Search Documents

By Serge Moalli

The Ashlu Creek Hydro-electric project, located north of Squamish, BC, at the confluence of Ashlu Creek and the Squamish River, comprises a 49 MW run-of-river project and features a 4.08 m diameter, 4.4 km power tunnel and a 128 m deep drop shaft. The Ashlu Creek Hydro-electric project is being developed by Innergex under Ashlu Creek Investments Limited. Site civil works are being completed by Ledcor CMI of Vancouver with tunnel construction by Frontier Kemper Constructors ULC under a lump sum design-build contract. Site works got underway in September 2006 with the construction of the tunnel portal and laydown area. These site works required rock slope stabilization over a 50 m rock slope to secure the laydown area as well as the construction of a tail track muck tipping station and structural wall to facilitate TBM excavation and spoil removal. Starter tunnel construction commenced in early 2007 and TBM tunneling started in the late spring of 2007 and is planned to continue until early 2009. The power tunnel is being excavated using a 1,200 kW Wirth open-type hard rock TBM dressed with 31?17' cutters. The TBM featured two fixed mounted rock bolt drills behind the finger shield: these were removed and replaced with jacklegs to improve access. A probe drill at the end of the main beam is also present. The geology along the 4.4 km power tunnel comprises very strong and generally massive granitic bedrock with rock strength greater than 225 MPa. A unique feature of the project is that no subsurface investigations have been completed for the tunnel however extensive bedrock outcrops are present along the Ashlu Creek valley. A historical quarry exists approximately mid-way along the tunnel alignment that has exposed good quality granitic bedrock. TBM tunneling to date has achieved advance rates of 10?20 m/day with a maximum of 23 m and has encountered all of the anticipated six major fault zones where the installation of various standard high capacity tunnel support was successful to facilitate TBM advance through these sections.

By Gorr W. W., Wyche E. H, R. Smith

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By Gorr W. W., R. Smith, Wyche E. H

The combination of high strength and corrosion resistance of cold-worked 18 Cr, 8 Ni steel has been advantageously utilized for some time, particularly in aircraft and rail car structures. There are, however, certain limitations on the use of such materials because the high strengths can be obtained only by cold-working, limiting the available products to sheets, strip, wire and tubes. The authors sought to overcome these limitations by resorting to precipitation-hardening, which has been used so successfully in nonferrous metallurgy but only to a limited extent in iron-base alloys. Accomplishment of this objective not only overcame the limitations, but also effected certain improvements in mechanical and other properties. This paper is an account of the development by Carnegie-Illinois Steel Corporation of a precipitation-hardening 18-8 stainless steel (called Stainless W‡ and tentatively identified as type 322). A description is given of its composition and metallurgical characteristics, heat-treatment, physical and mechanical properties and corrosion resistance. Development of the New Steel For a considerable length of time the authors were unable to determine the mechanism of the precipitation-hardening process that had been noted by Ffield18,19 in 18-8 Ti or 18-8 Cb after cold-working and reheating to moderately elevated temperatures. All known variables were exhaustively studied, but with little success. However, results began to indicate that chemical composition was the most important variable, particularly the ratio of austenite-forming to ferrite-forming elements. The investigators then focused their attention upon the composition, and, in particular, upon the element titanium and its mode of alloying in the presence of other elements. A heat was obtained that could not be brought to the softness level of annealed 18-8. The response to cold-straining and aging* was very marked by previous standards, and, more important, cold-straining was found to be entirely unnecessary to produce the precipitation-hardening effect. The chemical composition of this heat was: C, 0.06 per cent; Mn, 0.54; P, 0.016; S, 0.016; Si, 0.58; Ni, 7.28; Cr, 17.60; Ti, 0.90; Al, 0.17. For some time the development work, particularly on composition, was carried

Jan 1, 1947

By Thomas E. Popplewell

This paper is one of a series being prepared for and published by the United States Bureau of Mines describing the mining and treatment methods and costs obtained in sand and gravel plants throughout the United States. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By R. Strandahl

