Search Documents

By Henry J. Welge

The approximate methods which are now in use for calculating oil displacement from reservoirs by gas-cycling or gravity-drainage at constant gas pressure, or by water flooding, make use of fundamental relationships derived by Leverett' and Buckley and Leverett.2 The mathematical equations needed are derived by applying Darcy's law to the flowing phases, and by material balance considerations. ln general, any treatment of this type gives. for any particular exploitation time considered, a plot of oil saturation against distance in the reser-voir. The oil recovery must then be obtained by integrating in some manner the area under the plot. A useful analytical method has been derived for computing the average saturation, and hence the oil recovery. Use of this method simplifies the calculations because it makes unnecessary any numerical integrations. and even the saturation distribution plots are not needed. A further advantage of the method is that knowledge of the relative permeabilities is required only for a limited and intermediate saturation range. In both the Buckley and Leverett method and the method discussed here, a linear sand section is assumed, and in the case of gas drive the gas pressure is assumed sufficiently constant both with respect to reservoir position and time so that changes in gas density. solubility, or reservoir volume factor are negligiklle. Thus, the exploitation contemplates oil displacement as by an immiscible phase. Examples are given to illustrate how the new method can be used. INTRODUCTION AND THEORETICAL BACKGROUND This paper treats a simplified method for computing oil recovery when the oil is displaced, from the reservoir sand by a fluid which, within the limits of accuracy desired, can be assumed to be incompressible and immiscible with the oil. The method makes use of two basic relations originally developed for the case of water displacing oil. However, the case of gas displacing oil saturated with gas at a constant (or nearly constant) pressure may also be considered a displacement by an immiscible fluid. This is possible for the reason that the concentration of the gas in the oil never changes if tile pressure is fixed. consequently, any additional free gas must remain undissolved in the oil, and so must act essentially as an immiscible phase. For convenience, the cape of gas drive will be considered first. Both of the two basic relations needed refer to a linear reservoir, or one which may be somewhat idealized so that a constant cross-section is exposed to fluid flow. Further, the displacing phase is injected at one end, or face; of the reservoir, while the produced fluids are understood to emerge at one point only. which is the opposite face of the reservoir. As indicated in Fig. 1, the reservoir may he inclined by some angle 8. The first of the required equations may be derived by applying Darcy's law to both displacing and displaced phases, and subtracting the two equations. The result for water drive has been given previously, as Equation (13) of the reference by

Jan 1, 1952

By B. Stas, L. Siska, L. Dlouhy, A. Skrabis

The basic research program of the Scientific Coal Research Institute at Ostrava - Radvanice into the problem of geophysics has been influenced by the specific nature of present urgent geo- physical problems in mines and directed to attain higher grade of effectiveness, safety, and overall economy in mining activity. The research has been divided into two basic trends: Seismoaccoustic research deals with questions pertaining to safety in mining especially when work is in coal seams under "heavy roofs", i-e., thick beds of sandstone prone to rock bumps and characterized by caving. Methods have been developed with the definite aim to determine the time and space prognosis of critical states of tension in the rock mass when stability is disturbed as a result of mining activity. Seismic research is directed towards the determination of detailed structural and tectonic elements of the internal geological formation of the Carboniferous rocks, the establishment of continuity or tectonic faulting of coal seams, and the evaluation of magnitude, shape, and time changes in the rock mass surrounding the mine workings. The measurements have been applied either from the surface or in the underground workings according to the specific nature of individual problems. Satisfactory results have been obtained in some branches of this research, other branches being still in the stage of development. Remarkable results have been achieved in the development of seismoaccoustic methods designed to establish the time prognosis of dangerous dynamic phenomena accompanying the process of strata deterioration above the worked longwall face. One of the most

