Search Documents

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By W. C. Schroeder, A. A. Berk

Practical experience has shown that at elevated temperatures solutions containing sodium hydroxide may attack stressed steel in a manner that cannot be explained in terms of ordinary corrosion. Because the ductility of the metal has been greatly reduced during the reaction, the entire phenomenon is usually called "embrittlement." Thus, after several years of operation caustic evaporators have been so badly embrittled that rivets could be cracked off with the blow of a hammer. Since fine intergranular cracks are almost always present in the zone of fracture, it has often been assumed that a process of selective corrosion in grain boundaries was responsible for the failure, although this has not been clearly proved experimentally. Concentrations of sodium hydroxide below those necessary for the uniform, rapid attack of the steel surface are reported to be most effective in producing embrittlement2, 3. In the operation of steam boilers a similar type of failure has been found, mainly in riveted seams or other capillary spaces where the solution may concentrate and where high stresses may also exist. It is believed that in such localized areas the dissolved solids may reach a value many times the few hundred parts per million prevalent in the body of the boiler. While this type of boiler failure has been the subject of investigation for a period of 20 years1, an understanding of its mechanism and a rational basis for complete protection have not yet been secured. To procure this information the present investigation was

Jan 1, 1936

By A. A. Berk, W. C. Schroeder

Practical experience has shown that at elevated temperatures solutions containing sodium hydroxide may attack stressed steel in a manner that cannot be explained in terms of ordinary corrosion. Because the ductility of the metal has been greatly reduced during the reaction, the entire phenomenon is usually called "embrittlement." Thus, after several years of operation caustic evaporators have been so badly embrittled that rivets could be cracked off with the blow of a hammer. Since fine intergranular cracks are almost always present in the zone of fracture, it has often been assumed that a process of selective corrosion in grain boundaries was responsible for the failure, although this has not been clearly proved experimentally. Concentrations of sodium hydroxide below those necessary for the uniform, rapid attack of the steel surface are reported to be most effective in producing embrittlement2, 3. In the operation of steam boilers a similar type of failure has been found, mainly in riveted seams or other capillary spaces where the solution may concentrate and where high stresses may also exist. It is believed that in such localized areas the dissolved solids may reach a value many times the few hundred parts per million prevalent in the body of the boiler. While this type of boiler failure has been the subject of investigation for a period of 20 years1, an understanding of its mechanism and a rational basis for complete protection have not yet been secured. To procure this information the present investigation was

Jan 1, 1936

By Eugene McAuliffe

IT is not possible to include in this paper, limited as it is in scope, the many diverse steps toward the reduction of mine accidents that are taken in the mines that produce the nation's coal. Every coal-producing state has enacted laws covering proper mining practices, and the major portion of these are directly related to the safety of the mine employees. The United States Bureau of Mines, the American Institute of Mining and Metallurgical Engineers, The American Mining Congress, a number of national, regional and state organizations, as well as the coal technical press, have covered time and time again all of the "do" and "don't" phases of mine operation that bear on the important question of mine and employee safety. Within the past 15 years The Union Pacific Coal Co. has attempted to put into practice in its mines in southern Wyoming these many good recommendations, finding some value in all, and yet, to secure substantial results, the management found it necessary to resort in the end to what might be referred to as "extra-territorial" methods. It is the writer's purpose to show in this paper that marked and even extraordinary betterment can be brought about when employer and employee work together with due sincerity. In presenting our own experi-ence, one that has been duplicated in so far as results are concerned on numerous other properties, no theory of perfection of management exists; on the other hand, our organization feels that as long as our record of accidents remains as shown by even our latest and best performance we still have far to go. Safety work in some form has been carried on in and about the mining properties of The Union Pacific Coal Co. since the first mine was opened at the now long-abandoned town of Carbon, Wyo., in 1868. On June 30, 1903, an explosion and subsequent mine fire occurred in mine No. 1 at Hanna, taking 169 lives, and a second explosion occurred in tile same mine on March 28, 1908, in which 59 additional lives were lost. Looking back with impartiality on the causes leading up to these two unfortunate disasters, we can only conclude that shooting from the solid, the absence of adequate ventilation, rock dusting, the use of water at the face to allay

