Search Documents

By J. E. Cannaday, R. J. Austin, R. K. Saxer

PREVIOUS investigators have determined activation energies and have postulated various controlling mechanisms for creep.'-' Recently Barrett et 01.I5 have suggested, as the result of their work with cadmium, that the apparent activation energies for creep (AHc) above 0.5 T, could be correlated by means of activation energies for self-diffusion (AHSD) and modulus of elasticity functions: AHC = AHSD - (5RT/E) dE/dT. The wide disparity of apparent activation energies previously obtained with nickel compared to those reported for other fcc metals and the desire to test the postulate of Barrett el al. prompted this study. The as-received 17.5-mil nickel wire used during this work assayed 99.87 pct pure, Table I. X-ray analysis indicated that the wire was in a stress-re- lieved state and metallographic examination revealed an equiaxed grain size of approximately 0.01 mm. Specimens degreased in acetone and cut to 1-1/2 in. lengths were tested in a cam-mechanized constant-stress creep machine. A vacuum of at least lo-5 mm Hg was maintained during all tests. Stresses were applied when thermal equilibrium was established. When a measurable (at least 0.5 pct) secondary creep was observed, the temperature was pulsed to a higher temperature. Pulsing time varied from 30 sec at 480°C to 2 min at 1300'C and above. Slopes of creep curves were determined after the initial acceleration in the strain rate had subsided and steady-state creep was achieved. To confirm the results obtained, additional tests were performed incorporating a temperature pulsing method suggested by sherby. In this method the load was removed during temperature pulsing and reapplied after thermal expansion had occurred. No appreciable differences in results were obtained. Tests were performed over a wide range of temperature (470" to 1310°C) and stresses (250 to 17,000 psi). The expression was used to calculate activation energies. In this expression T1 and T2 are the initial and final temperatures, and el and i2 are the creep rates at T, and T2. The variation of the apparent activation energies with the mean test temperature calculated by means of Eq. [I] are shown in Fig. 1. The mean test temperature (Tmean) was calculated from the relationship

Jan 1, 1967

W. O. OWEN,* Washington, D. C. (written discussion?). Few people appear to realize that the time to reach the crippled soldier is when he is first hurt. In my own judgment, the best time to reach him is before he is hurt, by showing him what other cripples have themselves clone of their own initiative, without Government-support, rendering themselves self-supporting, able to bear a little bit more than their own weight, so that they may lay aside a little bit for a rainy clay and some for a little fun in

Jan 5, 1918

By Roger B. Alke

INTRODUCTION Request to Mine Beneath Bridge The Jakes Run Bridge is a reinforced Portland concrete arch filled bridge located on WV Route 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Fig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old having been built in 1929 and is owned by the Department (WV Department of Highways). [ ]

Jan 1, 1984

By H. R. Reed

THE cost of hoisting with electricity in deep mines is a matter about which little information has been published. This paper makes a detailed study of such costs and presents the information in a series of curves. In particular the curves show the cost of hoisting ore from depths varying from 500 to 7000 ft. Vertical with the shaft at 70° incline for the double cylindroconical and double cylindrical drums, the hoists operating balanced, using Ward Leonard and Ilgner-Ward Leonard control, and designed for most economical operation from each depth. Operation with the double cylindrical drum is expanded to cover hoisting from 2000 to 5000 ft. using equipment designed for 5000 ft. and from 4000 to 7000 ft. using equipment designed for, 7000 ft. Additional curves are included to show the ratings of the necessary hoist motors, energy input per hoisting cycle and size of flywheel in tons for complete equalization when the Ilgner-Ward Leonard system is used, also hoisting efficiency. The duty imposed on a mine-hoist motor fluctuates between wide limits during a cycle of operation. The demand on the motor may vary from a large horsepower value' near the beginning of the cycle to a small or a negative demand near the end of the cycle. Such factors as tonnage to be raised per hour, depth of shaft, and balanced or unbalanced opera-tion have such a marked effect on the operating cycle and vary to such an extent for different mines that no set of rules can he formulated for quickly determining the size of the motor required. The duty cycle from which the motor rating is (derived must he determined for each case according to the conditions of the proposed hoisting operations. The motor torque required at the cardinal points of the duty cycle is determined from the moment or torque in pound-feet necessary to raise and lower the load and ropes, accelerate and retard the load, ropes, drum, etc. The torque diagram depends largely upon the type of drum. Two different types of drums, if used on exactly the same duty cycles, may have widely different peak demands and capacities of hoist motors. The essential feature in the design of hoisting drums and in determining

