Search Documents

By W. F. Netezband, E. H. Crabtree

The productive area of asphalt-bearing sandstone in Missouri is near the Missouri-Kansas state line near Nevada, the county seat of Vernon County about 100 miles south of Kansas City. While production thus far has been confined to Vernon and Barton counties, there are known deposits in adjacent counties. The area is served by four railroads: the Missouri Pacific, the Kansas City Southern, the Missouri-Kansas & Texas, and the St. Louis & San Francisco. The plant of the Reliance Rock Asphalt Corporation is in Vernon County, about 5 miles west of Nevada, at Ellis, a flag station on the Missouri, Kansas & Texas Railroad. A siding has been built to the plant SO that the finished product can be loaded directly into railroad cars. The property consists of a lease of 240 acres in one block. All portions of the property not required for quarrying or processing the asphalt-bearing sandstone are used for farming by the fee owner. The entire tract is very flat so that there are no transportation difficulties from quarry to plant. Geology The commercial asphalt-bearing sandstones are all of Pennsylvanian age, the major portion of the production coming from the Cherokee formation, the basal member of the Des Moines group. The Cherokee formation includes all beds between the base of the overlying Fort Scott limestone and the Mississippian limestones below. It underlies most of the area, but in the west and northwest townships of Vernon County, and elsewhere in local outliers, the Henrietta limestone, forming mounds, escarpments and high ridges, covers the Cherokee, and is in turn covered by the Pleasanton shale. In the eastern portion of the counties, the Mississippian limestones are exposed. The thickness of the Cherokee varies according to the amount that has been removed by surface erosion. Where fully present under the Henrietta; it is approximately 375 ft. thick, but over most of the county it ranges from 100 to 200 ft. thick.

Jan 1, 1938

By E. H. Crabtree, W. F. Netezband

The productive area of asphalt-bearing sandstone in Missouri is near the Missouri-Kansas state line near Nevada, the county seat of Vernon County about 100 miles south of Kansas City. While production thus far has been confined to Vernon and Barton counties, there are known deposits in adjacent counties. The area is served by four railroads: the Missouri Pacific, the Kansas City Southern, the Missouri-Kansas & Texas, and the St. Louis & San Francisco. The plant of the Reliance Rock Asphalt Corporation is in Vernon County, about 5 miles west of Nevada, at Ellis, a flag station on the Missouri, Kansas & Texas Railroad. A siding has been built to the plant SO that the finished product can be loaded directly into railroad cars. The property consists of a lease of 240 acres in one block. All portions of the property not required for quarrying or processing the asphalt-bearing sandstone are used for farming by the fee owner. The entire tract is very flat so that there are no transportation difficulties from quarry to plant. Geology The commercial asphalt-bearing sandstones are all of Pennsylvanian age, the major portion of the production coming from the Cherokee formation, the basal member of the Des Moines group. The Cherokee formation includes all beds between the base of the overlying Fort Scott limestone and the Mississippian limestones below. It underlies most of the area, but in the west and northwest townships of Vernon County, and elsewhere in local outliers, the Henrietta limestone, forming mounds, escarpments and high ridges, covers the Cherokee, and is in turn covered by the Pleasanton shale. In the eastern portion of the counties, the Mississippian limestones are exposed. The thickness of the Cherokee varies according to the amount that has been removed by surface erosion. Where fully present under the Henrietta; it is approximately 375 ft. thick, but over most of the county it ranges from 100 to 200 ft. thick.

Jan 1, 1938

By Gilbert Thiessen

THE use of a pneumatic process for removing fine material (usually less than 48-mesh) is increasing in, the preparation of stoker-size coal. The fine material, produced as a byproduct, is known as dedusting-plant dust. Since fusain is the most friable ingredient in bituminous coal (it may readily be rubbed to an impalpable powder with the fingers), it tends to accumulate in this byproduct. While studying the properties of cokes produced by blending Illinois coals with other materials, considerable quantities of fusain were required. Dedusting-plant dust suggested itself as a-convenient supply. It became necessary, therefore, to determine how much fusain was contained in a measured sample of dust, how the fusain was distributed with respect to size and specific gravity in the sample, and whether or not it would be feasible or desirable further to concentrate or to recover the fusain from, the dust before using it in the blends to be coked. The results obtained indicate the possibilities of production of a high-fusain material.

