Search Documents

By K. Hardy

As part of Inco's $115 million Fluid Bed Roaster SO2 Abatement Project, a new weak acid treatment plant (WATP) was constructed to treat bleed solutions from the Copper Cliff Smelting Complex gas-cleaning circuits. The WATP produces an iron-arsenic co-precipitate, termed "basic ferric arsenate" (BFA), which requires disposal in an environmentally acceptable manner. Following analysis of many potential options, the short-listed disposal alternatives were: A) Co-disposal of the BFA?gypsum sludge with rock tailings, a portion of which would be used in mine backfill, with the remainder being sent to the tailings area, and B) Co-disposal of BFA?gypsum sludge with pyrrhotite tailings in the tailings area. Testwork showed that the addition of BFA?gypsum sludge to mine backfill samples increased the uniaxial compressive strength (UCS) of the backfill for most samples, especially those at lower binder content ratios. Extensive analysis was conducted on samples taken from the Copper Cliff tailings area, where BFA?gypsum sludge from Inco's Copper Refining Electrowinning Department has been co-deposited with pyrrhotite tailings since 1990. Pore water samples from these areas contained very low arsenic concentrations, indicating that the arsenic had remained stable in that environment. Ultimately, co-deposition with pyrrhotite tailings was chosen as the preferred option for the disposal of BFA?gypsum sludge from Inco's new WATP.

Jan 1, 2006

By Chas. F. Jackson

During the past 5 years the Bureau of Mines has published information circulars dealing with mining methods and costs at 78 ore mines; 7 circulars, each of which is devoted to a discussion of one of the principal mining, methods; and 23 circulars dealing with special phases of mining, such as ventilation, shaft sinking, tunnel driving, the cost of equipping and developing prospects and small mines, underground transportation, diamond drilling, and ground support. These circulars were written by many different authors, and in order that the method of presentation and the basis for compilation of data might be the same in all the papers the Bureau drafted an outline to be followed in their preparation. To clarify the data in these circulars, which are in the libraries of many engineers and mining companies, and the summarized data presented in this paper, that portion of the outline dealing with cost and labor-performance data is reproduced below.

Jan 1, 1934

By Z. I. Zaki

Synthesis of TiC /A1203 Composite from TiO2, Al and graphite using combustion technique has been investigated at different initial temperatures; room, 400 and 600 °C. The effect of initial temperature on the composition of the product, wave velocity and combustion temperature of the reaction was studied. The measured combustion temperature and wave velocity were increased with increasing the initial temperature of the combustion reaction. The maximum wave velocity obtained was 5.9mms-1 when conducting the combustion reaction at initial temperature of 600 °C. Oxidation resistance of the obtained composite was also studied at the temperature range 300-800 °C. No oxidation is detected before 400 °C while it takes place effectively at 700 °C forming different titanium oxides. Wave velocity measurements method was used to calculate the activation energy of the reaction between the starting materials. It was found to be 316.34 kJ mol 1 at the temperature range that was studied.

Jan 1, 2007

By S. H. Ward

An account of a new method of investigating the electrical .properties J the earth's crust is presented. The method, called AFMAG, employs, as a source, natural alternating magnetic fields of audio and sub-audio frequencies. Measurements of the distortion of these fields caused by geological features are made with the aid of search coil detectors at several discrete frequencies. Many results of field surveys made with the method are presented and they illustrate its advantages and limitations when applied to the search for massive sulphide mineralization. The advantages far outweigh the limitations and in fact indicate that a major breakthrough in geophysical exploration technique and instrumentation has been made.

Jan 1, 1958

By F. Y. Kang

There are rich resources of natural graphite in China. It would be a good opportunity to upgrade national graphite industry if natural graphite with modification is used in lithium ion battery. Micro-crystalline graphite in high purity was coated with a carbon film on the surface. The initial cycle efficiency was improved to be 89.9% and cycle stability was remarkably improved. The experiments proved that microcrystalline graphite with carbon coating have excellent electrochemical performances at low cost as anode materials for lithium-ion battery. In addition, H2SO4-GIC technique was used to prepare the natural flake graphite powders with mild-exfoliation. Sub-micro and nano pores were found in the graphite samples. In correspondence the reversible capacity, rate capacity and cycle life were improved, which would meet the demand of high-power lithium-ion battery. Natural graphite is the most promising anode material for large-scale lithium-ion batteries. The demand of modified graphite grows up greatly in the market. Microcrystalline graphite with surface coating and flake graphite with mild-exfoliation are the promising commercial anode materials for the industry of lithium ion battery.

