Search Documents

By B. A. Shaw

Historically, microwave tubes have been fabricated from massive metal and ceramic components. The current trend is to lighten tibes for airborne applications. The reqciiremenls of light weight and also reduced cost have created a novel approach to tube structure in which thin-film technology plays a major role. Although the electrical requirements of thin-film circuits in microwave tubes differ from those required or se,niconductor integrated circuits. the technology is basically similar. The stringent requirements of the micvowave tube have created sophisticaled thin-film techniques thut are of interest to the integrated-circuit industry in general. This paper describes a nunzber of thin-jilm techniques recently developed and discusses in detail the application of the technology in microwave tubes. The particular areas of interest are: 1) ceramic mounted thin-film slow-wave structures; 2) thin-film secondary emitters; 3) suppression of tube environnental multipactor by semiconducting' thin films; and 4) age-hardenable and dispersion-hardened thin metal films. SEVERAL thin-film techniques specifically applied to microwave power tubes are discussed in this report. There are two reasons for this work. One is the necessity of reducing weight and cost of microwave tubes and the other is related to overcoming problems in the tube operation by the use of applied thin-film technology. The major emphasis of this work has been on tube slow-wave structures. Other work in the area of secondary emission, either its suppression or its enhancement, is continuing; the most satisfactory results to date have been by utilization of thin-film technology. The requirements of high thermal and electrical conduction together with greater strength than normally obtained with elemental materials have led to the development of dispersion-hardened films. The paper will discuss: 1) ceramic-mounted delay-line microwave tubes; 2) multipactor and secondary emission; 3) hardened films. I) CERAMIC-MOUNTED THIN-FILM SLOW-WAVE STRUCTURES In a conventional crossed-field microwave tube, the slow-wave or delay-line structure is produced from two carefully machined components. One half of the structure is shown in Fig. 1. The other half is the mirror image of the first but is rotationally offset by a half a period. The combined structure now forms an interdigital type of slow-wave structure and is the anode of the tube as shown in Fig. 2. The period and finger length of an interdigital slow-wave structure are prescribed by the desired dispersion characteristics. The typical design is as shown in the first figure; it can be noticed that the finger width is several times greater than the finger thickness. Even assuming that it were mechanically possible to produce free-standing fingers of extremely small cross-sectional dimension, for example, 0.002 in. thick by 0.005 in. wide by 0.500 in. long, decreasing this finger width would increase the tube efficiency but would also decrease the thermal-conduction path, causing an increased temperature rise from intercepted rf current which in its extreme could easily cause finger melting. Hence, for free-standing lines of this type, the design is a compromise between mechanical capabilities, tube efficiency, and thermal dissipation. These structures are also expensive and tend to be heavier than purely electrical considerations would demand. In the present approach, we have transposed the three-dimensional structure previously shown into an essentially two-dimensional structure as shown in Fig. 3. The linear structure is used here for clarity of detail. The support member is a ceramic material and the line is deposited copper. The final tube design is shown in Fig. 4. Because of the backwall sup-

Jan 1, 1967

By O. W. Ellis

IN VIEW of the extensive use of the brasses and bronzes in engineering practice it is indeed surprising that so little scientific work has been done on the oxides in these alloys. Recognition of the ill effects of these compounds is universally accorded, both in foundry procedure and in such specifications as cover the melting of these useful mixtures. In the latter, limits, for example, are placed on the proportions of scrap metal in the charge, and clauses governing the use of fluxes are included, the addition of fluxes to the charge being made with the object of avoiding oxidation during the process of melting and of subducing and separating non-metallic matter from the melt.1 In the manufacture of brass it occasionally, though rarely, occurs that the virgin metals, copper and zinc, alone are used. In the event of virgin metals being employed, that of the higher melting point is always melted first. If it is melted under suitable conditions, little or no oxidation will occur. Whether oxidation has occurred or not, however, can best be determined by microscopic examination of a sample taken from the melt.

