Search Documents

By R. Flood

"Oil has been discovered off Newfoundland in a number of locations on the Grand Banks, the most notable and exciting being in 1979 when Hibernia was discovered. This discovery has brought new challenges to the province as well as to all of Canada. During the seven years"" since its discovery, both industry and governments have attempted to define its parameters and to find the most efficient and economical way to develop the field.A number of studies have been completed during the interval and in 1985, Mobil Canada Ltd. and partners stated that they would prefer to develop the field by using a concrete Gravity-Based Structure (GBS). IntroductionHibernia is located in an environmental climate much more severe than that of any previously developed oil field. The wind and wave conditions are similar to those of the North Sea, but unlike the North Sea, any structure on the Grand Banks would have to contend with ice floes and icebergs. Decisions had to be made on whether fixed structures could be put in place that would withstand the pressures of the ice and the impact of an iceberg, or whether structures that could be removed when such impacts were imminent would be used.Early studies in 1981, determined that it was possible to build a concrete Gravity-Based Structure which could withstand the impact of the largest icebergs that are anticipated to float in that area of the banks.Additional studies increased the knowledge of icebergs: their patterns and size, and verified the original conclusions that Concrete Gravity-Based platforms would provide a practical solution."

Jan 1, 1988

By E. B. Olds

This paper describes the methods and costs of deepening the 3-compartment underground shaft in the Hooper Tunnel adit at the Bunker Hill & Sullivan Mining and Concentrating Company Crescent mine in the Coeur d'Alene mining region, 7 miles east of Kellogg, Shoshone County, Idaho. The work was done with the aid of a Defense Minerals Exploration Administration contract (No. Idm-E493, Docket No. DMEA-2764). Preparation for deepening the shaft was begun March 26, 1953, and sinking was completed May 27, 1954. The shaft, bottomed at 1,275.5 feet in 1939, was deepened to 3,276 feet, using mechanical mucking and intermediate pockets. A total of 50,349 man-hours was required to complete the work of sinking 2,000.5 feet, cutting 7 pump stations, and driving 2 pocket raises. The rate of advance was 7.1 feet of shaft per operating day, or 8.4 feet per day of actual sinking. The total direct cost for sinking was $205.20 per foot.

Jan 1, 1957

By Güven Önal, Gülay Bulut, Mustafa Özer, Yunus Emre Benkli, Olgaç Kangal, Mustafa Tarkan

There are various types of natural zeolite deposits in Turkey. Naturally occurring zeolites are excluded from many important commercial applications where uniformity and purity are essential. In this paper, the beneficiation of natural zeolite, taken from western part of Turkey, was investigated. According to X-Ray Diffraction (XRD) and mineralogical studies carried out on the representative ore sample, the natural zeolite was found to be in the forms of clinoptilolite and heulandite. Clinoptilolite forms as a devitrification product of volcanic glass in tuffs. Quartz, clay minerals, orthoclase, plagioclase, biotite, seruzite-muskovite and epidote were observed as impurities. Several types of mineral processing methods were performed in order to remove impurities from the natural zeolite sample to produce high purity zeolite. Gravity separation methods such as shaking table and superpanner were carried out for separating heavy minerals, while high intensity dry magnetic separation was used for discarding magnetic minerals.

Jan 1, 2003

Executive.. CHARLES F. RAND, Chairman. JAMES F. KEMP, JOSEPH W. RICHARDS. ALBERT R. LEDOUX, BENJAMIN B. THAYER. Membership. BENJAMIN B. THAYER, Chairman. WALTER R. INGALLS, JOHN H. JANEWAY, Jr., JOHN D. IRVING, HERMAN A. PROSSER. Finance. EDWARD L, YOUNG, Chairman. KARL EILERS, JAMES GAYLEY. Library. JAMES F. KEMP, Chairman. JOHN HAYS HAMMOND,3 E. GYBBON SPILSBURY,2 ALES. C. HUMPHREYS 4 BRADLEY STOUGHTON.