Jan 1, 1936

By Ralph A. Sherman, John Blizard

The experimental investigation described in this paper was conducted to determine the relative combustibilities of different samples of blastfurnace coke when burned in a current of air in a small furnace. It was undertaken in connection with the work done by Perrottl and Kinney2 on the process of combustion in the blast-furnace hearth.3 Reference is often made to the "combustibility" of coke by blastfurnace men, but exactly what is meant by the term "combustibility" is somewhat vague. Brassert,4 in a paper before a meeting of blastfurnace men in 1914, refers to combustibility as follows: The value of the coke in relation to the heat reactions in the furnace is determined not only by the carbon content but even more so by its combustibility. This, in turn, is governed by its size, the physical and chemical composition of the carbonaceous substance forming the cell walls, and the interior and surface structure of the coke pieces. These properties are, in turn, influenced by the chemical and physical properties of the coals used for coking, the density of the cake of coal in the oven, the coking time, temperature and heat regulation of the ovens, and last, but not least, by the method of quenching, screening and handling the finished coke. What principally concerns the blast furnace is the rate of progression of the combustion, which depends not so much on the chemical analysis as on the physical qualities of the coke. It is this rate of progression that we term combustibility, which is the speed at which the carbon molecules in the coke combine with oxygen under given conditions. In general, what the blast furnace requires is a coke which will burn rapidly and with intensity at the tuyeres, yet which has a sufficiently strong structure and hard surface to resist abrasion and solution by CO2 in the upper part of the stack.

Jan 1, 1923

By John Blizard, Ralph A. Sherman

The experimental investigation described in this paper was conducted to determine the relative combustibilities of different samples of blastfurnace coke when burned in a current of air in a small furnace. It was undertaken in connection with the work done by Perrottl and Kinney2 on the process of combustion in the blast-furnace hearth.3 Reference is often made to the "combustibility" of coke by blastfurnace men, but exactly what is meant by the term "combustibility" is somewhat vague. Brassert,4 in a paper before a meeting of blastfurnace men in 1914, refers to combustibility as follows: The value of the coke in relation to the heat reactions in the furnace is determined not only by the carbon content but even more so by its combustibility. This, in turn, is governed by its size, the physical and chemical composition of the carbonaceous substance forming the cell walls, and the interior and surface structure of the coke pieces. These properties are, in turn, influenced by the chemical and physical properties of the coals used for coking, the density of the cake of coal in the oven, the coking time, temperature and heat regulation of the ovens, and last, but not least, by the method of quenching, screening and handling the finished coke. What principally concerns the blast furnace is the rate of progression of the combustion, which depends not so much on the chemical analysis as on the physical qualities of the coke. It is this rate of progression that we term combustibility, which is the speed at which the carbon molecules in the coke combine with oxygen under given conditions. In general, what the blast furnace requires is a coke which will burn rapidly and with intensity at the tuyeres, yet which has a sufficiently strong structure and hard surface to resist abrasion and solution by CO2 in the upper part of the stack.

Jan 1, 1923

By W. J. Parton

The efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/32 by 1/32 in.) and No. 5 Buckwheat (1/32 in. by 0), pre-sent a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than 3/32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes. The object of this paper is to de- scribe a stationary screen device from which the underflow is restricted by orifices, called a launder screen, along with operating results of several applications of this screen; a settling tank in which two classified products are produced by the installation of a cylindrical partition of smaller diameter than the original tank, one product being recovered from the small tank created by the partition and one product from the space between the inner and outer tank walls; a small pocket classifier or hydraulic trap for use in removing high ash particles from a sludge flow; the classification or segregation of sludge solids occurring in a 16 in. diam pipe flow by analysis of samples procured at different zones; and the operating results of a Fahrenwald sizer, as well as the performance of the concentrating tables handling the classified products. These simple devices were employed at the collieries of the Lehigh Navigation Coal Company Incorporated, Lansford. Pa., in order to improve preparation results on the fine sizes of anthracite. Launder Screens The launder screen is a screening and dewatering device which probably could be used advantageously in the flow diagram of many fine coal plants. Fig 1 shows that it consists of a stationary screen constructed by placing 6 in. high partitions every 6 in. along a launder. Holes are then drilled on 6-in. centers across the bottom of the launder to receive pipe bushings of the desired diameter. The screen cloth is tacked on top of the partitions. When water and solids are fed to the screen, only a small portion of the total water is removed through the orifices in each compartment so that the water in the feed is distributed evenly over the whole length of the screen. The screening action which results is very efficient because the solids are kept in a fluid condition for the full length of the screen. Blinding of the screen can be minimized by the use of screen cloth

