Search Documents

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin: The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most promising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestetn Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1947

By Alexander Coucoulas

FABRICATION of thin-film circuits deposited on glass substrates requires the formation of permanent electrical contacts. Since thin films are in the order of a few thousand angstroms thick and are deposited on nonconductive surfaces such as glass, new methods of lead attachment are being pursued in the microelectronics industry. Ultrasonic welding is being considered in thin-film technology since joining can be accomplished between a wide variety of dissimilar materials.l,' Ultrasonic welding is accomplished by a transducer-coupling-tip system which converts high-frequency electrical energy into mechanical vibrations and delivers it into the weld region. During the process the tip oscillates in a direction parallel to the surface of the weldments, inducing shear stresses in the work pieces which are clamped between the tip and anvil. Though the basic bonding mechanism is not clearly understood, it has been described as closely akin to friction welding. In the course of an investigation concerned with ultrasonic we!ding of aluminum wires to tantalum thin films (1400A) deposited on glass, low weld strengths were related to glass failure. Upon investigating this condition, an improved method of bonding was developed where the aluminum was held at a temperature where a minimum amount of strain hardening occurred during the introduction of ultrasonic energy. Experimental Procedure. Aluminum wires (0.015 in,) were bonded to tantalum thin films with an optimized set of welding parameters (power, time, clamping force) employing a commercial 100-w 60-kc ultrasonic welder. Forty-five degree shear-peel tests, where the lead is pulled at a 45-deg angle with respect to the substrate at 0.2 in. per min, produced a large variation from zero to the strength of the wire, Table I. Inspection of the weld region generally revealed: glass cracking before and after testing; the removal of glass nuggets from the substrate by the lead during testing, Table I; thin-film penetration. In an effort to improve the shear-peel strength, the aluminum between the tip and substrate was heated above ambient temperature through an argon gas media prior to and during welding with the same parameters employed above. With the addition of heat: wire deformation was increased; shear-peel tests all failed at the weld-wire junction, leaving the bonded portion undisturbed; no evidence of glass cracking or film penetration prior to or after testing was observed. In order to prevent failure at the weld-wire junction due to excessive wire deformation, 0.035-in. aluminum wires were welded to tantalum thin films with an optimized set of welding and heating parameters. As

Jan 1, 1967

By T. A. Rickard

INTRODUCTORY. THE presentation to the Institute, eight years ago, of the paper of Pošepny on " The Genesis of Ore-Deposits " has borne fruit in much fresh: investigation, as is evidenced, for example, by the group of very valuable papers, by distinguished members" of the United States Geological Survey, read at the Washington meeting-discussions of general principles particularly suggestive to those who are engaged in mining. Pošepny, in the discussion of his famous treatise, said that the present writer seemed to look at every new conception in ore-deposition" from the sole standpoint of its immediate usefulness in mining."* Protesting mildly against " sole " and "immediate," I accept the impeachment. It calls for no defence. THE DEVELOPMENT OF RECENT THEORIES. Given the idea of an underground water-circulation as the chief factor in the deposition of ore, the next step in the inquiry as to the genesis of such deposits is, the endeavor to determine which particular part of the general water-circulation is responsible for the results. Around this question have centered the controversies of a generation, and to these controversies we owe the gradual clarification of our ideas upon the processes of ore-formation. It is unnecessary to sketch here their progress from Werner to Le Conte, who combated in 1883 the extreme views of the lateral-seeretionists, and in 1893 opposed the narrow interpretation of the ascensionist-theory. The generally accepted opinions of to-day are a well-deserved tribute to his philosophic discrimination. Thanks to Prof. Van Hise and Mr. Slichter, whose work he utilizes, we have now arrived at a comprehensive conception

Jan 1, 1902

By John H. Hollomon

In a recent paper,' a very early suggestion by Ludwik2 concerning the nature of the mechanical behavior of metals has becn reexamined and extended. In essence it was suggested that there exists, at least under certain conditions, a mechanical equation of state; that the stress required for flow depends upon the instantaneous values of the strain, strain rate, and temperature, and not upon their past values. It is proposed that under these circumstances thc stress does not depend upon past history of these variables, but is like the temperature of a gas that depends only upon the instantaneous values of the pressure and volume. This notion has not been applied to present-day studies of metals, though it is especially applicable to the study of creep. It is the purpose of this paper to analyze the significance and possible range of applicability of this idea and to determine how it influences the accepted ideas concerning creep. Stress-strain Relations It is wcll known that the stress-strain curves of metals are influenced by both train rate and temperature. For a fixed strain rate and temperature there is associated with each metal a stress-strain curve. If either the strain rate or temperature is changed a new stress-strain curve will be characteristic (Fig. I). A much more genera1 relation between the effects of these variables is possible, however. Consider the stress-strain curves of Fig. I determined at