Jan 1, 2014

By A. Banerjee, J. P. Weiler, J. Jekl, J. T. Wood, R. Berkmortel

"The work presented here is part of an ongoing project designed to develop predictive capabilities of the local mechanical properties, and thus, structural behaviour of a thin-walled high-pressure die-cast AM60B magnesium alloy component. This work focuses on developing correlations between process parameters and local microstructure. Numerical simulations of the die filling and solidification behaviour of the AM60B component were used to estimate local process parameters such as solidification rate, temperature gradient, filling velocity, etc. These estimated parameters were used to establish semiempirical correlations with measured VALUES (of the local microstructure measured in regions throughout the component of different solidification conditions. INTRODUCTIONHigh-pressure die-cast magnesium alloys are experiencing increasing use in structural automotive components. A strength-to-weight ratio comparable to steels and its ease of castability allow for these alloys to be utilized in such capacities as instrument panel beams, seat and door frames, and engine cradles, among others (Gjestland and Westengen, 2007). However, the current use of these alloys is limited due to variations in local mechanical properties. These local property variations restrict part designers to assume lower than actual properties, resulting in larger sections, thus diminishing the light-weighting advantages of magnesium alloys. If these local property variations could be predicted, part designers would be able to optimize die-cast magnesium alloy components and fully take advantage of the light-weighting capacity of these materials.The work presented here is part of an ongoing project aimed at developing predictive capabilities of the local mechanical properties, and bulk mechanical performance, from variations in local microstructure, and ultimately from local process parameters in die-cast magnesium alloys. This project, unique in its nature, is based upon the results determined from fifty sequentially cast AM60B magnesium alloy instrument panel beams provided by Meridian Lightweight Technologies (shown in Figure 1)."

Jan 1, 2012

[Separates of all the Technical Publications published in 1930 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found in the Transactions.] Metal Mining Technical Publi- Title Author Meeting Tran~. cation Volume No. and Page* 264-A.29 Quicksilver Industry in 1929. Im- L. H. Duschak San Francisco T30, 283, 319 provements in the Metallurgy of C. G. Maier and Oct., 1929 Quicksilver and Symposium on The others Present Status of the Quicksilver Industry (With Discussion) (37) 271-A.30 Observation on Ground Movement R. E. Palmer New York T30. 168 and Subsidences at Rio. Tinto Feb.. 1930 Mines, Spain (20) 274-A.31 Development and Installation of the C.L.Berrien New York T30, 139, 166 Hawkesworth Detachable Bit (29) Feb., 1930 276-A.32 Protective Measures . Against Gas 0. A. Glaeser New York T30, 129. 167 Hazards at United Verde Mine (11) Feb., 1930 287-A.33 Use and Cost of Compressed Air (12) R. S. Lewis New York Feb., 1930 314-A.34 Miami Copper Company Method of F. W. Maclcnnan New York T30, 39, YO Mining Low-grade Orebody (44) Feb., 1930 319-A.35 How Human Beings Respond to W. J. McConnell New York Changing Atmospheric Conditions Feb., 1930 (9) 324-A.36 Vertical and Incline Shaft Sinking at Arthur B. Foote San Francisco T30, 87 North Star Mine (21) Oct., 1929 32bA.37 Governmental Control of the Pro- W. E. Colby New York duction and Sale of Mineral Re- Feb.. 1930 sources (With Discussion) (16) 333-A.38 Some Recent Developments in Open- E. E. Hunner New York T30, 106, 117 pit Mining on the Mesabi Range Feb.. 1930 (25) 334-A.39 Mining Methods and Costs at Presi- V. D. Howbert El Paso dio Mine of American Metal Co. of R. Bosustow Oct., 1930 Texas (15) 339-A.40 Operation of Pressure Fans in Series W. 8. Weeks New York (8) V. 6. Grishkevich Feb., 1931 364-A.41 Top Slicing with Filling of Slices as H. Willey El Paso Used at the Charcas Unit of Com- Oct., 1930 pania Minera Asarco, S. A. (17) 373-A.42 Drill Sampling and Interpretation of H. T. Matson New York Sampling Results in the Copper G. A. Wallis Feb.. 1931 Fields of Northern Rhodesia (17)

