Search Documents

By Clarence P. Linville

It is recognized that, in all metallurgical operations, the greatest possible uniformity in all conditions is essential to the best results. It is the constant aim of metallurgists to secure this uniformity, and their success in this respect has been in many cases the cause of great advances in the metallurgical processes themselves. Of all such processes, the production of pig-iron in the modern blast-furnace is perhaps the most complex and the most difficult of control. Notwithstanding the great progress of recent years, there is still great difficulty in obtaining anything like uniform conditions and results in the manufacture of pig-iron. The reason is not far to seek. The ores vary in composition and physical properties, often carrying a varying amount of gangue material, unevenly distributed. The coke may vary in composition, cell-structure, moisture, hardness, and other properties. The blast, the weight of which far exceeds that of any other constituent, varies in its moisture-content and consequently in its chemical composition; and its temperature, by reason of the method of heating, is not uniform, but, besides varying from time to time with atmospheric and other outside conditions, has a maximum and minimum for every changing of stoves. Now, with regard to these variations, the modern demand for uniformity has been greatly aided. Chemical analysis has made it possible to select ores so that the composition of the charge can be kept fairly constant; coal may be obtained from a given field, and coked in the same kind of ovens under conditions which make the fuel practically uniform; the Gayley

Jan 1, 1911

E. A. Peretti (University of Notre Dame, Notre Dame, Ind.)—Mr. Deitz and Professor Halpern are to be congratulated on a fine piece of work which adds to our knowledge of precious metal—cyanide-solution reactions. I should like to offer the following comments: The authors state, "the rate plots were always linear, indicating a zero order reaction rate." This appears to conflict with the data of Fig. 6 which clearly show the rate to vary with the NaCN concentration. It seems to me that the rate curves are linear because of the experimental setup. The volume of solution is so large that over a three-hour period the change in NaCN concentration is very small. A rough calculation for the experiments of Table I where the initial NaCN strength was 0.0096 mol per liter show a change of NaCN concentration of about 0.0009 mol per liter at the end of three hours. In short, over the period of time that the experiment was in progress, the NaCN strength was practically constant; hence the rate of dissolution remained practically constant. Eq. 10, as written, specifies that 1 mol of H202 and 2 mol of hydroxyl ion are formed when 2 mol of silver react. Is this true? The effect of H,O2 on the rate was made in solutions having an oxygen pressure of 4.8 atm. Were any tests made in solutions containing hydrogen peroxide, but no oxygen? G. M. Willis (University of Melbourne, Melbourne, Australia)—The authors have shown that, under their experimental conditions of high O2 concentrations, the rate of solution of silver in aqueous cyanide solutions is controlled by diffusion of O2 or CN- to the metal surface. With diffusion control, it is generally not possible to obtain further information about the mechanism of a process.

Jan 1, 1955

By Joseph C. Platt

It is not the object of the present paper to give a description of the minerals found on Mine Hill, in Sussex County, N. J., nor even to touch upon all the forms of the ores named, but to place upon record and call to the attention of the Institute some interesting facts concerning them. In May, 1875, after the Dover meeting, some of the members visited this locality, and, no doubt, it is fresh in their memories, being one of the best known mineralogical points in our country. It will be only necessary to describe it very briefly. Mine Hill and Stirling Hill, in Sussex County, N. J.,—the former being at the village of Franklin Furnace, and the latter near Ogdensburg,—are the only localities in the State where zinc ores are found in workable quantities.* Mine Hill is the more northerly, and mineralogically differs from its neighbor, chiefly in having no hydrated ores to speak of, while at Stirling this deposit is considerable. At both points Franklinite, red oxide, and silicate of zinc occur in large quantities. Mine Hill lies on the east side of the Wallkill River, above which it rises to an extreme elevation of about 150 feet. On the summit the outcrop of the Franklinite vein appears, while the lowest worked points are perhaps 10 or 15 feet above the level of the stream. Cornmencing at the northern end, where the Hamburg Road crosses it, this outcrop runs along the northwestern brow of the hill a distance of about 2000 feet, in a general southwest direction, to a point where is a large, cavern-like opening, called the "Southwest Opening." " Double Rock," about the highest point on the hill, lies near the middle of this 2000 feet of outcrop, and over or near it passes a property line, to which allusion will hereafter be made. At the Southwest Opening the vein bends abruptly towards the east,—the angle between the two parts being perhaps 45°,—and this easterly branch continues some 700 feet. From the northern part of the Stirling Hill deposit to the southern part of the Mine Hill deposit is about two miles, and in this interval the vein carrying Franklinite