Jan 1, 1947

By John H. Hollomon

In a recent paper,' a very early suggestion by Ludwik2 concerning the nature of the mechanical behavior of metals has becn reexamined and extended. In essence it was suggested that there exists, at least under certain conditions, a mechanical equation of state; that the stress required for flow depends upon the instantaneous values of the strain, strain rate, and temperature, and not upon their past values. It is proposed that under these circumstances thc stress does not depend upon past history of these variables, but is like the temperature of a gas that depends only upon the instantaneous values of the pressure and volume. This notion has not been applied to present-day studies of metals, though it is especially applicable to the study of creep. It is the purpose of this paper to analyze the significance and possible range of applicability of this idea and to determine how it influences the accepted ideas concerning creep. Stress-strain Relations It is wcll known that the stress-strain curves of metals are influenced by both train rate and temperature. For a fixed strain rate and temperature there is associated with each metal a stress-strain curve. If either the strain rate or temperature is changed a new stress-strain curve will be characteristic (Fig. I). A much more genera1 relation between the effects of these variables is possible, however. Consider the stress-strain curves of Fig. I determined at

Jan 1, 1947

By J. S. Marsh

OPPORTUNITY to pay tribute to the memory of Professor Henry Marion Howe is a strenuous assignment as well as an honor. Upon recalling Howe lecturers and lectures of the past 25 years, glancing over the list of those earlier, and rereading Howe's books, I arrive at several conclusions: 1—Many lecturers either worked under or knew Professor Howe. 2—It is virtually impossible to pick a subject on which Professor Howe did not touch. 3—There is precedent for a technical paper based upon pursuit of a single subject. 4—There have been listening lectures and reading lectures. There is solid comfort only in 2: the subject field is wide open. I did not know, nor even ever saw, Professor Howe, so can supply no fitting reminiscence. As a college student I was dimly aware that he counted among the giants. Fuller appreciation of his stature came with reading his books and papers, growing acquaintance with some of his associates, and the intrinsic dignity of the climax of the Annual Meeting, beginning at four o'clock of a Thursday afternoon in the auditorium of the Engineering Societies Building in New York. As for producing the technical paper sort of thing, it is my lot to have reached an age and assignment such that to do so would be to filch information from those who did the work and whose story is theirs to tell; for this I have no enthusiasm. As for the final conclusion, Professor Howe was one of the chosen few so highly expert at expository writing that he could produce a lecture or paper that reads as though it would also have listened well. One of his tricks was the free use of words not ordinarily part of the technical vocabulary, provided that such words were likely to communicate most precisely what he had in mind. How wonderful it would be for all who must read reports by the ton if ability at exposition could be taught with the effectiveness open, say to, differential calculus! Perhaps Professor Howe should be required college reading even if for no other reason than to prove that technical writing need be neither dull nor diffuse. My assignment is clearly still strenuous. Another point to consider is the fact that metallurgy is now so tremendously diversified that hope of finding a topic of universal appeal is negligible, even if one were competent enough to be permitted free choice. That which follows is, therefore, a compromise composed of necessity and of the obligation to attempt to avoid boring to slumber those of you who are not especially interested in the general subject chosen. The Iron and Steel Div. is now essentially a process metallurgy division, heavily concerned with the smelting of iron and the making of steel. The American Iron and Steel Inst. figure for present steel capacity of this country is 125,828,310 net tons; how this is divided among processes is indicated by the production totals for 1953, shown in Table I. The glamor girls and boys make the front page and so it is with steelmaking processes. If there is an Antarctic Daily Bugle, it undoubtedly has carried stories of revolutionary development, such as oxygen processes and vacuum melting, and stories of the incomparably rosy destiny of electric arc melting. All such certainly have their place and their future; meanwhile, it is the sturdy and old reliable open hearth that accounts for the bulk of production reported back on the financial page, and it is the old reliable that is most likely to continue to account for the bulk for some perfectly sound raw material, technologic, and economic reasons. This, plus the fact that next year marks a centennial (for it was in 1856 that Frederick and William Siemens conceived the regenerative open hearth), is reason enough to talk about open hearth furnaces, but is not the real one. The real reason is that in some years of association with open hearths, I have accumulated—in addition to a genuine liking and respect for them—certain odds and ends of fact and fancy that this lecture provides a unique chance

