Search Documents

By H. H. Fields

The Bureau of Mines is in the process of degasifying a virgin area in northern West Virginia from the base of an 839-foot-deep vertical borehole¬. An in situ gas pressure hole 199 feet long, and seven degasification holes ranging in depth from 500 to 850 feet (average 618 feet) were drilled in an 8-foot-thick virgin Pittsburgh coalbed from the enlarged (14-foot-diameter) bottom of this borehole. The in situ pressure at the back end of the hole and the range of gas and water flows from degasification holes as they were completed and closed off were 203 psi, 79,000 to 257,000 cfd (average 160,000 cfd), and 5 to 8 gpm per hole (average 6.8 gpm), respectively. Twenty-four hours after the seven holes were connected through individual water traps to a common collector for natural venting of the gas through pipes to the atmos¬phere, the total gas and water flows and the in situ pressure dropped, respec¬tively, to 971,000 cfd, 1.3 gpm, and 18 psi. Eighty days later the correspond¬ing values dropped to 529,000 cfd, 0.50 gpm, and 13 psi. After 180 days of degasification, 91 million cubic feet of gas had been removed from the affected virgin area. This represents 60 to 70 percent of the gas calculated to be contained in the area of coal affected by the holes.

Jan 1, 1973

By M. Dattilo

The U.S. Bureau of Mines has been conducting research on the use of waste-derived zinc as a partial replacement for pure zinc in the electrogalvanizing process. The end product of this process is automotive sheet, which has enhanced cosmetic protection over previously used cold-rolled (CR) steel. In this study, primer-coated specimens of CR and electrogalvanized (EG) steel were subjected to the on-vehicle environment and monitored periodically by electrochemical impedance spectroscopy (EIS) during immersion in 1M NaCI solution. The results of these tests were compared with immersion-only conditions. Scanning electron microscope (SEM) and energy-dispersive X-ray (EDX) techniques were also used to evaluate the corrosion processes and compare them with atmospheric exposure specimens. EIS was found to measure the corrosion associated with on-vehicle exposure, thus providing an excellent screening technique for evaluation of the performance of EG automotive sheet steel.

Jan 1, 1990

"The Antamina orebody is a geologically complex, polymetallic skarn located in the Peruvian Andes. A range of copper and copperzinc ores are campaigned separately through the concentrator producing copper and zinc concentrates as well as lead and molybdenum by-products.Ore type classification at Antamina is based on chemical assays; geological or lithological variations are not considered. Consequently, each ore type demonstrates a wide range of concentrator performance.Antamina is currently implementing a system to track ore movements from the shovel face to the concentrator. Relatively sophisticated models of run-of-mine and coarse ore stockpiles ahead of the mill will be used to account for the variable delay between mining and milling.One of the numerous benefits of ore tracking is the ability to directly associate the measured concentrator performance with a physical location in the orebody. Using existing mine planning software, three-dimensional models can be created of such performance measures as metal recovery, concentrate quality, operating cost, and reagent consumption.Such a database of information allows the true value of different ore sources to be determined. The value of an ore source is conventionally measured as metal content (individual or combined ‘equivalent’) with a cut-off grade applied to indicate some base level operating cost. However, the true value of an ore source should include dynamic factors like haulage cost, reagent use, smelter penalties, and even prevailing metal prices. If an ore source is considered from all perspectives rather than simply its potential to deliver value, the concept of ore becomes more flexible. Any ore source that reveals itself to be unprofitable can be eliminated from the mine plan or possibly blended with others to improve its value. The ability to predict mill performance, and thereby profitability, is a powerful tool.In an operation such as Antamina, where managing ore sources, campaigns, and the delivery of a variety of concentrates in a narrow timeline to customers is a daily challenge, prediction is the key to success and improved efficiency."

