Search Documents

Jan 1, 1970

By E. O. Chartkoff

IN 1926 one of the authors published researches on the determination and description of the iron-tungsten and iron-molybdenum systems,1 including the equilibrium diagrams. In 1929, further work was carried on, including the examination by X-rays, which is recorded here. Measurements were made of changes in lattice parameters in the solid solutions. Precipitation from the solid solution and the accompanying changes in hardness were studied as well as the formation of the intermetallic compound phases upon sintering a mixture of metal powders.

Jan 1, 1930

By W. R. Atkins

THE Negaunee mine is at the east end of the Marquette Range, in the city of Negaunee, on the Upper Peninsula of Michigan. Iron ore was first discovered on this property in 1883 by diamond drilling. A shaft was sunk soon afterward, and the mine has been worked continuously ever since. The total shipments from 1887 to' Jan. 1, 1945, were 20,417,587 long tons. The mine was taken over by the present operators, The Cleveland-Cliffs Iron Co., in 1903. During the past four years, 1941 to 1944 inclusive, the property has produced an average of nearly a million tons a year, and has employed more than 400 men. GEOLOGY The ore body at the Negaunee mine lies in a large syncline dipping about 15° to the west, the ore coming to ledge at the east end of the trough. The ore occurs in the Negaunee formation of the middle Huronian age, which consists of ferruginous cherts and slates through which intrusions of diorite have occurred. Although these intrusions of diorite have an important bearing on the formation of ore on the range, they are not important in this ore body. Some faulting has taken place along the diorite intrusions, or dikes as they are called locally, and also other faults are known to exist across the formation. These faults do not complicate either mining or development of the ore body. The footwall consists of jasper underlain with Siamo slate; the hanging wall is jasper and ferruginous chert. Fig. I shows a typical cross section of the ore body. The ore body is quite regular, about 120 ft. thick in the middle of the syncline and thinning out toward both sides of the fold. Its width ranges from 400 to 800 ft., the average being about 600 ft. The footwall is uniform in dip and strike, but irregular lenses of ore often extend 50 to 75 ft. up into the overlying jasper capping. METHOD OF MINING Ore in the Negaunee mine has been mined by top slicing almost exclusively since 1903. This method of mining has been employed because it is especially adapted to the size and shape of the Negaunee ore body, and to the soft, sticky nature of the ore as well as the generally soft, broken jasper capping. Development The ore body has been developed from six different levels with intervals varying between l00 and 125 ft. On the average, the dip causes a horizontal offset of 350 ft. per level, and under these circumstances it has been necessary to carry on considerable development in rock to make available the ore lying along the north and east footwalls. This is not as disadvantageous as might be supposed, because of reduced pressure and the accompanying saving in maintenance costs. The development of the

Jan 1, 1946

By Philip Wilson

THE Province of British Columbia covers 382,000 sq. mi., about 250,000 sq. mi. of which have not been prospected. In fact, the coast country and the islands are so heavily timbered and the surface covered with so thick a mantle of soil, muskeg, and, over broad areas, glacial drift, that prospecting, and even trail breaking are extremely difficult. It is only along the coast or stream channels, or above the timber line, or where snow or rock slides have scoured the surface that rock outcrops can be found. Glaciers nestle in many of the cirques and fill the valleys in the higher ranges. Great ice sheets and perpetual snow persist in certain localities, thus reducing the exposed areas worth prospecting. Almost the entire country has been subjected to intense glaciation, so that the conspicuous oxidized outcrops of orebodies typical of the south-western United States and Mexico do not exist and surface bodies of enriched or oxidized ore are rare. With few exceptions, the mines1 of the Province are working primary ore. Developments have proved that some of these orebodies are large and important, although usually comparatively low in grade. Besides the few mines that have produced most of the minerals, there are many small mines, but their total output is unimportant. Considering the number of mines and prospects and the widespread mineralization, it is strange that no really great mines, comparable in size and richness with those in the western United States have been found.

Jan 8, 1922

By H. J. Hand

STATISTICAL methods are becoming increasingly important for inter-preting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor,1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.-Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of vari-ables more or less constantly tending to affect it. As pointed out by Daeves, 2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such plants. ?