Jan 1, 1938

By John McCoy, Edward Thimons, Kenneth Heller

As the working levels in domestic mines are developed to greater depths and work areas move further from the shafts, maintaining a safe and healthful working environment becomes more difficult. Increased temperature and humidity at greater depths becomes first a factor in productivity and then a threat to the miner's safety. Initially, a miner might develop listlessness leading to reduced productivity and reduced alertness. Continued overexertion can lead to heat stroke and possibly death. Mine ventilation engineers, therefore, must not only provide clean air to work areas, but also must provide cooled air. The following article describes the United States Bureau of Mines (USBM) and Foster-Miller's successful development of a high performance, low maintenance direct water to air contact heat exchanger for mine cooling. While heat problems frequently do not develop until mining operations descend below sea level, problems will arise any time mining penetrates high temperature rock. Hot fissure water will increase the severity of the situation, causing increases in wet bulb temperature - the temperature to which perspiring miners reject metabolic body heat. All energy expended in mining adds to the heat load which must be absorbed by the ventilation air. Just when the cooling capacity of ventilation air is needed most, adiabatic compression (autocompression) of air descending the shaft raises air temperatures 1.3g°C (2.5'F) to 2.94"C (5.3OF)/305m (1000 ft) depending on humidity. Increased temperatures decrease the ability of the air to absorb heat from the mine, and work area temperatures rise. Once forced ventilation air can no longer maintain safe work area temperatures, refrigeration methods must be employed. Many mines now use cooling coils for this purpose. A cooling coil uses refrigerated mine water to cool the air by passing the air through banks of copper tubing filled with cold water. Heat from the air is transferred to the water through the pipe with the aid of fins. Conventional water to air heat exchangers prove troublesome for many mines be- cause of the high levels of dust that are encountered, causing these exchangers to operate at relatively low efficiencies. A more satisfactory approach to work- place cooling is desired - one that offers reduced maintenance and increased cooling efficiency.

Jan 1, 1982

By S. C. Langdon, Henry S. Rawdon

The following note describing the behavior of copper under rather unusual conditions is offered for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning, as well as softening it. It is well known that metals may be rendered very brittle by electrolytic action in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear 2 similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. TO demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 801" C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for several minutes. When removed from the bath, cooled, and tested for brittleness by bending the specimen back and forth, while clamped firmly at one end in a vise, the copper rod was found to be very brittle, as compared with a rod of the same length of the untreated copper tested

Jan 1, 1921

By Lombard Squires, W. K. Lewis, W. I. Thompson

Clays consist predominantly of hydrated silicates of alumina. The formula is frequently assumed to be A1203 . 2Si02 . 2H20,'and certain of I. North Carolina. Low plasticity. 11. Same as I, after washing. Low plasticity. III. Tennessee. Good plasticity. IV. Pennsylvania flint fireclay. Low plasticity. V. Laredo, Texas. Very plastic. CaO/Na2O corrected for GO2. VI. San Antonio, Texas. Fine grained, highly plastic. Moisture and CO2 were determined together at 18.8 per cent. VII. Selected crude bentonite, California. " Data from R. Ries: Clays. John Wiley & Sons, New York, 1927. them undoubtedly have substantially this composition, but in general the ratio of silica to alumina is considerably higher. However, they always contain water of chemical constitution, as shown by Table 1.