Jan 1, 1930

By K. A. Jackson, G. A. Chadwick, A. Klugert

The diffusion field ahead of a lamellar interfnce is analyzed using an electrical analog. A self-consistent solution is obtained for the shape of the interfnce and the diffusion field by an iterative process. The solutions presented here are for a 50-50 eutectoid or eutectic, The shape of the interface is found to he independent of growth velocity and lamellar spacing, and to depend on the relative values of interfacial free energies at the phase houndaries . The mode of growth of lamellar eutectics and eutectoids has been a subject of much interest for many years.1-4 Mehl and Hagel 1 have shown photomicrographs taken by Tardif when he attempted to determine experimentally the shape of an advancing pearlite interface; the results are completely ambiguous. Brandt' and schei13 have made approximate calculations of the composition ahead of a lamellar growth front. The shape of the advancing front and the composition distribution ahead of the front are difficult to calculate because one depends on the other. It is the purpose of the present paper to describe a method by which this calculation has been done. Lamellar-eutectic growth usually occurs under conditions where the growth is fairly rapid, and the interface temperature is close to the eutectic temperature. The growth rate is usually determined by heat flow. Eutectoid growth, on the other hand, can best be studied by quenching to some temperature, and allowing growth to proceed isother-mally. In both cases the growth is believed to be controlled by diffusion* rather than by the atomic kinetics of the transformation. This being the case, a single treatment of the diffusion equation will apply to both cases, provided the region of the interface in a eutectic may be considered to be isothermal. If a part of the interface could appreciably change its thermodynamic driving force by advancing ahead of or lagging behind the mean interface, then the two cases would not be similar. Eutectics normally grow in temperature gradients of the or-der of a few degrees per centimeter. The normal eutectic spacing is the order of a few microns. Part of the interface would have to extend many lamellar spacings ahead of the mean interface before it experienced sensibly different conditions. The interface temperature is usually a few tenths of a degree below the eutectic temperature so that temperature differences of the order of one-thousandths of a degree (a displacement of one lamellar spacing) would be unimportant. Protrusions large compared to the mean spacing do occur when one phase only grows into a eutectic liquid. This is usually a dendritic type of growth, and easily distinguishable from the lamellar mode of growth. A single treatment of lamellar growth will apply equally well to both eutectic and eutectoid decomposition. At the interface, which as shown above is essentially isothermal, the difference between the equilibrium eutectic temperature Teu and the actual interface temperature Ti, can be divided into two parts: 1) the composition varies across the interface, so that the local equilibrium temperature is not Teu; and 2) the interface is curved, so that the local equilibrium temperature is depressed according to the Gibbs-Thompson relationship. This undercooling can be written as Teu-Ti =?T = mAC(x) + a/r(x) [1] where ?C(X) is the departure of the composition at a point x on the interface from the eutectic composition, see Fig. 1, r(x) is the local radius of curvature at a point x on the interface, m is the slope of the liquidus line on the phase diagram, and a is a constant given by where s is the interfacial free energy, TE is the equilibrium temperature, and L is the latent heat of fusion. The calculations in this paper will be made only for the case where the phase diagram is symmetric, that is, the eutectic occurs at 50 pct, the liquidi have the same magnitude slope m at the eutectic temperature, and C,, the amount of B rejected when unit volume of a freezes, see Fig. 2(a), is the same for both phases. As shown in Fig. 2(b), the composition ahead of the a phase will be rich in B, the composition ahead of the ß phase will be rich in A. The composition at the phase boundary is the eutectic composition. The difference between the local liquidus temperature and the actual tempera-

Jan 1, 1964

By G. D. Bengough

CORROSION tests should be designed so as to facilitate as far as possible the interpretation of results, consequently factors which may affect the rate of corrosion should be controlled as far as practicable, and very full data should be given regarding the conditions of the test. Among the most important factors affecting the rate of corrosion is often the rate of supply f oxygen to the metal surface. It is essential therefore to understand the mechanism by which oxygen is transferred from the liquid surface to the surface of the metal. The work of Adeney and his coworkers has thrown much light on this mechanism. They have shown1 that the aeration of deaerated water and salt solutions proceeds much more rapidly than can be accounted for by mere diffusion, and have suggested that downward "streaming" takes place from the surface of the water, due mainly to an increase of density brought about by evaporation. The evaporation reduces the temperature of the surface layer, and also increases the concentration in the case f salt solutions. The effect of evaporation in facilitating the transfer of oxygen to a metal and increasing the corrosion f the metal was shown in some experiments due to Friend .2 He tested the corrosion f mild steel plates immersed in water in glass jars, a steady stream f air being drawn over the surface of the water in the jars. The air passing through half the number f jars was saturated with moisture, that passing through the others was dried with calcium chloride. He found that "in every case the water exposed to dry air was approximately twice as corrosive as that exposed to air saturated with water vapor."

