Search Documents

By W. H. Bassett

In considering the effects of reducing gases on hot solid copper the following conclusions have been reached. (1) Depth of deoxidation of copper heated in reducing gas is greater the smaller the amount of cuprous oxide originally present in the copper, the range studied being from 0.015 to 0.136 per cent. oxygen. It is suggested that the reason for this difference in depth of deoxidation is that, when the copper is low in cuprous oxide, the reducing gas is diluted less by the gas that is formed in the reaction than when the copper is high in cuprous oxide; and the greater the concentration of the reducing gas the deeper the deoxidation. (2) The rate of deoxidation is much mire rapid at the beginning of exposure than at the end, a condition especially noticeable at temperatures around 900° C.; that is, deoxidation is retarded as the depth penetrated by the reducing gas increases. (3) Within the accuracy of the experiments arsenic in copper up to 0.5 per cent. has no tendency to increase or decrease the action of a reducing gas on the cuprous oxide present in the copper. IN 1912 pieces of 0.365-in. hard copper rod 1/2 in. long were heated in a porcelain tube in an electric furnace, while illuminating gas was passed through. An approximate analysis of this gas is: FIG. 1.-EFFECT OF TIME AND TEMPERATURE ON DEOXIDATION RATE OF 0.365-IN. COPPER BY ILLUMINATING GAS; COPPER PLUS SILVER, 99.983 PER CENT. Hydrogen 38 per cent., carbon monoxide 30 per cent., illuminants 13 per cent., methane 10 per cent., ethane 3 per cent., carbon dioxide 3 per cent., nitrogen 2 per cent., oxygen 0.4 per cent. After heating for various lengths of time at various temperatures, samples were quenched

Jan 1, 1926

By E. P. Abrahamson II

The effect of transition elements which form binary solid solution upon the recrystallization temperature of zirconium has been investigated. All additions raised the recrystallization temperature. A correlation is obtained between the logarithm of the rate of change of recrystallization temperature with atomic percent solute and the free atom ground state electron configuration of the solute element. ThE work of Abrahamson, et al., on dilute binary solid-solution alloys indicated a correlation between the free-atom ground state electron configuration of the solute and either the brittle-ductile transition or recrystallization temperature. These studies were carried out on bcc base materials. The implication is that the outer s and d electrons of the solute are the prime determinant of the absolute rate of change of recrystallization or transition temperature. Furthermore, the limit of linearity has been shown to be a function of solute electron configuration for recrystallization in iron and vanadium. To date no Complete systematic recrystallization study of dilute binary zirconium base alloys has been made. It is the purpose of this study to note whether the change in solvent structure from bcc to hcp will influence the correlation. It was also desired to learn more of the role of the electron configuration of the solvent on recrystallization temperature. PROCEDURE All alloys were made using 99.87 pct Zr with 0.01 Cr, 0.04 Fe, 0.006 Hf, 0.003 Mg, 0.003 Mn, 0.003 N, and 0.080 0 (132 BHN). The solute elements were 99.9 pct pure. According to the published binary phase diagrams6 and metallographic examinations at X750, all alloys used were solid solutions. The alloys were arc melted and remelted six times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot pressed at 950°C to 0.450 in., upset pressed to 0.350 in., and annealed at 800°C for 1 hr. The specimens were then Blanchard ground to 0.250 in., removing 0.050 in. from each side. The grain size of the material at this stage was found to be 8000 100 grains per sq mm. The specimens were then cold rolled to 0.130 in. and cold pressed to 0.125 in., yielding 50 1 pct cold work. All alloys were then chemically analyzed for the principal addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The rolled sheet was cut into 6.75 by 0.25-in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was 250o to 900°C over the 6-in. length, recorded continuously by six thermocouples resting on each specimen. Control was 3oC, accomplished at the hot end. The recrystallization temperature was determined metallographically using polarized light. The criterion chosen was the point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be 3°C. RESULTS Three different pure zirconium specimens were tested, and the recrystallization temperature was