By Gordon H. Geiger, John M. Svoboda

One mechanism of metal penetration into mold aggregates by cast steels is vapor state mass transport. In order to further understand and quantify this mechanism, the steady-state diffusion of metallic vapors was studied at 1250" to 1600°C in controlled oxygen pressure atmospheres by measuring the weight loss from a metal bath whose vapors were allowed to diffuse through a porous aggregate compact held at constant temperature. Mass transport rates substantially greater than those predicted from the assumption that the vaporizing species was the elemental metal vapor were observed. Vaporization rates were found to increase with an increase in the oxygen partial pressure in the gas atmosphere with maximum vaporization occurring at oxygen partial pressures just below those in equilibrium with a liquid oxide layer at the given temperature. When the liquid oxide layer was present, no vaporization was observed. Metal carbonyls were ruled out as the vapor species involved because of their thermodynamic properties. The species with the enhanced volatility were deduced to be gaseous metal-oxygen molecules, probably the polynuclear oxides (FeO)2 and (Mn0)2. Diffusion followed the ordinary diffusion mode, and Knudsen diffusion is not important in normal foundry molds. The interdiffusivities of the metallic vapors and the mold atmosphere, through the porous aggregates, were measured. The effective interdif-fusivity of the vapor species and mold atmosphere through the aggregate may be expressed as follows: Deff,12 - — where E is the void fraction of the aggregate and 7 is the "tortuosity factor". Aggregate material had no effect on diffusion rates, and the only relevant parameter was the void fraction. Values for 7 ranged from 3 to 6 for normal foundry aggregates with 4 being considered a good representative value. An area of interest in high-temperature metallurgical processes which has received little attention in the past is the diffusion of metal vapor species in porous aggregates. Research into the metal penetration phenomenon' in foundry molds has shown that a major penetration mechanism is the vapor transport of metallic species into the porous foundry sand molds, followed by condensation of metallic films on the sand grains. Considerable study of the vaporization of metallic species has been reported in the literature, and the vapor transport properties of many metallic species have been determined.2'3 Many instances have been observed where the vaporization behavior could only be explained by the existence of a metallic species with a vapor pressure greater than the elemental metallic species. These species were identified or, in some cases, presumed to be carbonyls,4,5 hydroxides,6-9 or vaporous oxides.10-16 The diffusion of gases through porous aggregates has received considerable attention in the literature pertaining to catalysis, although primarily at low temperature, and more recently in the literature concerned with ore reduction.17-22 The following experiments were devised and carried out in order to determine the nature of the metallic species involved in the metal penetration phenomenon, and the effective diffusivities involved. EXPERIMENTAL APPROACH Steady-state diffusion was selected for experimental convenience. The experimental systems used, shown in Figs. 1 and 2, consisted of a porous aggregate specimen contained in an impermeable alumina tube held above, and just separate from a metal bath. The entire system was held at constant temperature and pressure in a furnace with a controlled oxygen partial pressure atmosphere. After a brief period of nonsteady state behavior, a steady flux of metal vapor through the porous aggregate will develop due to the concentration gradient of metallic vapor in the gas phase. The flux of metallic vapor from pressure may be neglected because there is no pressure gradient. There is no flux from convection because there is no net flow of gas within the metal-aggregate system, and thermal diffusion is negligible compared to the flux from ordinary diffusion. If the material being studied is allowed to vaporize until steady-state behavior is attained, the experimental results may be analyzed using Fick's First Law.

Jan 1, 1970

By Samuel M. Cassidy

The exact date of man's first use of coal is lost in antiquity. The discovery that certain black rock would burn was undoubtedly accidental and probably occurred independently and many times in the world over thousands of years. It is quite likely that these independent discoveries were made when primitive man chanced to build camp fires on exposed ledges of a black rock, then was amazed when it caught fire. The Chinese recorded the use of coal 1100 yearn before the Christian Era and from the Bible we learn that King Solomon was familiar with coal in what is now Syria. In Wales, there is evidence that the Bronze Age people used coal for funeral pyres, and it is known that the Romans used this fuel. There are other ancient references. So the knowledge that coal would burn, and even some uses of that knowledge, go back thousands of years. However, practical and consistent use of coal seems to date to England in the Middle Ages. COAL IN AMERICA In the Americas, there is evidence here and there of occasional use by the Indians. However, the first recorded discovery of coal, in what is now the US, was by French explorers, who reported an outcrop exposure on the Illinois River in 1679. Following this, other discoveries were made by French and British explorers, but the first recorded actual usage was in Virginia in 1702, where a French settler was granted permission to use coal for his forge. Earliest recorded commercial mining was in 1750, from the James River coaEeld near Richmond, VA, a deposit now abandoned. Besides local consumption from this field, shipments were made to Philadelphia, New Pork, and Boston. During the Revolution this coal was of impor- tance in the manufacture of shot and shell; so important, in fact, that the British sent an expedition in 1781 to destroy the iron works and