Jan 1, 1971

By F. D. Rosi, C. A. Dube, B. H. Alexander

WHEN a deformed polpcrystalline metal is heated to a sufficiently high temperature, a recrystallized structure develops which consists of small, essentially stress-free grains. This transformation is referred to as primary recrystallization. Under certain conditions, on prolonged annealing of the specimens, a type of grain coarsening occurs in which a small number of grains commence to grow at various points by devouring the neighboring finegrained primary structure, which, in itself, exhibits a marked stability toward normal grain growth. This grain coarsening process has been referred to by Burgers' as "secondary recrystallization" or "exaggerated grain growth." Although much work has been done on recrystallization and growth processes, present knowledge of the factors which determine the occurrence and growth of secondary grains is inadequate for the advancement of a theory which accounts for the observed characteristics of this recrystallization phenomenon. In this respect, it would be important to make measurements of the velocity of growth of these large secondary grains. The early work of Feitnecht2 on aluminum showed that the size of secondary grains increased with temperature and time, suggesting that such measurements would be possible. More recently, Burgers1 found that the growth velocity of these grains in aluminum was constant over a large time interval, as is generally found for the growth velocity of primary grains in a uniformly deformed test piece.3-5 It is reasonable to expect that the determination of the activation energy of the secondary growth process might lead to a better understanding of the underlying atomic mechanism. This investigation, therefore, is one of a series primarily designed to measure the growth velocity of secondary grains at various temperatures for silver, copper, and aluminum. It is hoped that these studies along with those of orientation relationships, will establish a sound basis for theorizing as to the origin and nature of the secondary transformation. Experimental Procedure The metal used in the present investigation was high-purity silver (999.9 fine), which was supplied in the form of cold-rolled plates 0.250 in. thick. These plates were annealed at 500°C for 1 hr and then straight-rolled to a thickness of 0.04 in. in three reductions of approximately 45 pct, followed in each case by an anneal at 450°C for 1/2 hr. The 0.04 in. sheets were given a final reduction of approximately 50 pct, which resulted in a thickness of 0.02 in., thereby insuring two-dimensional crystal growth. Individual specimens of this material about 1x3 cm were used for all heat treatments, unless otherwise noted. The annealing was carried out under an atmosphere of argon in an Inconel tube furnace whose temperature was controlled to within -+2°C. Metallographic examination of the secondary transformation was accomplished by mechanically polishing the specimens on one side to approximately one half their thickness through 2/0 metallographic emery paper, and then electrolytically polishing in a solution of potassium ferrocyanide and sodium cyanide. With a current density of approximately 20 amp per sq dm, the time required to obtain a satisfactory surface varied from 3 to 5 min. Standard potassium bichromate was used to etch the electrolytically polished surfaces. A heavy etch with this solution produced a sharp contrast between the secondary grains and the fine-grained primary structure, darkening the latter while leaving the large secondary grains bright. All area measurements of the secondary crystals were made with a planimeter on enlarged tracings of the grains.

Jan 1, 1953

By A. Styka, G. Fischer, S. Tour

Described herein are the results obtained during research work involving coating titanium alloys with molybdenum by vapor-deposition methods. Results show that the method can be used successfully to deposit hard adherent wear-resistant coating of methodmetallic molybdenum on titanium or titanium alloys without changing the microstructure of the titanium base. PRODUCTION and use of titanium and its alloys have increased tremendously in the past few years. The physical, mechanical, and chemical properties of this engineering metal have caused considerable enthusiasm among metallurgists and engineers. However, as with all materials, there are some drawbacks. For example, titanium is susceptible to seizing and galling on wearing surfaces. In order to produce a good wear-resistant surface, many investigations have been conducted evaluating oxidizing, carburizing, nitriding, carbonitriding, sili-conizing, and chromizing of titanium. All of these processes require high temperatures for rather extensive periods of time. It has been possible to produce hard surfaces on titanium and its alloys by a number of these processes at the expense of a deterioration of the physical properties of the base material. A practical solution to the problem of providing titanium and titanium alloy parts with a satisfactory wear-resistant nongalling surface must be one that does not involve excessive temperatures for long periods of time. Sam Tour & Co. Inc. has completed a research and development contract for the United States Army Ordnance Corps on vapor deposition of molybdenum on titanium and titanium alloys. On the basis of results obtained from the research program, titanium alloys can be coated successfully with molybdenum to provide a hard wear-resistant surface without harm to their base mechanical properties. The remainder of this article is a description of the techniques used to apply the coating and the results obtained from wear tests on molybdenum-coated titanium. Theory Basically, the technique used was the application of molybdenum by a vapor-deposition method, thermal decomposition of molybdenum hexacarbonyl [Mo(CO)] with hydrogen as the carrier gas. The selection of this method was based chiefly on the following considerations: 1—low plating temperature which would minimize excessive grain growth, 2— low decomposition temperature of the carbonyl, 3— possibilities of controlling the hardness of the plate by adjusting the carbon content using the plating temperature and pressure as the primary variables, 4—use of high vacuum, thereby avoiding unnecessary oxidation and other complex reactions with the atmosphere. Free energy data1 show the strong tendency for titanium to combine with O2 N2 or carbon from normal temperatures to temperatures above its melting point. To maintain the titanium in a film free condition, the use of as high a vacuum as possible is indicated. The literature' indicates that the reaction product of hydrogen with titanium is unstable in vacuum at around 400°C. 5—Although it is indicated from the thermodynamic standpoint that there is little possibility of removing carbon from either titanium or molybdenum, the work of Lander and Germer -ndicates that the use of a suitable H,/CO ratio is somewhat effective in minimizing carbon deposition. 6—Availability of molybdenum carbonyl. In the simplest form, the conditions of equilibrium3 in chemical reactions involving decomposition of carbonyl are as follows: Mo (CO) ? Mo + 6CO 2CO * C + CO,. The plating rate is proportional to the rate of evolution of CO from the decomposed carbonyl, i.e., it is proportional to the pressure of the gaseous decomposition products. Carbon released from CO gas is the significant constituent for the variability of the physical properties of the product. High carbon deposition is favored by increasing pressure. Limitations are imposed in the selection of plating temperature and pressure. Excessive temperature re-

