Search Documents

By A. G. Pasamehmetoglu

This paper describes the conver¬gence and load measurements carried out in inclined seams at five longwall faces, two of which were supported by hydraulic props and the other three by conventional timber supports in Karadon-Gelik mine. The minimum support capacities determined in this study are compared with the results obtained from two empirical approaches suggested by Wilson (1975) and Jacobi (1981). The characteristics of hydraulic props to be used and support patterns in the longwalls are found, conclu¬sions are drawn and suggestions are made. Design nomograms are prepared for field engineers, in order to be able to approach the problem more confidently and realistically.

Jan 1, 1992

By P. Bermingham

A new approach to load testing of high capacity piles is presented. The method is mobile, inexpensive, repeatable and non-destructive allowing for multiple pile testing at a single site. A reaction mass is placed over a pressure chamber situated atop the pile to be tested. The test method is significant in that it can produce linearly increasing forces of high magnitude (over 5.0 MN) with durations of up to 80 milliseconds. This represents pulse durations an order of magnitude longer than achieved using a drop hammer. The accelerations the pile undergoes are less than one g, (conventional dynamic methods = 50 to 100 g). These effects combine to produce pile behaviour no longer dominated by the action of stress wave, instead the pile is under high levels of stress through its length during the force input. This is representative of the situation when static loads are applied, thus the method may be considered quasi-static. Further advances introduced with this method are that pile deflection and transmitted force are measured directly by means of a laser beam and load cell. This allows accurate correlation of event load displacement histories without the error associated with zero shift (acceleration integration) or non-homogeneous materials (strain measurement). The load displacement histories emulate those obtained for static load testing.

Jan 1, 1989

By S Arai

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Podiform chromitites are commonly found in the Moho transition zone to the mantle section of ophiolites, but have been very rarely found from the current ocean floor, even though some ophiolites are considered as a slice of oceanic lithosphere. One of the factors controlling podiform chromitite formation is the chemistry of host mantle peridotite; an intermediately refractory harzburgite is the optimum host for chromitites. This harzburgite represents the most common lithology of the oceanic lithosphere, where the peridotite-melt reaction, which is another condition, is possibly common there. The oceanic lithosphere mantle is thus a good host for podiform chromitites. The apparent rarity of documented oceanic chromitites is solely due to under-sampling of mantle materials from the fast-spreading ridge and the segment centre of slow-spreading ridges. Some ophiolitic chromitites formed not from genuine mid-ocean-ridge basalt (MORB) but from wet MORB due to the situation of typical ophiolites, which formed not at ordinary mid-ocean ridges but at supra-subduction zone spreading centres.CITATION:Arai, S, 2015. Podiform chromitites do form beneath mid-ocean ridges , in Proceedings PACRIM 2015 Congress, pp 465–468 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By C. Larsen, D. Fragomeni, A. Vien, D. G. Fisher

"MOCCA is a Multivariable Optimal Constrained Control Algorithm developed specifically for non-square industrial control applications with practical difficulties such as interactions, time delays, constraints, modelling errors, etc. MOCCA consists of an off-line simulation/translation module, for tuning the control parameters, and an on-line module that implements the designed control law.This paper describes an evaluation of MOCCA on the Hemlo grinding circuit which comprises one open circuit ball mill and two closed circuit ball mills in series. In this case a 4x4 unconstrained control problem was considered. The manipulated variables included the fresh ore feed rate and three pump box water additions. The controlled variables were the grinding circuit product particle size and three pump box levels. In this application soft constraints were implemented through control action and control error weighting. The feedforward capability of MOCCA was used to compensate for a measured water flow disturbance to one of the pump boxes. MOCCA performed very well during plant evaluations when compared to the original classical multi-loop control strategy and proved to be quite robust. Perhaps most importantly, the process engineers and plant operators have a high level of comfort both in understanding MOCCA's general operating principles, and with its demonstrated performance."