Jan 1, 1981

By R. H. Sweetser

There are probably as many variations of the method for blowing-in blast-furnaces as there are furnace superintendents. That some of these variations are poor practice is shown by the troublesome and sometimes disastrous experiences of many furnace-men, even within the last few years. It is the object of this paper to put on record a blowing-in practice that has gradually developed to the point where the results are sure, safe, and satisfactory; and also to bring into discussion several variations that are questionable. The blowing-in of a modern blast-furnace is one of the greatest of metallurgical operations. On its degree of success depends much of the future life of the lining and the subsequent behavior of the furnace; and it involves possibilities of danger to the men engaged in the work. The objects to be attained are the heating of the interior of the furnace to the high temperature necessary for smelting iron; the starting of the smelting process; and the gradual movement of the stock in its downward course. The most critical points are the placing of the kindling-wood, the " bringing down " of the gas, the closing of the iron-notch, and the first cast. The lighting of the first gas, the opening of the cinder-notch for the first flush, and the running of the first cast are anxious times for the superintendent and the furnace-men. Drying-Out the Furnace. As soon as a furnace-lining is completed it should be thoroughly dried out, whether it is to be blown-in soon or not; and the longer it is dried, the better for the furnace. At least two weeks is desirable; but good results can be had with 10 days of firing. The crudest and least desirable method of drying is to build a wood fire in the bottom of the furnace, throwing the wood in through a tuyere-arch, and using the iron-notch for

Jan 1, 1913

By Howard S. Bryant

The state of Kansas in 1931 continued to hold fourth place on the list of oil-producing states, despite the fact that low prices for crude oil curtailed drilling to just one-half the amount done in 1930, which itself was the lowest in the preceding 10 years. The estimated crude oil production for 1931, according to sources available to the writer, will approximate 37,037,000 bbl., the lowest since 1925. Thus Kansas produced one-eighth less oil this year than it did last year when it produced 42,729,085 barrels. This year's development was characterized by a very small amount of wildcat drilling; however, large new areas were semiproven for oil production, and several thousands of acres were added to the actually proved areas in western Kansas, so that the state now has larger proven areas of oil reserves than at any time in its history since the heyday of the famous El Dorado pool. The general prospects for oil production in the near future are indeed promising for central western Kansas, where drilling costs are moderate and depths are relatively shallow compared to the remaining unexplored parts of the northern Mid-Continent area. Probably the greatest singular achievement in the state for 1931 was the development of its natural gas reserves. This development took place principally in two spots, McPherson County in central Kansas, and Stevens and Morton counties in southwestern Kansas, and it is a matter of record that more than one and one-half billion cubic feet of open-flow capacity per day were added to reserves, nearly twice the amount developed in 1930, previously the largest amount in the history of gas development in Kansas. Gas pipe lines already built and now building are in position to deliver natural gas by one system to Chicago, Ill., by another to Indianapolis, Ind., from whence lines already lead practically to the Atlantic seaboard, and to other cities large and small located west, northwest, north and northeast of Kansas. Table 2 shows all well completions for 1931 in a form to compare with the results of previous years.

Jan 1, 1932

By William Ward

ONE often reads of the rich placer gravels in many of the canoe-traveled rivers of South America. The apparent richness of these gold-bearing gravels impresses the traveler, and in fact he may see batea after batea showing enough colors to figure over a dollar per cubic yard. These workings are called "playas" from the Spanish word playa, meaning shore or beach. Many workings have been reported in tropical rivers, but to my knowledge no dredge has made a success in such deposits. Investigation generally shows that the area of richness is limited and especially that the depth of the rich concentration is hardly ever more than a few inches. The Cauca river in Colombia, South America, is noted for its many rich playas.. This river rises near Popayan in the southern part of Colombia, flows north through a narrow valley between parallel mountain ranges and empties into the Magdalena river near Maganque. The airline distance between source and mouth of this river is only about 500 miles. The rainfall is large and the lower Cauca appears to be about the size of the Missouri river in the United States. From its mouth up to Valdivia, in the State of Antioqua, it is navigable. Above Valdivia is a. narrow gorge, above which the river is again navigable for some distance. The part of the Cauca where the playa panning is most noticeable is from Valdivia down to Where the Nechi river enters the Cauca, a distance along the river of about 100 miles. The current in this part is swift, so that the stern-wheel river steamers make the trip with some difficulty. In the course of my work in this section of Colombia I have had the opportunity to make a study of several of these playa workings and will give in detail the conditions observed.