Jan 1, 1956

By Dorsey Hager

The information given in the accompanying table is submitted as evidence confirming the application of the anticlinal theory and the value of geology in the Kansas and Oklahoma oil fields. The term anticline has been used to define a particular type of arched fold. The anticlinal theory of oil accumulation should, however, be broadened to include any structural fold of an arched type even if not a distinct anticline. A terrace may very properly come under the heading of the anticlinal theory of accumulation, as the folding is closely related to that of the anticline; in fact, in many cases is an arrested anticline, though not completely closed in all directions. Stratigraphic forms due to lensing or irregular cementation of the sands certainly cannot be considered to fall within the anticlinal theory, though the laws of accumulation may be similar. A dome is similar to an anticline and belongs to the same class. A dome is broader in proportion to its length than an anticline. Many anticlines undulate along their axes to form domes. The anticlinal theory in this discussion will then be applied to anticlines, domes and terraces. In the following list, the writer has tabulated the main oil fields of Oklahoma, and a few recently discovered fields in Kansas. The fields discovered within the past 4 years are listed with the date of their discovery. Under "How found," the writer puts "Wildcat" where a geologist has not been employed, "Geology" where it has been used, and "7" where there is doubt. In some places the geologists have claimed pools that may rightly belong to them, but their claims have been questioned, so that they belong in an unsettled category. Unless one has mapped all the old pools, it is not possible to say just how far they are dominated by structure, but from our own work, and from discussions with others, it is safe to venture that nearly all the "shallow-pool" districts, Nowata, Bartlesville, and the Eastern Osage, are controlled by structure; domes, noses, and terraces are the main structural features. The "shallow pools" of Kansas show the same relation. At Peru and at Sedan, domes are evident, though gas occurs high on the domes, and oil well down the flanks, leading some to believe

Jan 1, 1917

By J. R. Long, E. L. Anderson, R. S. Dean, F. S. Wartman

TITANIUM has been estimated to comprise about 0.65 per cent of the earth's crust and ranks fourth in abundance among the metallic elements suitable for engineering uses. In spite of this, applications of titanium for structural purposes have not as yet been developed. Its commercial exploitation has been largely confined to the chemical industries and the production of paints and pigments; no doubt because of the difficulties that lie in the way of preparing the pure ductile metal. Published reports, however, indicate that ductile titanium can be prepared and possesses some unique properties. This, together with the occurrence in this country of several important titaniferous deposits, has led the Bureau of Mines to investigate processes for the production of metallic titanium, 'methods required for its fabrication, and the properties that may be produced in this interesting metal. METHODS OF PREPARING METALLIC TITANIUM Many early investigators claimed to have isolated metallic titanium; but in the light of present knowledge, it seems that they really had produced various mixtures of carbides and nitrides that have a metallic appearance but are brittle, hard, and unworkable. The first metallic titanium pure enough to be malleable when cold was produced by Hunter1 in the early part of the twentieth century. Kroll,2 van Arkel,3 and Fast,4 subsequently confirmed the facts that pure titanium is a ductile metal and that small amounts of impurities were responsible for previous reports of brittleness. When heated, titanium reacts chemically with various gases, such as hydrogen, oxygen and nitrogen; if the volume of gas thus absorbed is too great, the metal becomes brittle and unworkable. The principal difficulty in making ductile titanium is prevention of such contamination, and the success of a given process may be judged by the completeness with which it solves this difficulty in a practical manner. Of the gases mentioned, hydrogen is the least objectionable, since its absorption by the metal is completely reversible and, although dimensional changes occur and absorption of hydrogen embrittles the metal, the gas may be removed readily by heating in a high vacuum for a short time. On the other hand, the absorption of oxygen or nitrogen results in the formation of permanent 'solid solutions of the oxide and nitride, which cannot be decomposed by the strongest reducing agents2 with sufficient completeness to restore the inherent ductility of the metal. Because of

Jan 1, 1946

By W. R. Seyfried

The problem of extracting alumina from clay and low-grade bauxites has been the subject of considerable interest for some time. The basic reason, of course, lies in the fact that known reserves of high-grade bauxite are not inexhaustible and that the present commercial process cannot successfully cope with low-grade bauxites or clay. Ultimately it may be necessary to use these poorer raw materials for all commercial operations. An unprecedented demand for aluminum during the war emergency and the constantly threatened shortage of imported bauxite caused the United States Government to take an active role in this problem. Through the National Academy of Sciences, the War Production Board and the Defense Plant Corporation, it investigated processes and finally selected four to be used in the construction and operation of four experimental plants. Each plant was to be designed in such a way as to facilitate its incorporation into a larger commercial plant should the need arise. The Chemical Construction Corporation process, or "Chemico" ammonium sulphate process as it is better known, was one of the four selected. The extensive literature and patents on record before the war generally follow one of two process-types depending upon the extracting reagent used. One group uses an acid reagent, the other an alkali. The Chemico process uses an acid reagent. For those interested in other processes described in literature, there is a short bibliography at the end of this paper. The basic steps of all acid extraction processes are: (I) to make the aluminum silicates acid soluble, (2) to separate the released alumina from impurities and insoluble gangue, and (3) to recover the reagent for re-use. The Process as Planned In April 1941, a group of chemists and engineers of the Chemical Construction Corp. became interested in the problem of extracting alumina from clays and low-grade bauxites and, under the leadership of Mr. Blakeslee Barnes, Vice President and General Manager of the company, first drafted a process in July of that year—five months prior to Pearl Harbor. The work continued in our research laboratories and with a small pilot plant. By June 1943, the work had progressed to a point where it was possible to apply for a patent on the process which was U.S. patent 2,405,426, granted August 6, 1946. Immediately prior to the development of the Salem plant, the process was envisaged to be as follows: I. The first step was to make the aluminum silicates acid soluble. It was planned: (a) Clay or lour-grade bauxite would be roasted at 700 to 800°C (1292° to 1472°F). (b) The roasted ore would then be leached with hot aqueous ammonium bi-sulphate to form a slurry. In this way the

