Search Documents

By Ralph P. Hackl

Ore at the Congress gold property, located near Goldbridge, British Columbia, is extremely refractory with most of the gold disseminated in fine-grained arsenopyrite. Metallurgical testwork conducted by Giant Bay Biotech Inc. indicated that biooxidation pretreatment was capable of increasing cyanide gold recovery from the ore to greater than 90%. To determine if the bioleach process could be successfully scaled up, a 225m' (7950-cu ft) commercial size bioleach reactor was built and tested at the mine site in 1989. At that time, the tank was the largest bioleach reactor ever operated. The objectives of the program were: • to ascertain if the biooxidation rates obtained in lab and pilot-scale reactors could be duplicated in a commercial scale tank; • to identify agitation conditions under which the process will function optimally; and • to demonstrate the bioleach process on a scale sufficient to satisfy the owners and potential investors.

Jan 1, 1990

By J. F. Brand, J. C. van Dyk, F. B. Waanders

"Syngas from Africary’s Theunissen underground coal gasification (UCG) project will be used for power production and synthesis of liquid fuels and commodity chemicals. However, some of the coal components, especially condensable water, oils, tars, inorganic trace elements, and a small fraction of fly ash and particulate matter, make their way to the surface via the production well and can cause adverse impacts on downstream processes. Africary’s standard design incorporates a cold gas clean-up system that relies on relatively mature techniques based on highly effective wet scrubbers and acid gas removal (AGR) systems such as Rectisol®, but with the downside of low energy efficiency and waste water generation. In this paper, novel technologies for removing contaminants and species separation from the hot (T > 300°C) raw syngas are compared. Comparisons are made between supersonic gas separation (SGS), Ranque–Hilsch vortex tube (RHVT), vortex gradient separation (VGS), and inertia vacuum filtering (IVF), and a vortex-based gas separation concept is proposed for UCG applications. IntroductionImpurities in gasification feedstock (coal, biomass, waste, etc.), especially sulphur, nitrogen, chlorine, and inorganic mineral matter, often end up in the syngas and can cause adverse impacts on downstream processes. Africary’s standard design incorporates a cold gas clean-up system that relies on relatively mature techniques based on highly effective wet scrubbers and acid gas removal (AGR) systems such as RectisolR, SelexolR or aMDEAR; but with the downside of low energy efficiency and waste water generation.Hot (T > 300°C) gas clean-up technologies are attractive because they avoid cooling and reheating of the syngas stream. Some available warm gas cleaning technologies include traditional particulate removal devices such as cyclones, candle filters, membranes, and molecular sieves. The warm gas desulphurization process technology developed by RTI LLC (2018) requires hot syngas to remove sulphur and has become commercially ready. Many other hot gas cleanup systems are still under development, given the technical difficulties caused by extreme environmental and operating conditions."

Jan 1, 2018

A variety of environmental financial assurance instruments are in use across the globe. This paper reviews some of the more common forms currently used in New Zealand, Canada, USA and Australia. In order to be effective, the form of assurance instrument selected needs to be aligned with a countryÆs specific environmental objectives, geography and political climates and also allow for a healthy investment climate. Industry and Government both have a strong interest in ensuring financial assurance criteria meet these objectives.   Recently Golder Associates have been involved in financial assurance assessments for various mining and quarrying companies across the South Island. Multiple stakeholders and regulatory agencies can make the setting of effective and fair financial assurance criteria a complex exercise for both regulatory agencies and industry.  The author relates experience gained in assessing financial assurance under current New Zealand legislation (RMA, 1991), effectively dealing with issues such as ôdouble bondingö and overviews potential approaches to dealing with transitional issues for historic and existing operating mine sites.

Jan 1, 2006

By Wils L. Cooley

Several aspects of coal mine safety-ground system operation are studied. Evaluations of two sophisticated ground-wire monitors are presented, along with a detailed report of development work on a modular ground-wire monitor. A portion of the report covers stray current flow in the safety-ground system, analyzing in detail conditions surrounding the generation of both dc and ac ground wire current. Considerable detail is provided concerning studies of mine ground beds. Additional progress is reported in the development of a. continuous ground-bed monitor, and new techniques are developed for the design of ground beds and their resistance measurement. New methods of accurately measuring electrical parameters of finite layered conducting structures are also reported. The effects of stray currents in ground beds is included. Touch-and step-potentials associated with mining equipment are analyzed, and methods are presented for determining earth voltage gradients around structures contacting earth. Instrumentation to determine gradients easily is suggested. Finally, an extensive effort is described dealing with lightning transients on open-pit coal mine ground systems. The nature of the transients, their expected frequency of occurrence, and the ways in which they damage equipment are analyzed in detail.