Jan 1, 1929

By Roy Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe-rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always-have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1951

By Charles Morgan

An increased demand for brown iron ore in the Birmingham district during the past 18 months has caused renewed activity both in prospecting and mining these ores. In recent years the production in Alabama has ranged from 41,559 tons in 1932 to 639,351 tons in 1928. During the last 9 years about 83 per cent of the total brown ore produced in the United States has come from Alabama (Tables 1 and 2). Prospecting Two methods of prospecting are used in this district: (1) test pits, (2) churn-drilling. Usually there is certain quite definite information on an area to be prospected; some of the indications are float ore such as small gravel or small and large boulders known as "dornicks" scattered over the surface, and ore exposed by erosion in gulleys and ravines, which have cut or eroded through the overburden. Often these natural erosions furnish an indication of the thickness of the ore and to some extent of the area of the ore body. Deposits of brown ore are very irregular both in thickness and extent. Deposits are often lens-shaped or long narrow leads, some of which may be parallel and separated from one another by sand, clay or gravel. The bottom—the footwall—is also very irregular. This footwall is usually lime clay—disintegrated limestone, locally called "white horse," which usually is found at a depth of 6 in. to 20 ft. overlying the limestone. At some places sand and gravel is found under the ore instead of clay. No ore is found under the lime clay, although often the ore has sunk or slumped and is found in the upper portion of this clay, as at some of the Sloss workings at Russellville. The origin of these ores has been discussed by Major E. C. Eckel and Dr. E. F. Burchard in U. S. Geological Survey Bulletin 400, and recently the latter has done further work on ores in the Russellville district, of which reports undoubtedly will be published.

Jan 1, 1940

By Charles Morgan

An increased demand for brown iron ore in the Birmingham district during the past 18 months has caused renewed activity both in prospecting and mining these ores. In recent years the production in Alabama has ranged from 41,559 tons in 1932 to 639,351 tons in 1928. During the last 9 years about 83 per cent of the total brown ore produced in the United States has come from Alabama (Tables 1 and 2). Prospecting Two methods of prospecting are used in this district: (1) test pits, (2) churn-drilling. Usually there is certain quite definite information on an area to be prospected; some of the indications are float ore such as small gravel or small and large boulders known as "dornicks" scattered over the surface, and ore exposed by erosion in gulleys and ravines, which have cut or eroded through the overburden. Often these natural erosions furnish an indication of the thickness of the ore and to some extent of the area of the ore body. Deposits of brown ore are very irregular both in thickness and extent. Deposits are often lens-shaped or long narrow leads, some of which may be parallel and separated from one another by sand, clay or gravel. The bottom—the footwall—is also very irregular. This footwall is usually lime clay—disintegrated limestone, locally called "white horse," which usually is found at a depth of 6 in. to 20 ft. overlying the limestone. At some places sand and gravel is found under the ore instead of clay. No ore is found under the lime clay, although often the ore has sunk or slumped and is found in the upper portion of this clay, as at some of the Sloss workings at Russellville. The origin of these ores has been discussed by Major E. C. Eckel and Dr. E. F. Burchard in U. S. Geological Survey Bulletin 400, and recently the latter has done further work on ores in the Russellville district, of which reports undoubtedly will be published.

Jan 1, 1940

By R. G. Hawthorne

This report is concerned with fluid displacement in porous media, in those cases where viscous and gravitational forces control the displacement. Such a system would usually be found in a sand body of large physical dimensions such as an oil reservoir, although it is possible to create such a system in the laboratory. It is shown that the position of the fluid interface can be predicted by numerical calculations using a basic idea presented by Dietz. Fluid flow is considered in a vertical plane in a homogeneous, porous medium of sufficient thickness that the capillary transition zone is small in comparison with the total reservoir. A theory developed by Dietz' is used to make numerical calculations of the position of the fluid interface. The results for several conditions are compared with scaled model experiments. The results show that, for gas drive in a reservoir of steep dip, a relatively low flow rate can displace large volumes of oil before gas breakthrough. On the other hand, water injection at favorable mobility ratio and low dip may show best performance at high rates. Water tends to underride the oil and, given sufficient rime, will break through without much oil displacement. For certain conditions, which include relatively low flow rate, the interface is a straight line and its behavior is simple to calculate. At higher flow rates, the interface is unstable, and a numerical solution was programed for an automatic computer. In general, good agreement is shown between the fluid model and the computed results so long as gravitational forces have control. For a water drive at very unfavorable mobility ratio, many small water fingers appear. These viscous fingers are not controlled by the relatively small gravitational forces. When viscous fingering becomes the controlling factor, the mathematical model is oversimplified, and results do not check the fluid flow model. INTRODUCTION Present methods of reservoir analysis depend upon certain simplifying assumptions to obtain mathematical descriptions of practical use. Material-balance methods (Muskat2 or Tarner2) assume uniform fluid saturations in the entire reservoir, or in a few subdivisions of the reservoir. An unsteady-state flow calculation by West, er at considered pressure and saturation changes in flow to a well during solution gas drive, and neglected gravity effects. Results showed only a 4 per cent difference for ultimate oil recovery by the Muskat method, even though the case chosen for study was one in which unsteady-state effects should be high. The Buckley-Leverett5 method commonly assumes a one-dimensional flow system. It is applicable at high flow rates where viscous forces predominate over gravity forces. Simultaneous, parallel flow of the two fluids is assumed, and the concept of a fluid interface is not introduced. Permeabilities to each fluid for a given saturation must be known. The method is not applicable for a two-dimensional system where cross flow becomes possible. Less well known is the displacement equation derived by Dietz. This method is designed for two-dimensional flow systems and assumes a definable fluid interface within the porous medium. Dietz showed that, for a range of low flow rates, the interface would be stable. straight and at an angle of inclination which could be simply calculated. At a certain critical flow rate, the calculated interface tilt would equal the formation dip. For higher flow rates, a finger of displacing fluid would invade the displaced fluid. Dietz indicated that his method applied only to macroscopic reservoir behavior, while the Buckley-Leverett method applied to the small transition zone at the fluid interface. The examples worked out in this report are based on the fluid-displacement theory of Dietz. It is shown that the Dietz theory may be used to derive equations analogous to the Buckley-Leverett equations. In contrast to the Buckley-Leverett method, flow is considered in a plane rather than being limited to a line. Rather than a frontal advance, the movement of a fluid interface is followed. For flow rates substantially exceeding the critical rate and for high viscosity ratio, many fingers of invading fluid occur-—rather than the single finger assumed by Dietz. On the other hand, so long as some gravitational influence remains, the flow is not entirely parallel to the bedding planes as assumed by Buckley and Leverett; therefore, both methods fail to give an adequate descrip-