As one of the largest private utilities globally, E.ON currently operates hard coal fired power stations in with a total installed capacity of some 20.000 MW: These thermal power plants consume domestic coals but are increasingly dependent on imported seaborne traded coal (in 2009 approx. 17 million t). Knowing that the company’s reputation and credibility depends in part on how E.ON lives up to the responsibilities along the entire energy value chain, E.ON takes a collaborative approach with the various suppliers. Hence, E.ON’s responsible policy also applies to the procurement of coal; the utility launched in 2009 a comprehensive Corporate Responsibility program with special focus on supply-chain audits. One of the first coal audits focussed on the Cerrejón coal mine in North Eastern Colombia. The authors will share the key learning’s and experience from the Colombian audit jointly conducted with an independent auditor and E.ON experts from the Corporate CR and E.ON Energy Trading.

Jan 1, 2011

By S. Banisi, H. R. Iran-Manesh, M. R. Shayestefar, H. Shekarchyan

"Flotation circuit of the Sarcheshmeh copper mine processes 41,000 t/d of ore at 0.9% Cu. Chalcopyrite and chalcocite are the main copper bearing minerals which are concentrated in three stages of roughing, cleaning and recleaning. Due to major changes in the reagent addition regime, make-up balls combination, and throughput to the primary mills an increase of 2.6% (from 87.2% to 89.8%) in the sulfide copper recovery was obtained during a period of six years. In order to investigate a rather large variation of monthly recovery (i.e., from 89.0 to 91.2%) of the plant after implementation of the changes, a study was undertaken to trace mineralogically possible causes of such a behavior. During a five-month period, monthly composite samples of feed and tailings of the flotation circuit were taken. At the first stage, the polished sample preparation method and the mineral counting procedure were optimized through a detailed study. Liberation degrees and types of locking of valuable minerals in both streams were determined in three size intervals of +75, +38 and –38 microns. It was found that for both recovery levels (i.e., 89% and 91.2%), there was no significant difference in the liberation degrees of valuable minerals in the flotation feed; the average liberation degree was 57.1% with a standard deviation of 3.1%. On the other hand, in the case of high recovery level (i.e., 91.2%) there was a reduction of 15% in the amount of free valuable minerals in the tailings stream. The highest reduction was found for the -38 micron size range in particular for chalcocite. It was concluded that compared to the grinding circuit the change in the flotation circuit had the significant effect on the plant recovery increase.INTRODUCTIONThe Sarcheshmeh copper ore body contains 1 billion tonnes averaging 0.90 % copper and 0.03 % molybdenum. It is located southeast of Iran and currently processes 41,000 t/d of ore. The concentrator has been in operation since 1982. Last year, the concentrator produced 130,000 tonnes of copper and 4,000 tonnes of molybednite concentrate. An expansion to the plant which will increase the throughput by 50% is under construction and will be effective in 2003.After three stages of crushing, the ore with a F80 of 12.7 mm is fed to 8 parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of the first stage of flotation is reground and the tailings constitute the main component of the plant final tailings. A concentrate with an average grade of 30.5% Cu is obtained after cleaning and re-cleaning stages. At the present time, the average sulfide copper recovery of the plant is 89.8% which varies depending on the operating conditions and ore type."

Jan 1, 2003

By Cassandra A. Wetzel

Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.

By Mervin D. Marshall

A quick-reaction, mine permissible rescue vehicle (MERV) was developed for use by rescue teams. The MERV is a 6-wheeled, battery-powered unit with life support equipment and instrumentation; designed for a two-man team, with provisions for handling two victims or tools in a trailer. The vehicle is 100 inches long, 56 inches wide, and maximum height of 34 inches. It can be lowered down most mine shafts and has clearance to travel mine railways. The vehicle has power to all six wheels with power transmitted separately to either or both sets of wheels. Low-pressure, high-traction tires give the vehicle the ability to handle soft, muddy mine floors, flooded areas and significant obstacles, and can negotiate a 45% grade. Power and life support are sufficient for a 4-hour mission. The life support system is a commercially-available, approved unit currently used by MESA rescue personnel. A payout wire system provides communication between the vehicle and home base over a distance of 10,000 feet. On-board monitoring of carbon monoxide, methane and oxygen is provided, with master and individual alarms to warn of gas concentrations outside pre-set limits. A lightweight, water-tight trailer was developed for carrying victims or hauling tools and equipment.