Jan 1, 1938

By R. H. Wightman

THE following paper describes current mining practices of the Riverside Cement Co. at its Crestmore plant, Riverside, California. For a number of years the Riverside Cement Co. obtained its raw materials by surface quarry operations but after these deposits were exhausted for equipment available at that time, the company started underground mining. Mine workings were begun in 1927 to 1930 for the recovery of limestone by block-caving methods. GEOLOGY The bed of limestone that is being worked is a metamorphosed and recrystallized limestone, which is generally white in color and from medium to coarsely crystalline. This bed is fissured by water courses that vary from minute cracks to large areas. The bed has also been cracked by intrusions along the footwall and hanging wall. These walls are coarse-grained, gray, quartz granodiorite. The strike of the deposit is north and south and it dips to the east at an angle of approximately 50º. The bed is approximately 1700 ft. long, 270 ft. thick at right angles to the dip at the middle of the deposit and tapers to a thickness of approximately 100 ft. at each end. MINING METHODS The mine layout consists of four main levels with elevations as follows: 892 Collar of shaft. 800 Manway level used for ventilation, prospect purposes and as an entrance into the stopes. 700 Mining level where all material is extracted and on which are located the tapping grizzlies. This is the elevation from which all main cutoff stopes and undercutting work is started. 660 Haulage level where the limestone is drawn from transfer raises into the cars and is transported to the tipple by electric locomotives. 633 Level where all water is collected and which keeps the general water table below the working levels. A detailed description of the mine was given in U. S. Bureau of Mines Information Circular No. 6795, in June 1934. Current Block Development The first blocks to be caved were developed very much after the procedure followed in the copper mines of Arizona. This paper covers the ninth block to be caved. With a hard, tough rock like our limestone, it was found that some alterations in the development and control of draw in caving were necessary to secure better crushing effect and provide more safety for such secondary blasting as is required. Sequence of Block Development I. The fringes of the 800-ft. manway level are driven to confirm the diamond drill information and serve to determine the final location and development required for the block (Fig. I).

Jan 1, 1944

By H. Le Chatelier

SILICA brick are indispensable in the manufacture of steel because they alone are able to withstand the high temperature of regenerative furnaces. All attempts to replace silica brick by other refractory materials for this purpose have failed, but the reason for this failure has remained obscure; we shall give an explanation later in this paper. Before the war, silica brick employed in France came principally from abroad, for which reason, since the beginning of hostilities, certain French steel works have been seriously handicapped. Our attention was first directed to the question by M. Bred, Engineer of the Teil Works. With him, we began certain investigations, at first using our laboratory and the furnaces of neighboring steel works. The larger part of our experiments, however, have been made in the laboratory of the Faculty of Sciences at the Sorbonne. For the heating of our samples, we are deeply obliged to MM. Charpy, Yeatmann and Guérineau. In undertaking these studies, our first aim has been to render assistance to French industry, by indicating, as precisely as possible, the necessary conditions for the manufacture of high-grade brick; but at the same time we have intended to give an example of the manner in which scientific methods may be put to practical application in the solution of industrial problems. Although our work has been confined to samples of only a few grams, we are nevertheless convinced that our information can be directly utilized by brick-works of which the output is measured in thousands of tons