By J. M. Flaitz, A. S. Parks

OF the various methods of sampling gas-condensate wells, a method that secures a continuous representative sample of the well stream is desirable. Such a method, consisting of a sampling tube introduced into the well tubing, has proved satisfactory. The method is sufficiently accurate for operating and engineering problems. A portable testing apparatus can be used with the sampling tube to obtain data useful in studying the economic and technical aspects of the development and operation of gas-condensate properties. INTRODUCTION The recent discovery and development of gas reserves that contain hydrocarbons that condense with reduction of temperature or pressure, or both, to form a product known as condensate, has brought many new problems to the oil and gas industries. With further discovery of deep, high-pressure fields it is presumable that many more gas fields of this type will be added to the steadily increasing number. Such gas reserves are found either associated with oil as a gas cap or in separate formations. There seems to be no positive correlation between the physical or geological nature of the reservoir, and the chemical composition or phase characteristics of its contents. Knowledge of the chemical make-up and phase behavior of gas-condensate reserves are needed to cope with many problems. A knowledge of the chemical composition and phase characteristics of the reservoir material is necessary to properly design a gasoline or recycling plant, to estimate natural gas and condensate reserves, to enable the operator to study the economic and technical aspects of various methods of operation and development, and to carry out the plan of operating subsurface and surface lease equipment. This information is often useful in questions of mineral ownership, proration, legal position, and taxation. It is the purpose of this paper to discuss methods used by the writers to determine the chemical composition and phase characteristics of the fluids produced from a condensate well. The scope of the paper includes a discussion and description of the method of sampling, the results of tests on the accuracy of the sampling method, a description of a portable testing apparatus used to examine the phase characteristics, typical results of tests on wells from several condensate fields, and some of the applications of these data to production problems. References to previous work on this subject are cited at the end of the paper. THE PROBLEM At reservoir conditions of temperature and pressure, the fluids produced from a condensate well exist in a homogeneous vaporous condition. The consequent reduction of temperature and pressure that occurs as this gas enters and flows up the well tube results in condensation of some of the hydrocarbon material to form a liquid. The relative amount of liquid condensed at any point in the flowing system

Jan 1, 1941

By Walter Craft, John L. Lamont

Adequate hardenability has long been recognized as one of the first requirements for producing desired mechanical properties in a heat-treated steel. Since the introduction of the Jominy end-quench test' and the development of correlative information to expand its use, industry has had an effective measure of hardenability. Prediction and control of the hardenability have been made possible by Grossmann's principle2 for calculating hardenability from chemical composition; and Field's conversiona from depth of half-martensite hardening to Rockwell C hardness has made the relation more quantitative. These developments have facilitated the design of new steels and the control of standard grades to the extent that it has been possible to establish tentative hardenability bands for some of the more commonly used alloy steels.4 As the depth of hardening of the Jominy test specimen is usually measured by Rockwell C hardness, it was considered that it should be possible to predict the hardness by a more direct calculation. It has been found that this can be accomplished by the addition of Rockwell C units proportional to the carbon and alloy content, grain size, and position in the Jominy test specimen. The calculation has been found to be fairly accurate, and because of its additive character is relatively simple to use. In principle the method of calculation is somewhat similar to the expressions developed by Herty, McBride, and Hollen-back,5 Burns, Moore, and Archer,= and Burns and Riege1.l The calculation is started from a base that includes the effects of carbon content and position in the Jominy test speimen. Rockwell C units are added to the base in proportion to the alloy content and grain size. This sum represents the Rockwell C hardness up to the level at which a disproportionate increase of hardness is caused by the formation of martensite, and above this level an increment for martensite hardening is added. The effects of alloys are directly proportional to the amounts present and are independent of each other, the carbon content, and the position in the specimen. Furthermore, the factors for determining the martensite increment are dependcnt only on carbon content and are independent of cooling rate and alloy content. It is this absence of interrelation between the different factors that makes it possible to calculate the hardness and makes the method of calculation consistent with the principle that the character of the hardening reaction is governed primarily by carbon and that alloys exert their effect chiefly through control of the critical cooling rate. The principle of the calculation, and the effects of alloys on the critical cooling rate,