Jan 1, 1962

By Lloyd G. Fitzgerald

"The dangerous nature of explosives makes them a potential hazard wherever they are used, but they are likely to exercise their greatest harmfulness under conditions inherent in coal mining. The ease with which explosives can be detonated and the suddenness and violence with which they detonate require great care in their handling and use, if acci-dents are to be avoided. Campaigns have been waged by the manufacturers, the Federal Bureau of Mines, coal-mining companies, and other agencies to educate users of explosives in their dangers and in their proper use and care.Probably 95 percent of the explosives accidents can be attributed to poor judgment, carelessness, negligence, or chance taking. In many explosives accidents it is difficult to determine the cause definitely, as the evidence of the origin is destroyed by the blast and frequently those involved have been killed. Survivors of the accident often are of little help in determining the cause, as the accident occurs so suddenly they cannot tell what happened or prefer not to divulge the information they have because it may point to their own carelessness.A survey has indicated that about 10 percent of all fatalities in coal mines were caused by explosives accidents (excluding gas and dust explosions initiated by explosives). A list of explosives accidents by States, from 1925 to 1932, classified according to the severity of the accidents, indicated that Kentucky and Wyoming had the greatest number of fatalities resulting from explosives accidents. Records of the Bureau of Mines show that 14 coal-mine explosions occurred from January 1 to June 1, 1943. Explosives were involved in four of these explosions. Black powder caused two of the accidents and permissible explosives used in a nonpermissible manner the other two. These statistics are mentioned to show that explosives are still causing severe accidents.Elimination of the hazards associated with explosives begins on the surface. Storage magazines should have no opening, except for entrance and ventilation; ventilators should be screened effectively to prevent the admittance of sparks as well as to prevent unauthorized entrance. The interior should be kept clean and dry, and the floor should be of nonsparking material with no metal exposed. The surrounding area should be kept free of combustible material for not less than 25 feet (and preferably 50 feet) in all directions. Storage magazines should be fire-resistant and reasonably bulletproof."

Aug 1, 1944

By M. B. Boyer, C. H. Herty, F. A. Hartgen, G. L. Frear

"DEFINITION OF VISCOSITYViscosity has been defined as the resistance experienced by one portion of a liquid moving over another portion, such as one molecular plane moving over an adjacent plane. A measure of viscosity is the force required to keep one plane in motion at Unit velocity, the other plane being considered stationary. Figure 1 illustrates the general idea that the surface friction between two adjacent areas will be greater the larger the molecules. Therefore it may be assumed that viscosity will be increased by molecular association or agglomeration, and likewise dissociation rill decrease viscosity. According to Maxwell (1)6 the unit of viscosity, the poise, is the tangential force per square centimeter of area of either of two horizontal planes 1 centimeter apart, one of which is fixed while the other moves with unit velocity, the space between being filled with viscous liquid of unit viscosity.The need for a satisfactory apparatus and experimental procedure for the determination of viscosity of high-melting materials at temperatures corresponding to those in pig-iron and steel making has been recognized during the past few decades. The condition of the slag during the smelting and refining periods in the iron- and steel-making processes exerts an important influence on the metal product obtained, this slag condition really meaning the state of viscosity or, vice versa, fluidity, which the slag attains under certain conditions."

Jun 1, 1934

The Mineral Density Separator (MDS) was developed by Mintek to predict mineral separation in a plant, evaluate efficiencies and develop scale-up parameters. This study investigated the influence of particle size on the results of the MDS, the misplacement of material in the MDS and the possibility of replacing heavy liquid float and sink analyses of coal with MDS analyses. Six tests were done with coal of different size ranges. Each MDS layer was subjected to a float-sink analysis whereafter each float fraction was screened to determine the particle size distribution. The results indicated that MDS results represent float-sink analyses when compared to an ash curve. There is some misplacement in the different MDS layers, but this does not seem to influence the results negatively. Keywords Mineral density separator, sink-float analyses, heavy liquid analyses, washability curve