Jan 7, 1914

By Grover J. Holt

A DETAILED description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in I920, and subsequent developments have been described by E. E. Hunner,1 M. H. Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,3 it will not be necessary here to do more than review the highlights of current practice. Details on any points of interest can be obtained through correspondence with the operators involved. [T] The iron ores of Minnesota, which have been formed through enrichment of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and "paint rock," directly below the surface material and overlying the ore. Taconite is the iron formation, a ferruginous chert with interbedded slate layers. "Paint rock" is a local term for oxidized slate layers interbedded in the iron formation, high in phosphorus, alumina and moisture. The iron ores fall into two classes: (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite). The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high-manganese black ores, with some iron ore. The Vermilion Range yields mainly Besse¬mer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden¬-removal and shaft-mining costs. STRIPPING PRACTICE Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer. In the present emergency many operators are forced to forego the economies attained by year-round utilization of equipment and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be over-equipped and high depreciation charges will have to be absorbed.

Jan 1, 1942

By Arthur C. Simmons

The State of Pennsylvania produces approximately 60 per cent of the total production of Pennsylvania Grade oil, and naturally represents the dominant factor in the area producing that grade. The producing area comprises the states of New York, Pennsylvania, West Virginia, and a small part of Ohio. The importance of this area is too commonly neglected because it produces only 2 per cent of the total amount of crude produced in the United States. It is, of course, unimportant in its percentage of total crude production, but extremely important for its production of lubricating oil. The lubricating fraction from a barrel of Penllsylvania Grade crude oil represents about 22 per cent of the total, whereas the lubricating fraction from the total United States production represents only about 2.5 per cent of the crude oil. The Pennsylvania Grade area produces about 6,000,000 bbl. of lubricants, which is 15 to 20 per cent of the total produced in the United States. All Pennsylvania Grade lubricants are classified as "high-grade," and with a production of 15 to 20 per cent of the total lubricants, it appears probable that the Pennsylvania Grade area accounts for 25 to 50 per cent of the high-grade lubricants produccd in the United States. Production Bradford Field The production figures quoted in Table I apply only to the part of the Bradford held that lies wholly within the state of Pennsylvania; approximately 15 per cent of the Bradford field is in Cattaraugus County, New York, and 10 per cent of the production is obtained from that sector. The Bradford-field production in 1941 was 12,729,900 bbl. as compared with a production in the year 1940 of 12,748,279 bbl., or a reduction of 18,379 bbl. The year 1941 represents the fourth successive year in which production in the Bradford field has declined. All of the production from the Bradford field is obtained by water-flooding methods and increases or decreases in production are due more to economic factors than to any physical limitations of the pool, inasmuch as additional drilling of water-intake and producing wells would increase the total production of the field. It is apparent that increased drilling of oil and water-intake wells does not take place except under stimulps of a favorable price; and while oil prices during 1941 were moderately favorable, they were not sufficient to prevent a mild decline. Too many wells were drilled in the Bradford field in 1937, but this was compensated by subnormal drilling activities in 1938 and 1939 and a large increase in 1940, The increase in 1941 over 1940 was about 7 per cent. The effect of new drilling is becoming less pronounced on a per well basis because more properties yielding less per acre are being drilled than were drilled in former years. Central and Southern Pennsylvania The production in central and southern Pennsylvania amounted to a total of