Jan 1, 1947

By John L. Lamont, Walter Craft

Adequate hardenability has long been recognized as one of the first requirements for producing desired mechanical properties in a heat-treated steel. Since the introduction of the Jominy end-quench test' and the development of correlative information to expand its use, industry has had an effective measure of hardenability. Prediction and control of the hardenability have been made possible by Grossmann's principle2 for calculating hardenability from chemical composition; and Field's conversiona from depth of half-martensite hardening to Rockwell C hardness has made the relation more quantitative. These developments have facilitated the design of new steels and the control of standard grades to the extent that it has been possible to establish tentative hardenability bands for some of the more commonly used alloy steels.4 As the depth of hardening of the Jominy test specimen is usually measured by Rockwell C hardness, it was considered that it should be possible to predict the hardness by a more direct calculation. It has been found that this can be accomplished by the addition of Rockwell C units proportional to the carbon and alloy content, grain size, and position in the Jominy test specimen. The calculation has been found to be fairly accurate, and because of its additive character is relatively simple to use. In principle the method of calculation is somewhat similar to the expressions developed by Herty, McBride, and Hollen-back,5 Burns, Moore, and Archer,= and Burns and Riege1.l The calculation is started from a base that includes the effects of carbon content and position in the Jominy test speimen. Rockwell C units are added to the base in proportion to the alloy content and grain size. This sum represents the Rockwell C hardness up to the level at which a disproportionate increase of hardness is caused by the formation of martensite, and above this level an increment for martensite hardening is added. The effects of alloys are directly proportional to the amounts present and are independent of each other, the carbon content, and the position in the specimen. Furthermore, the factors for determining the martensite increment are dependcnt only on carbon content and are independent of cooling rate and alloy content. It is this absence of interrelation between the different factors that makes it possible to calculate the hardness and makes the method of calculation consistent with the principle that the character of the hardening reaction is governed primarily by carbon and that alloys exert their effect chiefly through control of the critical cooling rate. The principle of the calculation, and the effects of alloys on the critical cooling rate,

Jan 1, 1947

By A. W. Cochardt

THERE are a number of effects that can cause material damping or internal friction. Some of these are frequency dependent, such as the thermo-elastic effect' and the stress-induced ordering.' Others depend on the amplitude of vibration, i.e., the damping related to the motion of dislocations3 and that due to magneto-mechanical hysteresis.' While many of these effects have been studied, only the magneto-mechanical effect has found extensive practical application. It is the principal source of damping in the current blade material in steam turbines.A magneto-mechanical hysteresis loop is seen in Fig. 1. If an unmagnetized, polycrystalline wire of a material exhibiting magneto-mechanical hysteresis, such as an Fe-14 pct A1 alloy, is twisted in torsion, a relation between shear stress and shear strain y is observed as indicated. The stress-strain curve does not follow Hooke's law -dashed line. Instead, the strain y increases nonlinearly and partly irreversibly, due to the motion of ferromagnetic domain walls,* until a critical stress is reached, which in this case is about 3,500 psi. If the applied stress is raised further, the strain appears to increase linearly and reversibly in accordance with Hooke's law, since all domains are now aligned in easy directions of magnetization nearest to the direction of the applied stress, and plastic flow has not yet started noticeably. On removing the applied stress, a remanent shear strain y, is observed, which is related to the irreversible magnetostriction of the material.' The energy dissipated in the material during a stress-strain cycle is proportional to the critical stress t, and the remanent magnetostrictive shear strain 7,. The purpose of this investigation was to make a survey of the magneto-mechanical damping of ferro-