Jan 1, 2005

In blasting large tonnages of ore or material, the economy of the operation 'depends mainly on the mine manager's judgment in placing the holes to the best possible advantage and in determining the most effective size of hole to suit the conditions and requirements.The placing of holes is often looked upon as a problem involving so many uncertain factors that the application of simple mathematics is impossible. The uncertain factors arise when dealing with strata of different character, in hardness toughness and resistance to shearing.A study of the practice at many mines where all types of strata from hard ore to relatively soft overburden, and even coal, is being mined, suggests that the problem is not as complex as generally believed. There is, without doubt, some uniformity in the amount of burden given to holes of equivalent dimensions, regardless of the material being mined. The reason is simple. With too great a burden hard rock will not break out and soft rock will "bull". The nature of the strata is taken care of by the strength, quantity and distribution of the explosive charge and, to some extent, the spacing of the holes.It is because burdens are uniform in all classes of strata met with in mining, that a formula can be used to design blast hole layouts.The formula introduced in this paper is empirical as it is based on prevailing practice. It has been tested and proved remarkably accurate against every example available to the writer. Many thousands of blast holes, at many different mines, are represented by the examples given in the attached tables; to give further examples would only mean, unnecessary repetition. At the Mount Morgan Mine...

Jan 1, 1952

By Z. Lin, M. Isac, R. I. L. Guthrie

The kinetic and thermodynamic efficiencies of chromium recovery from the slag in an AOD process during the slag de-oxidation period with ferrosilicon is a complex process affected by slag basicity, temperature, the dissolution kinetics of the reducing agents, and intermixing of the slag/metal/alloy addition phases within the vessel. The present work focused on a study and simulation of the fluid dynamics and mixing behaviour of ferrosilicon additions in the AOD process for the production of stainless steel. In order to visualize the mixing behaviour, a two dimensional slice model of an AOD vessel was first built and filled with ZnCl2solution and then covered with silicone oil in order to represent the bulk liquid steel and slag phases, respectively. The injection of argon/oxygen process gases was simulated using air or helium. Particle trajectories and intermixing of the phases was monitored with a high-speed camera. To simulate the 75FeSi additions, glass spheres were used. A three-dimensional version of the AOD model was then constructed in order to confirm the adequacy of the slice model. Similar particle mixing behaviour was observed. Both models demonstrated that the ascending gas/liquid plume created two asymmetric mixing zones: a smaller rapidly re-circulating mixing zone adjacent to the side-wall locating the tuyere(s), and a larger mixing zone in the main part of the vessel. The process efficiency during the reduction period is governed by the thermal behaviour of ferroalloy as well as the mixing efficiency in the main large mixing zone. To enhance the recovery efficiency for chromium, small Fe-Si particles are suggested, given their wide distribution within the slag phase, and their large interfacial areas and rapid melting times for Cr2O3reduction from the slag. Keywords; modelling, ferrosilicon, chromium oxidation, AOD steelmaking.

Jan 1, 2004

By G. B. Bell

"INTRODUCTION On February 1, 1962, after five years of exploration and research, Jones & Laughlin Steel Corporation announced that they would develop the Adams Mine. Plant construction began immediately and in December of 1964 the first shipment of pellets arrived at J & L's blast furnaces in Pittsburgh. J & L continued to operate the property through its wholly owned subsidiary, Jones & Laughlin Mining Company, Ltd., until August of 1971 when it was sold to Dominion Foundries and Steel, Limited of Hamilton. Dofasco engaged Cliffs of Canada, a subsidiary of Cleveland Cliffs Iron Company, to manage the operation of the property.SUMMARY:The Adams Mine is a one million tons per year iron ore pellet operation located in the Boston Township Iron Range, approximately seven miles southeast of Kirkland Lake, Ontario. The property includes 5,300 acres in which eight areas suitable for open pit mining have been outlined. It was estimated that the reserves in these out lined areas are sufficient to produce 30 million tons of high grade iron ore pellets.The ore 'consists of fine grained magnetite with alternating layers of chert and is mined by conventional open pit methods. This extremely hard and abrasive ore averages about 20 percent magnetic iron, and has a ratio of concentration of 3. 9 /1. Presently, mining operations are confined to two pits with a third one being developed for operations to begin in 1973.The run-of-mine ore is crushed and ground and then concentrated by magnetic separation and flotation to a concentrate grade of 68 percent magnetic iron. The concentrate is agglomerated by a grate-kiln pelletizing process and shipped by rail to Dofasco's blast furnaces in Hamilton and to Jones & Laughlin's furnaces in Pittsburgh."