Jan 1, 1930

By P. H. S. W. Kulatilake

The presence of discontinuities strongly affects the mechanical and hydraulic behavior of rock masses. Joint geometry networks play a vital role in civil, mining, and petroleum engineering projects associated with jointed rock. The need for a realistic representation of joint geometry in rock masses has been recognized. The first part of the paper shows how to build three-dimensional stochastic joint network schemes and also shows how to perform validation studies for these schemes using joint data from the Stripa mine, Sweden. Due to the existence of complex joint patterns, mechanical behavior of jointed rock masses usually exhibit scale effects and an-isotropic properties. A correct understanding of the mechanical properties (strength and deformability) of jointed rock masses is important for designing and performance estimation of structures build in and on rock masses. Beyond a certain volume, the mass proper-ties of the rock may remain essentially constant with respect to the effect of joints. This minimum volume may be used as the element size to represent the equivalent properties of a statistically homogeneous rock mass volume which contains a significant number of joints. This volume may be termed as a "Representative Elementary Volume" (REV) and may be of great importance for engineering purposes. Investigations are underway at both the 2D and 3D levels to look into the possibility of establishing relationships between REV mechanical properties and joint geometry parameters. Recently developed joint geometry modeling schemes are linked with existing distinct element codes (both 2D and 3D) to create a stochastic/deterministic stress analysis approach in achieving the goal. Results obtained so far in this direction are presented in the second part of the paper.

Jan 1, 1992

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Exposure to respirable crystalline silica (RCS) can cause serious and irreparable negative health effects, including silicosis and lung cancer. Workers in coal mines have the potential of being exposed to RCS found in dust generated by various mining processes. The silica content of respirable dust in one single mine can vary substantially over both time and location. The current monitoring approach for RCS relies on the use of traditional air sampling followed by laboratory analysis. Results generated using this approach are generally not available for several days to several weeks after sampling, and this delay prevents timely and effective intervention if needed. An alternate analytical method is needed to reduce the time required to quantify the RCS exposure of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has developed a new method using commercially available portable infrared spectrometers for measuring RCS at the end of the sampling shift. This paper will describe the application of the new field-based RCS analytical process for coal mines, including the use of the new method with the existing Coal Mine Dust Personal Sampler Unit. In a case study conducted by NIOSH with a coal mine operator in West Virginia, field-based RCS analysis was completed at a mine site to evaluate the new technique. The RCS analysis results obtained by the field-based method in this case study showed sufficiently strong correlation with results obtained by the MSHA standard laboratory analysis method to allow the mine operator to use the field-based method for evaluating process improvements.

By M. J. Sheridan

"INTRODUCTION In December 1942, the-Bureau of Mines reported favorably on a proposal to grant Government assistance-in constructing an access road (consisting principally of a timber-pile bridge across the Rio Grande at Hot Springs, N. Mex.) to the property under lease to the United States Fluorspar Co. At that time the property was being developed actively, and there appeared to be no immediate-need for exploratory or metallurgical assistance by the Bureau of Mines.Because milling facilities were inadequate; the access-read project was eventually disapproved, but prior to disapproval the company had discontinued operations. In June 1943, exploration was resumed by the Humphreys Gold Corporation of Denver, which had subleased the property. Difficulty of access continued to interfere with exploratory progress. In July 1945, at the request of the lessee, the Bureau of Mines directed sampling, using company employees.At the completion of this sampling program, the Bureau of Mines concluded that the property was potentially a important source of fluorite but that further development for production appeared to depend largely on the establishment, by exploration, of adequate reserves. Because of the relatively easy position-of metallurgical-grade concentrate and ores, it also was deemed advisable to investigate the possibility of producing acid-grade concentrate from the ore, for which a demand was becoming evident. Accordingly, a program of trenching, diamond drilling, and metallurgical testing was undertaken by the Bureau. The results of its investigation are reported herein."

Feb 1, 1947

By Fernando O. Boechat

Com a redução da oferta de minério granulado de boa qualidade no mercado mundial e as restrições ambientais à sinterização, as pelotas de minério de ferro passaram a ocupar um papel importante como matéria prima para produção de ferro primário. Entretanto, embora apresentem maior resistência à degradação, as pelotas ainda sofrem com este problema, embora em menor magnitude, quando comparadas com granulados. Pode-se identificar a degradação das pelotas de minério de ferro em duas etapas, durante o manuseio e sob redução. Uma vez que vários estudos já analisaram a degradação durante o manuseio, a degradação durante a redução torna-se um assunto relevante e pouco explorado. Assim, o presente trabalho avaliou as energias envolvidas no movimento da carga ao longo de um forno de redução direta do tipo Midrex, usando o método dos elementos discretos. Para isso, foi utilizado o software EDEM® para obtenção das energias dissipadas durante as colisões das partículas. Aplicando estas energias ao modelo mecanicista proposto por Tavares e Carvalho [4] para fragmentação das partículas foi possível estimar a taxa de geração de finos no interior do forno. Estes resultados foram utilizados na previsão da degradação mecânica de pelotas no interior do forno, que previu a geração de 1,2 a 2,6% de finos gerados em um forno Minimod®, dependendo das premissas usadas.