Jan 9, 1918

By C. C. Miller, C. A. Hutchinson, A. B. Dyes

This paper presents a simple and practical method for the estimation of effective permeability and reservoir pressures from the rise in bottom hole pressure when a well is shut in. The equations on which the method is based consider a stabilized well producing from a uniform formation when flow is shut off at the sand face followed by the unsteady state flow of a compressible liquid from regions far from a well to points closer in during the build-up period. An approximation for extending the method for two-phase flow in the reservoir is also presented. In order to compare the effects of extremes in the conditions existing at the external boundary of the reservoir, two general equations defining the build-up characteristics of the reservoir are shown: first, for a reservoir with constant pressure maintained at the radius of drainage, and second, for a reservoir with no influx over the radius of drainage. These equations define the build-up characteristics for the shut-in well as functions of time, the permeability and porosity of the drainage area, the viscosity and compressibility of the fluid flowing, the production rate prior to shut-in, and the radius of drainage of the well. When a well is shut in at the surface, rather than at the sand face, flow will continue into the well bore after shut-in due to the compressibility of the fluids in the bore. The effect upon the build-up characteristics of this flow into the well after shut-in has been studied by means of the electrical analyzer. From the basic relationships and consideration of the limitations due to continued flow after shut-in, methods have been developed for the estimation of the effective permeability of an area from the plot of the build-up characteristics of the well producing that area. Likewise, equations are presented for the estimation of the reservoir pressure from an early portion of the build-up curve. By means of the electrical analyzer, studies have been made concerning the variations in the build-up characteristics resulting from damaged or improved permeability in the immediate vicinity of the well bore. These studies show that the permeability estimated from the build-up curves represents the average effective permeability of the majority of the drainage area and that the permeability in the immediate vicinity of the well does not affect this estimate. Since the major portion of the drawdown is in the immediate vicinity of the well, variations in the permeability of this area greatly affect the productivity of the well as expressed by the productivity index. From pressure build-up and productivity index tests the ratio of the permeability of some arbitrarily specified area immediately surrounding the well and the effective permeability in the majority of the drainage area can be computed. This ratio is a measure of any damage to the well incurred in drilling or reworking and likewise any benefits as a result of remedial measures. In build-up tests and many other tests that are made on a producing well it is at least desirable, if not absolutely necessary, that the well be stabilized prior to testing. A method is presented here for relating the time required to stabilize a well and the reservoir and fluid properties. An equation is also presented for approximation of the length of shut-in time required to obtain sufficient build-up data for the estimation of permeability and reservoir pressure.

Jan 1, 1950

By George A. Moore, Donald P. Smith

In spite of many investigations of the occlusion of hydrogen in iron, the nature of the process and the reasons for the accompanying effects upon the metal are still open questions. This is in large part due to three causes: (1) the difficulty of obtaining iron of adequate purity as starting material; (2) the occurrence of allotropic transformations, which complicate the effects; and (3) the fact that the body-centered cubic modification does not lend itself readily to crystallographic investigation. The present paper attempts a critical review and correlation of the somewhat scattered and disconnected existing observations, and an experimental determination of the extent to which the conclusions that appear to follow from these are applicable to iron of really high purity, studied under well-defined conditions. Review Although only a comparatively few investigations have so far been made on the pure system iron-hydrogen, there is a much larger volume of literature which throws some light on the problem but falls short of a place in the systematic investigations, either because no attempt was made to measure equilibrium conditions or because the metal used was not iron or the gas not pure hydrogen. Such results have been variously dismissed in the past as of no importance, or as too complicated to try to explain; or they have been explained in terms of any of a dozen or more pictures, each of which is contradicted by data from other sources. The present importance of these data thus arises from their very mass and diversity, which present a picture of occlusion as a phenomenon whose variability cannot be ignored. We have attempted to organize the literature into groups comprising similar experiments or data leading to similar conclusions, thus of necessity sacrificing accuracy of historical order. Lattice Occlusion.—Throughout this discussion, the term "lattice occlusion" will be used to denote the formation of a simple solid solution of a gas in a metal lattice, usually of interstitial distribution. The word

Jan 1, 1939

By George A. Moore, Donald P. Smith

In spite of many investigations of the occlusion of hydrogen in iron, the nature of the process and the reasons for the accompanying effects upon the metal are still open questions. This is in large part due to three causes: (1) the difficulty of obtaining iron of adequate purity as starting material; (2) the occurrence of allotropic transformations, which complicate the effects; and (3) the fact that the body-centered cubic modification does not lend itself readily to crystallographic investigation. The present paper attempts a critical review and correlation of the somewhat scattered and disconnected existing observations, and an experimental determination of the extent to which the conclusions that appear to follow from these are applicable to iron of really high purity, studied under well-defined conditions. Review Although only a comparatively few investigations have so far been made on the pure system iron-hydrogen, there is a much larger volume of literature which throws some light on the problem but falls short of a place in the systematic investigations, either because no attempt was made to measure equilibrium conditions or because the metal used was not iron or the gas not pure hydrogen. Such results have been variously dismissed in the past as of no importance, or as too complicated to try to explain; or they have been explained in terms of any of a dozen or more pictures, each of which is contradicted by data from other sources. The present importance of these data thus arises from their very mass and diversity, which present a picture of occlusion as a phenomenon whose variability cannot be ignored. We have attempted to organize the literature into groups comprising similar experiments or data leading to similar conclusions, thus of necessity sacrificing accuracy of historical order. Lattice Occlusion.—Throughout this discussion, the term "lattice occlusion" will be used to denote the formation of a simple solid solution of a gas in a metal lattice, usually of interstitial distribution. The word