Jan 1, 2006

By D. Harrington

The record of fatalities from mine explosions during the past 2 fiscal years has been anything but encouraging; more men were killed by explosions (379) than were killed from the ante cause during to' preceding 6 years combined (368). The reason for the large increase in the number of explosion fatalities during the past 2 years as compared with the previous 6 years is not entirely clear. In some instances, there has been laxity in the enforcement of State mining laws; in others, both workers and operating officials is have failed to observe recognized precautionary measures to prevent explosions. In many of the explosions that lave occurred within the asst few years in mechanized mines it has been evident that speed of operation and a demand for maximum tonnage at minimum cost resulted in neglect of ordinary safety measures.

Jan 1, 1942

By L. W. Burger

The need to establish and harmonise methodologies to quantify air emissions, atmospheric dispersion and the consequences of air pollutants (especially hexavalent chromium) from the ferrochrome industry became important aspects with the increasing demands for comprehensive impact assessments. The paper includes a synthesis of current knowledge on the following aspects: ? Locally and internationally accepted methodologies for the quantification of chromium emissions, including sampling methods and emission factors; ? A compilation of recognised and accepted air quality sampling and laboratory analysing techniques; and, ? Dispersion modelling and impact assessment tools. Depositing and removing materials from the chromium ore stockpile and wind erosion of exposed stockpiles result in mainly chromite emissions unlikely to contain significant amounts of hexavalent chromium. Pre-treatment processes such as drying, crushing and screening also produces chromium emissions, but mainly as trivalent chromium. The smelting of chromium is the major source of chromium emissions - open furnaces have the highest uncontrolled chromium emissions, followed by semi-closed and closed furnaces, respectively. Based on the current knowledge on emission rates, interim emission factors for particulate, total chromium and hexavalent chromium releases are provided. Ambient sampling and analytical methods to determine environmental exposure of the general public require that hexavalent chromium needs to be quantified in very low concentrations. Suggested sampling and analytical methods for both source characterisation and ambient monitoring are provided. The selection between dispersion models needs to be based on the size of the modelling domain and the complexity of the terrain. The discussion on dispersion models includes the US EPA?s Industrial Source Complex Model (Version 3), the AERMET/AERMOD suite of models and the CALMET/CALPUFF suite of models. Guidelines are also proposed for environmental exposure assessments including cancer and non-cancer health effects.

Jan 1, 2004

By J. Matos e Silva

"Abstract Although one can think that it is very low the probability of a seism occurrence during the execution of an excavation in an urban lot protected by a diaphragm wall curtain, reality shows that whenever a seism occurs in an urban area several diaphragm walls will be affected by it. So it is advisable to consider the seismic action when designing a diaphragm wall curtain. The paper refers the main information about the seismic design of diaphragm walls according to the Eurocodes 7 and 8 and to the Portuguese Norms related to them (respectively NP EN 1997-1 2010 and NP EN 1998-5 2010), as the Eurocodes consider the possibility of each European country to adopt their own seismic parameters as the seismic risk is different in each country. Thus the so-called National Document of Application (in our case the Portuguese Norms) prescribes the seismic local parameters.1 - EUROCODES AND PORTUGUESE NORMS PRESCRIPTIONSAccording to Eurocode 8 - Part 5 and to the related Portuguese Norm NP EN 1998-5 2010, seismic actions on soils should be quantified adopting the Mononobe-Okabe method that gives goodapproaches when compared with reality.From paragraph 7.3.2.2 of the referred Norm, the horizontal seismic coefficient kh will be:"