Jan 7, 1913

By D. E. M. Plaumann

"The wet grinding of asbestos has attracted the attention of engineers for many years as a means of improving fibre liberation from the ore. Today, added impetus for wet grinding has resulted from a need to minimize worker exposure to asbestos dust in conventional dry mills using air, as well as a need to provide a cleaner, technically superior fibre for use by product manufacturers. However , high viscosities of asbestos slurries create transport and grinding difficulties which have been a factor impeding use of a wet grinding process.Laboratory evaluation of reagents to reduce viscosities of asbestos slurries found that one reagent, XFS-4272.00, reduced the viscosity of a 35% (by weight) slurry by 75%. The impact of XFS-4272.00 on actual grinding parameters were evaluated using a pilot plant rod mill. Slurries containing 78% solids and XFS-4272.00 were successfully milled and asbestos fibres from that milling compared favourably in liberation and relative surface area to asbestos fibres obtained from milling a 4% slurry without additives.IntroductionAlthough the use of asbestos has been declining over the last few years, the large deposits of chrysotile in eastern Canada (Quebec in particular) remain very important. Asbestos production in Canada stands ninth in volume for mineral production with over 740 000 tonnes produced in 1985. Of this quantity, 722000 tonnes were exported with a value of $446 million . Canada is second in world production of asbestos behind the U.S.S.R ."

Jan 1, 1988

By F. F. Sharpless

ON Saturday evening, Sept. 9, a small party of Institute members, their wives and friends, left New York to attend the Fall Meeting of the Institute at San Francisco. In this party there were: President and Mrs. Arthur S. Dwight; Mr. and Mrs. George D. Barron; Mr. and Mrs. H. J. Stehli; N. S. Spencer and Miss Spencer; the Secretary and Mrs. F. F. Sharpless. They were joined at Chicago by E. F. Eurich, and by Mr. and Mrs. R. L. Baldwin and daughter. Our party was met at Chicago by Mr. and Mrs. L. V. Rice, Mr. and Mrs. A. D. Terrell and W. F. Boericke, who constituted themselves an impromptu entertainment committee and proceeded to carry out a delightful little program. We were taken to the Lake Shore drive, where a stiff wind off the lake refreshed us after a sultry day on the train, and on our return to the city saw Chicago illuminated with all its brilliance of electricity. We were entertained at dinner at the Drake Hotel. In spite of being two hours late getting into Omaha, we were right on the dot at Denver on Tuesday morn-ing. Horace F. Lunt came to the hotel soon after breakfast, and told us that a trip to the mountains had been planned. Having learned the number in the party, he began to gather up his automobiles for a 10 o'clock start.

Jan 10, 1922

By Charles Barrett

SINCE 1925, when the preferred orientations in compressed aluminum were first determined1, 2 the orientations have been described as a fiber texture in which a face diagonal, [110], of the face-centered cubic lattice is parallel to the compression axis. Subsequent experiments have seemed to confirm this texture,3-5 and a number of theories (recently summarized in references 6 and 7) have been proposed to explain it and to relate it to the behavior of single crystals during compression. 3,8-11 The experiments reported in this paper prove that the orientations are not adequately described as quoted above-i.e., as a [110] fiber texture-although this is a first approximation to the actual texture. They also show that the texture cannot be thought of as a stable orienta-tion that is reached and maintained after a sufficient amount of deforma-tion. The actual texture, when studied in detail at successive stages of compression, indicates that a hitherto unsuspected range of orientations is present, both in the polycrystalline metal as a whole and in various individual grains in its interior, and that a state of dynamic equilibrium exists within this range. The reasons for the failure of previous theories to predict the actual texture become obvious when the heterogeneous nature of the flow is considered. In addition to the deformation texture, the manner of its develop-ment, and its theory, this paper presents data on the following related subjects: the identity of strain markings in aluminum; the orientation changes in aluminum single crystals during compression and a com-parison of these with the conditions in individual grains of a polycrystal-line specimen; the origin of asterism in deformed single crystals, which heretofore has been regarded as a distortion localized at the surfaces of slip planes; and the relation of plastic strain in individual grains in an aggregate to the strain of the whole.