Aug 1, 2018

By Ernesto Diez-Canseco Yañez

El siguiente trabajo señala los modos de aprovechamiento del mineral de carbón denominado "andracita", en tanto materia combustible de producción de las briquetas. Es decir, se busca crear un producto biocombustible que mantenga su calidad ecológica y que a su vez genere mayores posiblidades de venta en el mercado internacional, Para ello es necesario, evaluar el nivel de los aglutinantes en su composición y tratar de conservar sus características primigenias de dicho producto.

Jun 20, 1954

By V. J. Hucka

Coal, which was discovered in Utah in 1849, covers about 18% of the total area. Production in 1981 vas more than 14 million tons. However, some Utah coal mines are quite gassy. If longwall face technology is applied, then a release of a high volume of methane may be expected during the mining process. Investigations on methane content have been made by use of an isothermic bubble desorbometer. The desorbable methane content of 5 m3 to 16 m3 of methane per ton of coal mined has been determined.

Jan 1, 1983

Major Francis Hamilton Buchanan coined the term `laterite' (Latin; brick-rock) in 1807 for the red earths used for building blocks in southern India. Although these earths were actually weathered basalts, the term is now applied to weathering profiles developed upon a wide range of bedrocks. The Ni-laterites are a special class within the broad laterite family.

Jan 1, 1996

By Ani Chitaley

A new method has been developed for handling supplies in underground bituminous coal mines. A survey indicates industry wide implementation potential for the proposed method. Reduction of supply handling accidents' by as much as 73% and improvements in the productivity of face operations by at least 3% are anticipated benefits. The new method is based on the palletization of daily supplies and the use of a forklift for carrying out the handling tasks at the underground section. A prototype of the forklift has been delivered to the U.S. Bureau of Mines. The forklift has demonstrated several important features necessary for underground supply handling such as compactness, maneuverability, visibility, ease of control and auxiliary attachments for hoisting, carrying timber and pulling. Design improvements are recommended for future generation underground forklifts. These relate to higher speed, increased battery duty cycle, higher payload and modified traction/steering to eliminate plowing of soft mine floors.

Jan 1, 1983

By Alistair James, Mo Shahsavari, Leon Botham

Recent catastrophic failures of heap leach facilities have revealed fundamental weaknesses in prevailing design paradigms, modeling toolkits, and oversight practices that continue to treat heaps as static, free-draining earthworks despite compelling evidence to the contrary. The core proposition advanced in this paper is that heap materials are intrinsically dynamic: their structure, permeability, and shear strength evolve under the sustained influence of irrigation, climate, and geochemical reactions, and these timedependent changes can precipitate abrupt transitions from granular stability to flow-like failure. Drawing on investigations of recent failures at Çöpler Mine in Turkey and Eagle Gold Mine in the Yukon, alongside earlier incidents in Peru, Arizona, Nevada, and Chile, the analysis identifies a recurrent sequence driving catastrophic behavior: progressive weathering elevates fines and suppresses permeability; drainage systems designed for initial conditions become overwhelmed; pore pressures rise heterogeneously within the heap; and static liquefaction initiates rapid mass movement with long runout. Current guidance, including ICOLD and ANCOLD frameworks and ASTM testing standards, provides a necessary foundation but is tailored to tailings and conventional soil mechanics. These documents offer insufficient direction for characterizing timedependent material degradation, quantifying rheology of weathered ore, and modeling post-failure mobility. To address this deficit, the paper proposes an integrated framework combining enhanced characterization, multi-physics numerical modeling that couples hydro-geochemical processes with large-deformation mechanics, and comprehensive monitoring with Trigger Action Response Plans. The conclusion argues for a heap-specific standard that embeds these elements from concept to closure, aiming to materially improve safety performance and reduce the likelihood and consequences of future failures.

Feb 22, 2026

By Stuart St. Clair

EARLY in 1936, when the American Petroleum Institute issued -J "American Petroleum Industry," which was a survey of the current position of the petroleum industry, and its future outlook, and the figures for petroleum requirements .for 1950 and 1960 were widely publicized by the several oil journals, the impression was given that the petroleum- industry must be nearing maturity and would by 1950 have passed the high' point of its obligations to business progress in the United States.`' Let -us look at the figures which might conduce, this thought. Referring to p. 32 of the report, the total indicated crude-oil requirements in 1940 are 1,099,000,000 bbl-; for 1950, the peak, 1,109,800,000 bbl.; for 1960 a decline to 1,071,020,000 bbl. This downward trend, then established, is probably expected to continue. And this in the face of a crude production in 1935 of 993,942,000 bbl., 38,858,000 bbl.

