Search Documents

By Nathan Feldstein

The wetting of coal dust by aqueous solutions of surface active agents (surfactants) has been studied. Selected for study were thirty coals and typical surfactants selected from the typical classes of anionic, non ionic and cationics. Of these three classes the practical use of cationics in aqueous solutions has been eliminated due to the inherent negative Zeta potential charge of the representative coals studied. The wetting of the coals has been examined by column flow, contact angle, and settling rate measurements. Results indicated that both anionic and nonionic surfactants are to be considered viable for use; low critical micelle concentration values are also preferred for the surfactants. Study of native waters showed substantial variation in properties, i.e., pH, calcium ion concentration, and conductance. pH variations were also noted to affect the effectiveness of selected surfactants. Combinations of nonionic and anionic surfactants have, in certain instances, produced synergistic enhancement in the coal wetting superior to the effectiveness of each surfactant alone.

Jan 1, 1981

By R. J. Hundermark, S. Sun

The oxidation state dependence of the electrical conductivity of a calcium ferrite slag with 25 wt% CaO was measured at 1300°C using a shallow slag layer and two-electrode technique. The experiments were started in air and the slag was sequentially reduced by means of a controlled gas atmosphere using CO2and CO. The electrical conductivity in air was approximately 300 S/m and increased with reduction to approximately 1900 S/m at a pO2of 10-10atm. The interest in the oxidation state dependence of the conductivity of calcium ferrite slags was to provide a comparison with the conductivity of iron silicate slags and to establish the effect of slag basicity on the electrical conductivity and its oxidation state dependence. The results obtained are discussed in terms of the slag structural information available in the literature. The co-ordination of the ferric ions appears to play a large role in determining the electrical conductivity. Keywords: calcium ferrite, slags, electrical conductivity.

Jan 1, 2004

By C. E. M. Meskers

End-of-life Electronic and Electrical Equipment, o_cially called WEEE, is unjustly regarded as mainly a waste management problem. What is structurally overlooked is the enormous resource impact of these devices. EEE rep- resents a tremendous metal resource, which should be uti- lized through e_ective recycling, which has a much lower environmental footprint than primary production. The actual amount of end-of-life EEE recycled today is embar- rassingly low since insu_cient EEE is collected and part of the collected EEE is exported to developing countries, where it is largely not entering o_cial recycling systems. To achieve a global recycling society issues like technol- ogy, economics, life cycle structure, stakeholder aware- ness and legislation have to be addressed in a global, co-operative manner so that sustainable closed product cycles can be obtained. Requirements for a "global re- cycling society" are de_ned to address today's reality of global ows of used consumer products, taking into ac- count the likely needs of the future.

Jan 1, 2009

By Sushil Bhandari, Amit Bhandari

Drilling and Blasting are core operations in a mine. They impact all the downstream operations and their costs. Digital technologies exist for optimizing both drilling and blasting for many years. However, these technologies have largely been non-integrated and non-real time. This gap results in sub-optimal drilling and blasting operations. Also traditionally focus has been on optimizing individual areas (drilling or blasting and subsequent subsystems). Industry has largely lacked real time or near real time integration available to the user in the field and in the office. In this paper, a case study is presented of a large global cement company using a cloud and mobile based platform across 17 of their mines consistently over a large number of users over a period of over two years. The use of a blast platform is detailed which include blast designs, blast data collection and the trends in terms of results. On the drilling side, this paper describes the ability to capture drill logs, plod reports etc. Also actual drilling information in the field using a mobile device and its real time synchronization with a blast designer to provide visibility of expected fragmentation and vibration levels based on the drilling done. Key parameters such as hole ID, design depth, actual depth, hole status, designed and actual charge (length and weight), designed and actual stemming length are captured. The case study also highlights the challenges in technology adoption and implementation in mining in drilling and blasting. Making drill and blast results predictable should be the desired direction. Also digital technology tool adoption has been seen at the biggest miners – not so much in mid-sized miners or drill and blast contractors. Benefits of this platform on the safety side are highlighted including predictions on safety parameters and appropriate alerts if blast safety parameter / clearance zones are not met. The safety parameters are made available visually to the operator using maps and / or on drone images. Future possible improvements in the digital technology platform at the site are also highlighted including greater possible automation.