Jan 1, 1991

Predicting Flotation Response from Liberation Information

Sep 13, 2010

By Bjarne Ekberg

"The most economical way of dewatering mineral concentrates is to reduce the moisture content in the material mechanically using thickeners and filtration avoiding thermal drying whenever possible. In addition to this, the dewatering process should produce low moisture cake, high quality liquid, consume little energy. As a part of the dewatering process The CERAMEC® capillary filter has been proven to meet these requirements in over 150 installations. The filtration is done by using ceramic filter plates with small pore size. The capillary action in the filter medium secures gas free filtration at good vacuum, and due to the small pore size, filtrate is crystal clean and particle free. The energy consumption is minimal. This paper will discuss results from filters installed at Pyhäsalmi Mine Oy in Finland where the technology was has been used since the late eighties. Results from more recent installations like Los Pelambres in Chile and LKAB in Sweden will also be discussed.INTRODUCTIONThe idea of using capillary action to make dewatering more efficient was invented two decades ago. Ten years later whole filter plants utilizing the new method were delivered to mine concentrators for dewatering of mineral concentrates. Further development of ceramic membrane plates made it possible to meet the requirements in iron ore dewatering. In addition to low cake moisture, high capacity and low energy consumption, there are a lot of environmental advantages in using capillary filtration. One of them is clear filtrate.CAPILLARY FILTRATIONA micro-porous filter material behaves like a large number of narrow capillaries forming a network. When a pressure difference ?P is applied over the wetted, hydrophilic pore with the radius r, the force striving to push the water out of the pore will be ?Ppr2. The force striving to hold the water in the pore will be the vector force 2pr? cosa of the surface tension ? and the cosine contact angle a. Equalling those forces and solving the equation for ?P we get"

Jan 1, 2003

By Mohammad Irshad, Klaus Mussger, Harald Wagner

Despite the fact that the New Austrian Tunneling Method; NATM, has been used in the United States for the past 23 years or so, still considerable misconceptions exist in the industry about the nature of the method and its implementation. In the authors’ view its implications are usually not well understood. The paper provides an overview of the highlights of NATM usage over the past two decades to illustrate the point that NATM is now a well-established tunneling method in the U.S.A. Accordingly the thrust of this paper is on the more pragmatic aspects of the NATM technology usage as it concerns the Owners, Designers and the Contractors. Prior to examining the implications of NATM usage from the viewpoints of various stakeholders, it should be helpful to first briefly provide an overview of the history of the method as it was introduced and implemented on several key tunneling projects in the US, over the last 2 plus decades.

Jan 1, 2005

By Trevor Yeomans

"NVI Mining’s Myra Falls Operation is a forty year old underground mining operation feeding a 4000 mtpd concentrator.The current Mill, built in 1985, was designed to process a large massive sulphide ore-body. This ore-body, known as the “HW”, contains about 50% pyrite. Value minerals are chalcopyrite, and sphalerite, with precious metals occurring in all mineral types.By 1997, mining of a new ore-body, known as “Battle-Gap” commenced. Mineralogically complex, the new orebody contains about 15% pyrite, copper minerals including primary chalcopyrite, secondary bornite, chalcocite and tennantite, combined with increased galena and sphalerite.Flotation performance generally decreased with increasing amounts of Battle-Gap ore types, with both copper concentrate quality (increased lead and zinc content) and copper recoveries being affected.Following significant metallurgical testwork, a new fully sequential copper-lead-zinc flotation flowsheet and reagent scheme was developed.This sequential flowsheet was progressively installed and commissioned during 2006.Copper concentrate lead and zinc smelter penalty contents have been reduced by some 40%, whilst increasing copper recovery by 10%.INTRODUCTIONNVI Mining operates the Myra Falls Operation near Campbell River on Vancouver Island, BC. The complex has been in operation since 1966 with mining being predominantly underground. One unique feature of Myra Falls is that the mine operates within a BC Provincial Park.In 1985, a new large massive sulphide ore-body (HW) had been defined, and metallurgically tested. A new concentrator was built based upon this massive pyrite, chalcopyrite, and sphalerite mineralization producing copper and zinc concentrates by conventional flotation methods."

