Search Documents

By Madan Kumar Annam, Hari Krishna Y

"Basement construction is one of the challenging geotechnical concerns in the urban environment. Several types of retention systems are practiced to support the earth which is suitable for restricted access, rapid mobilization, fast excavation and cost-effective designs. A thorough understanding of geotechnical engineering as well as the structural mechanics is important for the earth retention systems. This paper discusses a project with various types of foundation solutions including monitoring of deflections during excavation stage of a retention system.A multi storeyed residential building (3B+Stilt+18F) in Chennai having structure foot print area of 1500 m2 has to be constructed on large diameter pile foundations and also to support the proposed basement excavation. Ground water table was encountered at about 6m below the existing ground level (EGL). In order to support heavy structural loads, large diameter bored cast-in-situ piles were chosen and installed. Further, complete retention system was economically designed and built, which includes installation of Contiguous Bored Piles (CBP) in combination of vertical grout columns behind CBP wall to seal the gap between the CB Piles, installation of inclined ground anchors, construction of capping beam, stressing and locking of installed ground anchors. A detailed monitoring program was in place and continuous monitoring of wall deflections is being measured at the time of publishing this paper. This paper describes the design and construction aspects adopted for foundation and retention system including the monitoring results during excavation stage of the project.INTRODUCTIONIn general, stage wise open excavation will be opted for basement construction where plenty of space is available. Due to urbanization and restricted space, open excavation became a difficult task nowadays. To overcome this problem, suitable retention system need to be selected to retain the soil mass. Selection of suitable retention system for multi-level basement excavation is a great challenge in geotechnical industry, especially when the proposed site is located within the minimum set back distance from the existing structures. This in turn calls for the advanced and innovative methods of retention system.Several earth retention systems such as Diaphragm Walls, Secant Pile Walls, CBP system, Soldier Pile Walls, Sheet Piles, Deep Soil Mixing (block walls) etc. with or without inclined ground anchors are being practiced worldwide. Considering the advantages and disadvantages of the available retention systems in practice locally and keeping in view of present site conditions, the developer has chosen CBP system with inclined ground anchors so that all foundation related works of the project will be handled in a single package. The main advantage of such packaged solution will ease the coordination between design consultants and foundation contractor resulting in faster construction of foundation works which in turn reflect savings in time and cost."

Jan 1, 2015

By R. R. Sayers

"An important, function of the U.S. Bureau of Mines is to instruct miners in first aid, and as a means of promoting interest in it first-aid contests are held under the auspices of the Bureau, usually in coop; ration with other interested organizations, especially the American Red Cross, the National Safety Council and various operators' and Miners' associations. It was early found that the method of judging first-aid meets is one of the most vital factors in determining the degree of success of the meet.It may be safely stated that there is no method for the judging of first-aid contests that has proved ideal. A method that would give the most uniform judging would necessitate the rating of each team by the same judge or committee of judges and, in order that a judge may rate a team satisfactorily, he should see that team perform several events and average the ratings. Such a procedure is not practicable where there are many terms entered in the contest, as it would prolong the meet indefinitely. To overcome this objection the method has been tried of assigning separate judges to each team but this brings in a new factor the individuality of the various judges, some of whom rate closely, others loosely. The next development was to average the judging by having the judges rate different teams for each event. This would seem to solve the problem out it has been found, after using the method over a wide area for a considerable period of time, that the differences in the judging are too marked to be at all satisfactory. The next development was to appoint a committee of chief judges three to five in number especially trained and experienced, to aid the individual judges in rating the teams. This method has proved satisfactory at small meets but, as committee must review the work of each judge on each event, it has not been deemed feasible for a large meet."

