Search Documents

By Henry H. Angst

Tim history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. The elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,000 tons of ore and 18,000 tons of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4 1/2-cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. EQUIPMENT On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-dump trucks rather than smaller trucks, for the following reasons: I. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4 ½ -cu, yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1941

By George A. Roberts

The development of an alloy system, high-speed steel, is used as an example of the progress of physical metallurgy. Tracing the history of men and their thoughts as they studied and invented and modified these materials, the story of high-speed steel since the 1890's is seen to be a long, slow, but steady progression of achievements. Today's multiplicity of high-speed steels are the result. Data are presented on quantitative metallography of carbides in high-speed steel with high vanadium content using the QTM instrument. Grindability as well as mechanical properties are related to the content of excess MC and M6C carbides in a series of high-speed steels and the newer matrix steels. These emphasize the present state of knowledge and show the current stages of thought that may affect the development in succeeding years. It is a great thrill for me, an ex-research metallurgist and ex-practicing metallurgical engineer, to speak to an audience currently engaged in both pursuits on the occasion of the 43rd Howe Memorial Lecture before the Iron and Steel Division of the AIME. I shall not review Henry Marion Howe's distinguished career, so adequately reviewed in Maxwell Gensamer's contribution in the 1965 AIME History of Metallurgy, except to point out that, while leading the life of an intellectual, he worked as a practicing research metallurgist and a practicing metallurgical engineer for significant periods of time and contributed greatly in both areas. For those of you who believe, as I do, that in the intellectual activity of metallurgy we are blessed with an intimate mixture of science and engineering (see Mehl's 1960 Howe Lecture), we might recall that Howe, while pursuing a life of writing and teaching in later years, served as the first Chairman of the Division of Engineering of the National Academy of Sciences. That metallurgists were called upon then to lead an engineering recognition movement is perhaps related to the strong part played by the AIME and its members in the recent establishment of a National Academy of Engineering and to the fact that a metallurgist is its head, 47 years after Howe served. I stress these engineering aspects for I wish to talk about a metallurgical engineering subject today. Alloy systems, physical metallurgy, and steel blended with an historical perspective and a report on new techniques to improve the old will, I trust, be of sufficient interest to bring these lectures back to the physical-metallurgy banner from which they have departed for 4 years. Those process metallurgists, open-hearth fiends, and physical chemists among you will just have to be patient. The development of an alloy system is the engineering application of scientific thought and fact. There are many interesting alloy systems, developed to a high degree of technology and sophistication over the past 40 to 70 years. These systems are bound together and related by a similar set of characteristics. For example, stainless steels are a system in which the members are related by a high chromium content which gives a corrosion-resistant characteristic. A subfamily in this system would be austenitic steels

Jan 1, 1967

By Fred W. Gordon

The North Chicago Rolling-Mill Co., of Chicago, have four furnaces at South Chicago, built during 1881. Each furnace is 20 feet diameter of bosh, and 75 feet total height, the hearth being 11 feet diameter, and the top 15 feet 4 inches. They are blown through seven 7-inch tuyeres placed 5 feet 6 inches above the hearth level. Cubical contents, 15,000 cubic feet. Each furnace is supplied with 2 blowing engines, 84-inch blowing cylinder, and 36-inch steam cylinder, and 54-inch stroke. These two have one jet-condenser worked by an auxiliary pump. The blast for each furnace is heated by the aid of three Whitwell fire-brick stoves, each 21 feet diameter and 60 feet high. In the batteries of boilers furnishing steam for four furnaces there are 36 double-length boilers, 76 feet long, 48 inches diameter and 16,000 square feet heating-surface. The plant was designed to produce 3600 tons per week, or 900 tons for each furnace, and was fitted as above with such engines, boilers, and hot-blast stoves as were thought requisite for that production ; hence, calculated from the present make—not the least remarkable feature is the economy of construction—there are less engines, less boilers, and less hot-blast power for the iron made than at ally plant within my knowledge, or it could to-day be duplicated for less money per ton of iron made per week than could any plant now in existence, whether using fire-brick or cast-iron stoves for heating the blast. This is a practical demonstration of my assertion in a paper on fire-brick stoves, read before the Institute," that the application of fire-brick stoves in construction really lessens the first cost. In view of the statements just made, I must be most emphatic in assuring the members that nothing is strained or overburdened.