Jan 1, 1979

By Robert J. F. Goodfellow, William A. T. Meakin, Kevin Clarke, Eric Cole

INTRODUCTION New York City Water Supply—Background and History Since the 1840s New York City has been developing the largest, and perhaps, the best urban water supply and distribution system in the world in terms of quality and reliability. One of the engineering marvels of the modern world, the New York City water supply and distribution system serves a population of almost nine million, including residents in nearby Westchester, Putnam, Ulster, and Orange Counties of New York State. The average daily supplies presently are running at almost 60 m3/sec(about 1,350 million gallons per day). The watershed for the New York City water supply system, under the jurisdiction of the New York City Department of Environmental Protection (NYCDEP), consists of19 reservoirs and three controlled lakes, and covers an area of approximately5,000 square kilometers (about 2,000 square miles) north of New York City. The watershed total available storage capacity is about two billion cubic meters (560 billion gallons) and is divided into three reservoir systems: the Catskill and Delaware watersheds located West of the Hudson River; and the Croton watershed, located east of the Hudson River, see Figure 1. The first element of the system, the Croton Aqueduct, started operations in 1842.Through several updates and expansions, the present-day Croton system was in place by 1911, providing a potential maximum supply of about 15 m3/s (about 340 mgd). The system includes ten reservoirs and three controlled lakes. In the late 1800s, with the tremendous growth of the City, New York City water engineers began to look for additional sources. Between 1907 and 1929, the City acquired water rights and constructed a new 148 km (92 miles) Catskill aqueduct to convey water from the Ashokan Reservoir to the City. The Catskill system also included the construction of the Kensico and Hillview Reservoirs just north of the City,

Jan 1, 2005

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitlted "Evaluation of Proximity Warning Devices II dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electro-static fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factory of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

Neutralization with lime is a simple, cheap, and effective means of treating acid raffinates from uranium processing to' raise the pH, reduce the concentrations of dissolved salts (including heavy metal impurities), and remove amine by adsorption. Two-stage neutralization, using limestone in the first stage at approximately pH 4 and lime in the second, lIlay be advantageous.Lime neutralization of mffinates in the pH range 7 to 8· 5 generally reduced the radium ·concentration to 10 to 200 pCi 1-1, but ·there was considerable scatter in the experimental data. The radium concentration was further reduced to less than 3 pCi 1-1 by co-precipitation of barium (radium) sulphate with 10 mg Ba (as barium chloride) per litre of raffinate. Adsorption of radium on barytes was -also effective in reducing the radium concentration in neutralized raffinate to less than 3 pCi 1-1.The radium concentration of pit water was readily reduced to less than 3 pCi 1-1 when pit water containing 0·01 M sulphate as ammonium, calcium, or sodium sulphate was treated with 20 mg Ba per litre of pit water.Adsorption on barytes was also effective in removing radium from pit water containing 0·03 M sulphate.

Jan 1, 1975

Fine Coal Evaluation by Gravity Methods

Sep 13, 2010

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for a longwall mining operation in the Northern Appalachian Coal Region. Vertical displacements and relative faze positions are tabulated for 160 subsidence monuments. Measurements were taken 32 times during the 2 years it took to mine the two panels. Brief physiographic and geological descriptions of the mining site are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

