Search Documents

By A. C. Fieldner

In 1927 the Carbonization Committee of the American Gas Association proposed cooperation with the Bureau of Mines in the development of suitable methods for determining the carbonizing properties of American coals. It was further proposed to apply these methods in the testing of representative coals and to make the information obtained available to the public through Government publications. A cooperative agreement was signed whereby the Gas Association contributed part of the funds necessary for beginning the project and appointed a committee to consult and advise the Bureau in the work. The Advisory Committee has been reappointed each year, and the Bureau has had the benefit of its advice. The composition and carbonizing properties of 33 coals previously tested have been given in technical papers of the Bureau of Mines and in short reports published for the most part in the Proceedings of the American Gas Association. A complete list of publications on the work previous to 1937 is appended to this report. The present report gives the composition and carbonizing properties of seven additional coals from West Virginia. The data include results of blending tests in which Beckley led low-volatile coal was used with all the high-volatile coals except the Alma coal, with which Pocahontas No. 4 coal was used.

Jan 1, 1938

By R Aseervatham

The fast tracked mine development strategy attempts to blend feasibility studies and engineering/commissioning functions into a streamlined process. In this compressed process, environmental issues are difficult to control with respect to the optimisation of operational environmental performance. This paper presents a standard mine development process with specific focus on environmental issues, and contrasts this against Rio TintoÆs recent fast track experiences on the Hail Creek project (Australia), the Baranj project (India) and the Gokwe North project (Zimbabwe).

Jan 1, 1999

By L. Tonc

In 2004, the engineers at the Deer Creek Mine located near Huntington, Utah initiated the ventilation planning to exploit a remote area of the mine?s reserves. This area was located under a mountain which would not allow for the incorporation of an additional shaft or portal access near the proposed longwall panels. With this constraint along with the desire to maintain a two entry gate road system and the expected condition of frequent coal wash outs a ventilation plan was established. Different options were examined that included; increasing the current exhaust fan power, adding another exhaust fan installation, converting the ventilation fans in the active portion of the mine to a forcing system, and modifying the ventilation system in the active area of the mine to a push-pull system. The push-pull ventilation system was ultimately selected. This paper details the design process of the ventilation system upgrade, the procurement process for the new fans, and the new fan startup testing.

Jan 1, 2009

By Li Jiuping, Zhong Gang, Chen Yong Zhang, I. Michael Gowring

The Liaoning Dahuofang Reservoir Water Transfer Project is an important development for the Department of Water Resources of Liaoning Province in northeastern China. The 85.3 km water conduit will transport water from the Hun River downstream of the Huanren Reservoir to the outlet on the Suzi River leading to the Dahuofang Reservoir. The additional water is required to sustain the growing cities of Fushun, Shen-yang, Liaoyang, Anshan, Panjin and Yingkou. The project is divided into seven contracts. Three TBM contracts comprise almost 75% of the work and the others are drill and shoot. The focus of this paper is about the creditable TBM performances achieved and some of the problems encountered by Chinese contractors; notably two having had no previous TBM experience.

Jan 1, 2007

By Hui Yongning

This paper presents a simulating test of constitutive relation of soil anchor in laboratory and puts forward a new plastoelastic mechanical model, on which a new calculating formula of elastic and plastic limit bearing capacity for soil anchor is suggested and two engineering projects verify that this method is adaptable.

Jan 1, 1991

By Don Peel

Mineral aggregate, the most widely used mineral resource globally, has attracted little academic or public interest. Of all mining developments, the aggregate resource is seldom factored into resource management decisions. This lack of recognition to the strategic aggregate resource has significant economic, environmental, and social implications. Impact to the economics, the environment, and the community coincide with the key elements of the United Nations concept of ?sustainable development?. To build on the concept, the mining sector contracted the International Institute for Environment and Development to assess how mining activity contributes to sustainability. As a result, a useful assessment process was developed by the Mining, Minerals and Sustainable Development (MMSD) Task Group entitled ?Seven Questions to Sustainability: How to Assess the Contribution of Mining and Mineral Activities.? In Alberta, recent opposition to mineral resource development by community residents offers an opportunity to employ the MMSD?s assessment procedure. The public opposition to the mining activity was addressed through a stakeholder planning process initiated by the municipal council of Sturgeon County, Alberta. As a result the Calahoo/Villeneuve Area Structure Plan (CASP) was formulated and adopted. To measure the effectiveness of the CASP planning process in terms of sustainability, this paper applies the MMSD?s Seven Question assessment to the Calahoo/Villeneuve Area Structure Plan.