Jan 1, 1939

By F. K. Crundwell

The rate of dissolution of sulphide minerals is frequently interpreted in terms of the passivating behaviour of a layer of material on the surface. This interpretation has driven research to identify and possibly remove this layer from the surface, and thus yield higher rates of dissolution. The identification of such layers has proved difficult, with different researchers claiming different compositions for possible layers. An alternative framework has been pursued by the author and co-workers, who have argued that the rate of dissolution is governed by the electronic structure of the minerals which give rise to their semiconducting properties. Researchers sceptical of this approach have argued that semiconducting properties are only important in highly pure substances. In this paper, we review the electronic and semiconducting properties and discuss how they impact dissolution behaviour. These properties affect their colour and dissolution properties even though the minerals are not high purity substances. Keywords: Dissolution, leaching, passivation, semiconductor, chalcopyrite

Jan 1, 2020

By Izabelle Lannes Salgueiro Ferreira

O presente trabalho tem o objetivo de mostrar como sistemas especialistas melhoram a gestão da qualidade e processos ao trabalhar com grandes massas de dados, que são gerados continuamente pelos processos produtivos de laminação a quente.

Aug 17, 2017

By Luis Alvarez

La productividad de las operaciones mineras está directamente asociada a la optimización de los recursos humanos y de los equipos, por tal motivo se propone la aplicación de un sistema que permite monitorear en tiempo real a los operadores de los equipos mediante el uso de aplicaciones de realidad aumentada, añadiendo información virtual a la información física ya existente.

Sep 1, 2017

By Rodrigo Sales

Os principais objetivos de um projeto de Integração e Otimização de Processos (PIO – Process Integration and Optimisation) é de auxiliar no desenvolvimento de uma estratégia integrada de desmonte e cominuição que minimize o custo total por tonelada processada nas etapas de lavra e cominuição das operações, minimize o consumo de energia e maximize a taxa de processamento, produção de metais e lucro da empresa. O projeto consiste na revisão de práticas operacionais, auditoria e amostragem, benchmarking, modelagem e simulações das operações de perfuração e desmonte e cominuição. Isto permite uma análise holística das operações para identificar oportunidades de melhorias e desenvolver estratégias integradas e otimizadas de operação da mina-à-planta. O projeto incluiu o sistema exclusivo da Metso, SmartTag™, para rastrear o minério dos furos de desmonte na mina até a planta concentradora com o objetivo de correlacionar os tipos de minério e de desmonte com os resultados de desempenho da planta. O sistema de modelamento geometalúrgico automatizado chamado GeoMetso™ utiliza a tecnologia de rastreamento de minério SmartTag™ para coletar continuamente dados de desempenho da planta e atualizar automaticamente os modelos preditivos e o modelo de blocos em tempo real. Este sistema é a base para a implementação, validação e melhoria contínua das estratégias integradas e otimizadas de operação, além de auxiliar na reconciliação da mina-à-planta e planejamento de lavra.

Aug 17, 2017

By P. Hanniala, S. Harkki, B. Andersson

"The Outokumpu Flash Smelting Process was put into commercial operation in 1949. The original process was based on the use of preheated air. The adoption of oxygen enrichment of the flash smelting process air in 1971 was a crucial improvement, especially for smelter capacity. Oxygen use according to the Outokumpu method means selection of the most suitable oxygen content for the process air on the basis of the concentrate composition, capacity and matte grade. The furnace is not bound to only one fixed degree of process air oxygen enrichment; the oxygen content may vary from 21% to 100%.The degree of oxygen enrichment and the matte grade are the most important process parameters in reducing the operating costs of the whole system, including smelting, converting and acid production. Raising the matte grade allows more efficient use of the reaction heat in the smelting stage. Sulphur is recovered in a high-strength, constant-flow gas stream. The blowing time in the converters is reduced considerably.Oxygen enrichment and high matte grade improve the energy efficiency of the plant complex as long as the surplus heat from the system is not wasted. When the operating costs and investment expenditure of the total plant complex are taken into account, a reasonably high degree of oxygen enrichment (35-80°/0) is the best alternative in practice. Existing operating smelters have achieved single-stream thoughputs of over one million t/yr of concentrates.HistoryLocal capital and operating costs as well as lower energy consumption per unit of metal produced are now the crucial factors in determining the choice of process. In the late I940s, the same reasons prompted Outokumpu to develop the original flash smelting process in Finland. Between 1900 and 1940, very few technical changes in pyrometallurgical copper production took place. However, the commercial use of the flash smelting technique began a new era in metal extraction from sulphide concentrates. The characteristic feature of the method is that the concentrate is smelted in suspension: this offers the most favourable conditions for heat and mass transfer, and thus high reaction velocities. Outokumpu was the first to exploit the known advantages of flash smelting in a commercial installation at Harjavalta in 1949."