Jan 1, 2008

By J. Griesel, P. H. F. Bouwer, K. Bisaka

Transalloys produces 160 000 tons of SiMn per annum from five AC submerged-arc furnaces. The lime-ore melt from two AC open-arc furnaces is contacted with SiMn to produce 50 000 tons of medium carbon FeMn per annum. Metallics in the slag are reclaimed in a jigging plant, which has been in operation since 1999. The flow of materials between the jigging plant and furnaces has been optimised. The amount of recycle slag in the feed of the SiMn furnaces has been decreased by more than 30% which still provides satisfactory stability of the furnace operation. The jigging plant has absorbed all the additional slag generated, to recover SiMn metal. A review of the raw materials used and operating parameters for SiMn production was also undertaken. Slag to metal ratios were decreased by more than 30% by reducing the slag recycle, removing magnesite from the recipe and introducing high-grade ore. Electrode penetration was improved by reducing coke levels and by utilising more reactive coal. The pitch circle diameter (PCD) was reduced to get a better operating stability on furnace no 5 using the MINSTRAL Control System. Energy consumption on the furnaces improved by more than 15% while SiMn production increased as a result by more than 18%.

Jan 1, 2004

By Phil Shelton

What exactly does clean coal mean? Mining coal creates dust and releases methane gas. And burning coal liberates CO2 and emits particulates, including SO2 and NOx. Coal creates wastes that are often stored in unsightly and potentially dangerous slag heaps and lagoons. When clean coal technology is discussed, it sometimes seems that creating modern or ?ultra super critical? coal-fired power stations is presented as the main or even the only answer. However, there may be a more holistic approach. Using the energy potential of coal is always going to have environmental impacts. Some of these will be negative. But the need to secure future energy resources demands that society tackle these negative issues and find ways to minimize and offset them.

Jan 1, 2010

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1963. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III of the Minerals Yearbook. COAL Injury experience of the coal-mining industry was improved slightly in 1963, as measured by the 2-percent decline in the Injury-frequency rate. Although the total number of fatal and nonfatal injuries increased 1 percent, the greater proportional increase of 3 percent in man-hours worked accounted for the improved frequency rate. Employment and injury data for 1963 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1964

By Pierre Boileau

Outline ? Who are We? ? Canada?s GHG Emissions 1990 - 2000 ? Emissions from the Petroleum Sector ? Emissions from Petroleum Exports ? Emissions from Manufacturing Industries ? Emissions from Mining and Metallurgy ? Conclusions Greenhouse Gas Division Key Functions: ? National GHG Inventory Report, Emission & Removal Trends Analysis, and Indicator Fact Sheets ? Scientific and Engineering Guidance, Technical Advice, Data Quality Assurance & Quality Control and Methodological/Data Development ? International Negotiations (FCCC) & scientific/technical guidelines (IPCC & ISO) ? Expert Review Teams (ERTs) ? Outreach ? GHG Verification Centre ? Clearinghouse ? Protocol Development

Nov 1, 2002

By F. Calizaya

The PT Freeport Indonesia‘s Deep Ore Zone(DOZ) copper deposit is located in the province of Irian-Jaya, Indonesia. Currently, a block cave mine is being developed around this deposit. Production is scheduled to start in year 2000 and to ramp up to25,000 tpd by year 2003. The air quantity requirement for this mine is equal to 780 m3/s. To supply this quantity, the mine will require five centrifugal fans (one 450 and four 750 kW fans). This study summarizes the technical aspects related to the installation and commissioning of one of these fans. The fan was installed on the surface in a parallel arrangement with two others. It has a design capacity of 240 m3/s of air at 2.2 kPa of static pressure. The study presents the installation details from the underground shaft excavation and portal development through fan testing and commissioning. It also presents the results of a monitoring system that was installed to determine the fan duties.