Jan 1, 1937

By Edward C. J. Urban

ESSENTIAL requirements for ensuring safe working atmospheres in underground metal mines are planned systems of ventilation and provision for effective distribution of sufficient volumes of air by auxiliary equipment. Investigators1 in the past have suggested that quantities of air supply ranging from 300 to 800 cu. ft. of air per minute per man underground are necessary, to establish adequate general ventilation. These fundamentals are just as important as the use of water in dust suppression, control of blasting, the use of personal protective equipment, frequent inspection of working areas and education of employees in good dust-prevention practice. During the past two years the necessity for direct control of the underground working environment has become particularly urgent. The increase in production rate, with two-shift and three-shift operation replacing the single shift, has complicated the problem of dealing with excessive concentrations of blasting fumes and gases, carbon dioxide and monoxide, heat and oxygen deficiency. Although previous industrial hygiene programs had given consideration to these factors, they were generally regarded by mine operators as secondary to the control of dust hazards. Today, blasting smoke in a mining area means delayed production because the miner cannot return to his work place after a short interval. Smoke on the haulage level means a safety hazard and exposure of the underground employees to excessive concentrations of atmospheric contaminants. Exposure to the moderately excessive concentrations of carbon dioxide and monoxide found in metal mines has caused physiological disturbances and a decreased capacity for work; deficiency of oxygen, in some cases to as low as 3 per cent, has resulted in fatalities. During the past 10 years the Saranac Laboratory2 has been associated with the iron mines in the Upper Peninsula of Michigan and Wisconsin in developing and maintaining an industrial hygiene and silicosis-prevention program. At present, about 35 underground iron-ore mines are operated full time in this area. With two exceptions, all of them are ventilated by main fan installations installed either on surface or underground. ,The types of mining used in these mines may be classified either as sublevel cave, radial top slice or sublevel stope, and the procedures commonly employed in the ventilation of these three types are described in Figs. 1 and 2. A number of different methods of mine ventilation had been in use in this area when the study was started. Natural ventilation had proved unsatisfactory. The wide variation between low air volumes during the summer months and higher volumes during winter led to unpredictable conditions that were difficult to control. In the majority of the mines two separate shafts or openings to surface are utilized in

Jan 1, 1943

By Walter von der Linden

INTRODUCTION There are three essential components for a modern longwall mining system: the coal cutting/loading machine, the self-advancing supports and the longwall conveying system. The latter consists of a face conveyor, a stageloader and a belt tall section arrangement (Figure 1). The longwall face conveyor is an integral component of the face equipment and has a threefold purpose: 1) continuous coal haulage. 2) track for cutter/loader . 3) reference/anchor rail for roof support advance. Further requirements for the longwall conveyor are horizontal flexibility for conveyor advance without interruption of haulage and cutter/loader tramming and vertical flexibility to cope with seam undulations.

Jan 1, 1981

By C. H. North, L. E. Lynd, W. W. Anderson, H. Sigurdson

CONSIDERABLE uncertainty is revealed in the literature regarding the nature of the titanium minerals which make up the bulk of the heavy, opaque fractions of numerous beach sand deposits of the world. An investigation was made, therefore, of beach sand concentrates of North Carolina, Florida, Brazil, and India. Magnetic concentration, X-ray, and microscope data were obtained which show that these concentrates consist essentially of ilmenite and its alteration products. The alteration, brought about by oxidation and leaching of iron values, has resulted in upgrading the ores to a range of 56 to 64 pct TiO2, as compared with 52.7 pct in ilmenite of theoretical composition. Conclusions drawn regarding the nature of the dominant titanium-bearing mineral in beach sand deposits have been based mainly on chemical composition, specific gravity, and petrography. This material has usually been referred to as ilmenite or weathered ilmenite. It has also been referred to as arizonite because in chemical composition it resembles an occurrence in Arizona which was described by Palmer1 in 1909.