Jan 1, 1886

By Herbert Clark Hoover, Lou Henry Hoover

SINCE I have written of the varied work of pre- paring the ores, I will now write of the various methods of smelting them. Although those who bum, roast and calcinea the ore, take from it something which is mixed or combined with the metals ; and those who crush it with stamps take away much ; and those who wash, screen and sort it, take away still more; yet they cannot remove all which conceals the metal from the eye and renders it crude and unformed. Wherefore smelting is necessary, for by this means earths, solidified juices, and stones are separated from the metals so that they obtain their proper colour and become pure, and may be of great use to mankind in many ways. When the ore is smelted, those things which were mixed with the metal before it was melted are driven forth, because the metal is perfected by fire in this manner. Since metalliferous ores differ greatly amongst themselves, first as to the metals which they contain, then as to the quantity of the metal which is in them, and then by the fact that some are rapidly melted by fire and others slowly, there are, therefore, many methods of smelting. Constant practice has taught the

Jan 1, 1950

By Howard I. Smith

THE mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. 11o W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3.NaHCO3.2H2O). Pure trona contains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. ANALYSES Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells† and found to be exceptionally pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nightengale‡ for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO3.2CaCO3), which he named shortite,2 after Maxwell N. Short.* He analyzed the samples of trona, with the results shown in Table i. [ ] In addition to the 10 ft. I in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either mostly trona or some other soluble salt, but it should not be included in calculating reserves. In the part of the core between 1590 ft. 3 in. and 1600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. ACCOMPANYING MINERALS Fahey later secured about 600 ft. of the core for a detailed examination and study

Jan 1, 1942

By L. A. Schrider, J. A. Wasson

A method of predicting waterflood performance has been developed that combines certain facets of several previously published prediction techniques. The manner of combination has required the development and use of some new and some little-known relationships and has eliminated several of the weaker assumptions inherent in the original individual prediction methods. This approach, which was designed for computer solution, has removed the necessity of referring to plotted curves and permits the analytical prediction of water flood performance for a five-spot well pattern in either homogeneous or stratified reservoirs. The Predicted values are expressed in common oilfield units rather than in abstract or dimensionless terms. The calculation procedure has been programmed in FORTRAN IV and the entire program listing is available to potential users.* Introduction Prior to initiation of secondary recovery of oil by waterflooding, the possibilities of economic success or failure must be evaluated with the greatest practical accuracy. Although many prediction techniques are available, most, if not all, have serious limitations. In recent years, the Bureau of Mines has attempted to stimulate interest in the secondary recovery of oil from Appalachian pressure-depleted reservoirs. Waterflooding, because of its widespread acceptance and success, is the principal secondary-recovery method considered. During the life of the project, several performance prediction methods have been studied and applied. Because these methods, individually, have inherent assumptions and limi-tations, portions of some of them have been selected and combined in an effort to eliminate such shortcomings wherever possible. We believe that the resulting technique is as accurate as the necessary available data will permit and that it has several distinct advantages over previously published methods. Development of the Method The fractional flow equation developed by Buckley and Leverett' from Darcy's law is the fundamental mathematical statement describing immiscible fluid-fluid displacement in porous media. A generalized form of this relationship, whose derivation is readily available in the literature, is The formation dip, a, is usually very small in those petroleum reservoirs being considered for pattern waterflooding in the Appalachian area. Therefore. in many cases. a has an almist negligible value. In addition, Ap, the difference between the density of water and the density of oil, is relatively small. For these reasons the gravitational term may often be neglected. Capillary pressure is a function of saturation, which is in turn a function of distance from the upstream boundary of the system or the injection well. In this study it is assumed that the frontal zone of the waterflooding (or zone of capillarity) has negligible length and that only those saturations in the water-swept zone at breakthrough and later are of interest. As the distance in a waterflood pattern is comparatively large and the change in water saturation with distance is usually small, the change in capillary pressure with distance is negligible. The simplified form of the fractional flow equation is appropriate, therefore, in this application. Three variables must be considered in determining that fraction of the total fluid flow that consists of water: the viscosity ratio, saturation, and relative permeability ratio.