Jan 1, 1973

By J. Dionne

"Next to the actual mine of Les Explorations Muscocho Ltée in Montauban, Quebéc, you could find a total of 364 000 tons of flotation tailings assaying 1.4 Au g/t et 82 g Ag/t to the south of the municipality. This tailings pile is what is left of previous operations. Preliminary leaching tests on these tailings in laboratory columns gave interesting results which led to tests in larger columns in 1984 and to a pilot test on a 750 ton heap in Montauban during the summer of 1985.This paper briefly describes the columns tests performed at the Centre de Recherches minérales and the heap leaching test designed and conducted by SOQUEM in Montauban. It also presents the results obtained.RESUMEPrès de la mine actuelle de Les Explorations Muscocho Ltée à Montauban, Quebéc, se trouvent, au pied du village, 364 000 tonnes de rejets de flottation titrant environ 1,4 g Au/t et 82 g Ag/t. Ce tonnage de rejets représente ce qui reste de l'opération des anciennes mines de Montauban.Des essais préliminaires de lixiviation en colonne sur ces rejets ont donné des résultats encourageants. Ils ont été suivis en 1984 par des essais en colonnes plus volumineuses et par un essai pilote à Montauban en 1985 sur une pile de rejets de 750 tonnes.Ce te x te donne une brève de script ion des essais en colonne effectues au Centre de Recherches minérales et de l’essai pilote planifie et exécute à Montauban par SOQUEM. Il présente les résultats obtenus."

Jan 1, 1987

A physical modelling study has been carried out to simulate the slag-metal dispersion induced by a high-strength bottom gas injection. Water and kerosene were utilized to simulate metal and slag respectively. A water model of CLU (Creusot-Loire Uddeholm) vessel was used with three different nozzle orientations, namely, off-centre, triangular off-centre and centre. The gas flow rates changed from 0.00599m3/sec to 0.01081m3/sec. Height of heavy and light phases was kept fixed at 0.23 m and 0.02 m respectively. The dispersed phase holdup was determined at various axial and radial distances, gas flow rates, and tuyere configurations. The observations revealed that at a fixed gas injection rate, as the vertical distance increased in the centerline, straight off-centre orientation resulted in greater dispersed phase hold up values than those of the centre configuration and the triangular off-centre orientation. The dispersed phase holdup was found to increase with gas injection rate and decreased with axial distance. The variation of the dispersed phase hold up with the dimensionless axial distance and the gas injection rate was correlated by using the Modified Froude Number. The experimental values of the dispersed phase holdup were found to be in good agreement with the correlated values obtained from the modelling equations. The findings of the present study may be utilized in the ferroalloy refining vessels in terms of designing tuyere locations for optimum processing conditions.

Jan 1, 2004

By Derek J. Penrice

A critical element of the Transbay Transit Center Program, the Caltrain Downtown Extension (DTX) will extend commuter rail service into downtown San Francisco and accommodate future statewide high-speed rail service. The DTX project includes 1.8 miles of underground construction, comprising significant sections of mined and cut-and-cover tunnel. At the request of stakeholders, an updated cost estimate was prepared early in the project?s preliminary engineering phase. Unsurprisingly, this yielded a cost substantially higher than the available budget. This paper provides a summary of the management processes and planning decisions taken to bring the project back to budget, resulting in a configuration which derives maximum value from available funding and retains maximum flexibility for future system expansion.