Jan 1, 1939

By Akio Suzuki, P. G. Wahlbeck

AS a part of a study of the vaporization of transition metal-chalcogen systems, the vaporization reactions for the Ti-Se system have been studied. In order to establish vaporization reactions it is important to determine the identity of vapor species in equilibrium with the condensed phases. In some cases, it is possible to deduce the identity of vapor species through observations of composition change of the condensed phase with which the vapor is in equilibrium. Determination of vapor species in equilibrium with condensed phases should precede vapor-pressure measurements and is necessary for proper thermodynamic analysis of vapor-pressure data. Bear and McTag-gart' reported that vacuum heating ot TiSea at 950°C produced a residue with a composition of 1.7 Se/Ti atomic ratio units. Analyses of condensed phases existing for the Ti-Se system have been performed by Bernusset,2"4 Gron-vold and Langmyhr,5 Hahn and Ness,' and Ehrlich.~ Results and conclusions of two types of experiments are described herein: 1) experiments where samples of known composition were vaporized followed by chemical analysis of residues and 2) experiments where the vapor species were identified by means of a mass spectrometer. Experimental Section. Sarnple Preparation. Samples of TiSe2 were prepared in a sealed, evacuated quartz ampule by heating to 1000°C stoichiometric amounts of selenium of 99.999+ pct purity obtained from the American Smelting and Refining Co. and titanium of 99.2 pct purity obtained from A. D. Mackay, Inc. After heating, the sample was ground and reheated to insure homogeneity. Samples containing less selenium than TiSez were prepared by mixing amounts of titanium powder and TiSez appropriate for the desired composition; the titanium and TiSez mixture was heated in the same manner as described for TiSe2. Analyses of titanium selenide samples contained in quartz crucibles were performed by gravimetric oxidation in oxygen at 800°C; the products of the oxidation were solid TiOz and gaseous Se02. The mass of the original sample and the mass of TiOn determined the Se/Ti atomic ratio. The sample of TiSen used in these experiments had a composition of 2.04 Se/Ti atomic ratio units. The compositions for all samples reported were analyzed by this method. Va/!orization Experiments. Samples of titanium selenides were vaporized in tungsten Knudsen crucibles. Some vaporization experiments were carried out in glass vacuum lines followed by chemical analyses of residues, and some vaporization experiments were performed with a Bendjx mass spectrometer as described previously.8

Jan 1, 1967

By Frederic Dewey

BONE-ASH cupels have been used from time immemorial to absorb litharge, and accompanying oxides; in assaying. Doubtless, also, from the earliest days cupels have been most unjustly blamed for much poor assaying. It has long been known that the precious metals go with the litharge into the cupel. This occasions a loss of precious metals and reduces the results of the assay. There have been many investigations of cupels and the most diverse views have been expressed, the extremes being the statements of Lodge 1 that every cupel has some effect upon the loss in assaying telluride ores and of the Campredons2 that coarse and fine and hard and soft cupels all give the same loss of silver when cupelling the same weights. The truth lies between these statements and much nearer the latter. In a vast majority of cases the influence of the cupel is not dominant and is outweighed by other conditions, particularly the temperature of the cupelling bead. At the Spokane meeting of the Institute I presented a paper on the Assay and Valuation of Gold Bullion,3 which recorded the results of many hundreds of assays made in the Mint service under everyday commercial conditions, which of necessity differ from scientific conditions. In following this matter up, for the purpose of increasing the accuracy of our commercial methods of bullion assays, the question of the absorption of gold by the cupel was found to be a most important one and was taken up for investigation. In a lesser degree, the silver absorption is important and interesting, but at present it appears to be far more complicated and, while many figures showing silver absorption may be found through this paper, much further investigation is required to put the subject upon a satisfactory basis.