May 1, 2004

By Gordon T. Austin

The combined production value of natural abrasives, which consist of tripoli, special silica stone, garnet, and emery, decreased in 1986. Shipments of processed tripoli increased slightly in quantity and 20% in value. Production of garnet, a common iron- aluminum-silicate mineral, decreased 12% in quantity and value. There was a 4% increase in the quantity and an 11% increase in the value of refined garnet shipped when compared with 1985 shipments, a new record high. Production of crude special silica stone decreased 7% in quantity and slightly in value, and shipments of finished special silica stone products decreased slightly in quantity and increased 229% in value. Production of emery, an impure aluminum oxide, increased 77% in quantity and increased 269% in value of product mined and shipped. [ ]

Jan 1, 1988

"Automatic flotation control in varying degrees of sophistication is practiced at a number of concentrators throughout the world. Practically, the variable conditions in the flotation circuit and the difficulty in maintaining accurate instrumentation information all add to the complexity of automatic control.Further development at the Kidd Creek concentrator has resulted in a 3075 mtpd copper flotation circuit capable of running twenty-four hours a day under the direct control of an optimizing supervisory computer.Three main streams, continuously monitored by an XRF analyser, supply circuit information to the optimizing computer. Circuit efficiency calculations (from smelter contract terms) and target setpoints allow the computer to determine the economic optimum direction to move the circuit based on the grade/recovery relationship. Circuit manipulation is accomplished by precise pumping of collector and frother reaqents together with accurate control of flotation bank pulp levels. The former uses computer controlled diaphragm pumps and the latter is achieved by control loops utilizing a float type level transmitter, variable position dart plugs and a process computer working to setpoints determined by the optimizing computer.The development of a fully automated flotation circuit is by no means complete, but increased knowledge and major hardware improvements have allowed its progression to a higher level of sophistication."

Jan 1, 1983

By R. J. Wensley

THE use of small substations for the supplying of 275-volt energy to the locomotive and cutting machines in coal mines is a well-established practice. A few years ago, when labor costs were lower, these substations were located as near to the load as possible, and an operator was provided for each station. This practice has now become so expensive that substations are being located with reference to other mining machinery, such as hoists or pumps, so that one operator can look after both. Some-times the substation is operated by one whose duties make him traverse quite a large area. In such cases the interruption of alternating-current supply may produce a long interruption in the direct current, as the station cannot resume service until this man reaches it. Such interruptions interfere seriously with production and may easily counterbalance the supposed saving gained by such operating methods. The grouping of substations for convenience in operating may also result in excessive copper loss and consequently poor trolley voltage, with its attendant evils of low locomotive speeds and increased locomotive motor maintenance. The speed of the coal-cutting machines will also be reduced. By relieving the substation of its, burden of the operating labor cost, the most economical location, from an electrical standpoint, may be chosen. The matter of machine insurance should also be considered. If an attendant is caring for several kinds of equipment, he cannot watch the machine continually for signs of trouble; therefore, continued overload, phase failure, low alternating-current voltage, bearing trouble, etc. may result. Some partly automatic equipments have been installed; these have protection against low voltage, reverse current, and bearing trouble and are provided with automatic reclosing circuit breakers. This is a step in the right direction but it does not go far enough to give first-class machine insurance.

Jan 9, 1921

By Leons Kovisars

Introduction Labor is the major cost element for most mining operations. Labor costs are continually increasing, both in nominal and constant terms. This is true in developed as well as less developed countries. There are two ways to control unit labor costs - labor costs per ton of ore mined. Replace labor with capital (increased mechanization) or improve productivity (reduce the labor force). Every miner is aware of specific inefficiencies at his or her particular operation. But the miner has no comparative measurement standards. So it is difficult to know whether these inefficiencies are major or minor. The miner may also be unaware of large-scale inefficiencies because ongoing labor practices may have caused management complacency. Met Research studied mining labor productivity. The firm collected pilot data by sending direct-mail questionnaires to 320 nonferrous mining operations around the world. The response rate was 27%, of which 78 operations provided full data on production and employment.