Jan 1, 2014

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

By H. M. Smith

MORE than a year before the United States entered World War II, the requirements of the National Defense Program indicated the need for additional sources of aviation gasoline. On September 10, 1940, Dr. R. E. Wilson, Group Executive, Advisory Commission of the Council for National Defense, requested the Bureau of Mines to undertake a survey of crude oils of the United States to designate those suitable for the production of 91-octane aviation gasoline. As quickly as a program could be defined, agreed upon, and funds provided to conduct the work, the Bureau began the project. Over a period of many years the Bureau had collected samples and made analyses of thousands of crude oils produced in the United States. Although these analyses did not include octane numbers of the gasoline fraction, they provided data necessary for calculating the correlation index. This index, developed within the Bureau, is a measure of the types of hydrocarbons present in gasoline and therefore is roughly indicative of the octane value. This fund of information from Bureau of Mines Hempel analyses, supplemented by information obtained from oil companies, reduced considerably the necessary laboratory work by providing data that permitted a large number of crude oils to be eliminated from consideration. However, in the survey carried out during the last part of 1940 and the first half of 1941, 225 samples of crude oil were collected and distilled. Octane values of the distillates were determined by the Army AFD-1C method. (See page 57.) A report containing these results, together with the calculated amounts of 91-octane aviation gasoline available from these sources, was prepared and distributed to the several offices of the Office of the Petroleum Coordinator for National Defense in August 1941. In December 1942 the Office of the Petroleum Coordinator for National Defense became the Petroleum Administration for War (P. A. W.).

Jan 1, 1951

By Joe F. T. Agapito

High stresses and adverse geology in deep coal mines in the state of Utah, USA, have caused numerous bumps. The larger bumps have been associated with seismic events with Richter magnitudes of 3.6 and greater, and in some cases have filled openings for lengths of 150 m. A better understanding of the mechanisms and stress levels involved in bumping is needed to help develop improved stress control design and bump mitigation methods. The geology of the area is notoriously bump-prone. The coal has poorly developed cleating and occurs in multiple seams that are often bounded by very strong roof and floor sandstone/siltstone beds. The overburden is formed by thick, competent strata with numerous sandstone channels This geology and deep cover are the major source of high stresses, causing bumps. This paper evaluates live common stress factors responsible for bump problems: depth, sandstone channels, arching, faults, and coal thickness. It uses ease study data from longwall panels with two-entry/yield pillar systems typical of deeper Utah mines. Results illustrate the importance of analyzing stress factor experience to allow a better understanding of the problem.

Jan 1, 2000

By Joshua Taylor Drake

This report answers specific questions concerning underwater blasting considerations, and blasting safety. The blasting considerations discussed consist of basic blasting principles, and new variables to be accounted for. Blasting safety will include the safety of personnel and structures. The environmental considerations will also be discussed with mitigation methods. To be most effective, this document requires the reader to be familiar with key fundamentals of explosive engineering. In order for a blasting professional to benefit from this report, the following questions will be asked:

Jan 1, 2015

By T. M. Barczak, S. C. Tadolini

Reduction in the recovery time required and improvements in safety during a longwall face move have compelled coal mine operators to examine and use pre-driven longwall recovery rooms. The recovery entry is developed at the longwall stop position and supported ahead of time so that the required combinations of standing and internal supports can be installed before the longwall face approaches. A calibrated three-dimensional finite element model, developed in conjunction with an underground test area, provided the critical components and design principals for a comprehensive parametric study. The study indicates that vertical, horizontal, and shear stresses concentrated on the outby abutment pillar corner of the recovery room resulting in deformations in the immediate roof above the primary roof support anchorage level. The results of the numerical model and field site observations indicated that the combination of the internal bolting system and the standing concrete supports are critical for the successful and safe extraction of the longwall equipment. Cable supports installed at and angle over the pillars can help stabilize the disturbed zone above the adjacent fender and outby pillars, however; standing supports are required in most sedimentary roof conditions to increase stability and assure a safe longwall extraction.