Jan 1, 1969

By Harmon F. Fisher

In the course of a comprehensive investigation for the development of the electrical process for the dehydration of oil-field emulsions, the writer has had an unusual opportunity to direct and execute a number of related, parallel studies concerning crude oil emulsions and extending over a period of nearly six years. Among these was an investigation utilizing the microscope for studying both the general characteristics of crude oil emulsions, the nature of their electrical charge and the action of an alternating current field in causing coalescence of the finely dispersed, more or less permanently suspended, emulsion particles into larger droplets of such mass that subsequent dehydration would follow by the ordinary process of settling, further agglomeration of the water droplets and, finally, separation into commercially dry, pipe line oil and a clean water discharge. It is not the purpose of this paper to enter into a detailed discussion of the highly specialized subject of microscope technique, nor into a theoretical discussion concerning the origin of the electrical charge on the emulsion particle or concerning the mechanism of the electrical phenomena occurring during the electrical treatment of oil-field emulsions. In a short paper of this character one can hope to touch on only a very limited discussion of the theoretical aspects of crude oil emulsions. The subject of emulsions and colloids is comprised in a comparatively young science in which, however, very rapid progress is being made and consequently it is undergoing many changes; a tentative conclusion valid today may be overthrown tomorrow. Nor would it be a simple science even if it were no longer undergoing this rapid progress; a thorough study of emulsions is based upon a knowledge of such fundamental subjects as molecular structure, ionization and other electrical phenomena, surface chemistry, surface and interfacial tension phenomena, viscosity and other factors too numerous to discuss here and the fundamental theories of which are still undergoing more or less change. Therefore this paper will confine itself largely to a generally descriptive discussion, a sufficiently detailed outline of the microscope technique and a brief comment on

Jan 1, 1931

By W. L. Penberthy, H. J. Ramey

Experimental work on the combustion oil recovery process has consisted of both laboratory and field studies. Although field experiments are the ultimate test of any oil recovery process, they are costly, time consuming and difficult to analyze quantitatively. Laboratory combustion tube experiments can be opertzted far more rapidly and cheaply, but are subject to scaling and interpretation problems. This paper points out some important design problems, operational criteria and considerations in2portunt to interpretation of results. An analytical hcut model of movement of a burning front axiully along a cylinder with heat loss through an annular insulation was developed. The result was used to identify steady-state temperatrrre distributions both ahead of and behind the burning front, with and without heat loss. Results indicate potential operating limitations on the minimum burning front rielocity (or air flux) which may be used for any given combustion tube. Results also enable estimating the effective thermal diffusivity and over-all heat loss from experimental data and thickness of the brnning zone. Resu lts of operation of a combustion tube constructed recently verify this preliminary theory in the region immediately ahead of and behind the burning front surprisinRly well. INTRODUCTION Many field and laboratory studies of the forward combustion oil recovery process have been conducted since the early publications of Kuhn and Kochl and Grant and Szasz2 in 1953 and 1954. In view of the complex and costly nature of this type of investigation, it is not surprising that no complete theory of the nature of the forward combustion Drocess is yet available. However, gross effects are understood well enough that reasonable design procedures are available for planning field operations. Nelson and McNeil 3,4 have published two comprehensive papers concerning design procedures. One major consideration in planning field operations is the fuel concentration at the burning front. Fuel concentration controls air requirements — an important cost factor in forward combustion. Although fuel concentration can be estimated from field test results by various methods, results are subject to great uncertainty in view of natural limitations on experimental observations. Nelson and hlcNeil4 recommend that fuel concentration be determined from laboratory combustion tube studies. Fuel concentration is only one of many important factors which can be studied by combustion tube experimentation. An obvious goal of imporrance must be development of a comprehensive theory of the forward combustion process. If a theory of this process can be established which matches controlled laboratory experimentation, it should be possible to apply this theory to field operating conditions with some confidence. Laboratory combustion tube studies have already yielded important information concerning the combustion process. However, details concerning the design, construction and operation of combustion tubes are rare. Combustion tubes used by various investigators vary in size, length and mode of operation. Therefore, one purpose of this paper is to present considerations important to design, construction and operation of a combustion tube. In regard to previous combustion tube studies, attention is called to Refs. 1 through 9. These references describe a wide variety of equipment types and present a great deal of pertinent experimental data. In general, combustion tubes usually consist of thin-walled stainless steel tubes containing an oil sand pack mounted within a pressure jacket. Provisions have often been made to heat the tube ex tern a lly by separately controlled heaters to reduce heat losses. This step usually permits operation at low air fluxes (air rate per square foot burning front surface) similar to those encountered in field operations. Burning is usually conducted from the air inlet end of the tube to the outflow end. The tube orientation used has been vertical or horizontal. For vertical tubes, burning has been conducted vertically downwards. As a result of laboratory studies, many of the