Nov 1, 1920

By N. H. Grace

"IntroductionDURING the past half century, the economy of Western Canada was largely centred on agriculture. However, the impact of World War II has led to an acceleration in the development of a variety of natural resources so that, today, Western Canada is experiencing great industrial development. Consequently, the availability •of low-cost energy assumes prime importance. In the final analysis, industrial growth and expansion are intimately linked to the energy resources.Coal ReservesHas Western Canada adequate coal reserves to meet the present accelerating demand for power in the days that lie ahead? This question must be answered before detailed consideration can be given to the probable patterns •by which various energy sources in Western Canada may be expected to meet the expanding demand. Figure 1 indicates the extent and distribution of the Canadian coal reserves, the data having been prepared by Dr. B. R. MacKay for the Royal Commission on Coal in 1946 (1). The amount of readily recoverable coal is listed as one-half the quantities shown on the chart. It is interesting-to note that upwards of 90 per cent •of the Canadian coal reserves .are located in the three most westerly Canadian provinces. It has been estimated that the coal reserves, at the present rate of mining, would be adequate for about 3,000 years. Consequently, it may be concluded that the coal •reserves in Western Canada •are indeed adequate to meet tremendous energy demands for many centuries. When the oil and natural gas have been exhausted, the great coal reserves will still be available."

Jan 1, 1953

By J. R. Thoenen

During the past 6 years the Mining Division of the U.S. Bureau of Mines has prepared many information circulars containing valuable technical data covering the operating details of mining and ore-dressing plants throughout the United States, Canada, Mexico, and other countries. These papers, written for the most part by operating officials in the field, have been designed to comprise a reference library for the operating engineer. In order to make the information contained in these publications more readily available to the busy engineer the enclosed series of reference tables has been compiled. The tabular arrangement is by subject rather than alphabetical order, thus avoiding the bulk of an alphabetical index.

Jan 1, 1935

By James M. Franklin

Research on modern hydrothermal systems provides quantitative measures of the processes of formation of hydrothermal fluids and of precipitation mechanisms from them. Studies of ancient deposits provide new information regarding volcanological processes that are related to the deposits, as well as data on their spatial and temporal compositional variations. Mew exploration guidelines result from both aspects of research. The most fundamental requirement for large metalliferous hydrothermal systems is an abundant heat supply for the upper two kilometers of the crust. This heat may come from a focused heal source (shallow-level subvolcanic intrusion), but ambient heat also may have provided enough energy for the reactions necessary to effect leaching of metals, especially where heat flow is particularly high (i.e. very large or high-temperature magmatic source, such as ultramafic environments). For most VMS systems, the majority of the metals were derived through leaching from footwall strata; in addition interstratal fluids may enter subvolcanic intrusions during episodes of magma a chamber "cracking," engendering some '?magmatic" component in the hydrothermal system. Direct contributions of metalliferous magmatic fluid also may be significant from arc-related or back-arc felsic or alkalis systems. These latter contributions may form exceptionally high - grade portions in some deposits. Subvolcanic intrusions, which are excellent indicators of high heat flow and may have been the direct driving mechanisms for some stems undergo two stages of alteration: On intrusion emplacernent. fluids may rapidly enter and react with their mesostatic portions, evident in the sills in the Middle Valley. High temperature interactions caused albitization and destruction of oxides and sulfides, releasing metals. During terminal hydrothermal stages, the metalliferous fluid collapsed into the intrusions, forming disseminated and vein sulfides.

Jan 1, 1998

By Barun Gorain, Andy Stradling

"The traditional metallurgical scale-up techniques for flotation plants are based on lumped flotation rate constants, dimensionless hydrodynamic numbers and the use of safety factors. Once the plant has been designed, the flotation principles that govern scale-up play almost no role in the optimisation of the circuit to meet its metallurgical targets. This deficiency can potentially lead to a plant design incapable of meeting its targets, especially when circuits incorporate large flotation cells. This paper demonstrates the application of the k = PSbRf model in providing a suitable framework for flotation modelling, scale-up and circuit optimisation, thus presenting an integrated approach to the problem. Studies were conducted at Teck Cominco’s Red Dog concentrator to characterise cell hydrodynamics, gas dispersion properties, fioth flow behaviour, entrainment and ore floatability to obtain the key data necessary to develop a model for the flotation circuit. The findings of these studies are presented in this paper, which provide valuable insights into the modelling and optimisation of the Red Dog flotation circuit.INTRODUCTIONThe traditional methodology for flotation scale-up and plant design is based on the rule-of-thumb with safety factors, dimensionless hydrodynamic group similitude considerations, etc. With the recent trend towards larger flotation cells with volumes of 150 m3 and greater in concentrators, the problem of scale-up has become even more acute. The scale-up factors that may have been tolerated on smaller cells are not applicable to larger cells. The transportation of froth in these large cells adds further complexity to the problem. Arbiter et al. (1980) foresaw this problem and pointed out that if scale-up were attempted by rule-of-thumb and trial-and-error, then the probability of failure would increase with scale. This problem is confounded by the fact that the design and scale-up considerations used for a new flotation circuit play almost no role in optimisation of the circuit to meet its metallurgical target. This results in a plant design incapable of meeting its metallurgical targets. There have been several instances where new concentrators have required significant circuit modifications and additional capacity to achieve design targets."