Jan 1, 1956

By Georges Ranque

THIS paper by. Georges Ranque is an attempt to reason out the conditions of formation and stability of inclusions and to establish an operative process capable of eliminating or minimizing them. The paper consists of two parts; one in which the author considers the laws of physical chemistry and physics that apply to liquid slag-metal systems and one in which he describes a practice based on the theoretical considerations. Such a paper is bound to contain controversial points and it is therefore your speaker's intention to present Mr. Ranque's side of the picture to the best of his ability without regard for any thoughts or criticisms of his own. RISING VELOCITIES OF INCLUSIONS Most nonmetallic inclusions have densities ranging from about 1.7 to s, while liquid steel has a density of about 7. Under these conditions, ferrostatic pressure should cause the inclusions, being lighter, to rise from the bath and be eliminated. This rising tendency is expressed by Stokes' law, from which may be calculated the rising velocity of a spherical particle in a liquid medium whose density and viscosity are known.

Jan 1, 1947

America.-Foreman, J. T. Ashland.-Sturdevant, J. C. AItalIa. Henderson, R. M. Bessemer.-Ball, E. M. Maschmeyer, W. L. McKenzie, W. C., Jr. Birmingham.-Abbott, C. E. Aldrich, T. H. Aldrich, T. H., Jr Aufderhaar, H. C. Berg, H. A. Blair, C. S. Bush, M. W. Clark, G. H.

Jan 1, 1923

By Anwar-ul Karim

In one of our recent papers, Cheng, Karim, Langdon, and Dom1 analyzed the creep mechanisms in a Fe-4 pct Si alloy. The experimental results of apparent ac-

Jan 1, 1970

By Walther Mathesus

INTRODUCTION THE use of high blast heats on furnaces melting Mesaba ores is still the exception, the average blast temperatures carried on Mesaba stacks seldom reaching 1,100° F. Some 15 years ago, when the use of fine Mesaba ores in larger proportions to the total burden first came into practice, it was found difficult to employ even those blast heats which it had been possible to carry with the Old Range ores. The furnaces refused to "take" high heats, and would persistently labor with irregular stock movement, which impaired the practice and increased the coke consumption. By lowering the blast temperature, the working of the furnace became smoother, and experience taught that with the softer and more easily reduced Mesaba ores, satisfactory practice could be obtained with comparatively low blast heats. Therefore a large number of Mesaba furnaces have ever since been operated on very low blast temperatures, ranging between 800° and 1,000° F. In the face of these difficulties, furnace men were slow to recognize that furnaces could be so designed as to permit a free movement of the charges in combination with the use of higher heats. Since higher blast temperatures did not seem to offer great advantages in the smelting of Mesaba ores, investments in hot-blast stoves were not as attractive to the furnace man as labor-saving devices and means of obtaining greater tonnages. The effect of this preference is keenly felt at the present time. It has brought about the peculiar situation, that the majority of our furnace plants (among them some of the most progressive) lack modern and efficient stove equipment. The result is that, even where the proper furnace lines have been adopted and conditions are now favorable to the successful employment of higher blast temperatures, the heats required for the greatest fuel economy are not available.

Jan 3, 1915

By H. M. Roberts

H. M. ROBERTS, Minneapolis, Minn. (communication to the Secretary*). -The rifling of drill cores is a frequent source of interest to men engaged in diamond drilling. Previous to the appearance of Dr. Crane's paper, there has been little record of connected observation or rigid speculation as applied to the cause of rifling. Replying to one of Dr. Crane's letters of inquiry, I ventured my opinion that the cause of rifling was a complex problem in physics, which I had not attempted to solve up to that time, except to ascribe it to the general cause of rotation and vibration of the rods. The question is worth attention not only as a matter of curious scientific interest but also for the reason that it stimulates thought on