Operational effectiveness is fundamental to any operation, becoming highly topical in those experiencing less than optimal output from their fleets. It is all encompassing aiming to identify those factors that could be improved within production and suggesting solutions in order to optimise the existing fleet and obtain the greatest capital return on expenditure.Argyle Diamond Mine (ADM) is a large open cut diamond mine located in the East Kimberley region of Western Australia, approximately 180 km south of Kununurra. It is owned and operated by Rio Tinto on a two week on/two week off roster fly-in/fly-out from Perth or drive in/drive out from Kununurra. Through benchmarking the operation between January and June 2002, a study was undertaken allowing identification of areas falling below target. Following this, analysis of annualised hours and production downtimes were undertaken to quantify the potential gains of improvements in these areas. Strategies were then identified as stated in the 2002 mine plan, in operational effectiveness meetings, and by staff members. This project aimed to maximise direct working hours through determination of the main issues hindering performance. External and internal factors were considered and a continuous improvement program (CIP) was developed. The CIP aimed at internal site-based improvement teams to identify and implement solutions for improvement on a day-to-day basis.

Jan 1, 2003

Mineral exploration and mining in New Zealand has had almost five years of new legislation. The requirement for different consents is a challenging, time consuming, expensive exercise but in most cases the new procedure is working, although the matter of obtaining access to land is still a major issue. Priority is critical. After lodgment of an application for a minerals permit there are many other matters to address such as identifying land owners, occupiers and administrators, preparation of access applications, consultation and preparation of various resource consent applications.

Jan 1, 1996

By Sayavur Bakhtiyarov

Keywords: Rheology, Viscoelastic, Oil In this paper we present the results of the rheological property measurements on viscoelastic composite materials used in oil industry. Laboratory experiments were carried out to determine important thermophysical, rheological and mechanical properties of the test materials using both the standard commercial and in-house made equipment. The composites with the paramagnetic particles (?-iron oxide) are exhibited a significant magnetic memory after magnetic treatment. The measured value of the yield stress after the magnetic treatment increased almost twice in comparison with the yield stress value of the magnetically untreated composite. The yield stress of the composite material exponentially decreases with time and reaches its magnetically untreated value after 15 hours. The yield stress also increases with the amount of the paramagnetic powder additive, and it reaches a maximum value at 8 wt-% of this additive. The obtained results provide valuable information for computer modeling of the viscoelastic fluid flow in pipes of complex geometry.

Jan 1, 2005

Owing to improvements in computer capacity, it is now possible to undertake fully coupled or partially coupled, three-dimensional (3D) hydromechanical Finite Element (FE) simulation of mines, including explicit representations of large numbers of discontinuities. The analysis requires fewer assumptions than uncoupled analysis or two-dimensional (2D) analysis, but may require a change in how hydrological data is collected. The way hydrological data is incorporated in stability assessment and the approach to uncertainty in hydrological information also requires discussion. The current procedures for this type of analysis are discussed, along with some practical difficulties and teachings from early applications. A work flow for integration of 3D hydromechanical modelling with pit planning and some considerations for the management of uncertain data are also proposed.

May 1, 2010

By S. G. Hardcastle, C. K. Kocsis

"Worldwide, metal mines are going deeper. For example, in Canada there are six such mechanized mines planning production at 3000 m (10 000 ft). Working at such depths challenges all aspects of mining including the provision of ventilation to supply an equitable working climate for personnel and machinery.This paper explores the overall challenges of supplying ventilation in Canada’s deepest mines and how the volumes required could be minimized. This is essential because it must be remembered that ventilation and refrigeration are not only costly items to supply, but the magnitude of their cost is also very sensitive to the volume supplied. For the primary ventilation system this is obvious because of the cubic relationship between volume and cost.In deep mines, the main function of ventilation is the removal of heat transferred from the strata and generated by the mining machinery, and the air volumes supplied are designed accordingly. The second consideration is the removal of other pollutants that could be harmful to humans such as diesel and explosive fumes. However, the need for ventilation at its present design levels could be reduced. This paper discusses the implications of such technologies as: tele-remote mining and alternatives to diesel equipment on the magnitude of the volume supplied; ventilationon- demand which recognizes ventilation as a costly and limited resource; plus other aspects, such as the benefits of controlled recirculation, local cooling, and possibly heat rejection back to the strata to gain further advantage from new developments.Furthermore, this paper advances the need to be able to design ventilation systems more cost effectively and how such new advances as process simulators can be used in conjunction with ventilation simulators to explore the diverse options that could affect the air volumes required and provide more realistic economic data upon which to base design decisions."