Jan 1, 1950

By J. B. Goddard

In situ leaching of uranium by aqueous ammonium carbonate containing oxygen or hydrogen peroxide as oxidant results in the partial dissolution of sulfides. While some of the sulfide sulfur is oxidized to sulfate, a considerable portion is oxidized only to thiosulfate and polythionates. Polythionates poison the ion exchange resin used to extract uranium. At the Palangana operation in south Texas, the trithionate ion (S3062-) was found by infrared spectrometry to be the major resin poison. Treatment of ion exchange feed solutions with hydrogen peroxide only resulted in partial conversion of reduced sulfur species to sulfate. Trithionate conversion was particularly slow. Poisoning of the resin also occurred from the ammonium chloride eluant, which built up trithionate because of recycling. This was essentially eliminated by chlorinating the eluant before yellow cake precipitation.

Jan 1, 1986

By E. O. Wagner, V. F. Parry, W. S. Landers

Following investigations by the Denver Bureau of Mines on drying fine coal in the entrained state, Texas Power & Light Co. employed the fluidized technique to upgrade Texas lignite for use in power plants. Because of the rapidly rising cost of natural gas in Texas the company agreed to cooperate with the Bureau of Mines in studying further the upgrading of lignite by low-temperature carbonization, since potential value of the tar would help off- set the cost of fuel. Considerable interest was aroused, therefore, when Aluminum Co. of America decided to use dried lignite in its 240,000-kw power plant at Rockdale, Texas, operated by Texas Power & Light. Carbonization of coal before burning in a power plant is not new. Plants in Germany have been operated for many years on carbonized brown coal and lignite briquets produced in large integrated plants. Large-scale experiments in carbonizing pulverized coal with hot flue gases were made 30 years ago at Milwaukee, and many inventors have proposed other processes. In the U. S., technical and economic problems have prevented successful operation of large plants on carbonized coal, but new techniques of handling solids in fluidized beds may overcome these difficulties, particularly if the higher volatile noncoking coals are used.

Jan 1, 1956

By M. M. Austin

PURE metallic tantalum, from a practical standpoint, is one of the newer developments in the metal field. Although it was used as filament in incandescent lamps in 1906, only within the last five years has the metal been available in sufficient quantity and suitable form for more general application. In addition to corrosion-resisting properties and high melting point, the metal has an ability to withstand unusual amounts of cold working. It affords some striking demonstrations of block movement during plastic flow.

Jan 1, 1930

By H. R. Hanley

IT is a well-known fact that the solubility of zinc compounds decreases when these compounds are roasted in contact with iron compounds, but descriptions of tests to quantitatively express the fact have not appeared in the literature. Possibly such an expression cannot be uniformly and exactly duplicated by different operators because of the variation in the personal equation. In a general way, however, the reactions between zinc compounds and iron compounds under roasting conditions will show a certain trend with changing conditions and the approximate quantitative expression of this trend appears reasonably well established by experimental work conducted for this purpose.

