1300°C, traces of a were observed along the grain boundaries and at the interfaces between the twins and the matrix, Fig. 1. With increased aging time the cr phase grew into larger clusters and finally occupied the entire twinned area, Fig. 2. Experiments also indicated that if twinning did not precede aging, there was no visible evidence of a in the microstructure.

Jan 1, 1962

By C. V. Millikan

TEMPERATURE measurement in wells is an old practice and geothermal gradients have been of interest to geologists for many years.1,2 Their application to the operation of oil wells is a more recent practice. It has long been recognized that temperature anomalies occur in drilling and producing wells but thermometers that could obtain a satisfactory record of the anomalies were not available.3 The normal geothermal gradient is con-sidered as being about one degree Fahren-heit for each 60 ft. of depth.4 This "nor-mal" gradient varies in different areas, but whatever it may be in an area there is little variation from the surface to as deep as the drill penetrates. The normal gradient is appreciably changed by gas expanding from the reservoir into the borehole or by the movement of fluid through a borehole while drilling, producing, or circulating. It is the resulting anomalies and abnormal gradients from which conditions in wells can be interpreted. Some of the applications of such interpretations are locating the position of oil or gas sands, permeable strata in a reservoir zone, gas-oil contact, source of water, casing leaks, and the top of cement behind casing.

Jan 1, 1940

By S. Floreen, H. W. Hayden

The effects of additions of iridium, rhodium, ruthenium, and platinum on the mechanical properties of Fe-C alloys were determined. Each alloying element significantly improved the toughness. The results support the general correlation that substitutional alloying elements that stabilize austenite are beneficial to toughness, but the reason for this improvement is not obvious at this time. The effects of substitutional alloying elements on the toughness of steel has long been a subject of both practical and theoretical interest. Despite the obvious importance of this subject, there has been little progress toward understanding the mechanisms by which alloying elements influence the fracture behavior. In some cases the deleterious effects of alloying elements have been shown to be due to mechanisms such as embrit-tlement of prior austenite grain boundaries or inhibition of cross slip in the ferrite lattice. In other cases, however, the reasons for the change in properties are not clear. This is particularly true for elements, such as nickel, that improve the resistance to brittle fracture. Several investigators&apos;-3 have pointed out that there is a correlation between an alloying element&apos;s phase diagram with iron and its effect on toughness. Those substitutional alloying elements that stabilize austenite generally are beneficial to toughness, while ferrite-stabilizing elements generally are detrimental to toughness. The word "generally" should be emphasized, because exceptions to this rule can be found. Nevertheless, this correlation does offer a starting point at which to try to understand the effects of alloying elements on toughness. Thus far only two austenite-stabilizing elements, manganese and nickel, have been considered. In order to test the validity of this correlation several other austenite-stabilizing elements were evaluated. The noble metals, iridium, rhodium, ruthenium, and platinum, have binary phase diagrams with iron similar to the Fe-Ni and Fe-Mn diagrams. That is, each element expands the austenite field, and also higher concentrations of each element produce martensitic transformations at low temperatures. Presumably then, each of these elements should improve the toughness of steel. The present study was conducted to determine if this were so. EXPERIMENTAL PROCEDURE The alloys were made as l-lb air-induction melts using electrolytic iron and commercially pure noble metals. Each heat was initially deoxidized by a carbon boil, and further carbon was added to attempt to produce a 0.05 wt pct C content in each alloy. Before pouring, a final refining addition of 0.2 wt pct A1 and 0.1 wt pct Ti was made to each heat. The alloys were cast in a copper mold to produce ingots approximately 1 in. in diam and 5 in. long. The chemical compositions of the alloys tested are given in Table I. The residual nitrogen, aluminum, and titanium contents were all relatively constant at 0.003, 0.03, and 0.02 pct, respectively. The carbon

Jan 1, 1968

By Frank R. Van Horn

In the summer of 1908, R. B. Cochran, Superintendent of the Compania Metalurgica Mexicana at Sierra Mojada, Mexico, presented to the Department of Geology and Mineralogy at Case School of Applied Science an interesting series of silver-, copper-, and lead-ores from the Veta Rica mine. These ores contained several interesting minerals which were associated in a somewhat peculiar manner, so that I was impelled to make a closer study of their occurrence. The investigation has brought out several new facts concerning the geology of the district and the geological occurrence of the ores, and therefore has seemed worthy of record. Two papers have been published previously about the region, one by Chisml in 1887, and the other by Malcolmson² in 1902. These articles, however, treat of the district more from the stand-point of the metallurgist and mining engineer, and not much attention is devoted to its mineralogy and economic geology. 11. Geographical Location of the District. The Sierra Mojada is situated in the extreme western part of the State of Coahuila, near the Chihuahua boundary. It is reached best via the Mexican Central railroad from El Paso, Tex., to Escalon, Chihuahua, a distance of 494 miles. From this point, a branch line, the Mexican Northern railroad, runs 78 miles in a NE. direction to the mines, which are its northern terminus. The railroad was built about 1890, practically on account of the Sierra Mojada mining-district.