Jan 1, 2008

Case 1: A driller raised a drill rig mast into a 7200-volt overhead power line. Both he and his helper were killed. Case 2: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ]

Jan 1, 2006

The Pike River Coal Company is set to develop the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine will be developed to extract a coking coal deposit of the Brunner Seam, some 46 km north-east of Greymouth, using a combination of continuous miners and hydraulic extraction.   The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park. As such, the major restriction to planned extraction is protection of:   +        the western escarpment, +        vertical and sub-vertical rock faces, +        permanent water courses, +        significant vegetation, and +        steep slopes.   The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumps down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.

Jan 1, 2005

By Laurance L. Oden, Jack C. White, Alan D. Hartman

The U.S. Bureau of Mines, under a Memorandum of Agreement with the American Society of Mechanical Engineers (ASME), established design criteria for a facility to field residues from municipal waste combustion. This facility, which is available to potential users on a cost-sharing basis, is also applicable to a variety of inorganic waste materials from smelting or melting operations. The design consists of a mechanical feed handling system, electric arc melting furnace, fume-off gas handling system, and thermal oxidizer for final off gas treatment. Screw conveyors and a bucket elevator deliver up to 2,000 Ib/h of minus I-in material to a three-phase electric arc melting furnace. This unique 800-kVe A furnace has a water-cooled shell and roof to minimize interaction of the melt with the refractory lining. The volume of the hearth below the slag taphole is approximately 1.2 st of steel. The furnace is sealed, allowing atmosphere control within the furnace and fume duct by nitrogen or inert gas injection. A jet-pulsed baghouse removes particulate from the off gas and serves as an acid gas scrubber. The clean off gas is heated to 1,800' F for 1 s in a propane-fired thermal oxidizer before being vented to the atmosphere.

Jan 1, 1993

By M. D. Khattar

Problems discussed concern encountering of high temperatures [up to 66°C] and heavy flow of water [150 L.P.S] during the construction of the 10.15 MØH.R.T. for the 2500 MW Nathpa Jhakri Hydro Power Project in the Himalayas(India). Over a length of 2500 M progress of work got seriously affected resulting in excessive time for completion - two years [max. monthly progress achieved was 178 M [Heading]. Many innovative and simple steps were taken to complete the work in these inhospitable environs affecting working of both men and machines. Also it meant a review of the design of concrete lining. Other geological conditions affecting the progress are also described.

Jan 1, 1999

By M. R. Geer, H. F. Yancey

"INTRODUCTION With the advent of war in 1941, military operations in Alaska were enlarged on such a scale that the demand for coal in the Territory more than doubled. Coal was needed urgently for heating forts and other military establishments, for use on large construction projects, and for handling the greatly increased volume of traffic on the Alaska Railroad. -The additional tonnage required, estimated at perhaps 250,000 tons per year, probably could have been supplied by the United States, but shipping space between Pacific Coast ports and Alaska was already overburdened with military supplies and construction materials. Moreover, although of only secondary importance in wartime, the cost of coal shipped into the Territory is reported to have been as high as $40 per ton. The alternative to importing coal was, of course, to increase the Production of the Alaska mines.Production of coal in Alaska reached, 350,000 tons in 1944, or more than double the prewar' output. The responsibility for increasing coal production was assumed largely by the Army, A Coal Commission attached to the Alaska Department arranged financial assistance for some mining operations, aided the operators in producing equipment for mechanization, and provided most of the labor necessary to operate the mines. The Bureau of Mines contributed to the program in several ways. First, exploration by the Bureau in the Moose Creek district revealed a substantial tonnage of coal of better grade than any currently mined in the Territory, 4/ and drilling in the Broad Pass district, where a mine to supply coal for the army had been started, revealed that the reserves were far less than had been supposed; this operation was abandoned. Second, coal-preparation practices were studied, and recommendations for improvements made, at two of the operating mines at which the quality of the coal makes preparation a factor of vital importance. Some of the information obtained in these studies forms the basis for the present report."

