Search Documents

By Helmut Hass, Marco Ziller

"Abstract: 1 Sophia Spoortunnel Marco Ziller, Trevi S.p.A.:For the construction of 14 cross passages connecting the twin tunnels of the Sophiaspoortunnel the Artificial Ground Freezing technique was applied as temporary soil improvement. AGF by Brine and Liquid Nitrogen was implemented. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil during the freezing intervention in order to control the behaviour and the efficacy of the treatment.IntroductionThe Sophia rail tunnel is a bored tunnel with a length of 4.24 km, comprising two separate parallel tubes with an outside diameter of 9.45 m. The twin tunnels were excavated by a TBM equipped with hydroshield. Seven service shafts, approximately 30 m deep, were constructed in between the tunnels. From each shaft two cross passages were constructed connecting the shaft with both tubes, for a total of 14 cross passages.The Artificial Ground Freezing technique utilizing both the Brine and Liquid Nitrogen methods was used for temporary waterproofing and soil support to allow the excavation of the cross passages. The natural soil to be frozen was consisting in loose sand and clay under a hydrostatic pressure up to 250 kPa.For the measurement of the ground temperature. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil and at the contact with the tunnel lining. Furthermore, a comprehensive computerized system of sensors and cryogenic valves was designed and implemented in order to manage the whole Nitrogen process.Soil Main CharacteristicsThe soil stratigraphy is generally consisting in Clay (Holocene) from ground level to -15 m depth, followed by Pleistocenic Sand, from -15 to -25 m, and Clay below -25 m."

Jan 1, 2014

By H. V. Makar

Laboratory tests were performed to obtain a quantitative description of the effectiveness of sodium sulfate (Na2SO4) for removing copper from molten iron and to determine the effectiveness of Na2SO4 on actual auto scrap. The tests were conducted on induction melted heats of iron averaging 0.58 and 1.50 percent initial copper and on cupola-melted auto scrap containing 0.45 percent initial copper. The Na2SO4 was added in powder form in amounts ranging from 2.9 to 43.8 percent of the weight of iron being treated. The data showed that copper removal for the various Na2SO4 treatments followed a similar trend, regardless of the iron composition that was tested. The equation Y = 1 - e-3.23x approximately reflects the relationship between copper removal and amount of Na2SO4 added, where Y is the fraction of copper removed and x is the ratio of the weight of Na2SO4 added to the weight of metal treated. Copper removals ranged from 3.3 to 74.5 percent and reductions down to less than 0.10 percent final copper were achieved in the auto scrap. Copper removals were generally accompanied by sulfur removal, and initial sulfur contents ranging from 0.10 to 0.20 percent were reduced to as low as 0.02 percent. High temperatures and long slag reaction times tended to induce copper and sulfur reversion from the slag, but, generally, the Na2SO4 treat¬ments were effective up to approximately 2,820° F with reaction times not exceeding 7 minutes.

Jan 1, 1968

By Cawte D. C, Just G. D, Whitchurch K. D

The stringent marketing specifications included in coal contracts mean that coal producers must supply cleaner and more consistent coal than may have been formerly required. Geostatistics has the potential to aid in the accurate estimation of the washability characteristics of coal. A prediction method, the Kriged Service Variable Approach has been developed.A Computer Aided Drafting and Design system has proved useful in the development and application of the approach. The geostatistical approach has been tested against coal geological and borehole data and applications discussed.

Jan 1, 1987

By J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

"The Niobec concentrator rejects up to /5% of the Nb as slimes (-10u.m). The recovery of Nb from these slimes by column flotation is being studied. An essential condition for selective flotation is slimes dispersion. A particle size analyzer, the Sedigraph 5000D, was used to monitor dispersion in plant waters with combinations of organic and inorganic dispersants and flotation reagents. Flotation reagents were particularly detrimental to dispersion with sodium silicate. The best dispersion conditions were selected for column flotation tests. These tests revealed that reagent combination had a pronounced effect on froth stability. Careful frother selection achieved good froth stability under conditions of good dispersion. Plant water increased the required dispersant concentration causing mineral depression.IntroductionSlimes (-10 u.m) rejected at Niobec contain up to 15070 of the over-all Nb content . Recovery of Nb from these slimes would significantly increase over-all recovery. A suggested recovery route involves two phases: (1) carbonate flotation (to remove most of the carbonates) depressing silicates and pyrochlore (as currently done at Niobec); and (2) selective (direct) pyrochlore flotation from the silicates. Phase 2 has been addressed and several routes to achieve selective flotation are available. Phase I was attempted with the selective reagent scheme used at Niobec but a considerable amount of pyrochlore floated with the carbonates due to poor slimes dispersion."