Jan 11, 1917

By W. D. Forgeng, B. F. Decker

IT has been known for almost a century' that silicon and nitrogen combine when heated to a high temperature. Three nitrides have been reported, SiN, Si3N,, and Si,N, containing 33.3, 40.0 and 42.9 pct nitrogen by weight, respectively. The existence of SisN, is well established but that of Si,N, and SiN is doubtful. The first systematic study of the reaction between silicon and nitrogen was made in 1910 by Weiss and Engelhart" who determined the rate at which silicon absorbed nitrogen at temperatures from 1250°C to

Jan 1, 1959

By Frank A. Hill

After a long struggle with an underground mine-fire and its accompanying evils, having experienced the discouragement of many retreats, the uncertain hope of varying advances, and the gratification of final success, I am tempted to give the members of the Institute some of the details of the fight. I do not write with the thought of treating a novel subject, but with the hope that some one as unfortunate as ourselves may be led by our experience to avoid our mistakes and to profit by our successes. The fire occurred on June 16, 1890. It was a calamity awful in its results, ringing the death-knell of thirty-one stalwart miners, bringing sorrow and desolation to many homes, and destroying in a few hours the work of years. While there have been a number of disasters in the history of American mining in which there was a greater loss of life and property, I know of none in which so simple a cause led to results so serious. A description of the mine, with the details of the accident, is necessary for a full understanding of the conditions existing at the time. The Hill-Farm-Parrish mine is in Dunbar township, Fayette county, Pa., about one mile from Dunbar station, on the Pennsylvania and Baltimore & Ohio railroads, about four miles south of Connellsville, nine miles northeast of Uniontown, and in the heart of what is celebrated as the Connellsville coke region. The mine is owned and operated by the Dunbar Furnace Company ; and all the coal produced is made into coke and used in the company's furnaces, one mile to the east. The mine is opened by two slopes, the HillFarm and Parrish, the latter known also as the Ferguson. The Hill-Farm slope is 2600 feet northeast of the Parrish. There are 150 ovens at the former and 70 at the latter slope. The Hill-Farm slope is 4100 feet in length, and the length of the Parrish at the time of the accident was 3700 feet. The average dip of the coal is about 8 degrees S of W. The workings of the two slopes are con-

Jan 1, 1893

By F. N. Rhines

Sintering may be defined as the process by which powders bond themselves into coherent bodies, usually, although not necessarily, under the influence of pressure and elevated temperature. For the sake of clarity and simplicity, the present survey will exclude from consideration the sintering of mixed or alloyed powders, with attendant complications, but at the risk of overlooking information of general applicability. Sintering in the presence of a liquid phase is thus automatically eliminated. The sintering of alloys involves much additional subject matter and deserves separate consideration. Since the literature of the subject is extensive and widely scattered, it will not be feasible to consider the contributions individually. Instead, the subject matter will be classified according to experimental observations and theory, and will be presented in summary form. It should be noted that the appended list of references does not constitute a complete bibliography; it includes only those works quoted below. More extensive bibliographies are included in several of the references; see particularly references 7, 9, 28, 34, 38, 50, 52, 54, a "Bibliography on Powder Metallurgy" published by the Library of Congress and a pamphlet published by the Metals Disintegrating Co. entitled "The Field of Powder Metallurgy and Bibliography." 11. Summary of Experimental Observations The following classified list is composed of general statements of established fact derived from the experimental results reported in the published literature. A few contested observations are included, because of their potential importance; these are labeled as such. Any satisfactory and complete theory must be capable of explaining all of the uncontested facts. Obviously, some important facts may be missing from this list and these may hold the key to the correct explanation of the sintering process, but the possible lack of such material should not deter attempts to understand the subject on the basis of what is available here. A, The Initial Bond at Room Temperature a. To a limited extent uncompressed powders and massive metals adhere at room temperature. Clean tin powder forms a weak "cake" on standing at room temperature, the strength increasing with time. Clean gold surfaces adhere on light con-tact, as do those of many other substances, including nickel.27 b. Upon compression the strength of the bond- is increased progres-ivelv. There is a limit of pressure