By B. J. Vorster

AngloGold South Africa region currently consists of twelve gold plants. These plants use a combined total of $20 million of cyanide per annum. Of this, the major portion (60%) is consumed at two Ergo dump retreatment plants. Historically the primary motivation for cyanide control at Ergo has been one of leach/cost optimization. However, more recently, with the increased public awareness of cyanide in the environment, a secondary but increasingly important motivation for control has been to ensure that only the minimum amount of cyanide is added to the process whilst not compromising leach performance. Following a brief overview of the Ergo process, the methodology in determining the amount of cyanide to be added is described. The paper then traces the developments in cyanide control from very basic manual systems to the current automated control system. In line with the increasingly sophisticated control systems, developments also took place in regards to the method of cyanide analysis. The development of these analysers is also discussed. Whilst cyanide is one of the major drivers, if not the major driver of gold dissolution, it cannot be viewed in isolation particularly with respect to the relationship between cyanide and oxygen as ascertained from the Elsner?s well-known equation. Consequently, in order to control cyanide addition, knowledge of the relative cyanide/oxygen profiles is necessary. Various means investigated at Ergo for pulp oxygenation have therefore been included for the sake of completeness. Finally a comparison is made of the control achieved from the current system compared to the original manual system. The knowledge and experience gained at Ergo is now being used to draw up guidelines for the installation and optimization work at the other AngloGold plants. The net effect of this will be reduced cyanide consumption for the region, which also, apart from the obvious economic benefit, translates into a reduced environ-mental risk.

Jan 1, 2001

Allis Mineral Systems ARCO Coal Company Buckley Powder Co. CALCO, Inc. Coal Magazine Colowyo Coal Company Continental Conveyor & Equipment Company Crane & Hoist Sales Cummins Southwest, Inc. Energy West Mining Company Paul J. Epley FMC Corporation The Falkirk Mining Company Fleischli Oil Co., Inc. T. J. Gundlach Machine Company Halbach & Braun Harnischfeger Corporation Hemscheidt Corporation Hyatt Regency Beaver Creek Jennmar Corporation Joy Technologies, Inc. K&P Sales Engineers, Inc. Kennametal, Inc. Kerr-McGee Coal Corporation McLanahan Corporation National Coal Association The North American Coal Corporation Northwestern Resources Company Peabody Coal Company Phillips Machine Service, Inc. Pincock, Allen & Holt, Inc. Pittsburg & Midway Coal Mining Co. Roberts & Schaefer Company Rust Tractor Company Salt River Project Santa Fe Pacific Coal Corporation Schroeder Industries Shearson-Lehman Brothers Southern Pacific Transportation Stamler Corporation Trapper Mining Inc. Wagner Equipment Company Western Energy Company Wheeler Machinery Company

Jan 1, 1992

By G. W. Harris, J. J. K. Daemen

Slightly shorter, modified version also published in CIM Bull., vol.94, no.1047, Feb. 2001, p.52-55. To minimise ore dilution induced by blast movement in surface mines it is necessary to quantify such movement. This will allow more accurate location of the grade boundaries on the surface of a blasted rock pile before excavation. A method has been developed and tested for measuring accurately the direction and magnitude of subsurface blast movement, using a caesium vapour gradiometer and a real-time, differentially corrected global positioning system to locate the pre- and post-blast positions of magnetically enhanced target objects placed in blastholes inside a bench. The procedure does not necessitate disturbance of the blasted rock and the movement information is available sufficiently quickly to allow for modification of the selective mining boundaries for each surveyed blast. It was found that the maximum depth of target detection was 18 m and the overall accuracy was plus or minus 1 m horizontally and 1.2 m vertically