Jan 1, 2000

By Fathi Abdrabbo

Open caissons are used for many geotechnical engineering applications. Open caissons may be used as deep foundation elements bypassing weak soils to tip in firm deeper strata, and in rivers and maritime construction to reduce the risk of scour. Open caissons are also used for collecting sewage water through gravity sewer pipe networks or from sewer force mains. In such applications, the design and construction of open caissons require a detailed soil investigation program. In this way, the design and construction plan of an open caisson can be developed with full knowledge of the prevailing subsoil conditions. The engineering and construction techniques are key factors to achieve functional caissons. Based on close observations during construction stages, the current study presents some challenges that were encountered during the construction of two open caissons of internal diameters 20 m and 10 m (65.6 ft and 32.8 ft). This paper describes the procedure followed to alleviate the construction difficulties encountered. Site exploration program and control measures required to satisfy design and construction requirements are crucial aspects. Sinking of open caissons in dense or very dense sands is risky. Incorrect sinking of open caissons may cause extra cost, delay in construction, and harm to nearby structures. Air/water jetting near the cutting edge of an open caisson, outside slurry trench, and/or inside open trench may be used to drive an open caisson downward. Unsymmetrical work around an open caisson may lead to tilting of the caisson. If this occurs, the tilt should be immediately corrected before resuming the sinking process. Improper cleaning of fine materials on the caisson?s excavation bed, and/or inappropriate pouring of underwater concrete may result in a defective concrete seal. The paper contains a series of practical guidelines to assist those intending to use open caissons, and shares good caisson sinking practice with practitioners. Finally, the study aims to understand the difficulties encountered and to anticipate future problems.

Jan 1, 2012

By S. B. Johnson

Keywords: Spray, Aluminum, Simulation A stochastic, droplet-resolved model has been developed to describe the behavior of a binary aluminum alloy spray during the spray-rolling process. In this process, a molten aluminum alloy is atomized and the resulting spray is deposited on the rolls of a twin-roll caster to produce aluminum strip. The one-way coupled spray model allows the prediction of spray characteristics such as enthalpy and solid fraction, and their distribution between the nozzle and the deposition surface. This paper outlines the model development and compares the predicted spray dynamics to PDI measurements performed in a controlled configuration. Predicted and measured droplet velocity and size distributions are presented for two points along the spray centerline along with predicted spray averaged specific enthalpy and solid fraction curves.

Jan 1, 2005

High Pressure Sulfuric Acid/Oxygen Leaching of Platinum Group Metals Bearing Ni-Cu Mattes The processing of platinum bearing Ni-Cu ores for the extraction of platinum group metals (PGMs) involves comminution, flotation, smelting, and converter treatment of the furnace matte. Leaching circuits are predominantly used for further processing to separate the base metals and PGMs contained in the converter matte. Nickel dissolution is primarily achieved in the first stage leach (high pressure or atmospheric leaching, or a combination of the two), which is followed by second stage high pressure sulphuric acid/oxygen leaching to dissolve copper and the remaining nickel. PGMs are recovered from the leaching residue in downstream processes, and their dissolution in the first two leaching stages must hence be limited. Studies have been conducted to investigate the leaching mechanisms and kinetics of base metals in different leaching environments. The key operating parameters that influence the leaching kinetics of these metals include the temperature, acid concentration, degree of agitation, feed particle size distribution, and oxygen partial pressure. There is, however, a limited understanding of the behaviour of PGMs in the high pressure leaching process. Consequently, this process is controlled based on operators' intuition despite its importance in the recovery of PGMs. An improved fundamental understanding of the behaviour of PGMs in this leaching environment is required to be able to accurately model the process. This in turn will allow the development of an improved control strategy and the estimation of optimum operating conditions. An overview of the leaching mechanisms of base metals and the effects of key operating parameters on their dissolution kinetics in different leaching environments are presented. Models that have been developed to predict the leaching behaviour of base metals are discussed and evaluated. Finally, initial results obtained with an experimental setup that will be used to investigate the behaviour of PGMs in high pressure leaching systems are discussed and compared with published results.

Sep 13, 2010

By R. O. Burt

"Gravity Concentration, the oldest form of Mineral Processing, remains of major importance to the Industry. Current applications of Gravity Concentration are briefly examined.The Paper details one approach to the development of a Gravity Concentration Plant, from laboratory and mineralogical techniques, through Pilot Plant testing, where applicable, to the actual design of the plant.INTRODUCTIONGravity Concentration, once the major method of concentrating minerals has, for much of the twentieth century been regarded, like the dodo bird, as obsolete. However, in more recent years it is enjoying something of a renaissance, and is once again being treated as a useful, economic alternative in the Mineral Processing Engineers' arsenal.An indication of the broad application of gravity concentration is the variety of minerals presently recovered. A list is given in Table 1; this list is not exhaustive."