Jan 1, 1946

By F. N. Rhines

Sintering may be defined as the process by which powders bond themselves into coherent bodies, usually, although not necessarily, under the influence of pressure and elevated temperature. For the sake of clarity and simplicity, the present survey will exclude from consideration the sintering of mixed or alloyed powders, with attendant complications, but at the risk of overlooking information of general applicability. Sintering in the presence of a liquid phase is thus automatically eliminated. The sintering of alloys involves much additional subject matter and deserves separate consideration. Since the literature of the subject is extensive and widely scattered, it will not be feasible to consider the contributions individually. Instead, the subject matter will be classified according to experimental observations and theory, and will be presented in summary form. It should be noted that the appended list of references does not constitute a complete bibliography; it includes only those works quoted below. More extensive bibliographies are included in several of the references; see particularly references 7, 9, 28, 34, 38, 50, 52, 54, a "Bibliography on Powder Metallurgy" published by the Library of Congress and a pamphlet published by the Metals Disintegrating Co. entitled "The Field of Powder Metallurgy and Bibliography." 11. Summary of Experimental Observations The following classified list is composed of general statements of established fact derived from the experimental results reported in the published literature. A few contested observations are included, because of their potential importance; these are labeled as such. Any satisfactory and complete theory must be capable of explaining all of the uncontested facts. Obviously, some important facts may be missing from this list and these may hold the key to the correct explanation of the sintering process, but the possible lack of such material should not deter attempts to understand the subject on the basis of what is available here. A, The Initial Bond at Room Temperature a. To a limited extent uncompressed powders and massive metals adhere at room temperature. Clean tin powder forms a weak "cake" on standing at room temperature, the strength increasing with time. Clean gold surfaces adhere on light con-tact, as do those of many other substances, including nickel.27 b. Upon compression the strength of the bond- is increased progres-ivelv. There is a limit of pressure

Jan 1, 1946

By T. D. Murphy

This chapter deals with those types of silica raw materials that have been segregated and refined by natural processes into nearly monomineralic deposits and hence, by virtue of their high degree of purity, have become the sources of commodities having special and somewhat restricted commercial uses. In some instances, these raw materials occur in nature as unconsolidated quartzose sand or gravel and can be exploited and used with very little preparation and expense. More often, they occur as sandstone, conglomerate, quartzite, quartz mica schist, or massive igneous quartz which must be crushed, washed, screened, and sometimes chemically treated before commodities of suitable compositional and textural characteristics can be successfully prepared. The occurrence and distribution of silica raw materials is summarized and an effort has been made to bring commodity definitions, critical properties, and specifications up to date. Presentation of mining and processing methods is considered beyond the scope of this article; they are, for the most part, conventional and well known. New production techniques are currently reported in the trade journals and are later adequately described in technical publications as promptly as competitive restrictions allow. Discussion on Basis of Use ABRASIVE USES Industrial silica used for abrasive purposes falls into three main categories: (a) blasting sand; (b) glass-grinding sand; and (c) stone-sawing and rubbing sand. Blasting sand is a sound closely-sized quartz sand which, when propelled at high velocity by air, water, or controlled centrifugal force, is effective for such uses as cleaning metal castings, removing paint and rust, or renovating stone veneer. It is commonly referred to as Sand Blast sand. Multicycle quartz sand is an efficient blasting agent by merit of its survival characteristics which are soundness, toughness, and hardness. Steel grit and shot have supplanted it to a large extent but owing to their higher cost and tendency toward deterioration in storage, are still not universally used. It is conceded that angularity promotes faster cutting but this is offset by a higher loss in fines. The peening action of a rounded grain is a desirable feature in achieving a satin finish for certain light metal castings but a subangular grain is unsurpassed for fast heavy cutting. Specifications are chiefly based on size frequency distribution but it is mandatory that the grain be free of adhering clay or irony coatings. Material that dusts upon handling will not be tolerated. There is no uniform trade designation for the many blasting sand grades. Most producers sell on the basis of numbered grades; that is, No. 1, No. 2 and so on, this generally connoting fine to coarser grades. Designation of grade by the two sieve sizes between which most of the material lies, is practiced in some areas. Thus, in a No. 1220 grade, 98 pct of the material passes a 12 mesh sieve and is retained on a 20 mesh sieve. Blasting sand specifications vary according to use. Coarse grades range from 4 mesh to 12 mesh, medium grades range from 12 mesh to 30 mesh, finer grades may range from 20 mesh to 100 mesh or finer. Specifications generally call for narrow limits of gradation, requiring precise sizing methods. The fact that most blasting sands are retained