Jan 1, 1967

By Malcolm F. Hawkes

AUSTENITE grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, machinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to provide knowledge of the grain-size -characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstructures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The problem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will be considered first. More than So commercially produced cast steels representing a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules; namely, one hour at 1550°F, one hour at 1700°F, and six hours at 1700°F. The list of steels and results obtained on them will be found in the appendix. (See page 21.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT METHODS SUITABLE FOR DETERMINING AUSTENITE GRAIN SIZE AFTER HEAT- TREATMENT AT ORDINARY TEMPERATURES AND TIMES It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1947

By K. T. Koone, R. J. Blackwell

One of the more important problems to be solved in designing a miscible flood is related to the size of the solvent bank used. Size of the bank may be critical to economic success. Too large a bank loses money; too small a bank may deteriorate and fail to maintain the miscibility needed for high recovery. An important factor in deterioration of a small bank is permeability channeling. In a highly stratified reservoir, solvent speeds ahead in the more permeable zones and mixes laterally with fluids bypassed in adjacent, low-permeability strata. Numerical solutions have been obtained .for the differential equations that describe the movement of a slug through a two-layer system in which mixing occurs both in the direction of flow and transversely. The solvent slug is assumed to have the same density and viscosity as the resident fluid and the pushing fluid. These solutions have been verified by comparing them with similar concentration profiles obtained in the laboratory in a 36-ft stratified model packed with glass beads. The theoretical study revealed that when the dominant mechanism causing a bank to fail is lateral mixing the bank size needed for a given recovery may increase with length rather than decreasing as the square root of reservoir length, as suggested by one-dimensional mixing theory. From a comprehensive examination of the variables, a generalized correlation is developed that relates strata thicknesses, bank size, fluid velocity, mixing coefficients, system length and simple solvent-resident fluid phase behavior to the area miscibly swept. INTRODUCTION Miscible displacement, or solvent flooding, continues to receive widespread attention as a method for increasing oil recovery over that possible in conventional gas-drive or waterdrive projects. A basic economic requirement in the application of such processes is the use of as little solvent as possible. A basic physical requirement is that enough solvent be used to maintain miscibility. Economics places an upper limit on the size of a solvent slug, and physical considerations establish a lower limit. Consequently, the practicality of any given miscible process requires that the economic limit be greater than the lower limit imposed by physical requirements. Procedures exist for determining the economic limit; however, procedures for determining realistic minimum bank sizes exist for only special reservoir situations. In the past, bank size has usually been selected on the assumption of a piston-like displacement for which only longitudinal mixing is important. This assumption leads to the favorable conclusion that bank size, expressed as per cent of pore volume, is inversely proportional to the square root of length. Collins considered the problem of transverse mixing of solvent with fluids in bypassed zones with the assumptions that no forward mixing occurs and that the concentration is uniform in the permeable stratum of interest. 1 Lauwerier considered a mathematically similar problem in thermal recovery operations.2 Their work suggests the much less favorable conclusion that bank size could be directly proportional to the length or even higher powers of the length. This paper considers the physical behavior of a small solvent bank as it moves through a real reservoir, without imposing many of the restrictive assumptions of past treatments. To facilitate mathematical description, an idealized, two-layer model that permits mixing both laterally and in the direction of flow will be considered. A calculation procedure for solving the descriptive equations will be developed for a displacement involving fluids of equal density and viscosity. In addition, laboratory experiments designed to check the computational results will be described, and the coincidence of calculated and observed results will be discussed. The use of many solutions for a variety of bank sizes, strata thicknesses and characteristic system lengths to develop a usable correlation between