Jan 1, 1929

By R. Casting, J. Philibert, and C. Crussard

APPARATUS described in this paper uses the properties of X-radiation, emitted by substances under electron bombardment, as a means of rapid chemical point analysis. The method is based upon the principles of emission X-ray spectrography pioneered by Moseley in 1913. A very finely focused beam of electrons—the electron probe—is projected on the surface of a sample, which has a very large area compared with the beam diameter, at the point where it is desired to know the chemical composition. The minute volume of the sample which is thus irradiated emits a complex X-ray spectrum consisting principally of the characteristic radiations of the elements present in the volume. Measurement of the wavelength and intensity of each component of this spectrum thus affords a simple method of determining the chemical identity and concentration of these elements. The volume of sample which is analyzed at each position of the beam is limited by the diffusion of electrons in the sample. For an accelerating potential of the electron beam of about 30 kv, which is a convenient value for producing the characteristic radiation, this diffusion extends over a diameter of about 1 µ normal to the beam, and about 2 µ in the direction of the beam. Thus a beam of 1 µ in diameter leads to a volume of about 2 µ in diameter being irradiated. The limits of the analyzed region are thus considerably smaller than those obtained by using spark or arc emission spectrometry, which must extend to about 50 µ at right angles to the beam, and those obtained in X-ray fluorescence analysis, where the penetration of the specimen is considerably greater. The apparatus itself consists of three main parts: an electron optical system. an X-ray spectrograph and an optical microscope. The electron opticai system consists of a tungsten cathode emitting the electrow and a pair of magnetic lenses which focus the electron beam on the specimen to be analyzed. The specimen is prepared in the usual way, as in optical micrography. The X-radiation, emitted at the focal spot where the electrons strike the sample, is analyzed with a curved crystal, Geiger-Müller counter, vacuum spectrograph. The light microscope, designed to observe the surface of the sample in the region to be analyzed, is provided with a reflecting objective placed on the axis of the second magnetic lens. Its magnification is X450. The quantitative determination of an element A in the analyzed region is made by measuring the intensity I, of a strong characteristic line of the element, as emitted from the sample, and then the intensity I (A) of this same line as emitted from a

Jan 1, 1958

By J. D. Milburn, H. J. Hill

In quantitative interpretation of electrical logs the presence of clay minerals introduces an additional variable which further complicates an already complex problern. Although recognizing the difficulties introduced as a result of the heterogeneity of natural sediments and despite the present incomplete state of knowledge regarding electrochemical behavior of shales, dissemirzated clay minerals and concentrated electrolytes, it was felt that useful empirical correlations might be obtained from experimental investigation. Six typical sandstone formations, having a wide variety of petrophysical properties, were selected for the study. Approximately 45 samples from each formation were selected to satisfactorily represent the range of pore size distribution within the particular formation, As a matter of general interest, four limestone formations were also included in the investigation. Previously proposed equations relating to resistivity, SP and interrelationship of the two phenomena have, where possible, been tested with data obtained in this investigation. These equations do not satisfactorily describe experimental behavior of samples through all degrees of shaliness or throughout the range of brine solution resistivities normally encountered in logging practice. An empirical equation has been developed which quantitatively relates formation resistivity factor to satirrnting solution resistivity, porosity, and "effective clay content." This relation is indicated to be uniformly applicable to clean or shaly reservoir rocks. It is shown that both the SP and resistivity phenomena of shaly samples are related to the sample cation exchange capacity per unit pore volume. The independent chemical determination of this parameter is thus a means of determining the "effective clay content" of samples. Some implications regarding theory and electric log interpretation of shaly sands are discussed. INTRODUCTION The use of electrical resistivity logs as a means for estimating formation porosity is based upon the original work of Archie1. It was shown by empirical methods that the resistivity of a rock, when 100 per cent saturated with brine solution, could be related to rock porosity through the equation, F = Ro/ RW = f-m.......(1) where F, the formation resistivity factor, is defined as the ratio of the resistivity of the 100 per cent water saturated rock, Ro, to the saturating solution resistivity, Rw; f is the ratio of pore volume to bulk volume; and m is the slope of the average line when the data are plotted on log-log paper. This relation was established for relatively shale-free formations containing water having high salt concentrations, and under these conditions F may be considered constant for a given rock sample. Applications of Eq. 1 to interpretation of logs of shale-free formations has been quite successful when satisfactory formation water resistivity data could be obtained. The most readily available means of estimating formation water resistivity is the self-potential log. Conventional methods of SP log interpretation involve correct.