Jan 1, 1957

By L. L. Gray, D. W. Reed, F. Morgan

A flowMeter has been developed at Gulf Research and Development Co. and tested in the field for measuring the flow of gas in well bores. It has been used in a study of the injection capacity of different horizons in gas injection wells in Oklahoma. The flow sensitive element of the meter is a semi-conductor having a very high temperature coefficient of resistance. Advantages possessed by this meter are the result of that property and the high specific resistance of the element. The instrument possesses a sensitivity considerably higher than any reported previously. In the application described here the element is heated to a temperature considerably above ambient by an electric current, which is supplied by a voltage source at the surface. When fluid flows through the meter the rate of dissipation of heat is increased and the temperature of the element decreases. Because of the negative temperature characteristics of the resistance element such a decrease of temperature will be accompanied by an increase of resistance which, under flow conditions ordinarily found in wells, is of such a magnitude that it can be directly measured or recorded in terms of a change in voltage at the surface. In practice, rate of flow is measured in terms of the drop in voltage in the resistance element. All the metering and control apparatus remains at the surface while the thermal element is lowered into the well on a single conductor cable, consisting of an insulated wire and sheath. The meter is calibrated by passing known quantities of gas through it either at the surface or in the hole at a point immediately above the region in which gas is lost to the formation. In case calibration is made at the surface, the ambient temperature in the hole may readily be obtained by a second resistance element which is operated at a current so low that effectively no heating occurs. The instrument has been adapted to con-tinuous recording, but the velocity of the meter relative to that of the gas must be low unless corrections are made. Curves giving data obtained in actual field tests are shown' The meter can also be used to determine the distribution of flow capacity in a gas producing well. A differential form of the meter has been designed and built in which the local flow or injection capacity of the formation is obtained directly. Introduction When fluid is injected into a well in a secondary recovery or pressure-maintenance operation the question of its most effective use invariably arises. Although the core log, when available, will show the regions of good permeability and oil saturation, there is normally no assurance that the fluid actually enters the formation in zones where injection is deemed desirable. In view of the uncertainties involved in such programs, it is generally conceded that measurements of permeability for a formation in place are more significant than those obtained by the core-sampling technique. A subsurface meter has been developed at the Gulf Research and Development Co. for measuring flow of fluids at different horizons in a well bore, and field tests have been made on the instrument in Cooperation with the Tulsa Division of the Gulf Oil Corp. In this paper the meter is de-

Jan 1, 1948

By F. Morgan, L. L. Gray, D. W. Reed

A flowMeter has been developed at Gulf Research and Development Co. and tested in the field for measuring the flow of gas in well bores. It has been used in a study of the injection capacity of different horizons in gas injection wells in Oklahoma. The flow sensitive element of the meter is a semi-conductor having a very high temperature coefficient of resistance. Advantages possessed by this meter are the result of that property and the high specific resistance of the element. The instrument possesses a sensitivity considerably higher than any reported previously. In the application described here the element is heated to a temperature considerably above ambient by an electric current, which is supplied by a voltage source at the surface. When fluid flows through the meter the rate of dissipation of heat is increased and the temperature of the element decreases. Because of the negative temperature characteristics of the resistance element such a decrease of temperature will be accompanied by an increase of resistance which, under flow conditions ordinarily found in wells, is of such a magnitude that it can be directly measured or recorded in terms of a change in voltage at the surface. In practice, rate of flow is measured in terms of the drop in voltage in the resistance element. All the metering and control apparatus remains at the surface while the thermal element is lowered into the well on a single conductor cable, consisting of an insulated wire and sheath. The meter is calibrated by passing known quantities of gas through it either at the surface or in the hole at a point immediately above the region in which gas is lost to the formation. In case calibration is made at the surface, the ambient temperature in the hole may readily be obtained by a second resistance element which is operated at a current so low that effectively no heating occurs. The instrument has been adapted to con-tinuous recording, but the velocity of the meter relative to that of the gas must be low unless corrections are made. Curves giving data obtained in actual field tests are shown' The meter can also be used to determine the distribution of flow capacity in a gas producing well. A differential form of the meter has been designed and built in which the local flow or injection capacity of the formation is obtained directly. Introduction When fluid is injected into a well in a secondary recovery or pressure-maintenance operation the question of its most effective use invariably arises. Although the core log, when available, will show the regions of good permeability and oil saturation, there is normally no assurance that the fluid actually enters the formation in zones where injection is deemed desirable. In view of the uncertainties involved in such programs, it is generally conceded that measurements of permeability for a formation in place are more significant than those obtained by the core-sampling technique. A subsurface meter has been developed at the Gulf Research and Development Co. for measuring flow of fluids at different horizons in a well bore, and field tests have been made on the instrument in Cooperation with the Tulsa Division of the Gulf Oil Corp. In this paper the meter is de-

Jan 1, 1948

By E. A. Lucero, H. E. Robbins, T. H. Dudley

EL Salvador mine of Andes Copper Mining Co., E subsidiary of Anaconda Co., is in northern Chile about 18 miles north of Potrerillos, 7825 ft above sea level. Initial production is planned for the first half of 1959. Plant capacity will be 30,000 tpd, and there are 308,835,000 tons of proven ore reserves, averaging 1.49 pct Cu. The Inca adit is being driven as part of the mine-to-mill haulageway. Because of the overburden it is planned to mine the deposit by block caving. Ore will be dropped from upper gathering levels through ore passes to the Inca adit, through which it will be transported out of the mine to the primary crushing plant located a half mile from the portal.