Jan 1, 1936

By E. E. Maillot

In 1943, diamond drilling by the Bureau of Mines, comprising 11 holes which totaled 1,295.6 feet, showed that the pegmatite at Black Mountain consisted of shallow lenses in interbedded biotite-quartz-schist and impure quartzite. The average thickness of the pegmatite was 9.7 feet. Mineralization had a zonal arrangement. Beryl was most abundant near the footwall contact of the pegmatite. The average estimated beryl content of the pegmatite exposed at the surface was 0.81 percent, and the highest content of any pegmatite area was 1.75 percent. Other economic minerals were scrap mica, feldspar, spodumene, and lepidolite. Representative samples of the Black Mountain deposit failed to yield high-grade boryl concentrates by straight flotation owing to the presence of considerable spodumene. By employing heavy medium separation to remove the spodumene, 75.4 percent of the. BeO wan recovered in a flotation concentrate assaying 10.4 percent BeO.

Jan 1, 1949

By Y. Hwang, C Kang

To understand the effect of thermal loading from HLW on the groundwater flow nearby, the coupling of TH in an equivalent porous medium is studied. Results indicate that under given conditions the alteration of groundwater flow by decay heat is localized phenomena. More comprehensive studies are underway for THM coupling. Zum Verstandnis fur die Wirkung der thermischen Belastung von HLW in der Nahe von Grundwasserstrom, ist die Verbindung von TH in den entsprechenden porigen Medium erarbeitet. Die Ergebnisse zeigen, dass unter vorgegebenen Bedingungen die Anderung von Grundwasserstrom durch Zerfallwarme lokalisiert wird. Zusatzliche umfassende Arbeiten sind fur die THM Kupplung auf dem Wege. Pour comprendre l'effet du chargement thermique de HLW sur l'écoulement d'eaux souterraines tout près, l'accouplement du TH dans un milieu poreux équivalent est étudié. Les résultats indiquent que dans des conditions données le changement d'écoulement d'eaux souterraines par la chaleur d'affaiblissement est des phénomènes localisés. Des études plus complètes sont en cours pour l'accouplement de THM.

Jan 1, 2003

By A. W. Khair, L. D. Gehl

"This paper describes the study of bit wear characteristics on three types of rock namely Tennessee sandstone, Berea sandstone and Indiana limestone. High content of quartz with quartz cement in Tennessee sandstone causes removal of material from the bit body and dam2ge to the tip of the bit resulting into excessive weight and height loss as compared to other two types of rock. The drum speed and water spray pressure do not contribute significant effect on bit wear. The polycrystalline compact diamond (PCD) tipped bits are more wear resistant than the ordinary tungsten carbide (WC) tipped bits, but, due to wider body of PCD bits, the wear rate increases particularly at greater depth of cut. INTRODUCTIONThe impact of bit-rock interaction during the cutting process in underground coal mines has always attracted the-interests of mining operators, researchers and the manufacturers. Coal cutting bears directly on airborne coal dust generation which causes ""black lung"" in coal workers. On the other hand, rock cutting generates frictional sparks causing face ignitions. The bit wear not only produces airborne rcspirable coal dust , but also affects the productivity, safety and economy. Hun and Evans (J) concluded that the point attack bits have greater ignition potential than the conventional wedge shaped bits. The results of a study (2) suggested that after 7% of weight loss, the bit should be replaced. In a survey study (3), it was found that the bit consumption of bit had an effect on the productivity and utilization of the continuous miners. The mining industry is yet to receive a solution which could provide them with optimum operating parameters for coal cutting machines in underground C9al mines.The study was, therefore, taken up to determine wear characteristics as influenced by the rock propenies and varying operating parameters. For the purpose of this study, three types of rock, Tennessee sandstone, Berea sandstone and Indiana limestone were used. The machine operating parameters included (i) drum speed, (ii) water spray pressure and (iii) bit type. Besides studying the wear characteristics, the effects of these parameters on the required cutting force, specific energy consumption, acoustic emission generation and bit temperature rise were also studied. Also, the preliminary experiments were performed to compare the bit wear between PCD and WC tipped bits."

Dec 1, 1995