Jan 1, 1949

By A. E. Deruyttere, J. Van der Planken, M. Laurent, Van den Bergen

FahRENHORST and schmid1 observed that zinc single crystals work hardened less rapidly when strained in liquid air (- 185°C)than in a bath at -82°C, whereas at higher temperatures the rate of work hardening decreased with increasing temperature, as would be expected. Cadmium and magnesium showed no such decrease at -185°C. At that time the observed anomaly for zinc at liquid air temperature probably seemed insignificant. However it later was confirmed2 by experiments in liquid nitrogen (-196°C) and in the mixture solid carbon dioxide-acetone (-77"C) and therefore appeared to be real. seeger3 then suggested that the anomaly might be due to the different wetting of the zinc crystals by the cooling media. Recently a new confirmation was obtained,4 however the cooling media again were different: the rate of strain hardening was found to be lower in liquid nitrogen and liquid oxygen than in pentane cooled to various temperatures down to -126°C. Ekperiments will now be reported in which the medium surrounding the specimen at the different temperatures was the same, namely gaseous air. The single crystals were made from "Overcor 99.99" zinc. They were grown in a vertical traveling furnace on seeds of nearly the same orientations. The diameter of the crystals was 5 mm and the length between shoulders 140 mm. The brass shoulders were stuck to the crystals by means of araldite. A thin steel wire was fixed to each shoulder and served to fasten the specimen to a Houns-field tensile testing machine. The crystals with the shoulders and part of the wires were surrounded by two concentric cylindrical containers. The coolant. either liquid air or ground solid carbon dioxide, was poured into the outer container only. During cooling the containers rested on a support which was removed when the straining was started. In order to check the temperature which the crystals would attain inside the inner container, a hollow bar of zinc in which a thermocouple was fitted was first mounted in the apparatus as a substitute for a crystal. It appeared that a constant temperature, respectively - 183° and -72°C, was attained inside the bar, if a soaking time of the order of 1 hr was allowed and if the outer container was constantly kept filled. Accordingly, this procedure was adopted for every tensile test. To take account of the large scatter, fourteen tensile tests were performed with liquid air and seven with solid carbon dioxide. The orientation of the crystals and the results are presented in the table, in which the symbols have the following meaning: 1 : temperature x : initial angle between basal plane and specimen axis : initial angle between slip direction and specimen axis a : shear strain at fracture 0: average rate of strain hardening = —-——- 100 t0 and Te representing respectively the critical shear stress and the shear stress at fracture. Despite the scatter of the a- and 8— values which is of the same order of magnitude as in the work reported by Seeger and Trzuble,4 it is evident that the strain hardening rate is significantly lower at -183°C thanat-72°C. The table also contains the average values calculated from Seeger and Trauble's results at the corresponding temperatures: z.e., four results at -183oC and two at-70°, -71°C. These authors calculated 9 in a slightly different way, but this is unimportant. The agreement between the a-values shows that both sets of experiments are comparable despite the differences in experimental techniques. The rates of strain hardening also agree and it may therefore be concluded that the anomaly is not