Jan 1, 1977

By A. T. Iannacchione

Underground limestone mines typically use the room-and-pillar method of mining in the generally flat-lying limestone formations. In some cases the dip may exceed 5° which can result in unique roof instability problems. Stability may be further exacerbated by the presence of horizontal tectonic stresses. Field studies and numerical model analyses are combined to assess the affect of the dip in various stress conditions. The results showed that where the horizontal tectonic stresses are sufficient to cause intact rock failure, increasing dip results in increased failure potential. The effect of the dip is greater when the maximum horizontal stress is parallel to the dip. Two case studies are presented and evaluated against the findings of stress analysis results. The study showed that the empirical rules of orienting headings parallel to the maximum stress are generally applicable to dipping excavations, except when mining in the up-dip direction. The importance of accurately determining the orientation of the maximum horizontal stress is emphasized because the window of favorable orientations relative to the stress is small.

By K. H. J. Clarke

"ALTHOUGH nickel was not identified as a separate element until a Swedish scientist, Axel Frederick Cronstedt, did so in 17 51, its utilization dates from pre-historic times. From its humble beginnings nickel has grown in importance until, today, in our clocks, television sets, automobiles, and air-planes, in our bridges, tableware, farm implements, and the equipment which processes our food, it is constantly at our service.For convenience in assembly, data and information relative to The Marketing of Nickel will be outlined in five phases: (A) Sources, (B) Distribution, (C) Utilization, (D) Market Development, and (E) Conclusions."

Jan 1, 1960

By R. L. Rickel

The Bureau of Mines, as part of its minerals environmental technology research, conducted a study of mine waste tailings disposal. Part of the investigation evaluated the sand bed dewatering technique for disposal of alumina mini plant tailings as a means to increase consolidation rates and contain effluents. The technique employs a bed of sand resting on an impervious bottom. The tailings slurry is impounded over the sand layer and is dewatered through bottom drain piping. The study employed a single 10-ft-high, 6-in-diam, clear polyvinyl-chloride (PVC) column, and thickener wastes from the acid leaching of calcined kaolin clay. Results showed a consolidation rate of 41 in in 186 days for a total volume reduction of 37 pct. Sand bed dewatering was an efficient technique for solid consolidation and effluent containment when compared with data obtained from other dewatering studies.