Jan 1, 1982

By Ana Luiza Chaves de Oliveira

Com o avanço do conceito de sustentabilidade e as novas legislações ambientais, percebemos um crescente aumento da responsabilidade ambiental. As empresas cada vez mais investem em coletas seletivas, tratamento dos resíduos, etc., buscando minimizar os impactos ambientais, preservar os recursos naturais e assegurar a sustentabilidade. Tendo como objetivo apresentar uma solução integrada para a reciclagem e reaproveitamento dos resíduos refratários após o uso. Este trabalho propôs a produção de três classes de argamassas secas e úmidas através da utilização de reciclados. Foram realizadas quatro etapas (identificação visual das matérias-primas, cominuição, formulação/produção e acompanhamento durante a estocagem). Procurando avaliar o potencial dos reciclados o acompanhamento será realizado através da variação reológica e da determinação da força ligante após a fabricação e durante a estocagem (período de 12 meses). Os resultados evidenciaram que há potencial de reaproveitamento dos reciclados tanto na produção de argamassas secas e quanto úmidas sem que ocorra perda de suas propriedades reológicas, químicas e termo-mecânicas.

Aug 17, 2017

By Hampshire MJ

The tailing retreatment project rated at 10 000 t/day commenced operations in October 1982. The operation consists of dredging, feed preparation, cyanide leaching and carbon-in-pulp (CIP) gold recovery followed by Zadra atmospheric stripping and electrowinning. For the first two years the operation was adversely affected by excessive cyanide consumption and low gold extraction. Investigations demonstrated that the very fine, or slime, fraction of the tailing was the dominant consumer of cyanide and dissolved oxygen. The plant flowsheet was subsequently modified by inclusion of 80 - 100 mm dia. cyclones for slimes separation and a 31 m dia. thickener for water recovery. Treatment of deslimed feed in the CIP plant has reduced sodium cyanide consumption from an average 1.85 kg/t to 1.15 kg/t. The reduced oxygen consumption by the CIP plant feed has resulted in higher dissolved oxygen levels, frequently reaching supersaturation after 4 to 5 h contact time. This has allowed much improved gold extraction from the existing CIP plant capacity. Gold extraction from the mixed pyritic siliceous tailing has improved from an average U prior to desliming to a current 57%. Investigations are continuing on the recovery of gold from the discarded slimes.

Jan 1, 1986

By E. Arioglu

Y. Luo and S.S. Peng are to be congratulated for their outstanding paper providing new results from surface subsidence monitoring over longwall panels under different conditions. This writer found the authors' paper very interesting. In reference to this paper, the following contributions are offered: • In the paper, the maximum possible subsidence (?Smax) induced by chain pillar convergence has been related to a parameter (h/I -p) by linear regression. (Notations are expressed in this discussion's Fig. I (b).) It is a well-known fact that in a goaf the roof lowers onto broken material that gradually compacts. Then the physical behavior of goaf may closely follow the compaction characteristics of broken materials. In light of this assumption, a mathematical means (Fig. 1(a)) of defining the expected compaction (i.e. surface subsidence) represents an exponential expression between ?Smax/m vs. h/1-p. This is based on Luo and Peng's field observations from the Appalachian, Illinois and Alabama coal fields. (The coefficient of regression "r" under consideration was computed to be 0.883). • According to Wardell's (1969) findings for board and pillar mining, the maximum possible subsidence can be expressed in terms of maximum pillar loading (depth, ratio of extraction) and the height-to-width ratio of the pillars left. Using Luo and Peng's 1991 results, this writer discovered a regression equation between the above-mentioned factors. As displayed in Fig. 1(b), the functional expression approximates as closely as possible the observed subsidence data.