Jan 1, 1962

By C. R. Criss, R. J. McCormick

ThiS paper .summarizes the development and perform. ance of the Coldwater Oil field, Isabella County, Mich. Production is obtained at a depth of 3750 ft from a dolomite reservoir, which is probably both Rogers City and Dundee. There appears to be no persistent barrier to vertical fluid movement between the Rogers City and Dundee, and both formations are believed to have a common original oil-water contact. No we1ls are open to production at the level of the Dundee. The discovery of the field in 1944 was followed by the drilling of 81 producing wells and nine dry holes. By the end of 1952, the field had produced 12,763,000 bbl of oil, at which time 69 active wells were producing 3600 B/D oil and 21,000 B/D water. The reservoir has an effective natural water drive, and bottom-hole pressure has declined 75 psi from an original pressure of 1453 psi. Oil is undersaturated at reservoir conditions with a solution GOR of 512 cu ft/bbl and a saturation pressure of 1190 psi. INTRODUCTION Although the Coldwater Field is now in its ninth year of production, it ranks seventh in cumulative recovery, and second in current daily oil production in the State. Following complete development of the field in 1946, it has consistently contributed approximately 11 per cent of Michigan's daily production. Coldwater appears to have a greater pay thickness than most fields producing from the Rogers City forma- tion in the west central part of the Michigan basin. Except as influenced by the extent of closure and the thickness of the oil column, reservoir performance is believed to be representative of Rogers City fields in this part of the basin. For this reason, it is felt that the following presentation of factual data for the field will be of general interest. HISTORY AND DEVELOPMENT Discovery of the Coldwater field during Aug., 1944, followed favorable subsurface geological correlations and core tests drilled to a shallow stratigraphic marker horizon. The field is located in the west central part of the Michigan Basin in Coldwater Township (T16N-R6W), Isabella County. It is 60 miles west-northwest of Bay City, and near the geographic center of the southern peninsula of Michigan. The discovery well flowed 200 bbl of oil the first 24 hours from the Rogers City dolomite at a depth of approximately 3750 ft. Field production is principally from the Rogers City with a minor amount assumed to come from the underlying Dundee dolomite, although none of the wells are open to production at the level of the Dundee. Both the Rogers City and Dundee formations belong to the Devonian system (See Geologic Column-Fig. I.) In addition to Rogers City-Dundee oil production, sweet gas is produced from the Michigan Stray sand of the Mississippian system at a depth of 1400 ft. The gas reservoir has approximately the same areal extent as the underlying oil reservoir. Although gas production is an important feature of the Coldwater field, this report is concerned only with the oil reservoir. The productive area is approximately 3200 acres. The pool is developed on a 40 acre spacing pattern with wells drilled in the center of the north half of 40 acre tracts, except for a few off-pattern wells drilled along

Jan 1, 1955

By Ralph Sweetser

THE present state of iron blast-furnace practice is metallurgical rather than mechanical; the tend-ency is toward intensity rather than toward ex-tension. The engineers have built blast furnaces big enough and strong enough, and have furnished accessory equipment ample and accurate enough for the present state of the art, but the metallurgical side has been too much neglected; the metallurgist, rather than the engi-neer, is now the man on whom the present and future progress in iron blast-furnace practice depends. The mining engineer has produced great tonnages of iron ores, and has kept ahead of the demands for quantity; now the metallurgist is improving the chemical and physical qualities of this product by ore-dressing and other forms of beneficiation. For a generation or more, the principles of mechanics have had most influence in the advancement of iron blast-furnace practice; atten-tion now is given more to the principles of metallurgy, chemistry, and ore-dressing. This metallurgical progress is taking place inside and outside the blast furnace. The two great determining factors of the inside operation are the slag, and the rate of combustibility of the coke. Outside the fur-nace, the progress is, and will be, along the lines of more careful mixing of ores and iron-bearing materials, in the sizing and washing of limestone, and in the char-acter and structure of byproduct coke.

Jan 3, 1922

By Fred Bond

THERE is acute need for a method that will measure the size distribution of finely di-vided materials, particularly when the par-ticle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the sam-ples produced are adequate for a consider-able amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determina-tions of fineness and surface area, which are important in many industries. The sedimentation balance consists essen-tially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the set-tling rate. The balance appears to be in-herently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have re-stricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investiga-tion might lead to modifications that would make it a valuable tool for the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribu-tion determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used, in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared, early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could he accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the dis-tribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1939

By J. H. Hensley

The mine of the Miami Copper Co. is in the Miami district, Gila County, Ariz., approximately 7 miles west of Globe. In 1906, the General Development Co. secured the ground now owned by the Miami Copper Co., and about a year later discovered ore in a prospect shaft at a depth of 220 ft. The Miami Copper Co. was organized in 1907, the claims held by the General Development Co. were transferred to it, and an active development campaign was inaugurated. The railroad was extended from Globe to Miami in 1909, a concentrating plant was constructed, and the company began producing early in 1911. The unit size of mineral tract in the district is the standard lode claim 600 ft. in width by 1500 ft. in length. Ownerships of land are held in fee. The geology of the district has been described by F. L. Ransome.' The formations of local importance are: The pre-Cambrian Pinal schist, which consists mainly of metamorphosed sedimentary rocks and is commonly of a thinly laminated sericitic variety; the diabase, which is thought to have been intruded in late Paleozoic or early Mesozoic times; the Schultze granite and granite porphyry, considered early Tertiary; the dacite of late Tertiary time; and the Gila conglomerate of early Quaternary. General Items Influencing Mining Methods The bodies of disseminated ore in the district are flat lying masses of irregular outline and variable thickness. As a rule, these masses lack definite boundaries; the orebody follows a curve along one of the main ridges, approximately 5500 ft. in length with a maximum width of 1600 ft. The minerals occur as finely divided and uniformly disseminated chal-cocite in the Pinal schist and Schultze granite. The typical overburden or capping is a barren rusty brown, very friable, highly siliceous, leached schist, or granite-porphyry. The topography of the district is fairly rugged and irregular; the altitude ranges from 3400 ft. above sea level, at the town of Miami, to 3900 ft. on the hills above the Miami orebody. The climate is mild; the mean annual temperature is 63.°F.