Jan 1, 1982

By Jerry T. Shelby

Surface and underground mining operations require equipment with high power output ratings. Haul trucks, loaders, dozers, and other equipment need increasing horse-power to meet production demands. To get more horsepower out of the engines driving the equipment, most manufacturers use turbocharging. Detroit Diesel puts the number at about 90% turbocharged, while Caterpillar estimates 75% to 80% of all its equipment is turbocharged. Turbocharging increases the power output and overall engine efficiency. But it presents some maintenance and operational problems that were not factors when only naturally aspirated engines (nonturbocharged) dominated the scene. A turbocharger is an exhaust-driven air compressor. Using the waste energy in the engine exhaust, a turbine wheel is driven. This wheel is connected by a common shaft to a compressor wheel. The shaft is supported by two plain bearings, or bushings. As the turbine wheel is rotated, the compressor wheel continually compresses the intake air to the cylinders. Compressing the intake air means that more air can be put into the cylinder to burn more fuel. The more fuel the engine can completely burn or combust, the more horsepower the engine can produce. Even though the turbocharger is a relatively simple device, it is a sensitive engine component. It requires special consideration at engine start-up and shutdown. Being freewheeling and exhaust driven, turbochargers can experience temperatures of 540°C 1000°F) and rotational speeds of more than 100,000 rpm. Due to those temperatures and speeds, lubrication is critical to the operation and life of a turbocharger. The turbo is located high on the engine, with the oil supply running through an external line from the sump. The recommended practice is to start the engine and allow it to idle for a few minutes before any revving or loading. This allows the oil to reach the turbo and properly lubricate the bearings before high rotational speeds are seen. Turbo oil supply lines can be as long as 1.5 m (5 ft). Depending on ambient temperatures and oil viscosity, it can take as long as 30 seconds for oil to reach the spinning turbo. However, as little as five seconds without oil can damage the turbo's bearings, reducing its life and overall efficiency. Lubrication problems seen at shut-down can also significantly affect turbo life and efficiency. Manufacturers recommend an idling period of five to seven minutes before engine shutdown. This allows the turbo to slow down and cool off somewhat to help prevent oil coking and bearing damage. When the engine stops, so does the oil supply. There is very little oil left on the bearing surfaces and in the turbo oil supply passages. The immediate heat transfer from the turbine wheel to shaft, bearings, and turbo body literally cooks what is left. This high heat without oil flow can cause bearing deformation by actually melting some of the bearing material. The rapid oil oxidation and coking will restrict oil passages, damage bearings and shaft. Besides heat soaking, there is another problem. If the turbo is spinning at high speeds when the engine is shutdown, the turbo must spin-down to a stop without oil flow. With the large size of turbos used on mining equipment, this spindown time without oil can be for as long as 10 to 20 seconds. Fortunately, lack of lubrication at start-up and shutdown and the subsequent bearing damage can be prevented by oil injection devices. These devices hold a reservoir of engine oil. The oil is injected to the turbocharger bearings immediately on start-up and for several minutes after shutdown. Oil injection devices are spring loaded, hydraulic accumulators. They are actuated at start-up by a solenoid wired to the starter motor. Engine oil pressure charges the accumulator during normal operation. Upon shut-down and loss of oil pressure, the device provides oil to the turbo for about two or three minutes. With an oil injection device, the engine can be started and immediately driven without fear of turbo damage. Also, an abrupt shutdown will not damage the turbocharger since the device will continue to lubricate for two or three minutes. A word of caution. Be sure the oil injection device provides positive oil displacement (pressurized oil flow). Do not use a gravity-flow device. Unless it is a true accumulator, the device could starve the turbo for oil on start-up, Ask for start-up and shut-down pressures and delivery times before considering installation. Keep the oil clean, and follow the manufacturer's recommended oil change intervals. These intervals are usually shorter than with naturally aspirated engines. Use oil with a CD rating designed for diesel applications. A multiviscosity oil is preferable. Use a synthetic engine oil, such as Mobil's Delvac 1, Gulf's Super Duty II, or Chevron's Sub-zero Fluid. Synthetics have much better flow properties at low temperatures. They also have greater oxidation stability (they can take the high heat of turbo-bearing lubrication. And they produce fewer deposits because they are more thermally stable. But synthetic oils do cost more - two or three times more. One additional point - maintain the air intake system. Since all mining is usually in a dusty environment, air filters should be changed regularly and intake systems should be checked for leaks. All intake air passes through the turbo. Any dirt or abrasives entering the turbo will damage the unit and shorten its life. While mining is a heavy duty business with severe operating conditions, you can get the life from your turbocharger that you expect by following a few simple steps: • equip the turbo with an oil-injection device to provide lubrication on start-up and shutdown; • change the oil and filters regularly; and • use the proper oil-synthetic, if possible.

Jan 3, 1987

By Lloyd Williams

1. The investigation shows that the Pewee, Big Mary, and Windrock are the most important beds in Anderson County. About 73 percent of the known recoverable reserves of coal in the county are in these beds, and from them comes 94 percent of the production. The remaining reserves tabulated in this report are in the Joyner, Jellico, Coal Creek, and Poplar Creek beds, and 6 percent of the county production comes from these beds. No production is being reported at present from the Jellico bed, although it was mined years ago. 2. Known measured and indicated reserves in all beds, bared on a minimum thickness of 1/4 inches and on 1,800 short tons put acre-foot of coal in place, are estimated to be 170 million torts as of January 1, 1953 Of this total, 155 million tons is in beds 2S inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to they total estimated reserves.