Jan 11, 1983

By J J. McEwan

Silver tarnishes readily in common atmospheres and is accelerated in humid atmospheres. Tarnish is the formation of silver sulphide on the surface of silver when it is exposed to a wide range of sulphur-containing atmospheres. Tarnish is unattractive and highly undesirable, and can be removed either with a silver polish or a chemical dip. Dips are generally only recommended when heavy black tarnish cannot be removed with a polish, and care must be taken during cleaning because these can contain aggressive chemicals and give off hazardous and unpleasant smelling fumes. Polishes work best for large areas of plain undecorated silver, and form part of a regular cleaning programme. Some polishes contain chemicals that inhibit tarnishing, but these generally only have a short life. Several methods have been developed to reduce tarnish formation on Silver; these include alloying, surface treatment, and coatings. The authors evaluated a range of self-assembled monolayer (SAM) surface treatments and coatings in earlier research. Four treatments/coatings increased the time to noticeable tarnish by more than ten fold, and the results were reported at the International Corrosion Congress (ICC) in 2005, and at the Mint Directors Conference (MDC) in 2006. SAM treatment using 95% 1-hexadecanethiol (C16H34S) was found to give good anti-tarnish performance and showed potential for the commercial treatment of Sterling silver. Therefore research was performed to optimise the methods of application of this type of coating to provide an easier, faster, and more-user friendly technique to provide an anti-tarnish treatment. Keywords: silver, tarnish resistant coatings.

Jan 1, 2006

By John E. Rourke, O&apos

This report documents the process of site selection, instrument installation, data acquisition, and preliminary data analysis followed to characterize the physical response of overlying strata to longwall mining. A system of surface, subsurface and mine level instrumentation was installed at the Allen Mine in Weston, Colorado where the overburden varied in thickness from 600 to 900 feet. Survey monuments, automatic-recording strain-meters, multi-point rod extensometers, inclinometer-extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. A preliminary analysis of the data acquired up until project termination has shown the system to be operative and strata response to be similar to that reported for other subsidence monitoring case histories. Recommendations for continued monitoring of the instrumentation systems are presented.

Jan 1, 1982

By D. Randolph Berry

The objective of this program was to develop a system to extinguish coal mine fires by remote sealing of the underground passageways. The system developed had to be versatile enough to function under a wide range of operating conditions, including large variations in passageway geometry, depth of mine, water conditions, both in the mine and at the surface, and rubble in the mine passage. The system developed had to include instrumentation for the remote probing of the passageway prior to sealing, a system for sealing the mine passages, and instrumentation for remote monitoring of the quality of the seal during and after construction. These objectives were successfully achieved during this program. The remote mine sealing capability of the system was satisfactorily demonstrated in a field test conducted at the Eastern Associated Coal Corporation Federal No, 1 Mine in Grant Town, West Virginia.

Jan 1, 1973

By Murali Gadde

Design of underground excavations in coal mines involves two major tasks: estimation of stresses and determination of rock mass strength. Owing to the complicated nature of rock mass, progress in its strength determination has lagged significantly compared to advancements in stress analysis techniques. Also, because of the impracticality of conducting field-scale strength tests, experimental approaches have very limited applicability in estimating rock mass strength. As a result, many empirical rock failure criteria have been developed based on observed performance of in situ rock structures. Unfortunately, all the popular rock mass strength criteria are based on data from large-scale ?isotropic? non-coal structures and thus can not be directly applied to coal mines. In this paper, an attempt has been made to adopt the popular Hoek-Brown (H-B) criterion for use with coal measure rocks. First, the H-B criterion is examined against laboratory triaxial strength data for different types of coal measure rocks. Then, procedures to estimate the H-B rock mass strength parameters relevant to coal measure rocks are suggested. Finally, a case-study has been given to show the usefulness of the proposed strength estimation approach.

Jan 1, 2007

By R. J. Snoby, J. K. Alderman

Although once fairly common as a method of coal preparation in the United States, dry cleaning has virtually disappeared. Low-rank coals used for power generation in the western U.S. are suited for dry cleaning because water has limited availability in the American west. Surface moisture added through wet cleaning offsets energy improvement achieved from mineral matter reduction. Information will be presented on the commercial application of dry cleaning in North America, the historic development and current status of the technology, and the introduction of modern processing theory and control technology to the design of dry cleaning equipment and plants.

Jan 1, 2001

Geophysical methods are useful non-invasive means of collecting subsurface information on the environmental impacts of resource developments. Techniques such as seismic refraction, ground probing radar and magnetics are well established tools for environmental studies of waste disposal sites. Repeat resistivity surveys, gravity surveys, and infrared or multispectral remote sensing hold great promise for monitoring environmental changes. Examples from New Zealand include geothermal field monitoring, which may involve the use of geophysics for .detecting changes of surface thermal activity, hydrothermal eruptions, induced earthquakes, contamination or depletion of shallow groundwater, and subsurface fluid recharge. Other examples include resistivity monitoring of contained effluent disposal ponds, tailings dams and landfills. Experience has shown that care is necessary to identify the natural variability of the parameter measured before drawing conclusions regarding an observed change.