Jan 1, 1957

By Warren E. Wilson

PRESENT-DAY design of launders is essentially an art depending to a marked degree upon the experience of the designer, whose problem is that of determining the dimensions of a conduit that will transport the pulp within the physical limitations of the plant and in the most economical manner. This paper has been prepared in an effort to place launder design upon a more scientific basis. A method is developed from elementary principles and presented in a form that may be used directly by the designer in determining launder dimensions.. The equations that are developed are believed to represent an advance over older ones, in that they give due consideration to all the pertinent variables, either including them in the analysis or showing that they may be neglected within the limits of applicability of the equations. Experimental data from several sources are used in evaluating the coefficients that are not determined in the mathematical analysis. On the basis of the material presented, it is concluded that launders may be designed with a much greater degree of accuracy than previously believed possible, when due consideration is given to all the factors involved in the problem. However, a great deal of work still remains to be done in the laboratory before a complete answer to all the questions in launder design can be made available. HISTORY OF LAUNDER DESIGN Among the references1-11 are cited accounts of many experiments that have been conducted in an effort to advance the knowledge of the flow of liquid-solid mixtures in flumes and pipes. With three notable exceptions, this work was carried on in such a manner that the results have limited value in solving the general problem, since not all the pertinent variables were measured and controlled. The exceptions are found in the works of Blue,6 Gilbert,7 and Blatch,11 who exercised great care in controlling and measuring all the significant quantities involved in the experimentation. It is notable that much of the work done by men directly connected with the mineral industries1-4 lacks somewhat in completeness, owing apparently to preconceived notions concerning the factors that determine the flow. For example, many measurements on flow in pipes and flumes carrying liquid-solid mixtures determined only the slope and percentage of solids, with no mention of size of particles, depth of flow, roughness of channel or specific gravity of solids. Material in current handbooks8,9 and textbooks is based largely on the experimental work cited above. Although most discussions of the topic-include statements that the results to be obtained by using the data presented are limited by the fact that all variables have not been considered, it is

Jan 1, 1943

By Alden B. Greninger

IN a recent study1 of the deformation of metastable beta copper-zinc and beta copper-tin crystals, it was established that the parallel markings that appear on the surface of these crystals after slight deformation represent lattice transformations. Stereographic analysis showed that in beta copper-tin, the poles of these markings deviated one or two degrees from poles of the form 1133). In beta copper-zinc the plane delineated by the markings corresponded to no one crystallographic plane of the matrix lattice; the marking poles deviated from 5° to 11° from poles of the form {110}, and were displaced only a few degrees from (110) zones. Inasmuch as the new transition lattices produced as the result of the deformation are different for each alloy, it was thought at first that the habits of the markings might be the result of a cooperation between matrix lattice and transformed lattice. (Both matrix lattices are body-centered cubic.) Such a cooperative effect is thought to obtain in the formation of Widmanstätten figures, for it is well known that the matrix lattice alone does not determine the habit assumed by a segregate phase. On the other hand, it is not inconceivable that the dissimilarity in marking habit might be due to differences in deformation characteristics of beta brass and beta bronze. Barrett and co-workers2 have shown that slip-line habits in pure iron are markedly different from those in high-silicon ferrite; and although it has been repeatedly demonstrated that plates of a segregate phase do not necessarily form on the slip planes of the matrix lattice, deformation characteristics may be more intimately allied with plate formation when a transformation is made to occur as a result of plastic deformation. However, there is the fact that the orientation of markings in metastable beta copper-zinc is the same whether the markings be produced by quenching, deformation, or liquid-air cooling; likewise, quenching and deformation markings in metastable beta copper-tin are oriented in the same way with respect to the beta matrix. During the course of the investigation referred to above, samples of 52:48 (stable beta) copper-zinc f were deformed and examined micro-