Jan 1, 1913

By R. DiBella, H. Biloni, G. F. Bolling

A study of the detailed relationship between solidification substructure and microsegregation in dilute tin alloys has been continued. New observations reveal that depressions form at the solid-liquid interface not only as an initial form of segregation but throughout the range of increasing constitutional supercooling. In order to show the importance of this node formation it proves convenient to make two simplifications. Although substructure changes continuously as constitutional- supercooling increases,&apos; the following discrete stages may be used for discussion: 1) the planar solid-liquid interface; 2) ordered nodes, or depressions at the interface;&apos; 3) two-dimensional or elongated cells;3 4) regular or hexagonal cells;4 5) distorted cells, or hexagonal cells with branches;4 6) dendrites. It is also convenient to ignore observations made near grain boundaries which interact with the cellular substructure.2-4 And, it should be clearly pointed out that all singular depressions at the solid-liquid interface will be called nodes. Heretofore, the term "node" has been used without clear justification to describe both the truly isolated depression and the junction of cell walls appearing in a later stage of segregation. This usage is continued because it seems proved by the observations. Standard systematic growth of tin crystals was undertaken over a broad range of constitutional supercooling using various added solutes. Except for one or two chance observations, this research failed to reveal any appreciable range of growth conditions over which a disordered array of isolated nodes exists. Even though &apos;some finite range of random instability must exist, it is now concluded that stage one passes very rapidly to stage two. Next, after confirming that stage two passes to stage three by the elongation of isolated nodes: a reexamina-tion of stages three, four, and five followed. Standard metallography showed that pockets of higher solute concentration (for ko < 1) became more numerous in cell walls the more severe the growth conditions. These high-concentration regions must arise from depressions; however, in stage three their segregation is not distinguishable from the segregation of the nodes which join cell walls together. It seems, therefore, that the presence of nodes is causal in the formation of new cell walls, and that the mechanism by which stage three passes to stage four is initiated by nodes. If a similar reasoning is followed, the separation of stage four from stage five appears to be just a convenience that has arisen from the decanted interface observations made in the past. The present observations again show that more severe growth conditions relate directly to an increase in the number of nodes in the hexagonal cell walls. These nodes apparently serve as the origin for lines of segregation extending within the body of a cell, and can thus be assumed to represent the earliest form of branching,* as shown here in Fig. 1. The examination of stage six involved decanted-interface structures as in Fig. 2, which are similar to those considered by Rutter and Chalmers,5 Plaskett and winegard,6 and Hellawell and Herbert,7 and where distinct protrusions are each surrounded by a depressed boundary. The corresponding microsegregation behind the interface, but not far enough behind to allow a smearing of the segregation because of diffusion,4 is shown in Fig. 3. Both the shape of the decanted interface and the segregation pattern behind it

Jan 1, 1968

By David J. Dunn, Richard G. Martin

Of many physical parameters critical to design of grinding processes, impact of grinding media is among the most difficult to measure or predict. Yet impact of falling grinding balls, pebbles, or rods accomplishes the fine grinding essential to metallurgical recovery of most important minerals. Unfortunately, the same impacts that break ore fragments deform or crack grinding mill liners. A project was undertaken at Climax Molybdenum Company to measure impact forces in operating ball mills so that they might be used to calculate stresses in liner materials and be correlated with service performance of mill liner alloys. Towards that end, a method of measuring impact forces on ball mill liners using an instrumented grinding ball has been developed. Preliminary tests show that impact forces and contact stresses imposed on bare mill liners are quite high but are greatly reduced by cushioning when coarse ore particles are crushed between balls and liners. Compressive and shear stresses induced in liners not protected by coarse ore are so severe that deformation or minute subsurface cracking are inevitable in all but the small production grinding mills, regardless of mill liner alloy strength or hardness.

Jan 1, 1979