Jan 1, 2004

By G C. Sen

All mining and quarrying operations that employ blasting to fragment and move broken ground have a price to pay for æby-productsÆ such as vibration and noise. These æby-productsÆ cannot be eliminated but they can be controlled and modern blasting techniques have improved to the point that excessive environmental restrictions can be adhered to whilst maintaining acceptable production rates and quality. Accurate measurement is the key to control, and as the environmental limits are becoming tighter, the proper way to measure vibrations from blasting operations becomes an integral part of the mining or quarrying operations. The basic vibration monitoring system consists of a primary sensor connected to a data logger and computer software for the analysis of the signal received and recorded. Currently, as with all fields of measurement, much improvement has occurred over the past decade, and electronic devices are much more accurate and reliable. Data analysis has also improved considerably with the computing power that is available to field operatives today. Mounting the primary sensor has been often overlooked in supposed æstandardsÆ with procedures such as double sided tape, resting on a flat surface provided the vibration level is less than a given amount. But if it is worth going to the expense of the monitoring equipment and manpower, surely it is worth a little extra effort to ensure the primary sensor is coupled to the ground effectively. The primary sensor must move with the ground and measure this movement; so if the primary sensor is allowed to move without respect to the ground (ie poor coupling to the ground) then a false record of the physical event will be measured. This scenario can easily be a practical reality if the primary sensor coupling method to the ground is not effective. In this study a number of mounting methods were fabricated and connected to similar data monitors and a series of ænormalÆ production blasts were used as the vibration source. These mounting devices were measured against an in-house procedure (the æstandardÆ) and the relative merits compared. A laboratory investigation was also carried out to look at the physical parameters of the æsoil and their effect on vibration attenuation of the in-house standard method.

Jan 1, 1999

By Jose R. Hernandez-Aguilar

"This paper revisits data from previous studies (Hernandez-Aguilar, 2010, 2011) to better understand the link between metallurgical performance and pulp-zone bubble size (Db) in full-scale flotation systems. To obtain conclusive evidence exclusively related to the pulp (collection) zone, the experiments were designed in those studies to control both the bubble generation method and the influence of the froth zone on the overall metallurgical performance in industrial and pilot-scale flotation columns. The results showed that Db had a significantly larger effect on the recovery of coarse (> 75 µm) particles compared to the effect on fine (< 16 µm) particles. It was observed that, under certain practical conditions, the recovery of coarse particles was close to zero, but dramatically increased by reducing Db. The evidence revealed an inconsistency of the so-called “k–PSb” model: at constant froth recovery, increasing Sb (i.e., the rate of production of bubble surface area) did not always result in higher recovery, as the model predicts. Furthermore, the evidence showed that it was not the Sb but the bubble size that proved to be a more reliable link to metallurgical performance. Only in the presence of suboptimal-sized bubbles (Db > 2 mm) did the froth zone seem to play a role, possibly reflecting an effect of pulp-zone bubble size on froth stability. However, the role of the froth was negligible for Db < 1 mm.High-resolution mineralogical measurements performed on process samples revealed that, regardless of the degree of liberation, Db had a profound effect on the shape of the recovery-by-size curve, particularly the coarse particle size fraction. This observation is key as it implies that the loss in efficiency associated with floating the coarse particles was not the result of neither particle hydrophobicity nor particle detachment issues: even in the absence of mechanical agitation, liberated and highly hydrophobic coarse particles did not seem to attach to the bubbles in the first place, an inefficiency that was corrected by reducing bubble size. The data analysis suggests that poor attachment efficiency can practically affect both fine and coarse particles but via different mechanisms which are discussed here."

Jan 1, 2017