Jan 1, 1925

By M. E. Grimes

Rio Algom Mines Ltd. owns eight uranium mines and mills in the Elliot Lake district of Ontario, seven of which were producing before 1960. At present only one mine is operating and meeting current contract requirements. Under present economic conditions, it is not feasible to mine ore of less than 2.0 lb per ton U3O8, although there are very large reserves below this grade, Rio Algom is interested in preconcentration for three possible applications: to extend ore reserves by permitting use of lower grade ore, to reduce costs on processing of present grade ore, and to reduce capital investment in expanding production to meet future production goals. Rio Algom has been investigating various applicable preconcentration processes since the early 1950s to date, on laboratory and pilot-plant scale. Methods investigated include gravity concentration by sink-float, high intensity wet magnetic separation, flotation of uranium, flotation of acid consumers, and a number of electronic sorting methods including radiometric, photometric, and conductimetric. No method tested has yet been satisfactory under Rio Algom's criteria of uranium recovery and cost, principally because uranium loss has been too high for a useful weight rejection. Metallurgical results of the preconcentration test work and the economic assessment therefrom are reviewed.

Jan 1, 1974

By C. E. Arnold

A brief description of this installation was included in a recent paper by H. Kenyon Burch.l The purpose of the present paper is to amplify Mr. Burch's description, as it is felt by the writer that the subject merits more than passing attention. In making a comparison between the common method of hoisting men in mine shafts, and elevator practice in high buildings, the former shows to great disadvantage both as regards safety measures and smoothness of operation. It is surprising that in view of the inducements offered, the step of applying the building equipment direct to the mine shaft has not been taken before, as in many respects the conditions of service are similar, and the objects to be attained are identical. Even without doing this, it is certain that safety to life and limb in the usual method of hoisting men underground can be greatly enhanced by the application to the mine hoist of some of the features of the building elevator. In the case under consideration, the elevator cage runs in a vertical, concrete-lined shaft compartment 5 ft. 11 in. by 5 ft. 6 in. (1.8 by 1.68 m.) in section and 585 ft. (178 m.) deep, while the counterweight runs in the pipe and ladder compartment of a twin shaft 102 ft. (31 m.) distant. The section of the division of this compartment occupied by the counterweight measures 2 ft. 4 1/4 in. by 3 ft. 101/2 in. (0.72 by 1.18 m.), and the counterweight is made in the form of a small cage which suffices to carry two men for the purpose of making inspections or repairs in the pipe and ladder way. The hoist is designed to carry a load of 7500 lb. (3401.94 kg.), ex-clusive of the cage, which weighs 7500 lb., at a maximum speed of 800 ft. (243 m.) per minute. It is installed in the main hoist and compressor building about 220 ft. away from the elevator shaft and is driven by a 160-hp. direct-current motor which is served by a 190-hp. motor generator set. A small direct-current generator mounted at the end of the motor generator set furnishes the current for the controller magnets, brake and fields of the hoist motor and generator. The drum, which is 72 in. (1.83 m.) in diameter, is driven through the medium of a single reduction herringbone gear. A Francke flexible coupling connects the

Jan 1, 1918

By G. L. Oldright

Nearly all of the present schemes for treating complex (i. e. lead-silver-zinc-copper) ores are based on the idea that lead holds, and will hold for some time, the strongest economic place from the viewpoint of supply and demand of all the non-ferrous metals. Copper, it is thought, will come back to its own when European affairs are stabilized, although at that time competition from Chile, Peru, and Katanga, in particular, will be more severe than in pre-war days. The future for silver and for zinc is uncertain. New uses are developing for zinc, and the market has remained better than many expected, but the stabilization of world markets will bring in foreign competition instead of relief. The cost of producing zinc from simple zinc ores, by the retort process, will, from the nature of the labor required and the increasing cost of fuel, increase steadily. As a result, the small producers of purely zinc ores around Joplin are shutting down their mines, even with a good market price for zinc; on the other hand, the producer of lead from complex ores, in the Rocky Mountain states, is confident of a profit from the sale of his lead, and is seeking means to make the zinc in his ore pay some part of the cost of treatment. However, the tonnage costs for mining and ore dressing are much higher in the Rocky Mountain states, as may be seen by comparing tax-return statements from the various states. Even before the recent drop in the price of silver, many mines were operating on a very slender margin of profit; labor and supplies cost more. Mining at greater depth has shown most orebodies to grow increasingly more complex, so that improvements in mining and ore-dressing practice have not been sufficient to compensate for the additional expense involved in beneficiating these ores. The smelters have bad to meet the same general economic situation, so they can only give