Jan 1, 1960

By M. C. Leverett

Knowledge of the theory underlying the behavior of mixtures of fluids in reservoir rocks is essential to the proper solution of certain types of problems in petroleum production, but is as yet incompletely developed. The object of this paper is to show the application of well established thermody-namic and physical principles to these problems, and thus to assist in the development of the basic theory. For convenience the problems to be considered here may be divided into two groups: 1. Static problems, involving only the static balance between capillary forces and those due to the difference in densities of the fluids; i.e., gravitational forces. 2. Dynamic problems, involving analysis of the motion oi mixtures of immiscible fluids in porous media under the influence of forces due to gravity, capillarity, and an impressed external pressure differential. Capillary Equilbrium in Sands Under this heading the static type of problem will be discussed and the results of experimental investigations on the capillary properties of unconsolidated sands will be presented. Although the discussion of this section is, in a sense, prefatory to the treatment of problems of mixture flow, the concepts developed here have considerable intrinsic importance apart from their ap-plication to flow problems. For, it is reason-able to postulate that the reservoir fluids are, owing to their long existence in undis- turbed mutual contact prior to exploitation, in substantial equilibrium. It follows that their distribution in the reservoir at the time of tapping should be entirely predictable from the theory of capillary equi librium, provided certain experimentally measurable properties of the reservoir rock are known. Knowledge of the distribution of the several fluids in the reservoir is, ol course, helpful in the estimation of reserves and in other problems. It is to be emphasized that throughout the discussion of capillary statics it is assumed that the fluids are in equilibrium from the capillary standpoint. Thus, water, where it is referred to as being in a reservoir, will be understood to be interstitial water, present at the time of drilling the reservoir, commonly termed "connate" water. The theory developed here is perfectly general for any porous solid, whether a carefully prepared unconsolidated sand or a natural sandstone from an oil reservoir. At present, however, only problems involving clean, unconsolidated sands can be made to yield numerical solutions, since only such sands have been adequately investigated experimentally. Experimental evaluation of the pertinent properties 01 natural reservoir rocks will permit the extension of the numerical treatment to problems involving these materials. We shall now consider in some detail the static equilibrium of fluid mixtures in porous solids: that is, the manner in which the reservoir fluids are distributed vertically whell the Forces due to capillarity are just balanccd by those due to gravitation.

Jan 1, 1941

By M. C. Leverett

Knowledge of the theory underlying the behavior of mixtures of fluids in reservoir rocks is essential to the proper solution of certain types of problems in petroleum production, but is as yet incompletely developed. The object of this paper is to show the application of well established thermody-namic and physical principles to these problems, and thus to assist in the development of the basic theory. For convenience the problems to be considered here may be divided into two groups: 1. Static problems, involving only the static balance between capillary forces and those due to the difference in densities of the fluids; i.e., gravitational forces. 2. Dynamic problems, involving analysis of the motion oi mixtures of immiscible fluids in porous media under the influence of forces due to gravity, capillarity, and an impressed external pressure differential. Capillary Equilbrium in Sands Under this heading the static type of problem will be discussed and the results of experimental investigations on the capillary properties of unconsolidated sands will be presented. Although the discussion of this section is, in a sense, prefatory to the treatment of problems of mixture flow, the concepts developed here have considerable intrinsic importance apart from their ap-plication to flow problems. For, it is reason-able to postulate that the reservoir fluids are, owing to their long existence in undis- turbed mutual contact prior to exploitation, in substantial equilibrium. It follows that their distribution in the reservoir at the time of tapping should be entirely predictable from the theory of capillary equi librium, provided certain experimentally measurable properties of the reservoir rock are known. Knowledge of the distribution of the several fluids in the reservoir is, ol course, helpful in the estimation of reserves and in other problems. It is to be emphasized that throughout the discussion of capillary statics it is assumed that the fluids are in equilibrium from the capillary standpoint. Thus, water, where it is referred to as being in a reservoir, will be understood to be interstitial water, present at the time of drilling the reservoir, commonly termed "connate" water. The theory developed here is perfectly general for any porous solid, whether a carefully prepared unconsolidated sand or a natural sandstone from an oil reservoir. At present, however, only problems involving clean, unconsolidated sands can be made to yield numerical solutions, since only such sands have been adequately investigated experimentally. Experimental evaluation of the pertinent properties 01 natural reservoir rocks will permit the extension of the numerical treatment to problems involving these materials. We shall now consider in some detail the static equilibrium of fluid mixtures in porous solids: that is, the manner in which the reservoir fluids are distributed vertically whell the Forces due to capillarity are just balanccd by those due to gravitation.