Jan 3, 1958

By E. B. Olds, Burt. B. P.

THE mines of the Consolidated Coppermines Corporation are at Kimberly, in the Robinson mining district, White Pine County, Nevada. [ ] The blanket-like ore body is a disseminated copper deposit occurring in monzonite porphyry and, in general, is thoroughly fractured, altered, and soft. Contained in the porphyry ores of the extreme westerly end of the ore body are pendants of hard garnetized limestone. A younger monzonite porphyry underlies the ore-bearing porphyry, which in turn rests on limestone and shale. Block caving is the standard method of mining. Because of the undulating top and bottom contours of the ore body, the main haulage level was selected and driven at an elevation calculated to be the most economic depth below the major tonnage sections of ore. Fig. I shows a general section of the Emma Nevada ore body taken through its long axis, which lies roughly in an east-west direction. Mine openings in either type of porphyry require heavy timbering and constant maintenance and repair, particularly in horizons at or near the ore body contact. Where the ore lies close to the haulage level, slusher hoists and scrapers are used to transport horizontally the ore to the main haulage drift (Fig. 2). For the extraction of high-lying ores, a system of branch raises is used; and the ore is mined by gravity. Slushing methods are used also on the high-lying ore-body fringes. Slusher drifts are often driven from the fringe branch raises that have already served their purpose, in order to minimize the cost of the preparatory work in mining the thinner portions of the ore body (Figs. 3 and 4). When a block of ore is developed and undercut, it is economical to mine it as rapidly as the ore will cave efficiently; and this procedure often presents safety problems because of men with equipment working in a relatively congested area. The single-track main haulage drift is about 1 ½ miles long, and lateral haulage drifts are driven under the ore body at intervals determined by the height of the ore body above the haulage level. In order to minimize repair and maintenance, the

Jan 1, 1946

By M. E. Nicholson

The effect of boron on the austenitic transformation rate of iron is smaller than on low carbon steels. The influence of austenitizing temperature on B-Fe is the reverse of its influence on steels. THERE have been many studies made of the influence of boron on the hardenability of steel, but apparently none has been made of its influence on the y-a transformation of pure iron. There are several facts suggesting that boron should have a pronounced effect on the transformation rate of iron. First, Simcoe et a1.l indicated that boron reduces the nucleation rate of ferrite and bainite. Second, they showed, along with others,', " that the lower the carbon content of steel the greater the influence of boron on hardenability. If this trend extends to pure iron, the influence on rate of ferrite formation should be considerably greater for iron than for medium carbon steels. According to Rahrer and Armstrong," the multiplying factor for boron in pure iron should be about 2.40, compared with 1.50 in a 0.35 pet C steel. According to an extrapolation made by Grange and Mitchell,' the effect should be even greater, and the multiplying factor should be about 3.5 in iron. Many investigations of the boron influence'.7, 2, 5 indicated that boron is effective only when in solid solution. On the other hand, Chandler and Bredig" suggested that boron increases hardenability by combining with nitrogen, thereby preventing formation of AlN, which catalyzes the decomposition of austenite. If their hypothesis is valid, boron should have no effect on an alloy free from nitrogen. Digges et al." showed that so far as low nitrogen high purity Fe-C alloys are concerned this is not the case. No experiments, however, have been made on low nitrogen iron. To determine whether or not boron has an effect on low nitrogen iron and, if an effect exists, to determine whether it is as large as predicted from the investigations of boron treated steels, the following work was performed. Because of the rapidity with which iron transforms from austenite to ferrite at even a moderate degree of supercooling, it was decided to study the influence of boron on the transformation rate of iron by determining the effect of quenching rate on the temperature of the beginning of transformation. The technique, essentially that used by Greninger' and Duwez,H consisted of heating small specimens, 0.1 in. sq and 0.010 in. thick, in an atmosphere of purified helium with a resistance heater coil, and then quenching the sample in a jet of helium gas. At the time the jet was applied, the heating coil was removed from around the sample. The sample was suspended in the furnace on 30 gage chrome1 and alumel wires, one welded to each side of the specimen, which also served as a thermocouple for measuring the specimen temperature. Specimens were prepared from vacuum-melted iron obtained from the National Research Corp. which was rolled to a thickness of 0.060 in. and then decarburized in wet hydrogen for 51/2 hr at 700°C. This treatment also removed any boron present in the iron. The resulting iron contained 0.001 pet C. 0.0002 pet N, and 0.005 pet 0. One half of the piece was then boronized by surrounding it with 325 mesh boron powder and heating it for about 2 hr at 900°C in H,. The boronized iron was then homogenized at 1100°C for 24 hr. The iron boride case formed by boronizing was removed by grinding 0.010 in. from each side of the plate, and the piece was finally rolled to a thickness of 0.010 in. The resulting alloy contained