Jan 10, 1916

By Sidney Powers, Alfred C. Lane

This paper aims to present the results of an investigation concerning gravitative differentiation in lava flows, based on a quantitative microscopic and chemical study of a Triassic basalt from Nova Scotia, and confirmed by data secured from a study of certain Keweenawan ophites. At Cape d'Or, Nova Scotia, near the head of the Bay of Bundy, marine erosion has exposed a series of Triassic basalt flows in which copper has been sought for a number of years. Studies of the thickest flow of the series with regard to volumetric composition, specific gravity, and grain have been made by the junior author, and measurements by students at Tufts College, together with confirmatory observations of the same nature on this and other flows by the senior writer, and chemical analyses made by the Division of Chemistry, Mines Branch, Ottawa,' all show differentiation in lava flows comparable to that in intrusive bodies. The work was made possible by the availability of the drill-cores, the property of Tufts College, and emphasizes the desirability of the study of drill-cores from other localities. Measurements of the specific gravities of certain Keweenawan lava flows of Michigan by the senior author, from material collected in 1915, will be given as a comparison to those of the Cape d'Or flow. It has been found that the specific gravity of drill-cores, or volume per cubic foot, can be readily obtained by measuring their dimensions. This can be done to an accuracy of within 1 per cent. in pieces of core over 100 mm. in length by using a micrometer gage for the diameter, and taking the average of six measurements of the diameter; and the average of four measurements of the length made with a finely graduated ruler. Then, after weighing them, the weight in grams per cubic centimeter, or what is practically the same thing, ounces per cubic foot, is obtained. System-

Jan 1, 1916

By Quentin Singewald

SOME of the broader relations between structure and ore deposition along the London fault, deduced from a thorough study of the geology of the eastern part of the Mosquito Range, should be of general interest to economic geologists. The first part of this paper is a generalized state-ment of the geology of the region in which the London fault is located; it may be supplemented by reference to several earlier publications by the writers and to the U. S. Geological Survey's Professional Paper 148, on the Leadville district. The second part deals with the structure of both the fault and the disturbed zone adjoining the fault. The third part dis-cusses the salient features of the ore deposits, particularly emphasizing structural control. The two generalized maps are complementary to one another but contain too many data to show on a single small map. The London fault is between Leadville and Alma, and the ore deposits along it are said to lie in the Alma district. Field work in this district, during six summers since 1927, has been a part of the cooperative work of the U. S. Geological Survey, the State of Colorado, and the Colorado Metal Mining Board. The writers have made use of work by R. D. Butler, J. W. Vanderwilt and R. E. Landon. G. F. Loughlin and C. H. Behre, Jr., who have worked on the west side of the range, have con-tributed valuable suggestions. Mining men of the district have aided in many ways.

Jan 1, 1936

By G. F. Jenkins

The word asbestos is a broad term that has been accepted and applied to a number of fibrous mineral silicates found in nature. They are incombustible and can be separated by mechanical means into fibers of various lengths and thicknesses, but differ in chemical composition and other properties. It is generally recognized that there are six varieties of asbestos; the finely fibrous form of serpentine known as chrysotile, and five minerals of the amphibole group, i.e., amosite (not fully recognized as a mineral species name but accepted in asbestos terminology), anthophyllite, crocidolite, tremolite and actinolite. (Figs 1-4.) Physical and Other Properties The structures of asbestos fibers have been studied intensely in recent years. X-ray diffraction patterns 1 to 15 have been used as a means of identification and classification. The amphibole group structures have been fairly well established while the serpentine group has been the subject of many investigations during the past six years. Low-angle X-ray scattering techniques5 have shown that the chrysotile fibrils are "hexagonally close packed" and parallel to each other, having cross-sectional diameters varying from 180Å* units to 300Å units, while the amphibole fibers are many times larger in cross section. The electron micrographs of chrysotile asbestos (Figs 1-4) have also indicated that the fibrils might be in the form of a hollow tube. This point has been the subject of considerable controversy by a number of investigators.7 to 16 Density measurements17 made on a sample of high quality Arizona fiber did not indicate that the fiber had a hollow tube structure; however, the so-called "sheet structure" of the fibril could be distorted in such a way that it gives the appearance of a hollow tube in the electron microscope. It is of interest to quote one investigator, F. L. Pundsack,17 in this connection: Although the empirical composition of chrysotile is 3MgO.2SiO2.2H20, the true unit cell[#] composition is best represented as Mg12(OH)16Si8O20. This cell has dimensions of a= 5.3Å, b = 9.2 Å, and c = 14.6 Å where the "a" direction is the fiber axis. The calculated density of this unit is 2.56 g/cc, a value in close agreement with experimentally determined density values for chrysotile. The exact manner in which the unit cells of asbestos are stacked together to build up a single fiber of chrysotile is not known, but from various