Jan 1, 1984

By John Ward Smith

Dawsonite-bearing oil shale of Colorado's Green River formation offers a unique and vast (more than 5.9 Gt of A120 j) resource of easily extractable alumina. The processing methods required by the thermal reactions of dawsonite and its oil-shale carrier also require production of shale oil, soda ash, and nahcolite as marketable coproducts. These production methods are presented. The alumina production process is contrasted with the Bayer process to describe technical advantages of extraction of alumina from oil shale which may offset the problems associated with processing a relatively lean ore. While alumina production from oil shale requires development of new technology, the technical problems appear solvable. Only the political problems arising from the now onerous and completely unnecessary federal oil-shale withdrawal appear less solvable.

Jan 1, 1982

By Jean-Claude LeRoy, Herman Keller

"INTRODUCTIONEROCON's work is the reclamation of mine wastelands. It has had considerable experience in particular in the reclamation of gold mine tailings in the Canadian Shield since the latter part of the sixties when most gold mines were closing down.A typical example is the famous Hollinger Mine in Timmins which produced $566 million worth of metal from 1910 to 1968 and had left behind some 56 million tons of tailings covering about 1,000 acres which were reclaimed on very short order and are now lush meadows of agricultural quality.To date, practically all gold mine tailings have been reclaimed once and for all by establishing a permanent, self-sustaining and maintenance free vegetation cover.RECLAMATION & THE MINING TOWNSThe first appreciation of people in a mining community where the tailings have been revegetated will be noticing one day the elimination of dusty conditions that used to arise formerly on every dry and windy day. In that respect, EROCON encourages not only vegetating the tailings but also the immediate surroundings of the mills and plants themselves at active mines. The elimination of windborne dust will result in an appreciable decrease in maintenance costs of plant and machinery and more pleasant working conditions for all."

Jan 1, 1975

By M. Massinaei, S. Abasi, M. Oliazadeh

Reliable measurement and control of the pulp-froth interface (froth depth) in the flotation columns is critical to achieve the desired metallurgical performance. Shallow froths result in a reduction of grade because of particle entrainment and deep froths reduce recovery because of the drop back of entrained and weak hydrophobic particles to the pulp zone. The cleaner circuit at Miduk copper concentrator consists of three parallel MicrocelTM flotation columns 4 m in diameter and 12 m in height. The interface level of the flotation columns is measured by two pressure sensors located at 1.4 and 2.4 m from the cell lip (in the collection zone). In this study the performance of the level detection system at different operating conditions was evaluated. A calibrated float-ultrasonic location system was used for measuring the actual froth depth. The results indicated that the existing level control system was subject to considerable error. The absolute error was found to be 33.27 cm. This was mainly attributed to the constant set-point value assigned to the froth density (ρf=0.3 g/cm3), which actually varies with the operating conditions. The actual froth density at different conditions was calculated and its average value (ρf=0.12 g/cm3) was re-set in the control system. This resulted in substantial reduction in the level-detecting error. Recommendations for more accurate measurement of the interface level were presented. INTRODUCTION Froth flotation is a complicated process because of many involved variables. One of the most significant controlled variables in the flotation process is the pulp-froth interface (froth depth). The froth depth has a profound influence on the metallurgical performance parameters (i.e. grade and recovery). Shallow froths result in grade reduction because of particle entrainment and deep froths reduce recovery resulted from the drop back of entrained and weak hydrophobic particles to the pulp zone (Finch and Dobby, 1990). Various techniques have been developed for measuring the interface level of the flotation cells in the last few decades. These techniques can be classified as: Techniques based on hydrostatic pressure measurements (Finch & Dobby, 1990), Techniques based on the density gradient (float) (Moys & Finch, 1988), Techniques based on conductivity measurements (Uribe-Salas, 1991), Techniques based on temperature measurements (Moys & Finch, 1989).

Jan 1, 2019