Jan 1, 1938

By A. S. Adams

A glance at the list of papers1 that have been published since 1920 on the general subject of flotation suggests the variety of ideas that exist regarding the underlying cause of the phenomenon. Among these ideas, we find several coherent theories, but none that adequately and completely explain the phenomenon. Ralston2 and Bains3 suggested an electrical theory which has to do with the attachment of mineral particles to a bubble by the attraction of unlike electrical charges. This theory has its root in the fact that a bubble of air in pure water is electrified in such a way that the surfacc is negatively charged while the body of the water is positively charged. This result, which was first discussed by Helmholtz, also obtains when the water contains anything except a high concentration of hydrogen ions, or ions which are trivalent or tetravalent. The theory also holds that the mineral particles have positive charges on their surfaces, and so there is attachment between bubble surface and mineral particles by the old law of electrostatics, which states that unlike charges attract. Contact Angle and Oil Attraction The contact angle—the angle formed by a fluid-fluid boundary when both are in contact with a solid-—has been indicted several times for complicity in the phenomenon of flotation. This angle is supposed to indirectly measure the surface energy of a solid. Thus if we have two fluids in contact with a solid, we may express the difference between the two fluid-solid tensions as equal to the fluid-fluid tension times the cosine of the angle between the two fluids.4 If the two fluids are in contact with the solid, this is, no doubt, an excellent way of establishing relative surface energies. However, in flotation, we deal with substances which are not wetted by water. What assurance have we, then, that the angle

Jan 1, 1928

By G. Sachs, E. J. Ripling, J. J. Lynch

INTRODUCTION General IT is general practice to evaluate the strength properties of a particular metal from its stress-strain [(S1 - E1]) curve obtained by means of a conventional tension test. Such a stress-strain curve, Fig I, illustrates two important properties of a metal, its ability to strain harden, and its ability to withstand a certain limiting stress, the "fracture stress,"[ (s'r)], and a certain limiting strain, the "ductility" [(e1)], before it fails by separation. These two fracturing characteristics are the coordinates of the point of fracture in Fig I. In the case of a metal which necks in a tension test, both the fracture stress and the ductility (measured in a tension test) are dependent upon (a) the shape of the neck and (b) average values of the stresses and strains over the cross section at the moment of fracture. However, for the purpose of this investigation, these average quantities, rather than the actual values, may be considered for reasons of simplicity. It appears that the conclusions also hold true if the analysis were carried out for actual values of fracture stress and ductility at the locus of failure. In this paper, the effects of straining (at room temperature) by various methods on [ ] the above metal characteristics, which were determined by subsequent tension tests will be discussed. According to our present knowledge, any such prestraining results in a stress-strain curve (in subsequent testing by tension), Fig 2, the general shape, or flow characteristics, of which can be derived from the original stress-strain curve of the unstrained metal minus a certain portion exhausted by the initial straining. This phenomenon is called strain hardening, and may be measured by the magnitude of the cut-off, or the "effective strain," from which the new curve must start in order to coincide in its plastic branch with the original stress-strain curve.

Jan 1, 1948

By J. G. Mravec

The SO-called gas-tube method as developed by Hare, Peterson and Soler for determining the type and content of gases in molten steel is particularly adapted for determining the hydrogen content in molten steel. The development of this method has been quite completely discussed in a paper published by these co-workers in 1937.' The purpose of this paper, therefore, is to familiarize with this method those who arc not well acquainted with it. The principle of the gas-tube method is as fol1ows: One end of an evacuated gas tube is sealed with a very thin copper disk. when this end of the tube is immersed in a test spoonful of molten steel, the copper disk melts almost immediately, allowing a portion of the steel to be drawn up into the evacuated space. Any dissolved gases, and those produced by reactions between the components of the steel during freezing, are liberated into the unfilled portion of the sampling tube. A blob of steel that forms on the immersed end of the tube after the sample is drawn up seals up the end, making it airtight again. The evolved gases are subsequently drawn out of the gas tube through a suitable valve and analyzed by means of an Orsat apparatus. The volume of the sampling tube is sufficiently large so that a pressure considerably below atmospheric is produced after the gas evolution. The low pressure is necessary to effect a nearly complete removal of gases from the steel. Construction oF Sampling Tube The sampling gas-tube apparatus is illustrated in Fig. I. Seamless S.A.E. tubing used for section A is first cut into 7-ft. lengths. Through cxperiencc it was found necessary to use two sizes of tubing for this part, "is-in. and 3/4-in., respectively. The smaller tubing is generally used on the hotter or lower carbon steels. If the inside wall of the tube A is coated with grease or oil, it should be burned out before being machined as follows: One end is machined on the inside diameter to a depth of 34 in., so as to form a seat for a 7/8-in copper disk, which is stamped out from 0.005 to 0.007-in. thick copper sheet. The other end is machined on the outside diameter to a diameter of 1 5/16 in., to take a small reservoir or trap member I?. About 4 in. below the same end, a 1/2-in. hole is drilled to receive the 1/2-in. copper tubing leading to the large reservoir C. The inside of tube A is then thoroughly cleaned with a round wire brush, such as is generally used to clean out shotgun barrels. It is very important that the surface be absolutely free of rust or any nonmetallic coating. Next, the thin copper disk is soldered in place with low-melting silver solder.