Jan 1, 1994

By R. A. Bosch, F. V. Lenel, G. S. Ansell

RECENTLY, Ansell and aenel' proposed a dislocation model to account for the yielding behavior of dispersion-strengthened alloys. The criterion for yielding used in this model was that yielding occurs when the shear stress due to arrays of piled-up dislocations fractures or plastically deforms the dispersed second-phase particles. Calculations based on this model predict that the yield strength, uysof a dispersion-strengthened alloy containing particles whose geometry permits them to be considered as straight, i.e. not curved, barriers to dislocations follows the relation where and are the shear moduli of the matrix and dispersed phase respectively, b is the Burger vector of a dislocation in the matrix, A is the mean free path between dispersed phase particles and C is a constant. This yield stress, ys, is closely approximated in polycrystalline alloys by the proportional limit. The offset yield stress, uoy, is the yield stress, uys, plus the increase of stress due to strain hardening in the offset strain increment. Previous investigation1 has shown that Eq. [I] describes the yielding behavior of several different dispersion-strengthened alloys as a function of the mean free path between dispersed phase particles at a constant temperature. The purpose of this investigation was to investigate the temperature dependence of the yielding behavior of dispersion-strengthened alloys. The alloys studied, MD2100 and MD5100, are SAP-type alloys containing flake shaped aluminum oxide particles dispersed in a matrix of commercial purity aluminum. The proportional limit and 0.2 pct offset stress of both of these alloys were determined as a function of temperature over the temperature range from -190" to 500 C. All tests were conducted on an Instron tensile testing machine. Stress was measured by means of the Instron load cell. Strain was measured by means of SR-4 strain gages attached to the tensile specimens. Stress sensitivity was 80 psi. Strain sensitivity was 2 x 10F Fig. 1 shows the values received for the proportional limit and 0.2 pct offset yield stress plotted as a function of homologous temperature for both the MD2100 and MD5100 alloys. Inspection of Eq. [I] shows that of the terms which determine the theoretically predicted yield stress, uy,, only the shear moduli have an appreciable temperature dependence. From Eq. [I] the yield stress at any temperature T, UT, may be predicted from the yield stress at any arbitrary reference temperature, in this case 25 OC, u25, by the relation where the subscripts T and 25 refer to the values of the property at test temperature and at 25"C, respectively. The temperature dependence of the yield stress predicted by Eq. 121, based on the observed value for the proportional limit at 25OC, is also shown in Fig. 1. In evaluating Eq. [2] the following data was used. The values for the shear modulus of

Jan 1, 1962

A paper presenting an overview of legislative and best practice approaches to the management of OHS&E and business risk for Australian tunnelling operations. Best practice can be achieved in Australian tunnelling through ærisk awarenessÆ by decision-makers and line personnel. This will identify problems before they occur and lead to implementing controls appropriate to avoiding loss throughout the life cycle of the underground opening. The author draws on legislative approaches from all Australian states together with practical experience from risk management and risk engineering work from six recent tunnelling projects. This describes a process that:commences with concept risk assessment,involves quantification of major hazards,conducts assessments of operating risks, andleads to implementation of an integrated management system that keeps construction activities connected with the controls identified in the design and planning phases and minimises the losses sustained as a result. Key points addressed include:where the industry is going with respect to risk û methods and considerations,how tunnelling risks are perceived by the industry and legislation,how tunnel constructors and owners can minimise exposure by using proper risk engineering ætoolsÆ, andreflections on best practice methods for transferring knowledge from designers to contractors/operators.

Jan 1, 2008

[RESULTS OF THE PRIMARY CONVENTIONAL PERFORMANCE AND COST MODEL OF THE UNIT OPERATIONS OF UNDERGROUND PERCUSSIVE DRILLING AND BLASTING]

Jan 1, 1977

By Roger L. King

Working in gassy ground conditions is an everyday occurrence for the U.S. coal mining industry. As tunneling operators begin to venture into projects that expose them to the additional hazard of potentially explosive atmospheres, lessons learned by the mining industry over years of experience should be transferred into this industry. This paper will present practices developed by the U.S. coal mining industry for dealing with the problem of excavating material in potentially explosive atmospheres. Procedures will be discussed that can be used to detect and quantify gas prior to mining that have application to the construction industry. Degasification or drainage practices, including predrainage from vertical and horizontal boreholes, will be discussed. Also, ventilation practices commonly used in the mining industry will be presented.

Jan 1, 1985