Jan 1, 1966

By Giovanni Barla, Stefan H. Boshkov

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The technique of calibrating gelatin mixtures proposed by Richards and Mark in 1966 is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example with the view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The prediction of the displacement, stress field and mode of fracture associated with a given rock structure, its initial stress field, and its physical properties is essential to rock mechanics and ground control. The basic approach is to assume the rock mass to behave as a continuous, homogeneous, and isotropic medium. The classical theory of elasticity is the simplest theory based on such a concept. Specification of the elastic constants, the initial state of stress in the ground, and the boundary conditions on stress and displacement allows one to predict stress and displacement within the body. Subsequently, provided that a criterion which governs rock fracture under various stress conditions has been established, a stability analysis of the rock structure can be performed. A natural extension of the present knowledge consists of removing some of the simplifying assumptions which characterize the analytical solutions based on the classical theory of elasticity. Complex geometry, the significance of tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space are some of the important factors which are neglected in the classical approach. A better insight into the real problem can be attained with either the finite element method of stress analysis or an experimental technique. The former has already been applied with success on several occasion 1-4 and is destined to render great service in the field of rock mechanics and ground control. The latter, which will be considered in this paper, has been used extensively in applications too numerous to be enumerated. Experimental technique involves either prototype testing, if the area to be studied is accessible, or model testing. Two- and three-dimensional photo-elastic analyses are very convenient means of obtaining the stress distribution in models of complex geometry. In general, such analyses are confined to studies of stress fields around openings which are sufficiently far removed from the surface boundary so that the stresses in their neighborhood are practically equal to those produced by an initial uniform stress field; i.e., so that gravitational effects are negligible. There are, however, many rock structures where these effects must be taken into account to attain a more realistic representation of the problem. Surface and near surface rock structures, systems of openings interacting with one another, and structural components loaded only by their own weight are some of the obvious examples. This paper was written to show how factors neglected in the usual analysis based on the classical theory of elasticity, can be taken into account when gelatin mixture models are used inconjunction with photoelastic methods. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with a view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The birefringence of gelatin mixtures has been known for some time. A series of experiments were carried out by Rossi in 1910,5 but after that very

Jan 1, 1970

By V. L. Elliott, C. L. Meyette

The conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a usable and relatively simple solution to a bothersome problem. Basis For Classifying In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will be used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined1 as a zone of

Jan 1, 1949

By V. L. Elliott, C. L. Meyette

The conditioning of semifinished steel products such as billets, blooms, and slabs to remove surface defects before further processing to finished products is a necessary accompaniment to steel mill rolling operations. A knowledge of the kinds of defects which occur and of the conditions in melting, teeming, and rolling that may lead to their occurrence is favorable to the production of quality products. Surface defects may be classed as either of mechanical origin such as those that occur in the heating and rolling operations and include breaks, tears, guide marks, mechanical laps and the like, or they may have been in the ingot before heating and rolling. Examples of the latter are ingot cracks, blow-holes, scabs, and inclusions which lead to the numerous known types of seams and surface flaws. Most of the common types of surface defects and methods for their identification by visual examination or by the aid of macro-etch tests are well known. The conditions which caused their formation are also appreciably understood and this knowledge has been instrumental in the establishment of methods for metallurgical control. There are, however, defects of doubtful origin. In any endeavor to trace the causes for their occurrence, the question of first concern is: I. Whether they were formed in the rolling procedure. 2. Whether they existed in the ingot prior to rolling. In the case of semifinished products which are rerolled to finished products there is also the question of whether they were formed in the primary or in the secondary rolling. In metallurgical laboratories where numerous or routine examinations of the quality of rolled products are made over the course of time, there will doubtless be many puzzling cases of defect origin. Microscopic examination of the defects may, however, reveal a characterizing condition that can be used to classify them broadly with respect to their origin. Such a condition has been observed and, after detailed investigation, is described here with the thought that it may offer a usable and relatively simple solution to a bothersome problem. Basis For Classifying In this discussion the term "mechanical type defects" will be used to designate those that have occurred as a result of the rolling operations such as in rolling from the ingot to billets, blooms, or slabs or in rerolling to finished products. The term "steel type defects" will be used to designate those that were present in the ingot prior to primary rolling or that were in the semifinished product prior to secondary rolling to finished product. The basis for distinguishing between the two types of defects lies in the relative degree of subscale formation surrounding them. Subscale is defined1 as a zone of