Jan 1, 1924

By R. S. Dean

THE numerous theories of hardening which have been advanced in recent years are all satisfactory in accounting for some of the phenomena observed in hardening metals, but none so far presented account for all of the facts observed. Some years ago one of the authors, R. S. Dean,1 presented a theory to account for some of the properties accompanying work hardening. The present paper develops this theory further in the light of recent experimental, work and extends it to other forms of hardening. Many of the ideas included have come from the writings and personally communicated thoughts of others. We have attempted to give proper credit in every case, but it is possible that we have not always done so. As an historical basis it is desirable here to review very briefly the hardening theories which have been current. The first comprehensive theory of work-hardening phenomena was due to Sir George Beilby.2 He contributed the idea that with cold work part of the structure of the metal was rendered amorphous and that it was to this amorphous material that the cold-worked metal owed its difference in properties. According to Beilby's theory this amorphous material was a super-cooled liquid and, therefore, had the characteristics of a vitreous material. That such a theory is not capable of explaining the property changes in metals has been repeatedly pointed out. This theory also allowed a slip to take place only once on a given plane, which, as has been pointed out by Jeffries and Archer,3 is not consistent with the observed length of an individual slip and the amount of elongation which can be obtained by wire drawing. The modifications, which have been proposed to this hypothesis to make it coincide with the experimental facts, have to a considerable extent robbed the theory of its clean-cut characteristics. The commonest of these modifications replaces the amorphous phase with an

Jan 1, 1927

By Malcolm C. Bridges

A review of the application of geomechanics to open stope mining in Australia was recently undertaken for the Australian Mineral Industries Research Association (AMIRA). It compiled the current state of geomechanics and its application to open stope mining, and recommended avenues of research which should be supported by the industry. Information was compiled for eleven mines which use the method. This included their geological setting, the performance of the mining and evolution of the method, properties and behaviour of rock and backfill, and techniques for measurement and analysis. Open stoping accounts for about two-thirds of production from underground mines in Australia. In the future this proportion will progressively increase and the method will become more complex. Overall, the method is being sucessfully applied, but its full potential is not being achieved because a range of problems and limitations are evident within the mines. Many of these are common to several or more mines. These include: zones of poor ground conditions that delay access and stope development; crown pillars that are irrecoverable; substantial overbreak from the walls and backs of stopes; and lack of a widely accepted method to design systems of stopes. Generally, geotechnical information and techniques for applying it to mining are well-developed. However, it nee

Jan 1, 1983

By A. Kenneth Schellinger

DURING the comminution of a brittle material in the presence of dry air, no known phase change or chemical reaction takes place. The energy changes associated with the comminution are those of the transformation of kinetic energy into heat energy and the energy absorption represented by the actual rupture of molecular and/or ionic bonds. The random nature of the actual grinding process in a tumbling-mill often precludes the effective application of a rupture force on each individual particle of brittle mineral present. The result must be a great deal of useless vibration on an atomic scale in both the brittle mineral and the grinding medium below the elastic limit, which vibration is eventually manifested as heat energy in the mill. The actual rupture of molecular, or ionic, bonds creates new surface on the brittle minerals; each square centimeter of this new surface then must possess a number of potential bonds, each of which could reform theoretically with the release of energy. The sum total of this potential energy of bonding per unit of new surface, minus bond satiation effects of the enclosing gas or liquid, must be the surface energy of the mineral. If the comminution of the brittle mineral were carried out within the chamber of a calorimeter, the energy released as heat could be determined rather accurately. Moreover, the total kinetic energy input to the comminuting mass (mineral and medium) conceivably could be derived by a suitable torquemeter and revolution counter if the whole calorimeter were revolved. The difference between these two energy figures should then represent the net energy (gross energy input—heat enerb output) used in creating new surface, gliding or slip on atomic planes, twinning, and possibly other lattice rearrangements within the mineral. If it be postulated further that with a hard, brittle crystalline material, such as quartz, the energy used to produce gliding, twinning, and other permanent lattice movements is a very small fraction of the total net energy absorbed, then this energy absorption within the grinding calorimeter can be ascribed to the creation of new surface energy alone. Such energy is, from the thermody-namic standpoint, the true effective work of the grinding device, in this case a tumbling-medium mill. The ratio of this effective work (in calories) to the total energy input (in calories) should express the thermodynamic efficiency of the comminution taking place under the conditions used in the grinding calorimeter. This approach to the measurement of the energetics of tumbling-mill grinding was suggested by some previous work by Fahrenwald and coworkers' with a laboratory ball mill and a thermometer. They measured the efficiency of grinding based on the formula: Pct Grinding Efficiency = Energy (calories) — Thermal Energy x 100 1npZ Output (calories) Energy input (calories) Efficiencies thus measured, while grinding quartz sand, ranged from 19.7 pct to 7.4 pct. Cook in 1915,' used this approach to the problem of grinding efficiencies in stamp batteries and obtained the energy input by stamp weights times drop distances and the energy output by means of thermometers and pulp flow rates. He calculated that 80 pct of the input energy to the stamp shoes was wasted as sensible heat in the ore pulp. No other studies of comminution by this method of energy differences came to the author's attention. Reasonable agreement as to the order-of-mag-nitude of comminution efficiencies in tumbling-media mills is lacking in the literature. There is a widespread impression among technical workers that the grinding efficiency of the industrial ball mill may be on the order of 1 pct, or even a fraction