Jan 1, 2002

By L O. Filippov, C H. Veloso de Melo, A Correa De Araujo

Froth flotation of iron ores is one of the most widely used methods to upgrade iron ore into high-grade concentrates. In recent years, reverse cationic flotation of iron ores has been specifically the subject of several studies. Since quartz is the most common gangue mineral in iron ores, understanding the behaviour of this mineral was the main target of the majority of such studies. However, with the depletion of mineral deposits considered rich and easy to process, it has become more common to find iron ores with complex gangue minerals, which are composed not only of quartz but by a variety of silicates. The mineralogical composition of the ore is an important factor for determining reagents and mineral processing parameters. The mineralogical suite of an ore also presents a paramount role for operational optimisation of any given flotation process. Some studies were performed with different types of amphiboles and other Fe-bearing silicates, for example, but the influence of the mineralogical nature of these silicates in reverse cationic flotation has not been fully explored and will be discussed here. Changes in the traditionally used reagent scheme for reverse cationic flotation, generally including alkaline pH values, polysaccharides as depressant (mainly starches) and primary ether amines and diamines, are expected when dealing with iron ores with complex silicate gangue composition.CITATION:Veloso de Melo, C H, Correa de Araujo, A and Filippov, L O, 2017. Reverse cationic flotation of iron ores with complex silicate gangue minerals, in Proceedings Iron Ore 2017, pp 241–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Ted C. Briggs

A special high-pressure Burnett-type compressibility apparatus was constructed and used to determine compressibility factors for pure helium, pure nitrogen, and nine helium-nitrogen mixtures containing 89.47, 79.04, 69.69, 60.09, 49.24, 41.02, 30.99, 20.53, and 10.67 mole-percent helium. A total of 161 runs were made consisting of 2,355 observed pressures. Data were obtained at 0°, 25°, and 50° C and at pressures to 1,000 atmospheres. A power series in the reciprocal volume, commonly called a Leiden series, is used to represent the compressibility factors. Three parameters in the series are required to represent helium, five parameters to represent nitrogen, and from three to five parameters to represent the mixtures. Compressibility factors are believed to be accurate to better than 0.1 percent over the entire pressure, temperature, and composition range.

Jan 1, 1972

By Thomas J. Peters

The Goat Rocks RARE II further planning areas contain no known mineral resources and have very low mineral potentials. County mining records show only one mining claim area; however, no mineralized material was found at the described location. Andesite suitable for building stone may be present, but similar material can be quarried more economically elsewhere. Several anthracite coal prospects are near the area, but the likelihood of finding an economic deposit of coal or other fuel is very low.