Jan 1, 1949

By Charles Fulton

EXPERIMENTAL work on the process was begun on a laboratory scale at Cleveland, Ohio, in 1914, and transferred to East St. Louis, Ill. in 1916, where a commercial sized furnace was in technical operation until January, 1918. The essential steps of the process are as follows: Oxidized zinc ore or roasted zinc concentrate is mixed with crushed coke and coal-tar pitch and formed into briquets 9.25 in. (23.5 cm.) in diameter and 21 in. (53 cm.) long in a manner similar to that used in the manufacture of graphite or carbon electrodes, except that much less care and time are required. The composition varies with the nature of the ore; in one case, the composition was 100 parts ore, 70 parts coke, and 18 to 20 parts pitch. These briquets maintain their form and volume during and after the distillation of the zinc. This object is gained by using coke as the matrix and coal-tar pitch as the binder; this pitch becomes coke on heating and unites the ore particle and the original coke particle into a continuous mass. The briquet is an electrical conductor but only to such, a degree that it can be used as a resistor. The size of the ore, as in the present practice of zinc metallurgy, ranges from fine material, such as flotation concentrate, to coarse table and fine jig concentrate. The process is not restricted to any particular kind of ore, but is applicable to pure high-grade ores, ores high in iron, and complex zinc lead ores, since the residue from the distillation is held immovably in place within the briquet. In the case of complex zinc-lead ores, the distillation is conducted with a carefully regulated temperature so that a high percentage of lead is retained in the distilled briquet, which may then be smelted for its lead content. In present zinc smelting practice, the reduction fuel is from 40 to 50 per cent. of the weight of the ore. In the briquet, it is from 60 to 85 per cent. of the ore; but unless the ore is exceptionally high in residue, the distilled briquet

Jan 9, 1919

By A. B. Kinzel

PRECISE knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metal-lurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each, temperature from room temperature to fusion tempera-ture, and cooled at a rate that is not generally controllable but is pre-determined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each tem-perature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and dis-advantages of the extent of the zone are of prime moment, and are dis-cussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly well known.

Jan 1, 1935

By D. M. Milne, R. F. Stoner, W. Bakiewicz

The Lower Indus Basin deposits form a substantial unconfined alluvial aquifer of excellent quality. This aquifer contains basically highly saline groundwater, overlain in places by considerable amounts of fresh water whose origin can be traced to the present and historical courses of the River Indus. In the past, the main source of groundwater recharge has been direct river seepage and water tables were generally deep. Since the establishment of a perennial irrigation regime however, deep percolation from the increased irrigation supplies has predominated and the water table has risen to within a few feet of the surface. The river system itself is being progressively devel-oped for irrigation and very shortly a situation will arise where the entire low winter flow will be utilized. Fresh groundwater will then be exploited to supplement the surface supplies, and at the same time a drainage system, mainly based on wells will be used to stabilize the water table at safe depths. This paper discusses some of the methods used to ensure optimum economic development of the fresh groundwater and describes the general design philosophy evolved by the authors' firms for both irrigation and drainage wells, with respect to both well configuration and operation. Water quality standards are discussed insofar as they affect subsequent use of the groundwater. A few particular aspects are considered, including the values of the relevant aquifer constants, the construction of wells, and the determination of screen losses. A major problem solved during the Lower Indus Project investigations has been the design of wells to produce fresh water from layers overlying saline water. This solution is also discussed. The recent interest in the groundwater of the Lower Indus Plains of West Pakistan has two main aspects. Firstly, soil waterlogging and the associated salinity hazards caused by rising water tables are a serious problem in agriculture, and the ease with which drainage requirements can be met by aquifer pumping makes this an obvious solution. The second interest stems from the rapid intensification of irrigation agriculture and the growing shortage of water supplies. In the areas where the groundwater is of suitable quality it can be used immediately for irrigation at relatively small cost and with large financial returns. In addition, the aquifer forms a potential storage reservoir which could be recharged from high river flows and depleted by pumping at times of scarcity. SOURCE OF GROUNDWATER The Lower Indus plain is a relatively long and narrow alluvial basin on a north-south axis, some 23,000 sq miles in area, bounded by higher land to the east and west. One hypothesis to explain the distribution and quality of groundwater in the region1 presupposes a river system considerably larger than, but very similar to the present river. This is characterized by a single mainstream, with subsidiary overspill channels in times of flood, running along the crest of a self-deposited ridge and with an extensive advancing delta. Sea water is contained in the alluvial pores of the advancing delta, forming the native groundwater. This has been partially displaced from two sources, namely direct seepage of fresh water from the river channel in meander flood plain areas and percolation from flood spillage in cover flood plain areas. Percolation has been subject to much re-evaporation and is thus slightly saline even as it reaches the groundwater. The whole complex has been further affected by two main influences: evapotranspiration from the land surface that tends to salinize the groundwater and down-valley flow that tends to bring fresher water