Jan 1, 1935

By R. A. Deju, R. B. Bhappu

The theory of electrophoresis is briefly outlined and an apparatus which may be used for electrophoretic studies is explained. The results obtained using this apparatus are in agreement with those obtained by other investigators. How to solve some of the complications which occur in the measurement of zero charge and zeta potential is explained. It is believed that the apparatus described in this paper will allow rapid measurements of zeta potential, zero point of charge, electrophoretic mobility and zeta coefficient. For many years the phenomenon of electrophoresis has been studied, and much work has been done in designing an apparatus for better measurements of mobility, zeta potential and zero charge of minerals. Up to the present, most electrophoresis experiments have involved cumbersome equipment and tedious microscopic observation. The modified cell proposed in this paper obviates these drawbacks by using a Rayoscope together with a special system of lenses and filters. It therefore allows a faster and more accurate measurement of zero charge and particle velocity. THEORY Most authors currently regard zeta potential as the potential difference in an otherwise uniform medium between a point some large distance from the surface of the mineral and a point on the plane of shear. Fuerstenau,1 Miaw,2 and Gaudin and sun3 have performed some calculations of zeta potential using Henry's equation.4 Their results show wide discrepancies, probably due to differences in the past histories of the minerals used. The authors have also noticed this difference on determining the zero point of charge of quartz as shown on Table I.

Jan 1, 1967

By R. J. Allio, C. H. Randall

An automatic system for the quantitative analysis of microstrulcture has been developed. The method is based upon a statistical model of microstructure and employs phase intercept fractions as fundamental random variables. Structure-sensitive properties can be related explicitly to parameters derived from the distribution of phase intercept fractions in a matevial. THE properties of mechanical dispersions and of multiphase alloys art: intimately related to the amount, distribution, and intrinsic properties of the dispersed material. In many instances, the amount and distribution of the dispersed substances have greater influence on the over-all system properties than do the properties of the dispersed substance-Such properties as average particle size, particle size distribution, homogeneity of dispersion, volume per cent of dispersed phase, and mean free path between dispersed particles thus become critical in any evaluation of the properties of a dispersion. Unfortunately, techniques for evaluating quantitatively the microstructural characteristics of dis~ersions rapidly and accurately have not been available. If necessary, qualitative or semiquantitative devices can be utilized. Some such devices are based merely upon comparison of the specimens in question with arbitrary standards. Other techniques involve superposition of grids and tabulation of particles observed in different portions of the grid. Still other methods based upon lineal analysis entail counting lines or points at random upon the specimen to be examined; the number of intersections of the line with a given phase, the proportion of line or number of points which are covered by given phase are variously recorded. The mathematical basis for most of the techniques of quantitative metallography have been amply reviewed in the literature.'l2 without exctption, however, the standard techniques for quantitative metallography are either imprecise or are exceedingly tedious to apply. For example, tranverse integrating stage for rapid manual areal fraction measurement has been designed by Smith.3 Howerer, as in the case of any device based upon visual eslimation, operator bias may cause appreciable error. Various flying spot devices, on the other hand register particle size distributions in 2-dimensions, from which it is difficult to derive other properties of the dispersion. Thus, e.g., the 3-dimensional distribution cannot be inferred unless certain rather broad assumptions are made concerning the randomness of distribution and geometrical configuration of dispersed phase. Many limitations to the application of quantitative structural analysis can be overcome by the use of the microdensitometer, which is essentially an automated areal analysis device. Data obtained in the form of a distribution of phase intercept values are

Jan 1, 1962

By Alfred Brooks

Introduction PETROLEUM seepages are known in Alaska at four localities, all on Pacific seaboard. These, named from east to west, are Yakataga, Katalla on Controller Bay, Iniskin Bay on Cook Inlet, and Cold Bay on the Alaska Peninsula. Besides these, a petroleum residue has been found near Smith Bay on the north Arctic coast of the Territory. At Katalla, Cold Bay, and Iniskin Bay there has been some drilling for oil, and in the first field several productive wells have been opened up. Alaskan petroleum so far as its composition is known, is a refining oil, with paraffin base and low sulphur content. Most of what is known of the geology of Alaska oil fields is based on the investigations of Dr. George C. Martin, of the United States Geological Survey. A. G. Maddren, of the same service, has recently made a reconnaissance of the Yakataga oil field. The data to be here presented are chiefly taken from the following publications: G. C. Martin: The Petroleum Fields of the. Pacific Coast of Alaska, with an account of the Bering River coal deposits, Bulletin No. 250, U. S. Geological Survey, pp. 9 to 27 (1905). G. C. Martin: Geology and Mineral Resources of the Controller Bay Region, Alaska, Bulletin No. 335, U. S. Geological Survey, pp. 112 to 130 (1908). G. C. Martin and F. J. Katz: A Geologic Reconnaissance of the Iliamna Region, Alaska, Bulletin No. 485, U. S. Geological. Survey, pp. 126 to 130 (1912). A. G. Maddren: Mineral Deposits of the Yakataga District, Bulletin No. 592,. U. S. Geological Survey, pp. 143 to 147 (1914).