Jan 1, 1942

By Arthur C. Simmons

The State of Pennsylvania produces approximately 60 per cent of the total production of Pennsylvania Grade oil, and naturally represents the dominant factor in the area producing that grade. The producing area comprises the states of New York, Pennsylvania, West Virginia, and a small part of Ohio. The importance of this area is too commonly neglected because it produces only 2 per cent of the total amount of crude produced in the United States. It is, of course, unimportant in its percentage of total crude production, but extremely important for its production of lubricating oil. The lubricating fraction from a barrel of Penllsylvania Grade crude oil represents about 22 per cent of the total, whereas the lubricating fraction from the total United States production represents only about 2.5 per cent of the crude oil. The Pennsylvania Grade area produces about 6,000,000 bbl. of lubricants, which is 15 to 20 per cent of the total produced in the United States. All Pennsylvania Grade lubricants are classified as "high-grade," and with a production of 15 to 20 per cent of the total lubricants, it appears probable that the Pennsylvania Grade area accounts for 25 to 50 per cent of the high-grade lubricants produccd in the United States. Production Bradford Field The production figures quoted in Table I apply only to the part of the Bradford held that lies wholly within the state of Pennsylvania; approximately 15 per cent of the Bradford field is in Cattaraugus County, New York, and 10 per cent of the production is obtained from that sector. The Bradford-field production in 1941 was 12,729,900 bbl. as compared with a production in the year 1940 of 12,748,279 bbl., or a reduction of 18,379 bbl. The year 1941 represents the fourth successive year in which production in the Bradford field has declined. All of the production from the Bradford field is obtained by water-flooding methods and increases or decreases in production are due more to economic factors than to any physical limitations of the pool, inasmuch as additional drilling of water-intake and producing wells would increase the total production of the field. It is apparent that increased drilling of oil and water-intake wells does not take place except under stimulps of a favorable price; and while oil prices during 1941 were moderately favorable, they were not sufficient to prevent a mild decline. Too many wells were drilled in the Bradford field in 1937, but this was compensated by subnormal drilling activities in 1938 and 1939 and a large increase in 1940, The increase in 1941 over 1940 was about 7 per cent. The effect of new drilling is becoming less pronounced on a per well basis because more properties yielding less per acre are being drilled than were drilled in former years. Central and Southern Pennsylvania The production in central and southern Pennsylvania amounted to a total of

Jan 1, 1942

By G. Meyrick, H. W. Paxton

Observations on the tensile deformation of single crystals of austenitic stainless steels as a function of composition, orientation, and temperature are described and compared with relevant data for other alloys. Crystals free from second phases show sharp yield points followed by Lüders' extensions of up to 20 pct. The critical resolved shear stress is strongly temperature-dependent increasing fourfold between 423O and 77°K. A temperature-independent low rate of hardening follows the Luders' extension and is frequently associated with overshoot. Unlike pure metals where Proficse cross slip usually occurs at the end of linear hardening, this stage is terminated either by cross slip or by slip on the conjugate system, the particular node apparently depending upon initial orientation and composition. The presence of 6 ferrite or martensite has a profound effect upon the magnitude of the yield stress and the shape of the stress-strain curve. In experiments on transgranular-stress corrosion cracking of austenitic stainless steels in boiling magnesium chloride, several workers1'2 have shown that increasing amounts of nickel tend to reduce the probability of specimen failure. Reed and paxton3 have observed in single crystals that the macroscopic crack plane changes as the nickel content is increased. For 18 pct Cr-8 pct Ni, the crack plane is sensibly perpendicular to the applied tensile stress; for 20 pct Cr-20 pct Ni the crack plane is (100). The average crack-propagation speed is much lower in the 20 pct Ni crystals. Furthermore, the possible importance of stack-ing-fault energy in nucleation and growth of cracks has been suggested by a number of workers. While the general effect of variations in stack ing-fault energy appears to be quite well-correlated with observed variations in cracking characteristics, each of the theories assigns rather different detailed reasons for these effects. Because the stack ing-fault energy of austenitic steels is believed to be increased with increasing nickel content, and because some theories of trans-granular cracking postulate a mechanical stage in the crack propagation (rather than relying entirely on electrochemical solution), it appeared to be of some interest to investigate the mechanical properties of a series of different compositions of aus-tenite single crystals. These experiments were considered of intrinsic value in view of the relative scarcity of such data on fcc alloys. This paper gives the results of some experiments carried out with this aim in mind, and suggests various 'other experiments which may be helpful in future studies. The experiments are also of interest in view of the recent interest in obtaining higher-strength steels by control of the imperfection content of austenite; although the compositions are not directly comparable, the results are still probably valuable. Comparisons with experiments on other fcc alloy crystals are made where possible to see how well the general pattern of behavior is understood. EXPERIMENTAL PROCEDURE The alloys used in this investigation were vacuum-melted heats of nominally 20 pet Cr-20 pet Ni-60 pet Fe, 20pctCr-16 pct Ni-64 pct Fe, and 20 pctCr-12 pet Ni-68 pet Fe.* Analyses of the material are

Jan 1, 1964

Vermont State Geological Survey, Burlington, Vt. G H. Perkins, State Geologist Most of the file reports of the State Geologist of Vermont were destroyed in a flood at Montpelier two or three years ago Full sets of 17 volumes may be seen only in libraries. The Annual Report for 1928 and the Annual Report for 1930 may still be had, as well as a few copies for the following years: 1901-2, 1907-8, 1909-10, 1915-16, 1921-22, 1923-24. These are distributed without charge. Flood-damaged copies of the two vols, Geology of Vermont, by Hager and Hitchcock, cost $3 plus postage For any of these volumes address State Librarian, Montpelier, Vermont.