Jan 1, 1981

By Vince Luongo

PROJECT DESCRIPTION The York Durham Sanitary System (YDSS) Interceptor in the Town of Richmond Hill located just north of Toronto, Ontario, Canada will see the construction of a tunnel extending along 19th Avenue for a length of approximately 3.8 Km from Yonge Street, east to Leslie Street and will have a minimum internal diameter of 2.1 m. t to Leslie Street and will have a minimum internal diameter of 2.1 m. The tunnel will connect into four shafts, for which two of the shafts will be constructed using the slurry wall construction method given the high water table and difficult ground conditions encountered at these locations. The two shafts noted as Access Shaft No. 2 and No. 3 were designed and constructed to meet regulatory conditions, which required a sealed shaft construction method. GEOGRAPHICAL PROFILE The ground conditions in the Toronto region consist predominately of glacial till, glaciolacustrine and glaciofluvial sand, silt and clay deposits, and beach sands and gravels. The shallow geological formation found in the project area consists of four types of deposits: Oak Ridge Morain deposits, Halton Till, Glacial lake deposits and Organic soils. The Oak Ridge Morain is the dominant deposit encountered along the tunnel alignment. This formation consists of three deposits: The Upper Till, Middle Sand and the Lower Till. Standard penetration tests (SPT) carried out in these deposits measured N-values ranging from 2 to more than 100 blows/300mm which indicate very loose to very dense soil conditions. The Middle Sand deposit will be the dominant feature within the slurry wall construction at access shafts 2 and 3. Access Shaft 3 The base of the slurry wall will be 20.5 M below the ground surface. Slurry wall excavation will be within peat and organic soils found at the upper 3 M, followed by 5 M of the Upper Till. The remainder of the excavation will be within the Middle Sand. The piezometric head elevation is found at the ground surface. Access Shaft 2 The base of the slurry wall will be 22.5 M below the ground surface. Slurry wall excavation will be entirely within the Middle Sand 2.The piezometric head elevation is found at 7 M below the ground surface.

Jan 1, 2007

By D. H. Rubisov, V. G. Papangelakis

Sulphuric acid pressure leaching is the process of choice to recover nickel and cobalt from laterites with variable iron and magnesium contents. The latter influences the acidity levels required for effective leaching of nickel and cobalt, and during leaching, iron is rejected in-situ as hematite. Classical solid/liquid separation is performed via a CCD circuit, the performance of which depends upon the size and shape of precipitated particles. In this paper, precipitates obtained by acid-leaching of various lateritic feeds at 270°C are characterized using SEM/EDX and laser particle size analysis. It is shown that as acidity increases, the shape of the precipitates gradually changes from platelets to spheres, thus improving the S/L separation properties of the residue. The use of hydrogen ion concentration “at temperature,” calculated from a speciation analysis, allows the explanation of this change of morphology independently of the type of the ore feed. The possibility of precipitating magnesium sulphate “at temperature” is also discussed. In order to take advantage of this precipitation for scale reduction (as has been proposed in the past) without compromising the residue quality, [H+] “at temperature” must be controlled within an optimum range.

Jan 1, 2000

By T Wambeke, J Benndorf

A risk-robust development of a heavy mineral resource requires an assessment of the geological uncertainty and spatial variability of the key factors impacting the mining and processing operation. Attributes of interest are the total heavy mineral grade, the slime content and the amount of oversized particles. The modelling of a mineral sand deposit presents two main challenges. Firstly, the exact location of the geological boundaries are obscure due to the complex interaction of the deposit formation processes. Secondly, the properties of interest exhibit a rather complex transitional behaviour across the so-called soft boundaries. Traditionally, the modelling exercise is restricted to a consecutive stochastic simulation of distinct geological facies and orebody properties. This results in different zones separated by hard boundaries, ignoring the typical transitional behaviour.This contribution presents an alternative approach which models the entire sand body as a single domain while accounting for the complex trends present. Error curves are used to infer covariance model parameters without the need of a prior removal of the trend. The principle is based on minimising the differences between empirical and theoretical errors resulting from two methods of prediction calculated for different rings of influence. The added value results from the unambiguous decomposition of the spatial variation into a deterministic trend and a stochastic residual. The trend model neither overfits nor underfits the data. The calculated residuals are thus unbiased and the uncertainty can be correctly assessed.The effort results in a characterisation of the resource uncertainty which provides a more realistic image of the spatial variability of the key properties in and across the geological domains of an existing heavy mineral sand deposit.CITATION:Wambeke, T and Benndorf, J, 2014. Optimal inference of modelling parameters to simulate complex trends across soft boundaries – a case study in heavy mineral sands, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 73–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

[Page Minutes 7 Discussion of L. S. Ickis' Paper 20 City Planning and Landscape Architecture for Western Coal Camps, by S. R. DeBoer 22 Discussion of Thos. Foster's Paper 26 Discussion of Safety Committee Report 30 Discussion of R. L. Hair's Paper 52 Discussion of H. I. Smith's Paper 61 Miscellaneous Discussion 62 Discussion of Thos. A. Stroup's Paper 70]

Jan 1, 1924

By L. F. Reinartz

ANOTHER year has rolled by. We are twelve months further away from the start of the depression and. therefore that much nearer to recovery. The accumulated needs and wants 'of our lame, virile population are ready to burst their bonds as soon as confidence returns and credit is stabilized. The steel industry has been harassed by uncertainty of the Government's attitude toward organized labor's de¬mands, and irregularity in volume of production. Steel labor, if left to its own devices, would in most instances, march shoulder to shoulder with the management of steel plants in their effort to pull the industry nut of the ?red.? Cooperation between management and men has improved considerably during; the year.