Jan 2, 1915

By J. B. Shannon, J. D. Grenia

The Buick Mine is a joint venture of American Metals Climax, Inc. and Homestake Mining Company located 120 miles by road southwest of St. Louis, near the village of Boss, in the `New Missouri Lead Belt'. Since start-up in 1969, over four million tons of lead-zinc ore have been mined and milled at Buick. Situated 1100 ft below the surface at an elevation 270 ft above sea level, the flat lying sinuous orebodies are up to 250 ft wide, 85 ft high and several thousand feet long. Mineralization is galena, sphalerite and chalcopyrite in dolomite.

Jan 7, 1973

The use of the verb in this mood is not as common as formerly: at the time, for example, when the Bible was translated and the plays of Shakespeare were written. Nevertheless it is an essential part of literary English. In editing the 'Mining and Scientific Press' I do not insist upon the use of the subjunctive in articles that are contributed from the outside, but it is deemed proper in all our editorial writing. To speak plainly, the subjunctive is a mark of scholarship; it is ignored by those that are not particular in such matters, and unfortunately it is a source of perplexity to many that are entirely unfamiliar with the use of it. Therefore, as an editor, I think it well to allow the indicative mood to be used by contributors in sentences in which, to be strictly correct, the verbs should be in the subjunctive mood. The fact that most subjunctives are indistinguishable in form from indicatives is another cause of trouble to the uninitiated.* For example, the verbs in such phrases as "Suffice it to say", '(So help me God ", and "God save the King" are in the subjunctive. One reason why the subjunctive is becoming uncommon is the growing habit of expressing the subjunctive meaning by aid of auxiliary verbs that are coupled with the infinitive; thus: "It will sate to say" and "May God save the King". The subjunctive is common in subordinate clauses, and that is how it obtained its name, 'subjunctive', meaning

Jan 1, 1931

By J. D. Edwards, C. S. Taylor, A. S. Russell

Solubilities and densities are reported for alumina hydrates in NaOH solutions under the conditions of the Bayer process employed to purify alumina for aluminum production. The equilibrium constants for reactions to form A102- accurately correlate the effects of NaOH concentration on the solubilities; the temperature coefficients of the equilibria lead to heats of solution of 7.34, 4.76, and 5.24 kcal for the a trihydrate, a monohydrate, and ß trihydrate, respectively. Moderate calcination does not change the solubility of the a trihydrate but increases that of the a monohydrate. At solution temperatures above 100°C, the trihydrates transform rapidly to a monohydrate. Hydro-thermally produced a monohydrate is the stable phase above 20°C. CORNERSTONE of the aluminum industry, the Bayer process for alumina production is based on the difference in solubility of hydrated alumina in NaOH solutions between 170" and 40°C. Solubilities and densities in this system were determined thirty years ago by M. Tosterudl under the direction of J. D. Edwards and C. S. Taylor. The solubility data, which still appear more concordant than those in the literature, are employed to sort out the complex equilibria in this system. The nomenclature for the alumina hydrates is that presented in The Aluminum Industry' and more recently summarized in Alumina Properties.3 a trihydrate is the purified phase analogous to gibbsite, a monohydrate is similarly akin to boehmite, and ß trihydrate is sometimes known as bayerite. Literature Goudriaan4 reviewed the early literature on alumina in NaOH solutions and presented data on the solubility at 30°C of several forms. The gel precipitated from aluminum sulphate or chloride with ammonia and dried at 130" to 140°C had the highest solubility but was unstable, its solubility being cut to one-tenth on standing in NaOH. The solubility of the gel was decreased one-third on calcination at 300" to 400°C, while that of the gel transformed in NaOH at room temperature to a crystalline trihydrate was unchanged on calcination. The preparation produced by slow hydrolysis of sodium aluminate solution with CO, in the air gave solubilities in rough agreement with later values for a trihydrate. The solubility of this form was increased slightly by the calcination. Fricke and Jucaitis5 extended the work to 30" and 60°C with a trihydrate. They also gave solubilities for ß trihydrate (bayerite b), although the residue belonging to the left branch of the solubility curve corresponded to a trihydrate. The residues at high NaOH concentrations were mono and trisodium aluminates, the latter being 3Na2O . AL2O3 • 6H2O. Solubilities of a trihydrate at 95°C and of a monohydrate at 150" and 200 °C come from the work of Magarchak.6 a trihydrate transformed to a monohydrate above 95°C. A few measurements on the solubility at 25°C of an alumina trihydrate prepared by slow hydrolysis of NaAIO, solutions were presented by Sprauer and pearce.? Their analyses showed the monosodium aluminate to have the composition Na2O.Al2O3-2.5H2O.