Jan 1, 1941

By B. L. Averbach

Recovery and primary recrystalliza-tion in cold worked metals are usually considered as two competing processes. Some of the effects which usually accompany recovery are: alleviation of stress corrosion tendencies, changes in thermal emf,1 damping capacity,2 electrical resistivity,2 and magnetic properties,3 and only minor changes in hardness or the related strength properties. During primary recrystalliza-tion new unstrained grains are formed at the expense of the strained matrix. These new grains eventually become visible metallographically, and nucle-ation and growth kinetics have been indicated for this process.4,5 Frequent attempts have been made to study the cold-working phenomenon by observations on the line broadening by X ray diffraction patterns. Relatively few measurements of line intensities have been made, although Brind-ley and his collaborators, 6,7,8 by means of film techniques, compared the intensities of cold worked Cu, Ni, and Rh patterns with those from chemically precipitated powders. These precipitated powders were presumed to be strain free, and it was found that the intensities for the cold-worked materials progressively decreased as the Bragg angle increased except for the first line, where there was an increase due to reduction in extinction. This was interpreted as a randomness in atomic position induced by cold work. Such randomness is similar to that caused by thermal agitation and has been described as "frozen heat" displacement of 0.08-0.10 A from the mean atomic position. In a recent study9 on the effect of cold work in metals on their powder pattern intensities, the changes in integrated intensity for heavily cold worked alpha brass were observed as a function of the annealing temperature. These measurements were made with a manually operated Geiger-counter spectrometer using CuKa radiation monochromated with a rock salt crystal. Intensity measurements were made with a scaling meter over small intervals of angle, and the equipment was so arranged that the diffracted and incident beams made equal angles with the specimen. Intensities could be compared directly by simply interchanging specimens, and comparisons from day to day were made with a standard whose line intensities did not change on aging. It was shown that a cold worked alpha brass standard was stable for at least a year. Table 1 indicates the results of the integrated intensity measurements on a 70 Cu-30 Zn brass. In the sample preparation, a brass plate was first cold rolled 50 pct and then filed, screened to —325 mesh, compacted into briquettes at a pressure of 60,000 psi and finally annealed for one hour at various temperatures up to 400°C. The briquetting pressure did not seem to influence the integrated intensities, and most of the cold work was introduced by the filing. Although this method of cold work is not quantitative, it was used to obtain random orientation (and thus uniform diffraction lines) in order to make accurate measurements of integrated intensity. Back reflection patterns were taken in each case to check the uniformity of the lines, and from the observed line broadening it was apparent that this type of plastic deformation was quite severe. Care was taken to traverse the entire background of the pattern and to assign to each peak the total intensity above this background. The bases of the diffraction lines were quite broad and spread out over several degrees, even for the narrow peaks. The theoretical intensities were calculated to include a temperature correction, a dispersion correction, and a Lorenz- polarization factor corrected for the crystal monochromated beam. In Table 1 it was necessary to match the calculated and observed values at only one point, and the rest of the experimental values were converted directly to this arbitrary scale. The integrated intensities in Table 1 are listed in arbitrary units, and the accuracy was sufficient to reproduce any of the measured line intensities to within + 1.5 units. It is evident that the percentage error on the strongest line (111) was quite low. The calculated values and the observed intensities for the cold worked material matched reasonably well. As the annealing temperature was raised, however, the intensity of the strongest reflections, particularly the (lll), decreased measurably. Since the background intensities of all of these patterns were identical, such behavior could be interpreted as a primary

Jan 1, 1950