Jan 1, 1992

Members whose deaths were reported from Apr 7, 1923, to Apr 5, 1924 Elected Died 1918 ADKINSON, HENRY M 1923 1900 AGNEW, WILLIAM C 1923 1894 ASHLEY, H H 1923 1897 AUSTIN, KENNETH 1924 1903 AYERS, EMMA L C 1923 1913 BAECHTOLD, CHARLES A 1924 1900 BAIN, HUGH A 1924 1919 BASHORE, E GORGAS 1923 1920 BATTELLE, GORDON 1923 1923 BAYLES, GERARD L 1924 1881 BROCK, CHARLES 1923 1903 BROOKE, HENRY 1923 1876 BROWN, HARVEY H 1923 1904 BROWN, THOMAS E 1923 1919 BUCK, DANIEL M 1924 1906 CHALMERS, THOMAS S 1924 1881 CLEMES, JOHN H 1923 1896 COLLINS, HENRY F 1924 1871 COURTIS, WILLIAM M 1923 1915 CRESSON, B F, JR 1923 1921 CROWE, WALDO P 1923 1920 DARNELL, J ORA 1923 1911 DAVIS, HENRY G 1924 1918 DAVIS, ROBERT S 1923 1916 DEANE, WILLARD A 1924 1901 DEMPSTER, WILLIAM 1924 1911 DEVEREUX, W B, JR 1923 1895 DICKENSON, F M 1924 1904 DRUM, FRANK G 1924 1875 DUDLEY, P H 1924 1916 EATON, ARTHUR 1923 1919 EATON,SHERMAN 1924 1911 GRIFFITH, WILLIAM 1924 1919 HILSDALE, PAUL 1923 1922 HODGES, I F 1923 1916 HOFIUS, MAX, T 1924 1914 HUGHES, HOWARD R 1924 1919 HUMMEL, CARL B 1923 1874 HUNT, ROBERT W 1923 1921 JONES, ERNEST EVANS 1923 1917 JOSLIN, CHARLES T 1923 1918 KASJENS, JACOB G 1923 1899 KIRKEGAARD, PETER 1924 1920 KLAUS, HARRY C 1923 1892 KNOERTZER, HENRI1924

Jan 1, 1923

By J. W. Dougherty

THE Hollinger gold mine is in the Porcupine mining division, District of Cochrane, in the northern part of the Province of Ontario. The adjacent town of Timmins, with a population of 25,119, lies 490 miles by railway north of the city of Toronto. GEOLOGY The property is situated on the northwest limb of a major syncline, which pitches northeast at approximately 50°. The principal rocks of the Hollinger area are of pre-Cambrian age and consist of altered, schistose, Keewatin lava flows intruded by stocks of schistose, quartz-feldspar porphyry generally assigned to the Algoman period. The structure of the Keewatin series is extremely complex as a result of close folding and some faulting. The schistosity, trending north 70° east and dipping steeply to the southeast, is most highly developed along a subsidiary anticline in which the major porphyry bodies occur. The ore bodies, which exhibit three principal structures, consist of quartz veins and associated pyritized wall rock. Some lodes are com-posed of en echelon veins, others exhibit a main quartz body with branch-ing stringers and a third consists of a single definite lead. Gold, in a coarse visible form, may be confined to quartz in some ore bodies but in others it is finely divided and is found not only in quartz but also asso-ciated with pyrite in the adjacent wall rock. In many veins the dis-tribution of gold is such that there are several ore sections, separated by areas of low-grade material, in the same vein although its physical appearance remains unchanged.