Jan 1, 1935

By Fraser M. Walsh

The objective of this program was to determine by laboratory experiments the kinetics and mechanics of the reactions that produce acid in coal mine drainage. The program was divided into three phases: In Phase I, five coil mines, representative of Appalachian coal mines, were chosen for sampling and an experimental design was identified suited to accomplish the program objectives. In Phase II, the five mines were sampled and test protocols applied. The results showed most pyrite weathering to be based on oxidation in the presence of water. Iron bacteria, especially Thiobacillus ferrooxidans, catalyzed the rate of pyrite weathering by a factor of three. An increase in initial iron concentration in a system that modeled the nine environment acted to inhibit bacterial catalysis of weathering. In Phase III, five tailings piles were sampled and the material obtained was used to evaluate this method of bacterial catalysis inhibition. The evaluation verified method effectiveness; inhibition of over 80% of the release of weathering products was observed.

Jan 1, 1982

By R. Lee Wooten, David R. Shields, Darren D. Clark

"Borehole permeability tests that measure flow or head changes in boreholes located within seepage barrier walls are commonly used to estimate the in situ permeabilities of those walls for quality control and assurance. The current state of practice for estimating permeabilities from these barrier wall borehole tests is to use equations published by M. J. Hvorslev in 1951. Hvorslev’s borehole test equations model an infinite stratum of uniform permeability, which is not the actual condition for a test performed in a low permeability barrier wall located within a high permeability stratum. We examine and develop alternative equations based on line source analytical models, which more closely match barrier wall test conditions. We describe how these alternate equations can be used to estimate barrier wall permeabilities from borehole tests and compare the results to those obtained from the Hvorslev models. We also provide recommendations that consider differing upstream and downstream water levels.Barrier Wall Permeability Tests - State Of PracticeThe installation of seepage barrier walls has become more common in a variety of applications ranging from dams and levees to contaminated sites requiring retardation of groundwater flow. The types of seepage barrier walls and installation methods include soil-bentonite, soil-cement-bentonite, concrete, self-hardening slurry, geomembranes, and sheet piles, installed with various soil mixing, slurry-supported trench, and driving methods.Owners and contractors have used a variety of methods to evaluate the permeability of these seepage barriers. The following table lists commonly used quality control/assurance tests for evaluating the permeability of a seepage barrier."

Jan 1, 2016

By CIM Mineral Resource, Mineral Reserve Committee

The CIM Mineral Exploration Best Practice Guidelines (the Exploration Guidelines) have been prepared to assist professional geoscientists and engineers to conduct consistently high-quality work in order to maintain public confidence. The Exploration Guidelines are meant to assist professional geoscientists and exploration practitioners in planning, supervising, and executing exploration programs. In Canada, there are generally two types of public resource reporting: “Disclosure”, as defined by NI 43-101, is the reporting of technical information to the public and market participants for securities legislation purposes where a Qualified Person (QP) must be involved, and reporting of exploration information for governmental agencies to support obligations under laws including the Mining Acts of each of the Provinces and Territories. The Exploration Guidelines are also relevant where the results will not be publicly reported but are intended for internal company use. While this document is intended as guidance for work conducted or supervised by geoscientists in Canada, many of the practices described herein can be adapted to mineral exploration activities in other countries. The Exploration Guidelines are not intended to inhibit original thinking, or to prevent the application of new approaches that may develop into fundamental components of successful mineral exploration programs. Rather than provide prescriptive solutions to specific issues, they include general guidelines for current professional practice and to demonstrate and defend the merits of new methods. These guidelines do not preclude individuals and companies from developing more detailed guidelines specific to their own requirements. The initial version of the Exploration Guidelines was prepared by the Canadian Institute of Mining and Metallurgy and Petroleum (CIM) Exploration Best Practices Committee and adopted by CIM Council on August 20, 2000. On January 9, 2018, CIM Council formed a new committee, the Mineral Resources and Reserves Committee (CIM MRMR Committee) with a mandate to, among other things, update the Exploration Best Practice Guidelines. The mandate for the committee was accepted by CIM Council on March 2, 2018. The new document was adopted by the CIM Council on November 23, 2018.