Jan 1, 1956

By J. H. Henderson, J. Naar

The displacement of a wetting fluid from a porous medium by a non-wetting fluid (drainage) is now reasonably well understood. A complete explanation has yet to be found for the analogous case of a wetting fluid being spontaneously imbibed and the non-wetting phase displaced (imbibition). During the displacement of oil or gas by water in a water-wet sand, the porous medium ordinarily imbibes water. The amount of oil recovered, the cost of recovery and the production history seem then to be controlled mainly by pore geometry. The influence of pore geometry is reflected in drainage and imbibition capillary-pressure curves and relative permeability curves. Relative permeability curves for a particular consolidated sand show that at any given saturation the permeability to oil during imbibition is smaller than during drainage. ' Low imbibition permeabilities suggest that the non-wetting phase, oil or gas, is gradually trapped by the advancing water. This paper describes a mathematical image (model) of consolidated porous rock based on the concept of the trapping of the non-wetting phase during the imbibition process. The following items have been derived from the model. 1. A direct relation between the relative permeability characteristics during imbibition and those observed during drainage. 2. A theoretical limit for the fractional amount of oil or gas recoverable by imbibition. 3. An expression for the resistivity index which can be used in connection with the formula for wetting-phase relative permeability to check the consistency of the model. 4. The Iimits of flow performance for a given rock dictated by complete wetting by either oil or water. 5. The factors controlling oil recovery by imbibition in the presence of free gas. The complexity of a porous medium is such that drastic simplifications must be introduced to obtain a model amenable to mathematical treatment. Many parameters have been introduced by others in Iprogressing" from the parallel-capillary model to the randomly interconnected capillary models independently proposed by Wyllie and Gardner3 and Marshall4. To these a further complication must be added since an imbibition model must trap part of the non-wetting phase during imbibition of the wetting phase. Like so many of the previously introduced complications, this fluid-block was introduced to make the model performance fit the observed imbibition flow behavior. THE IMBIBITION MODEL ASSUMPTIONS The following assumptions are common to many two-phase models previously described. 1. The wetting characteristics of the medium are clearly defined. 2. When two fluids co-exist in the medium, the wetting phase will fill the smaller pores and the non-wetting fluid the bigger ones. 3. The pores have a circular cross section. 4. Apparent pore radii are related to the capillary pressure (drainage) by