By Edmond Chin

The area encompassed by the political entities included in this study com-prises 11 million square miles or about 15 percent of the total Earth's land area. The bulk of the region is contained on the Asian continental land mass. Australia, the world's largest is-land or the world's smallest continent, alone is almost as large as the continental United States. The islands of New Zealand, New Guinea, Borneo, Sumatra, and Honshu are among the largest in the world. Collectively, they constitute a land area of 1.1 million square miles or an area about one-fourth the size of the United States. The region is noted for its great rivers. The Chang, Huang, Amur, and Mekong are respectively the fifth, sixth, eighth, and eleventh longest rivers in the world. The Ganges-Brahmaputra has created the world's largest delta, which covers 30,000 square miles. Abutting East Asia are the Sea of Japan, Dong Hai, Nan Hai, Bay of Ben-gal, and Arabian Sea. In the Southern Hemisphere, there is the Indian Ocean and the South Pacific Ocean. The Continental Shelf adjacent to the region constitutes a large proportion of the world's readily accessible shelf area. On the other hand, the Philippine and Java trenches and, further out, the Mariana Trench reach to formidable, abyssal depths, downward to 6,000 fathoms. Contrasting to this is Mount Everest, which reaches a lofty height of 29,028 feet. And then there is Xizang, whose high plateaus have been called the roof of the world.

Jan 1, 1992

By S. Banisi, M Nesari, J. A. Finch, N. Nobari, H. Javani

"The flotation circuit of the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9% Cu, consists of rougher, cleaning and recleaning stages. Mechanical flotation cells are used in all stages. To investigate the amenability of flotation columns in the plant especially for cleaning and recleaning stages, a column was designed, constructed, and installed at the Sarcheshmeh pilot plant. The pilot plant, which has an identical circuit configuration compared to the plant, can process up to 2 t/h of ore. The overall rate constant of the ore along with the target recovery of 94% were used to size the column. A 26 cm by 550 cm column with two filter cloth spargers and a submerged froth washing system using perforated tubes was constructed. To detect the interface level a 180 cm conductivity probe consisting of 1.5 cm diameter ring electrodes was installed. The tailings flowrate controlled by a variable speed pump was used as the main control variable. The initial testing program revealed that the optimum superficial gas and wash water flowrate were 1.5 and 0.3 cds, respectively. It was observed that the cleaning stage grade when using the column could increase by 2-3% at constant overall copper recovery.IntroductionThe Sarcheshmeh copper ore body which may rank as third or fourth largest in the world contains 1 billion tomes averaging 0.90 % copper and 0.03 % molybdenum. It is in located south-east Iran and has been processing 40,000 t/d of ore since 1982. After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailings constitutes the main component of the plant final tailings. A concentrate with an average grade of 31% Cu (chalcopyrite and chalcocite) is obtained after cleaning and re-cleaning stages in mechanical cells. Total recovery of the plant varies between 83-87 % depending on ore type and operating conditions."

Jan 1, 2000

By Garry M. Johnston, Matthew L. Sutcliffe, Nicholas J. Welham

"The predominant current processes for the treatment of oxidized copper–cobalt ores use a reductive acid leach to bring the desired metals into solution. However, the indiscriminate nature of acid leaching results in a solution, akin to a metal soup, containing not only the Cu and Co but also an extensive suite of other metals. These other metals, notably Fe, Mn, Al, Ca, Mg and Si, all have to be eliminated from solution before the copper and cobalt can be recovered. Generally precipitation processes are used, but these tend to result in significant losses of copper and/or more usually cobalt from solution, leading to reduced recoveries. The AmmLeach® process uses ammonia-based chemistry to selectively leach the target metals, leaving the rest behind in the leach residue. This approach eliminates any need to clean the solution of unwanted metals and the consequent metal losses. After solid–liquid separation, the leach solution is immediately subjected to separation and concentration of the copper and cobalt using solvent extraction and electrowinning. INTRODUCTION The Copper Belt extends through the northern part of Zambia and the southern province of Katanga in the Democratic Republic of Congo (DRC) and contains the richest and highest grade deposits of copper and cobalt remaining in the world. Whilst there are a number of mines that produce sulphide concentrates, using froth flotation, the largest deposits are those where near-surface sulphides have been weathered over time to form oxides. The oxides cannot be concentrated by conventional physical means to give high recoveries. Despite this, a number of dense medium separation plants have been installed and used to produce a higher grade concentrate which is typically exported (while the rejects, typically 2 to 3% Cu are stockpiled for treatment at a later date). These plants generally have low recoveries and can only be used on the dwindling supply of high grade materials. In exporting the concentrate, little value adding is undertaken within the country, thus greatly reducing the economic benefits to the country. Recent changes to the regulations in the DRC will effectively ban the export of low value ores, concentrates and intermediates in favour of high value metals. This will necessitate mines to install new processing circuits in order to comply with these regulations. The head grade of ores currently being treated in the DRC is slowly decreasing as the extremely high grade materials are being selectively mined out. In many cases, the removal of a small volume of high grade materials leaves a much larger volume of economically marginal ore behind. This is due to a desire for short-term profits overtaking long-term prosperity. The remaining ore, which in many cases is still of relatively high value by world class standards, is likely to be only treatable by low cost heap leaching. There are some initial trials of heap leaching within the DRC, but implementation at a large scale has yet to be adopted."