Jun 21, 1905

Introduction Research has shown that when an emergency occurs, work-ers often do not get the information they need to take appropriate action. Important information about incidents is either not com-municated effectively or not at all to those affected by the event. The "Emergency Communication Triangle" safety talk focuses on the content of emergency warning messages. It presents a procedure using mental cues that can be used by senders and receivers of emergency warnings. The talk includes graphics for use during the presentation, as well as references for more information. Background Interviews with 48 miners who had escaped one of three different underground mine fires revealed that warning information provided to them was inadequate. Either insufficient information was provided to miners inby the fire areas or they failed to ask the questions needed to let them plan and execute an effective escape. Most of the miners who evacuated from these three mines did not have information that would allow them to make decisions about efficient escapes. The communication breakdown came from two directions: (1) the individuals providing the warning did not offer details about the situations even though some were known and (2) the individuals who received the warnings did not ask for clarification of the situation. The lack of information allowed miners to continue attempting to place cues into normal frameworks after they should have evaluated the situation as abnormal and threatening. The uncertainty created by the lack of information influenced their decision-making and therefore their actions. Approach Researchers at the NIOSH Pittsburgh Research Laboratory have developed a training intervention that can be used by senders and receivers of warnings during a mine emergency. This material was developed for use in short safety training sessions such as start-of-shift safety talks. The information can be presented in about 15 minutes. Although the illustrations were taken from the underground coal mining industry, the training can be tailored to any work setting by substituting appropriate examples. How It Works During the safety talk, miners learn about the six categories of critical information that should be provided during emergency communications: Who, Where, What, Miners, Event, and Response. • Who: When reporting an emergency or receiving a warning, the first thing a miner must do is identify himself or herself. This is important because people react differently based on who gives them information. • Where: Giving or finding out the location of the problem is important. Of the 48 miners interviewed about their escape, only 2 knew where the fire was located. However, this information was known by either the dispatcher or the person who discovered the fire. • What: Miners must tell or ask exactly what is happening. At one mine fire, miners near the phone heard the message to evacuate and went to gather the others on their crew. One worker shouted to a machine operator: "Come on down to the mantrip. We're going out." Because it was close to quitting time, the machine operator thought they were just leaving the section a little early and went through his normal end-of-shift routine, wasting valuable time. After giving or obtaining the three initial pieces of critical information, miners can then give or obtain details about the response in progress. • Miners: Is anyone hurt? Has everyone been accounted for? When and where was a missing person last seen?

Sep 1, 2004

By J. Patrick Ryan, Thor H. Kiilsgaard, Charles W. Merrill, E. T. McKnight

The U.S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reduc ing demand. This paper examines poss ible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Feb 1, 1965

Pressure drops were measured in a column packed with glass spheres and wax particles, both in random and preferential distributions. Variables investigated included wax content, gas flow rates, and temperatures.It is shown that for random distribution of wax, pressure drop is exponentially related to wax content above the melting point of wax and that below this it increases with increasing gas rate and temperature.For preferred distribution of wax the highest increase in pressure drop is obtained with horizontal distribution of wax and the least with vertical distribution.Comparison with operating blast furnace data and application of results to practice are also included.

Jan 1, 1970

By Greg Smith

This paper documents the use of bench testing equipment developed to enhance the understanding of, and improve upon, common roof bolt support systems. Most roof bolt systems consist of components that are covered within the scope of ASTM (American Society for Testing and Materials) standards. However, ASTM does not specify testing methods or performance standards for complete roof bolt ?systems?. It only designates testing methods and minimum performance standards for roof bolt ?components?. Improved understanding and continuous improvement of these systems is essential given the enormous impact that they have on the safety and profitability of underground mining operations. Bench testing equipment has been developed that effectively measures and records multiple points of deformation in a rock bolt support system while load is being applied. With this testing capability, an improved understanding of component and system stress distribution can be obtained and devices and methods for visual load indication can be developed. This paper is formatted as case studies where testing was performed to demonstrate load versus deformation profiles and to develop system improvement products.