By E. L. Estabrook

THE production of crude oil in Wyoming rose to 44,290,010 bbl. in 1923 and declined, during 1924, to 39,295,030 bbl., a decrease of about 11 per cent. The Salt Creek field supplies 75 to 80 per cent. of the production. Pipeline runs from the Salt Creek field reached a maximum in November, 1923, at a daily average for the month of 116,437 barrels. During 1924, the gas pressure in Salt Creek has declined rapidly and the production dropped to about 60,000 bbl. per day. Part of 'the decline during the last few months was due to lack of power to pump the wells. The electric-power plant of the Midwest Refining Co. did not begin to deliver current until the middle of December, by which time several hundred wells were off production. The cold snap in December, which brought, the temperature down to 30° below zero on the 17th, tied up operations almost completely and the average production for the month was only 49,545 barrels. As more wells are being pumped and the number of dead wells reduced, the production is rising and was up to 61,000 bbl. during the last week of January. A further increase is expected as the weather becomes warmer. The production of Salt Creek, by months, during 1924 is given in Table 1. TABLE 1.-Total Monthly Production, Average Daily Production and Number of Producing Wells in Salt Creek during 1924 TOTAL PRODUCTION, DAILY AVERAGE, NUMBER OF MONTH BARRELS BARRELS WELLS January 3,523,647.40 113,666.05 919 February 3,074,916.67 106,031.61 929 March 2,977,095.14 96,035.32 950 April 2,811,110.22 93,703.67 987 May 2,858,842.04 92,220.71 1,024 June 2,649,752.57 88,325,09 1,092 July : 2,697,829.36 87,026.75 1,153 August 2,624,371.84 84,657.15 1,213 September 2,281,219.04 76,040.64 1,274 October 2,073,961.42 67,000.84 1,313 November 1,722,050.09 57,401.67 ~ 1,335 December 1,535,903.78 49,545.28 1,352 Total 30,831,699.57 84,239.61 1,352

Jan 3, 1925

By H. G. Kok

The continuous increase in energy costs has made it necessary to consider a broader use of belt conveyors for the transportation of material from the mine pit to the processing plant. Hard rock has to be crushed before it can be moved by belt conveyors. Systems are in the planning stage for mining hard rock, such as copper and iron ore, by using high-capacity, mobile, or semi-portable crushers. The mobile crusher is located in the pit, and the crushed material is transported by energy-efficient, shiftable belt conveyors out of the pit.

Jan 1, 1983

By J. M. Oblak, R. F. Hehemann, R. H. Goodenow

STUDIES of surface relief and growth kinetics have lead to the concept that widmanstatten ferrite along with upper and lower bainite constitute a continuous series of decomposition products.1-4 Current models4 propose that these products form as plates with a coherent or semicoherent leading edge which propagates at a rate controlled by diffusion of carbon into the surrounding austenite. There are, however, important crystallographic and morphological differences between these products—particularly between upper and lower bainite. For example, upper bainite appears to exhibit a (11lIy orientation habit, whereas lower bainite develops with a more irrational habit near {2251y.5-7 Many of the morphological features of these decomposition products are not yet well-documented. Recent studiess have demonstrated that low-carbon martensites form as sheets of closely spaced needles on {lllly planes while higher-carbon martensites form as plates with {225}? or other orientation habits. The similarity in the crystallography of these two modifications of martensite with upper and lower bainite is striking. Therefore, a study of the morphology of bainite in a series of hypoeutec-toid alloy steels has been initiated to explore these relationships further. The question of immediate interest is whether upper and lower bainite form as plates or needles. A two-surface (approximately perpendicular) metallographic method was employed to study the morphology of bainite in a variety of low and medium alloy steels. Compositions of these steels have been reported elewhere. The behavior of 4340 and 4370 was typical and will be described here. Austenitizing treatments involved 20 min at 2350°F for 4340 and at 2000°F for 4370. Isothermal transformation was conducted in molten-salt baths. Upper bainite was produced at 925°F in the 4340 steel and lower bainite at 575°F in 4370 with transformation times adjusted to produce 10 to 15 pct of the decomposition product. Many of the morphological features of upper bainite have been catalogued in the recent literature.'' The two principal variants observed in the present investigation are illustrated in Fig. l(a). One form appears as long, thin plates or needles and the other as small, frequently irregularly shaped particles. Both variants may occur as isolated forms but more frequently appear in groups as demonstrated in Fig. l(a). Two-surface analysis reveals that these two variants constitute different sections through a single morphological form. To demonstrate this, a number of sections perpendicular to the plane of Fig. l(a) were prepared at various positions along the length of the elongated particles. A section taken at position 1 in Fig. l(a) is presented in Fig. l(b). Here, the dark line represents the edge of the sample and the left-hand portion of this photomicrograph is that from the surface perpendicular to the original plane of polish. Since it was necessary to repolish the original surface after each sectioning, the shape of the bainite particles on this surface, right hand side of Fig. l(b), changes with each sectioning. The disappearance of plate A, Fig. l(a), in Fig. l(b) emphasizes the small cross section of these structures. The group of particles in the lower left-hand