Jan 1, 1970

By J. T. Lapsley, I. I. Cornet, A. E. Flanigan, R. Hultgren, J. E. Dorn

WITH the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that procedures of heat treating common magnesium casting alloys be investigated systematically. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. Research on the solution heat treatment and aging of magnesium alloy AZ92, (formerly ASTM No. 17; also known as Dowmetal C or AM260) which was done under "Restricted" Project NRC-21, in 1942-1943, and reported, in detail in a final report to the OSRD on September 3, 1943, is the basis of this paper, which has been released for publication by the OSRD. American experience with magnesium alloys prior to World War II was limited, although some of these alloys had been in commercial use since 1909. Requirements of the aircraft industry for light alloys made it imperative to understand and utilize the advantageous strength-weight properties of magnesium castings. Magnesium casting alloys are commonly solution heat treated to increase their ultimate tensile strength and ductility; this treatment may be followed by an age hardening at elevated temperatures, which raises the tensile yield strength but diminishes the ductility. In the present investigation, AZ92 was studied to determine the effects on properties of various solution heat treatment and aging schedules. The principles of heat treatment of magnesium alloys are the same as for other non-ferrous alloys. The alloy studied, AZ92, has a nominal composition of 9 pct aluminum, 2 pct zinc, and minor constituents. Fig I shows, by the projection of isothermal sections on the concentration plane, the solubility surface1 of the ternary magnesium-rich solid solutions as determined by X ray analysis. From this figure it may be seen that above approximately 375°C (707°F), AZ92 alloy is a single phase alloy at equilibrium; below this temperature the equilibrium condition is a. two phase alloy. The beta constituent which precipitates from the solid solution exerts a hardening effect. Because the zinc concentration is only 2 pct, and because of its solubility relations, AZ92 resembles a binary alloy of magnesium with aluminum. The solubility curve1 of Fig 2 shows how rapidly the solubility of the beta phase decreases with decreasing temperatures. Unlike many aluminum alloys, magnesium alloys do not age harden at room temperatures; precipitation hardening of AZ92 alloy is performed at about 177°C (350°F). At this temperature about 3 pct aluminum

Jan 1, 1947

By Eugene S. Machlin

A classical theory of solid solutions involving neavest-nergkbor intevactions with both central and linked-central forces between atoms has been developed. It has been found that the theory, where it can be checked quantitatively, is in ageement with experiment. The theory encompasses a description of many diverse pkenomena, such as antiphase shift structures, size effect, relative stabilities of various solutions, lattice para,neters, and order-disorder transitions. In particulav. a quantitative prediction not involving adjustable pavameters is made concevning the deviation of the Au-Cu interatonlic distance in long-range ordered (Ll,) Cu-Au I fronl the average distance based on the distances in pure gold and copper. This prediction, which is in agreement with expel-intent, has not been encompassed by any preuious theory. The theory of order-disorder is fragmentary. That is, no one theory exists that can explain the variety of qualitative phenomena observed. Further, many theories are not in good quantitative agreement with experiment. This subject has been reviewed by Muto and Takagi, Tuttman, and Oriani.3 There exists no doubt that the quasi-chemical approximation is not a complete description and that the inclusion of strain energy using macroscopic elasticity theory concepts leads to results in disagreement with experimenL4 The observation of antiphase domains and ordering systems such as Cu-Pt has led to Brillouin zone treat-ment of the order-disorder transition as opposed to the classical Ising model. The objective of this paper is to demonstrate that it is possible to develop a pairwise approximation model that can explain many of the observed order-disorder phenomena that have puzzled investigators in the past. This theory is based upon an empirical model due to ergmman' for the elastic constants of metals. This model is generalized for multicomponent systems. As will be shown, the theory yields a short-range ordering energy for the disordered solution which differs from the ordering energy calculated from the differences in energy of disordered and long-range ordered solutions. It will be demonstrated that there is no necessary correlation between heats of formation and the tendency to order or between size effect and the tendency to order. Also, the existence of antiphase domains and iso-short-range-order systems that form superlattices (Cu-Pt) is predicted on the basis of the theory. Further, the relative stability of competing superlattices is calculable from the theory. If single-crystal elastic-moduli data are available for the pure components and one superlattice then there exists but one adjustable parameter in the calculation of lattice parameters for both the disordered and ordered solid solutions. In one special case, no adjustable parameters are required and a quantitative prediction is made. For the calculation of energies and partial order, there exists but one additional adjustable parameter, the pair-exchange energy V used in the quasi-chemical approximation (or the Ising model.) However, in these calculations, much more precise values are required for the single-crystal elastic moduli than available if the quantitative uncertainties in the predicted values of the energies are to be sufficiently small. THEORY ~er~man' has developed a model with which he was able to obtain fair agreement with experiment for the relations between the elastic constants for metals. This model which we shall call Bergman's model is a linear combination of his models I and 11. In effect, Bergman, in this model, considers that each interatomic distortion is composed of two components: a classical central force distortion with an associated central force constant and what we shall call a linked-central force distortion with an associated linked central-force constant. The linked-central force distortion component obeys the constraint that the sum of such distortions over all the bonds equals zero. No constraint is imposed on the classical central force distortion component. Bergman' derives the constraint on the linked-central force distortion on the basis of application of Pauling's relation between bond distortion and bond number to metals.ga This assumption is not logically necessary, however, and the Bergman model may be taken as a mathematical model for elastic constants, e.g., a purely empirical model without a physical basis. In the present work, the method of Bergman has been applied to two-component systems (solid solutions). In place of an external strain—which would allow a calculation of the elastic constants for the two-component system—it is considered that internal interatomic distortions exist as a consequence of having three potentially unequal distortion-free interatomic distances and but one "average" interatomic distance. It is assumed that the distortion-free interatomic distances between atoms of the same element are those found in the pure element having the same undistorted crystal structure as the solid solution. The distortion-free interatomic distance between unlike atoms is in general not measurable except in the probably nonexistent