Jan 8, 1954

By C. R. Barrett, N. N. Singh Deo

The high-temperature steady-state creep behavior of a series of dilute copper-silicon alloys was studied to determine the effect of stacking fault energy on the creep-rate. The steady-state creep rate is, when taken at equivalent diffusivities decreases with decreasing stacking fault energy. The stress and temperature dependencies of is suggest that creep is a difusion controlled dislocation climb process. Electron microscopy studies of the creep substructure revealed: 1) the subgrain size is not a function of the stacking fault energy in these alloys, 2) the dislocation density not attributed to the subgrain walls seems to be higher during primary creep and decreases to a lower steady value during steady-state creep, and 3) the dislocation density during steady-state creep decreases with decreasing stacking fault energy. In the past few years numerous investigators have studied the influence of stacking fault energy on high-temperature creep strength. Most of these investigators have confined their attentions to studying the relationship between steady-state creep rate, is, and stacking fault energy, ?, when samples are tested under conditions of comparable stress and temperature. For the case of fcc metals, it was initially shown by Barrett and Sherbyl and since confirmed by many others2"4 that is decreases with decreasing ?, often following an empirical relation of the form i ?m where m is a constant about equal to 3. The application of theory to explain this observation has not been entirely successful. One of the main difficulties has been the almost complete lack of structural information (dislocation density, subgrain size, and so forth) for samples with different stacking fault energies, tested under high-temperature creep conditions. weertman5 has attempted to explain the stacking fault energy dependence of is on the basis of a dislocation climb mechanism. Assuming that both the rate of dislocation core diffusion and the ease of athermal jog formation decreases as ? decreases Weertman has argued that the rate of dislocation climb and hence the creep rate should also decrease as ? decreases. One questionable aspect of Weertman's analysis is the assumption that core diffusion down extended dislocations is slower than core diffusion down unextended dislocations. The only experimental work done in this area, by Birnbaum et al.6 on nickel and Ni-60 Co, has shown the core diffusivity to increase with decreasing ?. Theories of steady-state creep based on the diffusive motion of jogged screw dislocations often seem unable to predict even the qualitative nature of the es- relationship. Assuming that Weertman is correct in his assumption that the dislocation jog density decreases with decreasing ? then the jogged screw theories predict an increasing dislocation velocity with lower ?. It is usually assumed that the increase in dislocation velocity implies a corresponding increase in creep rate. However, two other factors must be considered before such a statement can be made. That is, we must know how both the mobile dislocation density and the effective stress (the difference between applied stress and internal stress) vary with ?. Significant changes in either one of these factors could outweigh any change in dislocation velocity accompanying a change in ?. And with the slower rates of recovery expected in low stacking fault energy materials it seems likely to expect both mobile dislocation density and effective stress to be dependent on ?. Sherby and Burke7 have suggested that stacking fault energy influences the creep rate in an indirect way. These authors cite evidence that the steady-state subgrain size generated during high-temperature creep is a function of ? decreasing with decreasing ?. Assuming the creep rate to be proportional to the area swept out by each expanding dislocation loop and that subgrain boundaries are good barriers to dislocations, then the creep rate should be proportional to subgrain area, hence increasing as ? increases. A critical evaluation of any of the above theories requires more quantitative information concerning the dislocation substructure generated during high-temperature creep. Accordingly this investigation was undertaken with an aim of studying the influence of stacking fault energy on tbe steady-state creep characteristics of a series of dilute copper-silicon alloys. Special emphasis was placed on studying the strain dependence of both the dislocation configuration and density. MATERIALS AND PROCEDURE Dilute copper-silicon alloys of the compositions shown in Table I were tested in tension at constant stress. The relative stacking fault energy of these alloys has been determined and is shown in Table 11. An Andrade-Chalmers lever arm was used to maintain constant stress and testing was carried out in a water