Jan 1, 1960

By Burton H. Boyum

GREATER depth of exploration drill holes and increasing cost of drilling have been principal factors in reviving interest on the Marquette Iron Range in controlled directional drill-hole deflection. This deflection is obtained by the application of the Hall-Row wedging technique. Modifications were made in the technique and equipment in the effort to simplify and strengthen the procedure. The practice is similar in many respects to the oil well type of deflection with a whipstock.

Jan 1, 1947

By C. S. Barrett

WhEN a collimated beam of protons or other energetic particles is scattered by a single crystal, the emerging particles produce patterns that contain much crystallographic information. Calculations of the trajectories of individual particles can predict with reasonable accuracy the complete pattern (which is related reciprocally to channeling, now studied in detail6) but the task is a lengthy one which has been completed for very few cases. A many-beam dynamic diffraction calculation of the patterns would be even more difficult and in some cases may be invalid. Because of these complexities, simple methods that will predict to a rough approximation the relative intensities of the lines in films of the back-scattering patterns of a given crystal are wanted. I have found a method which, although it is not a valid computation of intensities or of film darkening by either dynamic or kinematic diffraction principles or by trajectory calculations, nevertheless is found to be useful in practice. It has been tested on several crystal types,7 and is here tested on additional ones. The method consists in first calculating the structure factor F(hk1) for the (hkl) plane, of spacing d, by the familiar equation: where the summation extends over the atoms in the unit cell and fj is the atom scattering factor of the jth atom (using tables computed for electron diffraction, preferably those computed without exchange). Then the F values are squared and summed over all the orders, n, for which F2 has an appreciable value, giving a quantity: Finally, I, is expressed as a percentage of Ic for the

Jan 1, 1970

By Frederic Lahee

THE purpose of this paper is to demonstrate the similarity of the oil-producing structures in the Mexia1 fault zone, and to show how the apparently very irregular well logs in these fields may be used for the practical interpretation of subsurface conditions. The Mexia oil field, in Limestone County, Tex. (Fig. 1) is closely associated with a fault that trends about 30° east of north and has a displacement of between 200 and 400 ft., with downthrow on the west. Minor slips accompany this major fault, some being roughly parallel to the main break while others are transverse to it. These faults belong to the so-called Mexia fault zone, a belt of fracturing that has been traced in its characteristic features southward to near Kosse, 15 miles south of Groesbeck, in southern Limestone County, and northward at least as far as the Trinity river at the eastern border of Navarro County, and possibly as far north as Hunt and Hopkins counties.2 The Balcones fault zone, from 30 to 40 miles west of the Mexia fault zone, differs from the latter in that its principal displacement is a down-throw on the east. In this respect, it is exactly the opposite of the Mexia displacement. Between these two zones of major faulting lies a great down-dropped block, or graben, which is broken by numerous minor faults.