Jan 1, 1957

By C. F. Cornell, R. C. Emmett, D. A. Dahlstrom

FOR many years the disk-type and cloth-covered drum filters have found widest application in liquid-solids separation, which uses continuous filters. The disk type is less expensive, occupies less floor space per square foot of filtration area, and re- quires negligible down time for filter media changing. However, because filter cloth is billowed out by the blowback in the cake discharge, it is very short-lived if the scraper blades are set too close. Consequently cake weight is very important in assisting cake discharge, which normally necessitates a minimum cake thickness of 3/8 to ½ in. Also, the vertical position of the disks eliminates the possibility of efficient cake washing for removal of soluble values. The disk-type filter is generally limited, therefore, to applications that require no cake washing and form relatively thick cakes within the normal range of filter cycle times. The conventional cloth-covered drum filter is a more flexible unit, permitting wider variation in the percentage of cycle time devoted to cake formation, dewatering, or washing, as required by the application. Thinner filter cakes can be discharged be- cause a horizontal line across the filter medium at the location of the scraper blade is equidistant from the edge of the blade at all points. The scraper blade therefore may be set a short distance from the filter medium or, where wire winding is not used, a floating scraper can be utilized so that the contour of the cloth can be followed. The drum filter is generally employed when there are difficult filtering slurries with resultant thin cakes or when cake washing to recover soluble values must be practiced.

Jan 2, 1958

By W. N. Hiatt

The mathematical theory of the flow of two-phase, incompressible fluid through porous media is clarified, and the development of a general fluid displacement equation for two-phase, incompressible vertical flow through porous media is outlined. The relationship between the three components of the equation — the "fluid drive effect", the "gravity effect", and the "capillary effect'' — is discussed, as well as implications of the analysis in connection with the study of certain types of petroleum reservoirs. INTRODUCTION The purpose of this paper is to clarify and summarize the mathematical basis of the theory of two-phase incompressible fluid flow through porous media, particularly as it pertains to vertical flow, and to present a qualitative* exposition of the controlling factors involved in circumstances where this type of flow may exist. Although the generally accepted theory of heterogeneous fluid flow through porous media was developed a number of years ago by Muskat,1 and Buckley and Leverett2, 3 using the basic premise of Darcy, (and since then expounded upon by many others) there is a need for an over-all summary and clarification of this theory, especially regarding certain types of applications in connection with so-called "gravity-drainage-type reservoirs". The source and derivation is outlined for what is referred to here as the "General Fluid Displacement Equation for Incompressible Vertical Two-Phase Flow through Porous Media''. This equation would apply under the condition where the pressure drop along the path of flow is negligible in comparison with the pressure level on the system, or where compressibility and solubility effects are negligible. These conditions exist ordinarily in gravity-drainage-type reservoirs. Specifically, it will be shown that this general equation may be developed directly from the basic equations, which, according to present theory, govern the general case of viscous heterogeneous flow through porous media. This general equation has appeared in the literature previously, but in most cases its development from basic theory is not indicated clearly, or the equation is presented in terms of groups of constants and variables involving reduced or dimensionless quantities. This presentation is expedient in cases of experimental or computer applications; but it may make it difficult for the practicing petroleum engineer to identify all the factors involved or to understand the relationships between them. Therefore, in the following development, only ordinary mathematical parlance will be used, and no terms involving groups of other equations or reduced or dimensionless quantities will be used. DERIVATION The following equations for two-phase oil and gas flow result from analogy with Muskat's general equations,** if solubility and compressibility effects are neglected, and if all volumes are considered in terms of reservoir conditions, and the water phase, if present, is considered to be immobile (or effectively a part of the porous medium.) In this case, the sum of the oil and gas saturations may be taken as unity, and the saturation of each phase is in terms of the total hydrocarbon saturation. Note that in Eqs. 1 and 2, and in the derivation following, z is taken as positive in the vertically downward direction,

Jan 1, 1969