Jan 1, 1964

By John Wulff, Robert Kamm, M. A. Steinberg

IN a previous paper1 from this laboratory, the development of a lead grid method for exploring the distribution of strain and density within metal powder compacts was described, In that work thin lead foil with rectangular holes cut at regular intervals was inserted with the powder fill, the arrangement pressed and then radiographed to permit measurement of the deformation of the lead grid. Densities at each grid element obtained in this manner were plotted as a function of the die dimensions. From such plots it was, found that the densest part of a compact pressed from one side (the top) is at the top outer region and the least dense at the bottom outer region -of the specimen. The axial density maximum occurs more often nearer the bottom than at the top. As a result of such exploratory measurements, it appeared reasonable to conclude that variations in density could be attributed in the main to die wall friction. Thus compacts of large diameter appeared relatively uniform in density except where the die fill had been uneven. Finally it was found that lubrication of the finely finished die cavity contributed more to magnitude and uniformity of density within the compact than interparticle lubrication. Since publication of the above results, it was found that circular-hole grids could be more accurately made and, when deformed within the powder, more readily measured and analyzed. Much of the former work was repeated and new results which include the effect of lubrication, compact height, pressure, speed of pressing and vacuum pressing are reported in the present paper. CIRCULAR-HOLE GRIDS AND ANALYSES OF RADIOGRAPHS Commercial lead sheet 0.008 in. in thickness was used in all the work reported. The 0.0938-in. diam holes were punched in the sheet on 1/8-in, centers to an accuracy of 0.001 in. The finished grid used contained eight or more holes in a row and from I to 24 rows. The lead sheet was clamped between two pairs of brass strips bolted to a small milling machine table which was itself bolted to a bench in correct position near a vise which held the punch. Travel of the lead grid in two dimensions was controlled by two steel lead screws calibrated in 0.001-in. divisions. A stripper plate was used on the punch to avoid distortion of the lead foil. A high carbon-high chromium (chrocar) one-piece steel die was used throughout the work. The die cavity was 1,125 in. in diam and the clearance between plungers and die wall was 0.001 in, The die was also used for pressing from both ends with two long plungers. Finally, lapping of die and plungers gave a surface whose rms value on an Abbot profilometer was 5 micro-in. The die walls and plungers were, except where otherwise noted, lubricated with a stearic acid suspension in benzene. This was put on in multiple layers and allowed to dry before filling the die.

Jan 1, 1948

By Robert A. Cummings, Francis S. Kendorski

The behavior of the rock mass during block caving affects the production of the mine and dictates the loads and deformations placed on required drifts. Traditionally, the drifts used are massively reinforced and buttressed against very high and erratic mining- induced abutment loads or swell muck loads, resulting from undercut- ting. Extensive field investigations in numerous block caving mines in the porphyry intrusive environment, coupled with models developed for tunneling and longwall coal mining, have allowed the development of a unified hypothesis for ore bodies of various degrees of competence. In general, the hypothesis incorporates several sequential steps in the driftlrock mass deformation history, each with characteristic magnitudes, duration, and areal extents depending on ore body competence. 1. Prior to initiating caving, but subsequent to drift development, the rock mass and drift are in a state of near-equilibrium. Zones of stress concentration have stabilized, as for a tunnel. 2. For a newly undercut panel, the rock mass and drifts directly beneath the undercut respond by dilating towards the void created, and undergo a release of compressive strain that manifests itself as tensile failures. 3. For adjacent areas, the rock mass is compressed as the load is shed from the undercut level.

Jan 1, 1983