Jan 2, 1925

By Will H. Coghill, P. H. Delano, G. D. Coe

DATA concerning the actual net energy required for pulverizing coal are lacking from the literature on coal pulverization. Power data given in the literature concern gross power and frequently include the power expended on the air blast or product-conveyor system, as well as power lost through friction in the pulverizer itself. Consequently, such data supply no information regarding the net energy consumed in pulverizing or the relative grinding resistance of various coals. In the study of coal pulverizing much work has been done on what is known as "grindability-index numbers," but grindability tests have seldom considered the energy input (that is, the "cause" part of the system "cause and effect"). There are many records of the effect, but even these have questionable value because the "grindability" tests did not make a pulverized product by a method comparable with commercial pulverizers. In many of the tests, only a selected part of the coal was ground, and the remainder continued to be an unknown factor. Furthermore, none of the grindability tests provide the balanced circulating load common to all modern commercial pulverizing. In order to obtain better understanding of the fundamental principles of coal pulverizing, the Bureau of Mines is investigating the "cause" phase; that is, the net energy input or net power excluding friction between the moving parts of the machine. As a first step in the investigation, it was necessary to design and construct a laboratory machine in which no friction-loss corrections are involved, which could grind and finish a minus-3/4 -inch feed, which could be emptied rapidly and completely, which could operate with a continuous feed and finish in an air separator; and, most essential of all, which would be equipped with a measuring device for recording only that portion of the total power consumed in actual pulverizing, hereafter referred to as "net energy input" or "net horse-powerhours." The channel-roller pulverizer here-inafter described is believed to meet these requirements. HISTORY OF THE MACHINE The work started when Ralph W. Smith, engineer, St. Genevieve Lime Co., St. Genevieve, Mo., was appointed one of the consultants of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, to develop a machine for testing the abrasiveness of coal. Smith had already developed a machine for testing the abrasiveness of dentifrices,1 and it was thought the same principles might be applied to coal. Smith's machine had a revolving disk with an annular channel in which the sample was placed. Riding in the channel was a small block or runner of selected soft metal held

Jan 1, 1942

By Theodore Simons

(Butte Meeting, August, 1913.) DURING the last half century a great amount of ingenuity and energy has been devoted to the invention of appliances for the recovery of valuable minerals from very fine sands and slimes. The reason for this is that in almost every dressing plant the greatest losses of values, considered relatively as well as absolutely, occur in the treatment of slimes. The natural aim of mill operators to minimize these losses has in recent years received another impetus, from the fact that the gradually diminishing occurrence of high-grade ores makes a more intense recovery of values from existing resources absolutely necessary for profitable operation. The results of such attempts are found in the appearance of a great number of machines and appliances which make it profitable to-clay to rework old dumps, containing the tailings of older processes. A constantly growing difficulty of obtaining skilled labor and the increase in wages made it prohibitory to employ those types of machines which required much attention, and in the middle of the nineteenth century the various concentrating tables of the percussion type, which automatically discharge their products, began to take the place of the intermittent tables, on which, when the bed had reached a certain thickness, operation had to be stopped in order to allow the skimming by hand of the separate layers formed on the table. In the course of years, two general types of machines evolved for the treatment of fine sands and slimes : The so-called concentrators and vanners, on the one hand, and the buddies and round tables on the other.1 For the profitable treatment of the very finest slimes, round tables have as a last resort proved more satisfactory and economical than other machines.

Jan 7, 1913

By David White

In these days, when detailed investigations of stratigraphy, structure, and sand conditions so frequently result in the discovery of new oil fields, and applause from oil companies and the public, geologists do well to walk humbly, and punctiliously to admit that the geologic principles controlling the distribution of oil and gas have as yet been discovered only in part, and that what remains yet to be learned is probably vastly more than what is already known. The few experiments already attempted have been fragmentary, and somewhat desultory, and however positive each of us may be with respect to certain theoretical conclusions, many of the fundamental questions as to the origin and mode of occurrence of petroleum are subject to radical disagreement. Of the chemical changes attending the generation of petroleum from organic matter, little is actually known. Most of the postulated formulas are liable to be misleading, through ignorance of essential factors. Open-minded-ness is therefore a prime essential at the present stage of our science. Nevertheless, adopting the hypothesis that oil originates in some manner fundamentally connected with the organic theory, and in possible departure from such open-mindedness, the writer will pay no attention to the so-called inorganic theory, since every attempt to apply this theory to the study of old oil fields, or to the discovery of new ones, affords cumulative evidence of its inadequacy. In this paper, some of the factors affecting the occurrence of petroleum that the writer believes worthy of consideration by the prospector for oil in any new region will be discussed. Some of these, which arc less generaLly understood, will be considercd somewhat in detail. Other points, the significance of which cannot now be determined, require more field study, and for that reason are here brought to the attention of the field geologist. On the other hand, certain theoretical points which do not bear especially on the oil possibilities of a new region will be given little or no attention. The main topics that will be discussed are: (1) sufficiency of carbonaceous detritus and residues in the oil-forming rocks; (2) stage of carbonization of the organic matter in the oil-bearing formations; (3) folding of the strata; (4) thickness of sedimentary formations; (5) conditions of deposition.

Jan 1, 1921