Jan 1, 1945

By C. A. Heiland

The Eötvös torsion balance permits the measurement of certain second derivatives of the gravity-potential, which are known as the gradients of gravity and the curvature values for an equipotential plane of gravity. These quantities are influenced on level ground by the configuration of the masses underneath. Hence, the torsion balance has gained great importance for the location of geological structures and thus indirectly for the discovery of oil and other mineral deposits. If the ground is not level, however, the measurements become more difficult, because the superficial mass-irregularities also produce more or less considerable disturbances. It is necessary, therefore, to determine the shape of the surrounding topography by leveling as well as by consulting topographic maps and to compute its influence upon the torsion balance. The correction thus determined is called, in general, the topographic correction; it is composed of two constituents, the terrain correction and the cartographic correction. The terrain correction would be that part of the topographic correction as derived from the direct leveling of the area surrounding the station, whereas the data for the computation of the cartographic correction are obtained from a topographic map, usually beginning with a radius of LOO meters, as under most circumstances it is difficult to level along a arger concentric circle about the station. Principle of Topographic Correction The principle of all topographic corrections is to assume a homogene-ous compositon of the masses around the station in regard to specific gravity as well as a mathematical shape of the topography. The results become the more accurate the closer this mathematical shape is to the actual configuration of the terrain, but naturally the amount of necessary computation also increases. If a standard correction with fixed dis-ances is adopted, the middle error of this method will, therefore, increase as the irregularity of the terrain. Hence, the application of the torsion balance in mountainous areas may be successful only if the disturbances due to heavy masses underneath the surface are so large as to exceed onsiderably the increased middle error due to rugged topography, or,

Jan 1, 1929

By Benjamin Smith Lyman

THE importance of topography to geology is so commonly underrated as to deserve to be pointed out again and again. The relation of topography to the different branches of geology may be seen best by a glance at them all. Geology is well understood to consist of the observation of facts about rocks as materials of the earth (geognosy ), and the explanation of those facts (geogeny). The facts to observe are: I. GEOMETRICAL, as (1) structure, including the dip and strike at different points, the size, shape, and position of basins and saddles; (2) vertical section, that is, the thickness of rock groups and of their parts ; (3) horizontal or geographical position. II. PHYSICAL, such as texture, whether sedimentary or crystalline ; and, if crystalline, whether granitic, porphyritic, amygdaloidal, globular, or concretionary; whether compact or granular; coarse or fine; pervious or impervious; hard or soft; firm or tender; with cleavage or without; massive or thin; the microscopic structure; also whether magnetic or not; soluble or insoluble; fusible or infusible; and the constituent minerals. III. CHEMICAL, that is, the composition of the rocks and of their minerals and their affinities. IV. PALÆONTOLOGICAL, as what kind of fossils are in the rocks,

Jan 1, 1873

By R. Stanford

In any discussion of steel pouring too often refractories quality assumes a high level of importance. Unfortunately when one considers the many and varied conditions to which pouring refractories are exposed, it is difficult to isolate the true role of refractories quality alone. Some of the more important, yet often overlooked, variable conditions bearing on pouring performance are heat size, tap time and temperature, steel chemistry, ladle additions, ladle height and preheat, mechanical conditions of the pouring mechanism, hot top or non hot topped ingots and, ingot size, which determine total number of shutoffs, direct or tundish pouring, ingot filling rates, metallurgical demands, etc, etc. These considerations apply for either conventional or slide gate pouring of ingots and, to a large extent, even strand casting. In any event probably the most significant factor on pouring performance in any individual shop is what is considered an "OK" pour. We find considerable variance in this qualification, not only between Republic Steel meltshops, but throughout the industry. Therefore, it is a worthless exercise to draw comparisons attributable to refractories quality alone, except for similar conditions in a single shop.

Jan 1, 1972