Jan 1, 1955

By E. C. Westman, W. R. Thomas, W. J. Conrad, A. J. R. Russell

"Understanding ground control problems continues to remain a focus of the mining engineering community. To aid mine operators and engineers in identifying and responding to ground control issues, the Ground Observation System (GOS) is being developed. The GOS is an integrated, web-based graphical user interface that displays ground response data collected wirelessly from an underground mine. It presents data in an intuitive manner to assist mine personnel, who are on- or off-site, in quickly identifying hazardous areas. Geotechnical instrumentation will be connected to wireless transmitters that will relay data in real-time to a surface computer that stores the information in a database. The GOS website will then display the geotechnical data in graphical and tabular forms, as well as in conditionally formatted mine maps. Data from each measurement device will be able to be viewed in its entirety or within a time interval, and can be downloaded for further analysis. The ability of the GOS to quickly interpret and communicate mine hazards to personnel of varying technical ability should prove to be a useful tool in understanding ground control and thus improving mine safety.INTRODUCTION Computer-based data information centers that convey operating parameters and conditions are prevalent in modern underground mines. Today’s systems are popular in showing ventilation controls and monitoring equipment performance (Jyothi & Meena 2013). In ground control monitoring, Conover, Ross, and Bigby, 2010 have installed a wired telltale roof monitoring system that sends roof displacement data every ten minutes to a computer on the surface. The computer receives, stores, and displays the data in real time. Data can also be viewed remotely through a password protected internet connection. Additionally, an internet connection allowed for remote updates to the system which streamlined software development and maintenance by eliminating travel (Conover et al., 2010). Currently, no such system beyond Conover et al.’s design has been accomplished. The Ground Observation System (GOS) is being developed to fill the void of real-time geotechnical monitoring in underground mines. A wide array of data will be transmitted wirelessly and broadcasted to on- and off-site mine personnel through the internet. The GOS will incorporate geotechnical data from roof deformation, borehole scratch testing, photogrammetry, and seismic monitoring into one interface, all while achieving permissibility for the use in gaseous mines. As a result, a comprehensive view of rock movement due to mining will be available. The overall purpose of the GOS is to deliver warnings; to ensure reliable data is relayed to personnel for the identification of potential ground failures, provide mine engineers information to design more stable mines, and assist with further geotechnical research."

Jan 1, 2015

By Clinton C. Knox

To demonstrate the feasibility of unwatering ore reserves previously indicated in the virgin Melrose zinc-lead field in Kansas and Oklahoma, the Bureau of Mines .carried through a pumping project on the Park Walton farm in 1943. Due to success of the undertaking, attention was turned to exploration of other indicated ore deposits and promising areas within that part of the field benefited by .the drainage project, By the middle of 1946, four private mining companies were active in the field; and a considerable output of lead and zinc concentrate had been obtained from the new Park Walton mine and mill. The Park Walton Ore deposit was unwatered by installing deep-well pumps in three holes previously drilled by the lessee. Pumping was continued by the Bureau of Mines at a rate of 2,500 to 1,000 g.p.m. for about 6 months; during this time the local static artesian water-level, originally averaging 108 feet below the surface in the old drill holes was lowered to the 316-foot level, which justified beginning the initial shaft sinking and mine developments. In all, about 750,000,000 gallons of water was pumped by the Bureau of Mines at an operating cost averaging $0.024 per 1,000 gallons.

Jan 1, 1948

By P. A. Lawless

The objective of the research performed A for the Bureau of Mines on this contract was to develop a portable instrument for the detection of carbon monoxide (CO) in a mine environment. The desired characteristics were sensitivity and specificity for CO with a stable calibration. The sensor of the instrument was to be of metal oxide composition, requiring low power for compatibility with the types of batteries presently used in personal equipment in mines. The solid state design was also desired for ruggedness and small size. A key design feature of the instrument was to be provided by adherence to the intrinsic safety design requirements for electrical equipments operated in potentially exposive mine atmosphere. The Research Triangle Institute has prior experience in developing a solid state oxygen sensor using a thin film of zinc-oxide (Ref. 1) and experience in fabricating thin film devices. Solid state sensors utilized by other workers (Refs. 2, 3, 4, 5, 6) have included metal and semiconductor films and crystals of materials like carbon and aluminum oxide for the measurement of water vapor in the air and have relied upon measuring resistance and capacitance changes in the sensor in response to adsorbed vapors or gases. Since the effect of carbon monoxide in changing the resistance of various materials such as molybdenum, platinum, and zinc oxide had been reported (Refs. 7, 8, 9, 10), the requirements appeared to be realisable, although it was recognized even at the inception of the work that specificity to carbon monoxide might require the incorporation of more than one sensor.