Jan 1, 1967

By Joseph S. Malesky

The discovery and development of explosives mark one of the most important findings in the history of civilization. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. For these reasons explosives are rightfully referred to as the forerunner of progress. An explosive may be defined as a substance (usually a mixture) that, when flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents. HISTORY OF BLASTING WITH EXPLOSIVES At one time workmen obtained stone blocks for building by grooving the rock with crude picks, driving wooden wedges into niches in the rock, and pouring water on the wedges; the swelling of the wood forced out the blocks. As late as the 17th century, fires were placed against the face of rock to crack it, and water was sometimes dashed on the heated rock to shatter it by sudden cooling. The progress of our country is synonymous with advancement of the improved manufacture and extended use of explosives. Coal had been

Jan 1, 1981

By Arthur C. Simmons

Production of oil within the state of Pennsylvania in 1940 was slightly more than the 1939 total, and this increase was due entirely to the new flush Music Mountain field south and west of the main Bradford pool. The influence and magnitude of Music Mountain production will be separately described, inasmuch as it is an important producing unit within the state. Production Bradford Field The production listed herein for Bradford field includes only the part of the field that is within the state of Pennsylvania. Approximately 4000 bbl. per day, or 10 per cent of the total Production of Bradford field comes from Cattaraugus County, New York, and should properly be attributed to production obtained within the New York state area, although locally and economically the Bradford field, situated both in New York State and Pennsylvania, is included as a single statistical unit. The 1940 average production in the Bradford field was 34,831 bbl. per day, as compared with a daily average in 1939 of 35,340 bbl., or a decrease from 1939 of 509 bbl. per day. The decrease in production from the Pennsylvania portion of the Bradford field would have been more pronounced if a portion of the crude from the Music Mountain field were not included with the statistics for Bradford field. The decline can be attributed largely to the fact that more properties of lower average recovery were being drilled in 1939 and 1940 than in previous years, and apparently a subnormal amount of drilling occurred in 1938 and 1939, when about 2100 wells were drilled each year. The full effect of the 1940 drilling is not felt immediately and undoubtedly will affect the producing period of 1941. It appears probable that the water-flood area in the Bradford field has reached a definite peak unless some unusual economic condition should cause abnormal prices and an excessive rate of development such as occurred in 1936 and 1937. Virtually all of the production in the Bradford field was obtained by water-flooding methods, as natural or stripper wells are uneconomical and air and gas repressuring have not proved so efficient as water-flooding as a secondary recovery method. Central and Southern Pennsylvania Central and southern Pennsylvania produced a total of 4,604,763 bbl. of oil during the calendar year of 1940; that is, an increase over the 1939 total of 166,728 bbl. The daily average production was 12,581 bbl., or an increase over 1939 of 422 bbl. per day. Table I includes the total oil production for the state of Pennsylvania for the years 1937 to 1940, inclusive, and the daily average for each of these years. It is impractical to make a complete subdivision by districts, consequently the only segregation is the production from the Bradford field (within the state of Penn-

Jan 1, 1941