Jan 1, 1933

At a meeting of the Board of Directors, held Jan. 21, 1916, the following resolution was adopted: Resolved, that this Board has learned with indignation and sorrow of the unprovoked and brutal murder of 18 American citizens on January 10, in the State of Chihuahua, Mexico, and laments especially the death of Messrs. C. R. Watson, C. A. Pringle, H. C. Hase, and W. J. Wallace, who were members of the American Institute of Mining Engineers. As these men and their companies were engaged, in the lawful prosecution of their work, we trust that nothing will be allowed to prevent or delay appropriate action by our Government concerning the outrage by which they lost their lives;

Jan 3, 1916

By Daniel M. Bass, Paul B. Crawford

Laboratory investigations have been made to study the effect of variations in fluid characteristics, gas saturation, water saturation, and water injection rate on oil recovery by water flooding. Three synthetic gas-saturated crude oils having bubble points of 860, 1,540 and 1,885 psi were used as reservoir fluids. Repeated tests were made in which a and pack, saturated with water and synthetic oil, was produced by solution gas drive followed by water flooding at various pressure levels. Oil recovery by solution gas drive and subsequent water injection is shown to vary with the pressure and rate at which the water flood is conducted. The pressure at which optimum flooding conditions exist is shown to be a functiotl of the physical characteristics of the reservoir fluid. For the systems studied, increases in oil recoveries of near 10 per cent were obtained by flooding at the most desirable conditions. Va- riations in initial water saturations gave results similar to those in the literature. INTRODUCTION Most of the waterflooding studies investigating means of improving present exploitation processes have been conducted at low pressures with little effort to simulate reservoir conditions. Holmgren and Morse' performed a waterflooding study at 300 to 500 psi wherein the gas saturation was created by injecting gas, letting dissolved gas evolve from the oil, and then flushing the core with "live" oil until the desired gas saturation was obtained. Their results show increasing oil recoveries with increasing gas saturations. Data presented by Guerrero' and Kennedy, et al, indicate that in some instances water flooding at approximately 500 psi below the original bubble point results in a lower residual oil saturation than is obtained when water flooding above the bubble point. In their work gas saturations were created by primary depletion. By correcting low pressure flooding data for fluid shrinkage, Dyes found that a maximum oil recovery may be obtained by flooding with initial gas saturations of from 7 to 12 per cent. The purpose of this work was to determine the variations in oil recovery caused by initiating a waterflooding program at various stages of primary depletion of a core. This is a part of a more comprehensive study of obtaining criteria for determining when to initiate a pressure maintenance program and what fluids to in-ject. EQUIPMENT A schematic diagram of the apparatus is shown in Fig. 1. Fluid transfer was accomplished with metering pumps. Pressure control was ob-

Jan 1, 1957

By E. S. Bardwell

TWENTY years ago, W. T. Burns, in his paper presented at the Butte Meeting of the Institute, discussed the general scheme then in use in the electrolytic copper refinery of the Anaconda Copper Mining. Co. at Great Falls, Mont., for removing impurities from tank-room electrolyte and controlling its acid content. Since then marked changes have taken place in copper-refinery practice at Great Falls. The electrolytic copper refinery in use in 1913 has been replaced by a new and entirely modern plant capable of producing up to 27,000,000 lb. of cathode copper per month. With the building of the new plant in 1916, the treatment of converter anodes was discontinued. At first the substitution of refined anodes for converter anodes resulted in a decrease in the impurity content of the anodes, but as time went on, changes in metallurgical practices at the smelter resulted in substantial increases in the impurity content of the anodes. The leaching of the silver slime to remove copper before shipment to Raritan for treatment further added to the purification problem. The fact that the scheme of purifying electrolyte which Mr. Burns described in his paper' has proved adequate for our needs under a wide variation of conditions speaks well for its essential soundness.