Nov 23, 2018

By S. H. Ash

Probably one of the most significant departures in tunneling practice is the introduction of Diesel locomotives far haulage (Diesel trucks have been used for some time). The fallacy of the belief that they do not generate carbon monoxide or toxic gases and can be used indiscriminately has been proved by the authors through observation for several years of atmospheric conditions surrounding the use of Diesel engines in tunnels. Diesel locomotives haves been introduced in tunnel haulage for reasons other than safety or health. Except to the extent that they replace trolleys, with their danger of causing electrocutions, modern Diesel locomotives do not increase safety Or remove any ordinary hazards to safety or health. In fact, they create such hazards, the extent of which is limited entirely by the carbon monoxide-content level set, method of ventilation, adequacy of the measures.

Jan 1, 1942

By George A. Roberts, Arthur H. Grobe

H. H. Hausner (Sylvania Electric Products Inc., Bayside, N. Y.)—I tested the 18-8 stainless steel powder described by Grobe and Roberts and the results were excellent. The powder was compacted and sintered in purified hydrogen to a very low density (approximately 20 pct and more porosity). Where the other powders show very little ductility when sintered to such a low density, the described stainless steel was surprisingly high in ductility. I would appreciate it if the authors could give us some data on a similar powder but without silicon and also data on 430 stainless steel powder. H. S. Kalish (Sylvania Electric Products lnc., Bay-side, N. Y.)—I should like to verify the excellent results obtained by Grobe and Roberts with their pre-alloyed stainless steel powder. It seems to me, however, that their data are conservative and that even better densities and higher tensile strength can be obtained with these powders by the selection of proper particle size fractions. The accompanying data were obtained by sintering compacts pressed from the powder made by Vanadium-Alloys Steel Co. to 0.8 in. in diam about % in. high in a cylindrical double action die without the use of lubricant. The compacts were sintered for 1 hr at 2370°F in hydrogen purified by passing it through a Deoxo unit (palladium catalyst) and a Lectrodryer. Even the density obtained using the as-received (—100 mesh) compacted at 40 tsi was quite high as was the hardness. This indicates that by increasing the sintering temperature slightly above 2350°F the coining and subsequent secondary sintering operation can be avoided. With the — 325 mesh fraction, however, very much higher density can be obtained and a high hardness. I have no tensile data to present, but I feel that it is not too optimistic to expect. that unusually high tensile strengths and good ductility can be obtained in this sintered material on the basis of the density and hardness data. The sintered stainless steel made by the above-described methods came out of the furnace very bright and clean. The purified hydrogen atmosphere is important in sintering stainless steel to reduce the oxide present in the powder. The result of such a sintering is good densification and good ductility of the sintered product. G. A. Roberts (authors' reply)—We are greatly indebted to Messrs. Hausner and Kalish for their discussions of our paper. Their encouraging remarks are greatly appreciated and their confirmatory data will do much to add to the value of the paper. At the present time it is impossible to provide complete data on a similar stainless steel powder without silicon, but we do know that, in general, the properties are slightly inferior. Data on such a powder and on other stainless steel types are to be published in the near future.

Jan 1, 1952

With IIT research institute as a cosponsor, this seventh mineral waste Utilization Symposium was funded by the Bureau of Mines through its Division of Mineral Resources Technology. Environmental scientists and engineers from five countries (Canada, Netherlands, Austria, England, Guatemala) besides the United States participated in the symposium, which was held Oct. 20-21, 1980, at the Chicago campus of IIT Research Institute. Of the 25 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial waste, and scrap metal, 21 are summarized herein.

Jan 1, 1982