Jan 1, 1976

By Raphael Banda

1 Initiating Systems ? a definition An initiation system is a combination of explosive devices and component accessories specifically designed to convey a signal and initiate an explosive charge from a safe distance. In the use of explosives, the initiating system performs the functions of transmission and control of the firing signal to each explosive charge. As functional groups, initiating systems may be considered as: Starters Those which provide the initial signal to start the blasting process. Surface systems Products which provide transmission of the starter signal and delay timing (if any) across the surface of the blast outside the blast hole. In-hole systems Products which provide the signal transmission, delay timing (if any) and the initial explosives energy in the blast hole.1 2 Different types of Initiating Systems The initiation systems commonly used in Sub Saharan Africa are: ? Detonating cord and detonating relay systems ? Capped fuse and igniter cord systems ? Shock tube non electric systems ? Electric systems ? Electronic detonators 3 Overview of Electronic Delay Detonator Technology Conventional detonators use pyrotechnic delay elements and the variation of the actual delay periods is at best approximately 1% the nominal delay. The lack of guaranteed precision common to all pyrotechnic systems enhances the likelihood of negative environmental blasting effects.3 For example, take a 500 ms in hole delay. In conventional detonators this means that 95 % of shots fire within 10 ms of the mean. i.e. a window of 20 ms. Taking a fixed interval between shots of 25 ms, with a range of ± 3 ms, a very ragged firing pattern could be expected which in practice would result in non uniform fragmentation.

Jan 1, 2005

By Laurence G. Britton

Accurate flammability and ignitability data for chemicals form the cornerstone of procedures used to assess the hazards associated with commercial chemical production and use. Since 1967 the ASTM E27 Committee on the Hazard Potential of Chemicals has issued numerous, widely used consensus standards dealing with diverse testing and predictive procedures used to obtain relevant chemical hazard properties. The decision to issue a standard rests solely with the membership, which consists of representatives from industry, testing laboratories, consulting firms, government, academia, and instrument suppliers. Consequently, the procedures are automatically relevant, timely, and widely applicable. The purpose of this paper is to highlight some of the widely used standards, complemented with hypothetical but relevant examples describing the testing strategy, interpretation, and application of the results. A further goal of this paper is to encourage participation in the consensus standards development process. The paper is published in two parts. The first part (in the preceding issue of Process Safety Progress) dealt with the E27 standards pertaining to thermodynamics, thermal stability, and chemical compatibility. The second part, published here, focuses on the flammability, ignitability, and explosibility of fuel and air mixtures. © 2005 American Institute of Chemical Engineers Process Saf Prog 24: 12?28, 2005

Jan 1, 2005

Recent U.S. mine disasters identified a need for improved training of miners in escape from mine fires and explosions. Researchers at the National Institute for Occupational Safety and Health?s (NIOSH) Spokane Research Laboratory (SRL) have designed fire-escape training software for use in a mine-safety training course. The software allows four trainees to work together in a virtual world via a computer network. Trainees responded favorably and showed a marked improvement in locating the proper evacuation routes on subsequent trials. In collaboration with the Pittsburgh Research Laboratory (PRL), a more elaborate fire evacuation scenario is being developed. Further study is needed to confirm that virtual training will translate to improved safety outcomes in the real world. Keywords: virtual reality (VR), safety, training, mining, mine fire evacuation

Jan 1, 2009

The importance of understanding the behaviour of cemented paste backfill (CPB) within the framework of the effective stress concept is highlighted in this paper. Only through an understanding built on this concept can problems such as barricade loads, the rate of consolidation and arching, be fully understood. The critical importance of the development of stiffness during the hydration process, and its impact on factors such as barricade loads, is used to illustrate why conventional approaches that implicitly ignore the effective stress principle are incapable of capturing the essential components of CPB behaviour.

May 1, 2007

By C. W. Davis

This paper is the second of a series of progress reports on a study, of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States. There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value. One ,of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although Several manganese minerals acre readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.§. Recent experiments have shown that a roast at 650 to 900°C converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution. Introduction of smelter gases containing as much as 5 per cent SO2 during such a roast would not add much to the cost of the operation and might result in the formation of considerable water-soluble manganese sulphate.