Jan 1, 1940

1. Reviews A concise world atlas of geology and mineral deposits, by D. R. Derry. London, Mining Journal Books, 1980. (Reviewer: B. C. Alberts) The geology of the Western Cordillera of northern Peru, by various authors. London, Institute of Geological Sciences, Overseas Memoir 5. (Reviewer: C. E. Feather) 2. New books Influence of diffusion coatings on the strenth of steel, by G. V. Karpenko, V. I. Pokhmurovskii, V. B. Dasilov, and V. S. Zamikhovskii, second revised and updated edition by A. Aladjem. Aedermannsdorf (Switzerland), Trans Tech Publications, 1979. 200 pp. Sw. Fr. 68.00. Mechanical and corrosion properties, by G. S. Ansell, P. Haasen, J. Weertman, D. J. Fisher, U. Gramberg, and F. W6hlbier (editors). Heat-resistant and refractory steels, by K. L. Lanskaya. Aedermannsdorf (Switzerland), Trans Tech Publications, 1979. 266 pp. Sw. Fr. 86.00. Hardening of metals, by P. Feltham (editor). Aedermannsdorf (Switzerland), Trans Tech Publications, 1980. 316 pp. Sw. Fr. 78.00. Precious metals The 6th International Precious Metals Conference will be held in Newport Beach, California, from 7th to 11th June, 1982. Strata mechanics A symposium on Strata Mechanics is to be held in Newcastle-upon-Tyne from 5th to 7th April, 1982. Over the past thirty years, mining of coal and stratified mineral deposits has become increasingly capital-intensive, and the level of investment demanded by modern methods has led to demands for improved assessment of their likely performance.

Jan 1, 1981

By Rodrigo Perito Cardoso

Low-temperature nitriding of stainless steels is applied to obtain wear resistant surfaces without losing its corrosion resistance. The treatment consists in introducing nitrogen into the steel surface avoiding chromium nitride precipitation. The corrosion resistance of martensitic stainless steels is expected to be improved if the treatment parameters are correctly selected. It can be related to ?Fe2-3N and a'N phase formation on the treated surface. In the present work the influence of the pretreatment and treatment temperature on corrosion resistance of plasma nitrided AISI 420 steel samples is studied. Annealed, as-quenched and 400ºC-tempered samples were nitrided at 300, 350, 400, 450 and 500°C, for 6 h at 600 V. The pressure was 3 Torr and the gas mixture was composed of 70%N2, 20%H2 and 10%Ar, at a gas flow rate of 3.34×106 Nm3s-1. Plasma was generated using a square-wave pulsed DC power supply and the sample temperature was controlled by the duty cycle. The modified layers were characterized by optical microscopy, X-ray diffraction and microhardness measurement. The corrosion resistance was studied by electrochemical characterization, by means of Open circuit potential and Anodic polarization curves. The maximum surface hardness was achieved at 400°C. This temperature seems to be near the limit temperature for low-temperature treatment aiming to improve or at least to keep unaltered the corrosion resistance in relation to that verified for non-treated steel samples. Results confirm that the pretreatment and treatment temperature significantly affects the corrosion resistance of the treated surface.

Aug 8, 2018

By B Olsson, C Glassock

Computer simulation modelling (discrete event) has been used at Olympic Dam (OD) to model the handling of ore from the point of extraction at the stope drawpoint through to the ore stockpile on the surface. Computer simulation is a well accepted tool for modelling the behaviour of such large and complex operating systems. It is a particularly useful technique in complex operations where there are multiple interactions between the inputs and outputs of various unit operations. In this instance it can be utilised during the early stages of a project, for example, as part of the business case definition phase or the early engineering phase. A well constructed and tested simulation model provides a sound base upon which informed business decisions can be made. Furthermore, the behaviour of the model with varying inputs can help build a solid understanding of how the asset behaves when varying inputs and constraints are imposed upon it and, as a result, the major points of leverage that designers and operations personnel have to affect the real world behaviour of those assets. Better decisions can be made when the right facts can be examined, various options explored and conclusions tested. Simulation modelling is one of the tools available to make this process work.

Jan 1, 2005