Jan 1, 2015

By George A. Burrell, G. W. Jones, Frank M. Seibert

In this bulletin, the style of Bulletin 42 has been closely followed. Much of the material is reprinted on the following pages in its original form, and changes have been made only where manifestly neces- St,ry. Laboratory methods have been brought up to date. Some types of apparatus described in Bulletin 42 have now become obsolete and newer designs are described instead. The authors hope that this bulletin will be of as much service as was Bulletin 42.

Jan 1, 1926

By R Sridhar, M Fe, W G. Bacon

The problems of magnetite build-up have plagued the non-ferrous pyrometallurgical industry for many years. To better understand these problems, a study was undertaken to determine the thermodynamic variables that affect the behaviour of magnetite under different smelting conditions. Equilibration studies were performed in the nickel smelting systems of matte-gas and matte-slag(silica saturation)-gas. The relationship of thermodynamic variables such as temperature, sulphur and oxygen partial pressure and matte grade on iron and magnetite activities were calculated and the significance on smelting parameters such as metal losses and partition coefficients were defined. The experimental data from this study were employed to develop practical methods which could be used to control the build up of magnetite, as well as to obtain additional metallurgical benefits. In general, a lower sulphur partial pressure and higher temperature operation was shown to enhance the metallurgical benefits of nickel smelting by decreasing the magnetite activity. Operating in this manner can also have added benefits such as higher metal recoveries, more efficient vessel utilisation and efficiency and lower smelter emissions at equivalent or higher primary furnace matte grades.

Jan 1, 2000

By J S. J van Deventer

Geopolymerisation is a new technology that processes and transforms aluminosilicate minerals into mechanically strong and chemically stable products. In this investigation, minerals such as fly ash and kaolinite were used as the solid raw materials for geopolymerisation. Inorganic salts were added to the geopolymeric pastes to simulate ionic contamination during processing for building and construction applications. The resultant products were examined and characterised physically. It was found that the early strength development of geopolymeric pastes could be changed according to the nature as well as the extent of the contamination. At a small dosage, the effect of the contamination on the early geopolymeric system depended heavily on the nature of the artificial surfaces that were created in the geopolymeric solution through the addition of the chemical additives. For example, the samples containing MgCl2 and Mg(NO3)2 had shown the same yield stress developments due to the similar surfaces that were formed. The cations of these salts were expected to hydrolyse and form magnesium hydroxide precipitates immediately after the addition to the early geopolymeric systems. The calcium cations of CaCl2 also precipitated upon addition, but the nature of the surfaces of these hydroxides was quite different to those of the magnesium hydroxides and gave rise to different yield stress development. The samples that contained the insoluble salts (in water) demonstrated different yield stress development when compared to each other because of the different nature of the additive surfaces that were exposed to the geopolymeric solution. These results suggested that heterogeneous nucleation could be responsible for the change of the rheological behaviour upon inorganic salt addition. When the extent of the ionic contamination was large, the anions released from the insoluble salts (in water) changed the nature as well as the concentration of the geopolymeric solution and the setting processes were retarded. Oxides, in general, behaved very differently from other salts, indicating the uniqueness of the oxygen anions in a system rich in hydroxyl and silicate anions. The inorganic salt contamination in geopolymers did not show any significant signs of structural change according to the XRD diffractograms collected. The seven-day compressive strength was not lowered by the inorganic salt contamination and it could sometimes be beneficial to the product performance, for example, an increase of 20 MPa was induced by the addition of calcium oxide. Inorganic salts as chemical additives have demonstrated the potential to modify setting times of geopolymers without sacrificing much of the productsÆ strength and integrity.