Jan 1, 1933

By Irving Cadoff, Kurt Komarek, Edward Miller

THE lead-telluride phase diagram as compiled by ansen' has one intermetallic compound, PbTe, with solid-solubility limits extending from 22 to 45 wt pct Te (31.4 to 57.1 at. pct). Pelzel2 redetermined the solubility limits on the lead-rich side of the compound by measuring the relative areas of the two phases in samples annealed in the liquid + compound region, and obtained data that agreed with that of Hansen. Recent studies of the semiconducting properties of PbTe3 however, have indicated that addition of either lead or tellurium to PbTe does not produce samples having carrier concentrations greater than about 10 19 cm-3. Assuming that each impurity atom results in one ionized charge carrier, this carrier concentration corresponds to a solubility range of less than 0.04 at. pct. Fritts and Karrar4 have also observed two phases in samples containing from 0.15 to 3.0 pct excess Pb. To resolve the discrepancy between these data, the solid solubility limits of the compound PbTe were reinvestigated, using several other techniques. Ten 25-g samples with compositions of 1/2, 1, 3, 5, and 10 wt pct excess Pb and Te and two 100-g samples of 15 and 65 wt pct Te were prepared, sealed in evacuated quartz capsules, and melted at 950oC. The 1 pct excess Pb and Te and the 15 and 65 wt pct Te alloys were homogenized for 96 hr at 450°C; the remaining specimens were annealed 50°C below the solidus temperature reported in Hansen. The specimens were polished and etched with dilute HNO,. All the samples were two phase, the second phase appearing at grain boundaries or as spheroidized inclusions in the grains. In the case of the tellurium rich specimens, the second phase could be identified as a eutectic. Debye-Scherrer powder diffraction patterns of the i, 1, 3, 5, and 10 pct excess samples were obtained using CuKa filtered radiation. The films were indexed as the B1 or NaCl structure. The calculated lattice parameter of PbTe was the same for all the specimens, with an average of a0 = 6.460 ± 0.0005A. Lines due to excess lead or tellurium were very faint but could be clearly seen in all the films. The relative areas of the two phases in the 15 and 65 wt pct Te samples were corrected for the differences in density of Pb, Te, and PbTe, and taken as proportional to the relative volumes of the two phases. The corrected relative volumes agreed with a phase diagram having negligible solubility of both lead and tellurium in lead tellurium. The density of the two specimens was obtained to give a third independent determination of the phase limits. The specimens were broken into small pieces to eliminate any internal porosity, and adherent air bubbles were removed by vigorous shaking under water for several hours. The density of lead (11.34 g per cm3) and of tellurium (6.25 g per cm3) was taken from the International Critical Tables and that of stoichiometric PbTe (8.25 g per cm3) calculated from the lattice parameter. For the 15 wt pct Te samples, the density assuming no solubility was calculated to be 9.89 g per cm3; the observed density was 9.86 g per cm8. For the 65 wt pct Te alloy, the density calculated for the case of no solubility was 7.24 g per cm3; the measured density wag 7.22 g per cm3. These results are consistent with those of planimetry and X-ray. SUMMARY Data have been presented which show that the solid solubility of both lead and tellurium in PbTe is

Jan 1, 1961

By F. L. Toy, C. E. Sims

I. A. Sirel—I would like to ask Mr. Sims what would the preferred hot metal analysis be as far as manganese and silicon are concerned if you used specially made iron for this process instead of basic iron. C. E. Sims (authors' reply)—A preferred composition would contain somewhat less silicon than the basic pig iron used in these experiments. High silicon requires a large lime addition. Lime must be added in sufficient quantity to neutralize the silica formed and to leave an excess for dephosphorization. Manganese presents almost no problem in operation. It is almost completely oxidized and, in burning, develops considerable heat. The evidence indicates, however, that, in continuous commercial operation, there will be an excess of heat produced, and the bath will need to be cooled in some manner as by the addition of scrap or by utilizing the energy for the direct reduction of ore. There do not seem to be any serious limitations on composition of pig iron. One heat was made with an iron containing 2.27 pct silicon and the phosphorus finished at 0.007 pct. In another, the iron contained 0.45 pct phosphorus which was lowered to 0.019 pct. This indicates considerable leeway in composition. D. R. Loughrey—We are all very much interested in the recent discovery of very large deposits of iron ore both in Labrador and in Venezuela. I would like to ask Mr. Sims if the iron ore at either or both of these places is such that it would lend itself to the manufacture of iron suitable for use in the turbohearth. C. E. Sims-—According to my information, those ores are not essentially different from ores now used in this country for making basic pig. They should, therefore, be adaptable to this process. D. I. Brown—You have spoken about the leeway, or spread in analysis of the various irons you can use in the vessel. I would like to have you tell us, if you can, about the different kinds of steels which can be made in such a vessel. The turbohearth process, or it might more aptly be called pneumatic openhearth, is a little different from that used in most Bessemer shops and in the one in which I worked. If we had a blow in the air over 10 min, the boss was in the pulpit in a hurry