Jan 1, 1930

By T. B. Acton

There are two types of ore transportation systems in use at Newmont's Magma Copper Co. San Manuel mine in Arizona-rail-mounted, box-type rotary cars and the newer rail-mounted, bottom-dumping ASEA cars. Though the cost per car for the ASEA units greatly exceeds the cost per rotary car, the advantages of the ASEA units, including much faster dump times, have made the ASEA system a successful alternative at the San Manuel mine. The rotary system of ore transportation has been in use at San Manuel since production began in 1956. The system employs 7.9-m3 box-type cars to transport ore by rail to shaft pocket areas. A rotating dumping mechanism turns three cars at a time upside down to empty them, and returns them to an upright position. Trains of 15 cars each are dumped in about six minutes. Each 15-car train is pulled by an 18-t rated trolley locomotive. There are about 400 rotary cars in service at San Manuel and the system is used for the majority of ore haulage. This well-proven rotary method was instrumental in achieving the December 1977 world record of 272 Mt hoisted from an underground copper mine. Magma Copper Co. began using ASEA cars in late 1977. Designed by ASEA of Sweden, the cars are built for San Manuel by Kasper-Hall Manufacturing Co. in Tucson. The cars basic design feature is a hinged floor that opens at the side as the car is pulled through the dump. As it passes over the dump, a fifth wheel attached to the hinged floor (opposite the hinges) travels along a rail in the dump. This rail dips down into the pocket and then returns to track level. As the fifth wheel travels along the rail, the car floor opens, the car dumps, and the floor is then returned to track level. As the car is dumping, the body remains suspended over the pocket by wheel rollers attached to each side of the dump. Trains of 10 cars each are emptied in about 45-50 seconds. Each ASEA train is pulled by an 18-t rated trolley locomotive, adapted at San Manuel to allow it to pass through the ASEA dump. At minimal cost, "wings" are welded to each side of the locomotive. These wings suspend the locomotive over the pocket as the train passes through the dump. Advantages of the ASEA System Major design characteristics of the ASEA and rotary systems are shown in the accompanying table. The comparison points out some of the following advantages demonstrated by the ASEA system. • Faster dumping-An ASEA train dumps in 50 seconds, while a rotary train takes at least six minutes. There is no stopping or starting when dumping an ASEA train. The train enters the dump area, dumps, and leaves in one continuous motion-in contrast to rotary trains which must stop and start five times to dump. With the rotary system, three cars are spotted in the dump mechanism by remote control. When the cars are in place, the train operator activates the dump, the cars are turned over, and then returned to an upright position. This process is repeated until all 15 cars in the train are emptied.

Jan 4, 1980

By Caroline B. Chapleau, Mélanie Proulx, Claude Bazin, Gaétan Lavoie

"Quebec Cartier Mining operates a pelletizing plant in Port-Cartier, QC. Grinding, agglomeration and pellets induration are the three main steps in the preparation of iron oxide pellets. In 1998, following different recommendations, the company increased the speed of one of its ball mill in order to increase the grinding efficiency of the machine. As expected, the increased speed lead to an increase of the power draught, which did not produce the expected increase of fineness of grind, neither its allows to increase the mill throughput. The change of behaviour of the mill could hardly be understood by comparison of discharge size distribution at initial and modified mill rotation speed. On the other hand, the use of the selection function from a population balance model provides an insight of the changes that occurred in the mill. This paper reviews the various steps required for the estimation of a grinding mill selection function. Results of the calibration to Quebec Cartier grinding mills show that the increase in the mill speed leads to higher rate of breakage of coarse particles, at the expenses of less efficient breakage of medium and fine size particles. In the case of the studied mill, breakage of coarse particles was probably not the critical step of the mill operation. INTRODUCTIONOre size reduction is the major energy consumption step in any mineral processing operations (Austin et al., 1984). Size reduction is required to either liberate valuable minerals from the gangue minerals in which they are imbedded, or to increase the specific surface of the ground material. Plant engineers continuously face the challenge to find grinding machines, operating conditions or grinding circuit flowsheet configurations that could improve the size reduction process at lower energy or m6dia consumption."

Jan 1, 2000

By Stephen J. Harven

Geologic conditions in eight northern operating sections of Jane Mine, Keystone Coal Mining Complex. Armstrong County, Pennsylvania are defined by utilizing drillhole data and underground geologic mapping. Three of the eight sections are experiencing difficult mining conditions in the Shelocta "0" coal seam (formerly the Lower Freeport). The five remaining productive sections will exhaust their reserves within one year. Coordinating mine planning with future production levels is aided by indicating areas that appear favorable and lack the geologic conditions that cause difficult mining. Roof rock 1 ithologies, lithologic variations in and below the floor, jointing, overburden thickness, coal splits, paleochannels. and clay veins are the principal geologic factors believed to influence mining conditions in Jane Mine. Careful definition of each cause allows for a reasonable assessment of future mining conditions.

Jan 1, 1987