Jan 1, 2000

By S. O. Castro, R. E. González, L. E. Velasco, J. M. Van Sint, P. V. Lois

Abstract Several zones with expansive rocks were encountered during construction of two tunnels of the water conduction system for the Chacabuquito Hydropower Plant, located in the Aconcagua river valley of the Chilean Central Andes Mountains, at elevation 1.075 m a.s.l., and 65 km north-northeast of Santiago. The expansive behavior was associated to three different geological features. Firstly with the crossing of important north-south trending faults, with montmorillonitic and caolinitic fillings. Secondly to the presence of zones of rock mass showing a penetrative presence of clay minerals (montmorillonite, illite and caolinite) and penetrative thin veins of ceolites. And thirdly to the hydrothermal alteration of the rock and the consequent generation of clay minerals (predominantly montmorillonite, sericite and minor caolinite). The geological and mechanical characteristics of the expansive rock domains, as well as the field and laboratory reconnaissance and characterization program, are described in the paper together with the bases for design and the guidelines for construction and definitive tunnels support. Resúmè Pendant l’excavation des deux tunels du système d’adduction d’eau pour alimenter la centrale hidroélectrique Chacabuquito, plusieures zones de rochers expansifs ont été découvertes. Ces tunnels sont dans la vallée du fleuve Aconcagua de la Cordillère des Andes du Chili Central, à une altitude aproximée de 1.075m s.m.n. et à 65km vers le nord-nord-ouest de Santiago. Cette conduite expansive est associée à trois différentes caractéristiques géologiques du massif rocheux. Un premier lieu, à l’intersection de plusieures zones de failles, d’orientation nord-sud et subverticales, avec remplissage de rochers désintégrés, montmorillonite, caolinite et sérite. En seconde lieu, a la présence de zones de rochers expansifs, avec des nombreux minces veines de céolite-calcite et aussi des minéraux argileux (montmorillonite, illite et caolinite). Et, dans troisième lieu, dût à la présence de zones d’altération hidrothermale du massif rocheux et la conséquente génération de minéraux de remplacement argileux (surtout sérite, montmorillonite et en plus petit degré, caolinite). Les caractéristiques géologiques et géomécaniques des rochers expansifs, ainsi que la reconnaissance du terrain et les résultats du programme d’essais de caractérisation géomécanique du laboratoire sont décrits dans ce travail, ainsi que les bases de dessin et recommandations constructives pour placement du support définitifs pour ces tunnels Zusammenfassung Während der ausgrabung der zwei tunnels der wasserleitungssystem, um die Chacabuquito Wasserstromzentrale zu besorgen, wurden verschieden ausgedehnte gesteinadern gefunden Die beiden tunnels befinden sich im Aconcaguatal, wo der Aconcagua Fluss fliesst, auf einer Höhe von 1.075 m über dem Wasserspiegel und ca. 65 Km Nord-Nordest von Santiago entfernt, in mittleren Anden Cordillere (chilenische Gebirgskette). Drei verschiedene geologische merkmale dieser massiven gesteine können dieses ausgedehnte verhalten erklären. Erstens, hier befinden sich verschiedene und auch ganz wichtige

Jan 1, 2003