Jan 1, 1952

By Charles R. L. Oder, Howard W. Miller

Approximately 5000 tons of zinc ore a day was mined during 1943 in the Mascot-Jefferson City district in East Tennessee. This ore came from the Kingsport formation, a part of the Knox dolomite, of Ordovician age. The Kings-port is composed of 350 to 400 ft. of limestone and dolomite. Thin cherts, sandy layers and shales are numerous. Frequently, the limestones are altered to crystalline dolomite. The Kingsport is divisible into four main lithologic zones. These divisions are illustrated in an accompanying table, which gives detailed sections of the ore-bearing beds as found in the mines and shows the exact positions of the various ore zones within the formation. Key beds are described and the practical applications of stratigraphy in mapping, prospecting and mining are discussed. Introduction The Mascot-Jefferson City zinc district is in Knox and Jefferson Counties, in the Great Valley of East Tennessee. It extends from Mascot, I3 miles northeast of Knoxville, to Jefferson City, about 30 miles northeast of that city. The American Zinc Company of Tennessee is producing from five mines in the district, in which it has operated for more than 30 years. The only other important producer is the Universal Exploration Co. The approximate daily production of the district in 1943 was 5000 tons of sulphide ore, grading from 2.5 to 6 per cent zinc. Small amounts of oxidized ore are mined intermittently. The Knox dolomite has been described by various geologists,'-' but no detailed descriptions of the rock sections revealed by mining have been published. Rock units are not conspicuously different and careful study is required to distinguish them. Nevertheless, familiarity with the stratigraphy of the mineralized zones is essential to successful exploration and extraction of the ores; therefore the purpose of this paper is to give detailed stratigraphic sections as measured in the mines, to discuss their important features and to show their relationship to the stratigraphy of the district. Generalized Section Table I gives the most characteristic general features of the major stratigraphic units. The formation names given in parenthesis are locally and widely used terms, the correlations of which are not necessarily established. For this reason they are put in quotation marks and are replaced by more restricted terms. The names "Mascot" and "Kingsport" were adopted from local towns. They were chosen jointly by Josiah Bridge, of the Federal Geological Survey, and the senior author for use in their separate unpublished manuscripts describing the Knox dolomite in East Tennessee. Descriptions of the type sections may soon be published. The name "Longview" was first applied by Butts6 in Alabama.

Jan 1, 1949

By Howard W. Miller, Charles R. L. Oder

Approximately 5000 tons of zinc ore a day was mined during 1943 in the Mascot-Jefferson City district in East Tennessee. This ore came from the Kingsport formation, a part of the Knox dolomite, of Ordovician age. The Kings-port is composed of 350 to 400 ft. of limestone and dolomite. Thin cherts, sandy layers and shales are numerous. Frequently, the limestones are altered to crystalline dolomite. The Kingsport is divisible into four main lithologic zones. These divisions are illustrated in an accompanying table, which gives detailed sections of the ore-bearing beds as found in the mines and shows the exact positions of the various ore zones within the formation. Key beds are described and the practical applications of stratigraphy in mapping, prospecting and mining are discussed. Introduction The Mascot-Jefferson City zinc district is in Knox and Jefferson Counties, in the Great Valley of East Tennessee. It extends from Mascot, I3 miles northeast of Knoxville, to Jefferson City, about 30 miles northeast of that city. The American Zinc Company of Tennessee is producing from five mines in the district, in which it has operated for more than 30 years. The only other important producer is the Universal Exploration Co. The approximate daily production of the district in 1943 was 5000 tons of sulphide ore, grading from 2.5 to 6 per cent zinc. Small amounts of oxidized ore are mined intermittently. The Knox dolomite has been described by various geologists,'-' but no detailed descriptions of the rock sections revealed by mining have been published. Rock units are not conspicuously different and careful study is required to distinguish them. Nevertheless, familiarity with the stratigraphy of the mineralized zones is essential to successful exploration and extraction of the ores; therefore the purpose of this paper is to give detailed stratigraphic sections as measured in the mines, to discuss their important features and to show their relationship to the stratigraphy of the district. Generalized Section Table I gives the most characteristic general features of the major stratigraphic units. The formation names given in parenthesis are locally and widely used terms, the correlations of which are not necessarily established. For this reason they are put in quotation marks and are replaced by more restricted terms. The names "Mascot" and "Kingsport" were adopted from local towns. They were chosen jointly by Josiah Bridge, of the Federal Geological Survey, and the senior author for use in their separate unpublished manuscripts describing the Knox dolomite in East Tennessee. Descriptions of the type sections may soon be published. The name "Longview" was first applied by Butts6 in Alabama.

Jan 1, 1949