Jan 1, 1951

By R. F. Pilgrim

A digital computer program to mathematically simulate the effect of limited changes in feed rate in the range of 80 to 95 tph on a plant-scale wet grinding circuit has been developed and tested. The circuit studied included an 8-ft-diam X 12-ft rod mill operating in open circuit and feeding two parallel 12-ft-diam x 10-ft pebble mills, each one operating in closed circuit with an 8 X 32-ft rake classifier. The simulation is an empirical one based on two sets of data collected manually from the operating circuit under what was said to be steady-state feed rates of 80 and 95 tph with all other operating variables also at steady state. The procedure is a combination of several published approaches to the modeling of grinding mills and classifiers and it is applicable to a wide range of circuits. The program permits the computing of the size distributions of all feeds and discharges of all grinding units and classifiers in the circuit for a specified feed rate. The data used in this report for demonstrating the program are unsatisfactory since the circuit was not operating under steady-state conditions when it was sampled. Consequently the circuit model parameters could not be accurately estimated. The predictive power would be greatly improved if new data were obtained under true steady-state conditions.

Jan 1, 1973

By R. B. Ladoo, C. A. Stokes, R. N. Secord, A. L. Hall

INDUSTRIAL mineral history shows that the entrance of new, nonmetallic minerals into commercial production can be expected to occur from time to time. Latest entrant into the field is wollastonite. Except for one short-lived period in Kern County, Calif., starting in 1933, wollastonite has never before been produced on a commercial scale. But the signs are up for its entrance as an economic factor in the mineral market. Small scale experimental production from a deposit near Willsboro, N. Y., started about 1943. A pilot plant was built in 1949-50 and irregular, small scale, production has continued. In early 1951 Godfrey L. Cabot, Inc. of Boston, world's largest producer of carbon black, took an operational lease on the property to study the deposits and make market surveys. This became Cabot's first venture in the mineral field, when they took over operations and began design of a new mill, expected in production in 1953. Properties The properties and major uses of wollastonite are comparable to New York fibrous talc. It has about the same specific gravity and index of refraction as talc, but is somewhat whiter and softer. The two most important fields of use, paint and ceramics, are the same as for talc. Ground wollastonite has a fiber length as much as 13 to 15 times the diameter. This particular property makes it applicable in the paint field and others. In addition, the length-diameter ratio may be controlled to rather narrow limits by choice of grinding method. Another important commercial property is brightness or whiteness. Wollastonite reads from 92 to 96 pct of MgO on the G.E. brightness meter for a 99 pct -325 mesh grind. Purity and uniformity of product are important. Chemically, the wollastonite now being mined analyzes SiO2 51.76, CaO 47.56, FeO 0.46, MnO 0.04, and H2O 0.09 pct. Theoretically pure wollastonite analyzes SiO2 51.75 and CaO 48.25 pct. This analysis indicates over 98 pct calcium silicate, with only small amounts of contaminating ingredients. That these ingredients are not detrimental to color or brightness is shown by the high brightness value of the fine ground material. [ ] By-product calcium silicate from electric furnace production of phosphoric acid has little physical re-semblance. to this wollastonite, being an off color white, and lacking in fibrous crystalline character. Minerology Wollastonite is a calcium metasilicate, CaSiO3, a white, medium hard, fibrous mineral. In this deposit wollastonite occurs as well crystallized aggregates of bladed crystals intergrown with garnet, and with a few percent of green diopside. The beneficiated product is about 75 pct wollastonite, 15 pct garnet, and 10 pct waste, largely middling. Wollastonite-garnet ore occurs in at least two beds. The main bed, varying in true thickness from 30 to 70 ft, dips into the hill at an average 30° and is enclosed in gneisses. Diamond drilling has proven the orebody to an average depth of 200 ft along 2000 ft of outcrop with adequate tonnage for many years of quarry operation. The wollastonite-garnet ratio varies locally, but average composition is uniform over long distances. A friable ore, it is easy to drill, shoot, and crush. Beneficiation Unlike talc this ore has to be beneficiated. Successful treatment depends upon the fact that it contains virtually nothing but wollastonite, garnet and a minor percentage of diopside. A very pure wollastonite product can be made by high intensity magnetic and/or gravity separation methods.

Jan 1, 1952