Jan 1, 2012

By C. E. Rork

This paper discusses various mechanical improvements that have been gradually incorporated in the copper-willing plants of the Southwest daring the past 14 years, power plants for concentrators, use of large-size units of equipment, and the effect of plant capacities on costs. The improvements in mechanical equipment and plant design have contributed in the reduction of operating costs; in some instances a saving in the capital cost per ton of daily capacity milled has resulted.

Jan 1, 1935

By R. A. Cummings

Certain roof shales in coal mines deteriorate upon exposure to the atmosphere, causing difficulties in the mining operations and adding to the cost. This report presents the results of both field investigations, in a West Virginia mine, and laboratory studies on the effects of atmospheric moisture on roof shales. Based on these observations a conceptual procedure is presented on how shale deterioration might be predicted during exploration, and guidelines are given as to how air tempering or conditioning chambers may be designed to reduce moisture effects. Recommendations for further studies are included. An annotated bibliography of the literature constitutes the second volume.

Jan 1, 1981

By J. van Deventer

Testwork was done with two different adsorbents, Dowex-Minix gold-selective resin and activated carbon, to detemine their relative performances with regard to gold recovery from clarified low-grade solution employing a fixed-bed operation. The mill discharge from the milling-in-cyanide operation at a Witwatersrand gold mine was used as feed to the adsorption columns. A small amount of gold was leached during the milling process, so that this solution simulates, to a certain extent, a low-grade solution representative of a heap-leach operation. A speciation of the feed solution was done to establish which metal complexes were present in the milling-in-cyanide solution. This information was necessary to interpret metal loadings on the resin, as base metal cyanide species and their respective charges have an effect on the final gold loading capacity of the resin. Equilibrium isotherms were established for both adsorbents to estimate the rate of adsorbent flow anticipated for this specific feed solution. Breakthrough profiles were obtained at two different superficial linear velocities for each adsorbent. Mass transfer zone heights determined from the test work and the elution/regeneration time requirements were used to size a 150 m3/h full-scale plant for both adsorbents. A counter current configuration of adsorption columns, using three columns, should be suitable to recover gold effectively and to produce an effluent with a gold concentration below 0.01 mg/l. Based on the results obtained from the breakthrough tests, a preliminary techno-economic comparison was done between the resin-in-solution and carbon-in-solution options for the recovery of gold from low-grade solutions. This study indicated that the capital expenditure for a carbon-in-solution plant would be about 33 percent higher than that of a resin-in-solution plant. The operating expenditure for a resin-in-solution plant is expected to be only 60per cent of that for a carbon-in-solution plant. Keywords: resin-in-solution, carbon-in-solution, heap leach.

Jan 1, 2000

By Antal Partos

ATLAS Processing Company Shrevesport, LA initiated a major plant expansion in 1980. SITE Engineers, Inc. provided engineering consultation regarding the foundation of the vacuum unit. Four test borings were drilled and laboratory testing completed for shear strength and compressibility. Vertical drains were proposed to accelerate time rates of settlements. Steel erection was completed by May 22, 1981 with very small < 0.1 in., settlements. Hydrotesting was initiated on July 9, 1981 and completed on August 27, 1981. An average rebound of 0.3 in. was computed resulting into an average net settlement of 0.5 in. This paper describes in detail soil behavior during load testing.

Jan 1, 1992

By William R. Yernberg

A conference on coalbed and coal mine methane was held March 27 and 28, 2000, in Denver, CO. The conference, organized by the Strategic Resource Institute, was attended by leaders in the coal mining and gas energy industry. The conference focused on the recovery of methane from coal beds as an energy resource and the removal and utilization of coal-mine methane (CMM) related to underground coal mining. The two-day conference discussed methane resources around the world, methods of recovery, methane markets, underground coal mining, health and safety issues and environmental issues related to methane. The consensus among the presenters is that the future looks promising for coal bed methane (CBM) and CMM.