Jan 1, 1970

By E. A. Cisney

The formula for calculating the crystallographic angles of a tetragonal lattice is: C°S =where $ is the angle between planes (HKL) and (hkl). The angles in Table I have been calculated for indium

Jan 1, 1960

By C. A. Hansen

INTRODUCTION It has been the experience of the writer, during some. five years' work with electrolytic zinc, that the zinc cell is perhaps more- sensitive to impurities in the electrolyte than the analytical methods as yet developed for the chemical identification and determination of these impurities; but that, when proper purification methods have been applied to a given solution, the behavior of the cell is quite independent of the original sources from which the zinc sulphate has been derived. It has also appeared that the behavior of the zinc cell is the best and surest check on the correctness and thoroughness of the purification methods used, because it indicates the presence of both current impurities. and cumulative impurities derived from the leaching of the ore; it also in

Jan 3, 1918

By Ben Gumpertz

THE important factors in any study of the screening of sand with a gravel enve-lope, as applied to use in oil wells, are: (r) sand size and shape, (2) gravel size and shape, (3) ratio of gravel size to sand size, (4) flow velocity, (5) viscosity of the fluid. Perhaps the first extensive investigation of the function of gravel in screening sand was performed by Coberly and Wagner,1 from which the following conclusion was drawn: "The diameter of the largest grains in a single classified sand suitable for gravel packing is approximately 23 times the grain size at the ten-percentile analysis of the formation sample." This applies to sands classified by Tyler screens and is for gravel grains of the maximum size that could be used to form a stable bridge. Field practice has shown that the screening effect of a given gravel for a given sand apparently varies with the flow velocity.2 Also, it has been assumed by some opera-tors that the thickness of the walls of the gravel envelope surrounding the well has little effect upon the screening process. It is thought by others that a narrow envelope of gravel might form an ineffec-tive screen. Thus the purposes of this work are: I. To investigate the effect of gravel-sand size ratio upon screening action under the condition of varying flow velocities. 2. To investigate the effect upon screen-ing action of varying the thickness of the gravel screen.

Jan 1, 1940

By Louis A. Mattson, Winthrop A. Rowe, John T. Cumberlidge, Victor M. Mejia

The parent ultramafic of Nickel Mountain is an alpine-peri-dotite. Compositional layering and late stage dunites suggest the intrusive crystallized in the upper mantle or lower crust. The ultramafic mass was fault emplaced in the upper crust, probably during upper Jurassic time. Soil, saprolite and silica boxwork nickeliferous ores were formed over the Nickel Mountain peridotite during the development and later destruction of the Klamath peneplane. A complex fault pattern was produced by irregular gravity displacements along fault surfaces during the relative uplift of Nickel Mountain. The majority of the ores occur in the fractured hanging wall of these gravity faults. Consequently, structure mapping is important for mining purposes. Ore types at Riddle are classified on the basis of MgO, Fe, and Si02 contents as well as textures. The chemical, mineralogical and textural differences of the various ore types reflect differences in weathering histories. Satellitic ore bodies occur peripherally to Nickel Mountain. These are erosional remnants of landslides and large gravity fault blocks from Nickel Mountain.

Jan 1, 1976

By Frank Clowes

This lamp has been devised to burn oil from a flat wick in the usual way for lighting-purposes ; and also to burn a hydrogen-flame of standard size instead of the oil-flame, when delicate and accurate gas-testing is to be carried out. The change from the oil-flame to the hydrogen-flame, and vice versa, can be made with great rapidity, and without opening the lamp or running any risk in the presence of gas. The oil-flame serves for illumination; and when the wick is drawn down by the " pricker," so as to abolish the light, the pale blue reduced oil-flame serves to detect fire-damp or "gas," in any propor

Jan 1, 1894

BROWN iron ore reserves of Franklin county are being proved economical by Heavy-Media separation at the Blackburn mine of the Shook & Fletcher Supply Co. about 120 miles north-west of Birmingham. The ore occurs under a cover of ferruginous chert and gravel and these materials are also disclosed as streaks in the ore body as it is mined. Previous methods of jigging and hand sorting the ore became too expensive because of rising wages but the use of Heavy-Media separation has proved economical and is making Franklin county the most promising source of additional reserves of brown ore.