Jan 1, 1946

By W. I. Nissen

This Bureau of Mines report presents the design for a commercial-sized flue gas desulfurization (FGD) demonstration plant that uses the citrate process. The goal of the Bureau's citrate process is to minimize the undesirable environmental impacts of industrial plants emitting SO2-bearing gas. The FGD plant is located at the George F. Weaton powerplant, Monaca, Pa. Construction was completed in April 1979 and will be followed by preliminary testing and a 1-year testing and evaluation program. Design capacity of the FGD plant is 156,000 scfm of 0.2-volume-percent-SO2 flue gas yielding about 16 tons of sulfur per day. The plant is intended to (1) clean fly ash, SO2, and Cl- from the gas while cooling the gas in a venturi scrubber, (2) absorb SO2 from the gas using 1,200 gpm of a countercurrent-flowing citric acid-sodium citrate-sodium thiosulfate solution, (3) react the absorbed SO2 in two 13,000-gal stirred closed vessels with added H2S, thus precipitating elemental sulfur and regenerating the citrate solution for recycle, and (4) recover the sulfur from the slurry by air flotation, followed by melting in a heat exchanger and separation from the occluded citrate solution in a sulfur decanter at 35 psi and 135° C.

Jan 1, 1979

By D. B. Stewart

In the past few years, much effort has been spent in elucidating the impact of diesel engines on the mine environment. This paper summarizes diesel fundamentals , exhaust emissions and typical tailpipe concentrations. Mine sampling results and an evaluation of exhaust treatment systems are discussed. A review of changes in pollutant concentrations between the tailpipe and the mine exit is made and suggestions are given to reduce operator exposure to diesel contaminants.

Jan 1, 1978

Peñasquito is Mexico's largest gold producer, consisting of two open pits - Peñasco and Chile Colorado - containing gold, silver, lead and zinc. Over the next three years, mining activities in the pit are expected to be focused on lower grade ore in the upper parts of the Peñasco pit while stripping is emphasized to ensure an economically optimal pit shell design to maximize the net asset value of the operation. By 2019, Peñasquito’s gold production is expected to benefit from an improvement in mined grades as it recommences mining higher grades at the bottom of the Peñasco pit and significantly enhanced metallurgical recoveries with the planned completion of the Pyrite Leach Project ("PLP").

Jan 1, 2017

By Félix Lewandowsky

El presente trabajo señala el proceso de cierre desarrollado durante el año 2000 en la mina Julcani. Las etapas de cierre comprenden el procedimiento de diseño, ejecución y control-seguimiento y como tal, contienen un sistema de seguridad (SHEB) en las operaciones de la mina. El principal objetivo del proceso de cierre es la estabilización a largo plazo del entorno físico, químico y socioeconómico en las áreas afectadas por la actividad minera para asi proteger la salud, el ecosistema y reducir los efectos negativos en el ecosistema. Finalmente, es más factible ejecutar el plan de cierre durante la operación de la mina que cuando no es económicamente viable.

Sep 13, 2001

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

By P. A. Riveros, W. D. Gould, R. Molnar, D. W. Koren, P. Bédard

This paper reports the results of the field demonstration campaign of a new process for removing and destroying ammonia from mining/ metallurgical effluent solutions. The 50-day campaign was carried out at a uranium plant in Saskatchewan, Canada. The process was developed by adapting and integrating two well established technologies: zeolite adsorption/ elution to extract the ammonia from the effluent stream and to produce a concentrated ammonia eluate; and conversion of the ammonia in the eluate to innocuous nitrogen by applying bacterial nitrification-denitrification (NH3 = > NO3 - => N2). The data show that reasonable target criteria were met, under very challenging operating conditions. Problem areas and possible causes for poor performance are identified. Preliminary and generic cost estimates of the process are also presented.

Jan 1, 2003