Jan 1, 2000

By C Doblin

Any value addition to the mineral sands in the Murray Basin (Australia) will generate waste that needs to be disposed of safely. For example, conversion of ilmenite and synthetic rutile to titania (TiO2) pigment would generate large amounts of environmentally undesirable elements. Processing of U+Th containing zircon sands to zirconia or to higher purity zircon would generate a low-level radioactive waste. In this study it is proposed that one way to circumvent the waste problem could be to contain such waste in magnesium-based (Sorel) cements. Containment of waste in magnesium cements is an attractive idea especially for the mineral sand processing companies that could operate in the Murray Basin in the future, because the required magnesium oxide and magnesium chloride may be made cheaply from the saline waters encountered during mining operations. The magnesium cement production process is also far less energy intensive than the Portland cement production process. The results of this study indicate that mixing a waste stream with a slurry of magnesium cement before being discharged to the disposal area would contain the waste in a æconcrete-likeÆ structure, resistant to dispersion by wind and moderate rain. However, some loss of strength and increased leaching of impurities, Mg and Cl could take place in wet climate areas. Ongoing research is being concentrated to develop a new process for making water-resistant magnesium cement.

Jan 1, 2002

By Hao Li, Allan Moss, Richard K. Brummer

At the Palabora Mine, the transition to caving 400 m below the bottom of the 800 m deep pit resulted in a slope failure of the North wall that began in 2003, and is still mobile. This failure can be explained by the daylighting into the cave zone of a prominent joint set. The failure was modelled by the 3-dimensional code 3DEC, which is capable of modelling the nonlinear behaviour of discontinuum materials with large displacement.

Jan 1, 2006

By J. Roth

The purpose of the present study is to increase the safety of explosive storage. This was accomplished by: a) review of the histories of recent and past magazine explosions to define causes and trends; b) observation of present-day explosive storage conditions and practices at active mines; c) examination of existing Federal regulations on explosive storage to determine whether they address all conceivable safety problems, whether they contain redundant or obsolete standards, and whether their intent is clearly stated; d) recommendation, for safety improvements and for revision and clarification (if necessity) of governmental regulations. Magazine explosions are rare. A recent increase in magazine explosion frequency must be attributed to a large increase in deliberate (criminal or malicious mischief) explosions. Fires of various origins account for the remaining explosions of the past decade. During 1884-1926 several lightning-generated explosions occurred in non-metal magazines, but none recently. It appears that the contents of a well-constructed, metal magazine are immune to direct lightning strikes, regardless of whether the magazine is grounded or not grounded. Grounding a metal magazine cannot be harmful, but it may well be superfluous. Magazines were observed at 34 widely separated mines and storage problems were discussed with personnel at these mines. In general, storage conditions and practices were found to be satisfactory. Usually, only small quantities of explosives are stored on mine property since most explosives are brought in by suppliers when needed. MSHA and BATF standards on explosive storage appear to cover safety aspects adequately. However, certain revisions are recommended to clarify some of these standards and to reduce inconsistencies in their enforcement.

Jan 1, 1983

By A. Feather

Avmin have developed a flowsheet for the refining of copper, nickel and cobalt from Nkomati concentrates. Cobalt is recovered from calcium-saturated solution using Cyanex® 272. Nickel is subsequently extracted using versatic acid. The loaded organic is stripped using spent electrolyte, producing advance electrolyte for recovery of nickel by electrowinning. Cobalt was recovered with >99.5% extraction efficiency, reducing cobalt from 1.8 g/l to <10 mg/l. The cobalt/nickel ratio in the cobalt product solution was >1500. Nickel solvent extraction was optimized to recover 99%, reducing the nickel concentration from 32 g/l to <0.3 g/l, while minimizing calcium deportment to the nickel electrowinning circuit.

Jan 1, 2002