Jan 12, 1950

By Frank B. Gilbreth

The problem of the crippled soldier in industry is not a problem of war work only; it is a problem of industrial development. As individuals, each one of you is seeking to provide our maimed heroes with such teaching as will render them, in the shortest possible amount of time, productive and satisfied members of the community. As individuals you are interested in the organizations that are preparing to receive these men, to train them and to place them at that work for which they are best fitted. As an organization, it is now your duty to take up the industrial end of the problem, to investigate existing conditions in the industries, to discover where the opportunities for employment lie, and so readjust industrial practice that the cripples may be utilized to their own and the community's good with the least shock to themselves or to the industries, and with the greatest amount of permanent benefit to all concerned. We have divided industrial opportunities suitable for cripples, roughly, into three classes. First, such as already exist in the industries, which can be set aside for cripples only, present occupants being transferred to other work for which they can be fitted but which is not suitable for cripple work; second, opportunities in the industrial world that, through changes in the working equipment or tools, or through appliances attached to the cripple himself, can make the cripple a competitor of the sound worker; third, opportunities not existing at present in the industries, but which could be introduced for the good of the community without placing the cripples into competition with any existing class of workers. As typical of the first type of occupations for cripples, we have mentioned that of store-keeper, of the second type that of typist,2 and of the third type that of dental nurse.3 The last occupation can be so arranged as to take from the overworked dentist the work of cleaning teeth; and

Jan 1, 1918

By Lawrence F. Schubert

Instrumentation is not a stranger to the minerals processing industry. In fact, very few plants now exist that haven't to one extent or another adapted operations to instrumentation. But with the rapid growth of such controls has come the need for effective departments composed of men trained to maintain and repair the instruments; here is where many firms fall short. The importance of the role an instrument department should play is underscored by the omnipotent effects which instruments often exert over an operation. Reserve Mining Co. is an example: while instrumentation at this taconite plant represents approximately 2% of the process equipment cost, a breakdown of instruments may result in the ineffective use (or complete shut-down) of the other 98% of plant investment.

Jan 7, 1966

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By Nick Barton

Simple methods for estimating the shear strength of rock joints and waste rock are reviewed. For the case of rock joints, the methods are based on a quantitative characterization of the joint roughness and the joint wall strength. Size-effects are found to reduce the peak strength of large joint samples to values below the ultimate or so-called "residual" values measured in the laboratory. Tilt tests and surface profiling on natural size blocks within the jointed rock mass are recommended for obtaining scale-free properties. The joint parameters obtained can be used to model complete strength-displacement-dilation behavior if this level of input is required. Large scale tilt tests can be performed with advantage on both rock joints and waste rock. The behavior of these two materials is surprisingly similar. Both are influenced by the size-effects on the compression strength of the rock, and both have similar log-linear relationships between effective normal stress and the peak drained friction angles. The resulting high values of friction near the toe or close to a slope face in either material can be misleading.

Jan 1, 1983

By T. G. Chapman

THE writer has carried on experimental work for several years with respect to the simultaneous dissolution of gold by cyanide and the adsorption of the dissolved gold on activated charcoal in ore pulps, fol-lowed by the recovery of the charcoal by flotation. The results of this experimental work have been sufficiently encour-aging to suggest a new process based on the principle of simultaneous dissolution and adsorption of gold, applicable to certain ores and tailings that cannot be treated to advantage by countercurrent decantation or filtration. Applications for patents have been filed and The Dorr Company, Inc. has the exclusive right to license the use of the process. The purpose of this paper is to describe such a process, state its pos-sible advantages and immediate field, and give some results obtained on a laboratory scale.

Jan 1, 1939