Jan 1, 1987

The zinc-lead lode at Rosebery, on the West coast of Tasmania, has a total length of over 4000 ft. It consists of five elongated lenses parallel to the foliation planes of the quartz sericite schist, and is situated at the junction of the quartz sericite schist and a thin belt of slate. The lenses consist of massive, fine grained sulphide ore, with small amounts of quartz, barite, sericite and chlorite, and they terminate in masses of low grade ore. The gangue minerals increase in quantity in the low grade ore which includes small quantities of the manganese garnet, spessartite. The schist walls of the lenses are in places impregnated with lode minerals to a degree sufficient to permit them to be regarded as economic ore.The ore-bodies have developed from incoming mineral solutions by the replacement of the quartz sericite schist and are localised where the ore solutions have been confined by a relatively impervious slate band. The early stages of replacement of the schists are signified by the development of pyritic bands which are succeeded by a strong development of zinc blende. With ptogressive crystallisation, the character of the mineral solutions gradually changed and the development of galena, and its associated bournonite, became more important in the later stages.Remnants of the replaced schist, in the form of isolated wisps and schlieren of sericite and chlorite, are present in the ore body, more noticeably in the pyritic specimens. An important feature of the ore is the association of small ogllantities of gold with trahedrite.

Jan 1, 1934

By C Bellia, A Maldonado, S Strong, H Baxter

This paper discusses the technical and cost benefits of alternative data collection techniques used to collect lithological information, obtain laboratory testing samples and perform in situ testing. A comparison between diamond coring and sonic coring techniques is made using data from a recent geotechnical investigation for a final pit slope cut-back. The impacts of the coring method on laboratory strength testing results, material character testing and, ultimately, the mass strength parameters and subsequent slope design adopted are compared. The sonic coring method was chosen out of necessity and enabled the collection of tube samples of a clay unit of interest as well as bulk samples for material character and geochemical testing. The sonic coring generated unexpected degradation of clastic units, while cohesive clay-dominated units were recovered well. The likelihood that disturbance due to the coring method would result in lower than expected triaxial strength results was recognised ahead of time, with surplus samples collected and single-stage triaxial strength testing undertaken. This testing compared favourably with historic three-stage testing, where sample degradation occurred during the later stages. Material character testing of fine-grained, clay-dominated units was comparable with historic diamond core testing, while grain size estimates for more clastic units tended to be finer than previous results. The use of sonic coring over non-cored methods enabled the collection of material texture data, geotechnical properties and a full suite of geochemical analyses. This provided a comprehensive understanding of the lithological and geotechnical character of the rock and soil mass. A high-confidence geotechnical model was developed. The end result was the development of a slope design that was more aggressive than was previously designed (5° steeper inter-ramp angle), which has proven to be appropriate to the conditions following excavation. Overall, sonic coring was a cost-effective means of obtaining additional geotechnical data for the site.CITATION:Baxter, H, Bellia, C, Maldonado, A and Strong, S, 2015. Case study assessing alternative data collection techniques and analysis methods to assist with geotechnical slope design, in Proceedings Iron Ore 2015, pp 419–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By William Brundan

INTRODUCTION The Srisailam Left Bank Canal (SLBC) Tunnel Scheme is part of the Alimineti Madhava Reddy Project in Andhra Pradesh, South India. This scheme has been planned since 1983 and will provide irrigation facilities to drought-ridden areas in Andhra Pradesh. Water will be transferred from the Srisailam Reservoir during the monsoon months to 0.3 million acres of farmland and will also provide drinking water to villages en-route. The paper will address the design and onsite assembly of the Robbins Double Shield TBMs for Tunnel-1 of the SLBC tunnel scheme from planning to start-up of the machines. Also, it will provide a current status of the project and describe the advantages of a site assembly. Problems encountered to date and the solutions adopted will also be described. The project comprises over 50 km of tunnels and involves construction of the world?s longest tunnel without intermediate access. The TBM tunnels at 43.9 km in length and 10.0 m diameter will cross the Amrabad plateau, containing a wild life sanctuary and India?s largest tiger reserve, the Rajiv Gandhi. Jaiprakash elected to excavate the tunnel using two tunnel boring machines, rather than by drill and blast, in order to alleviate surface disturbances to environment and the tiger reserve, wild life sanctuary, and protected forestry areas. The Project was awarded to the Main Contractor Jaiprakash Associates Ltd with The Robbins Company as the Tunnel Boring Machine (TBM) supplier in August 2005. The Robbins Company supplied the TBMs along with two continuous conveyor systems and all spares and consumables to complete the tunnel excavation.

By T. Bertke

This document assesses the environmental aspects of a preliminary design for processing kaolin clay as the domestic resource for recovery of alumina by a hydrochloric acid leach-HCl gas induced crystallization process. The report covers waste sources, control measures, and potential environmental and health effects applicable to the process technology.

Jan 1, 1980

By O. T. Barrett, R. F. Aberethy, H. N. Cooper, Thomas Fraer, William L. Crentz

"INTRODUCTION The object of the techniques described in this report is to determine the possibilities of separating the components of a raw coal into such grades as may be necessary to recover some exceptionally clean functions for special purposes.To do this commercial gravity methods would require separation at very low specific gravities, entirely outside the range of conventional practice. Hence, a technique has been developed for breaking down cool ample, into very close fractions within the gravity range of the (-lean coal matter as well as for separating it from the refuse and particles.Such data on the fundamental specific-gravity consist of the clean-coal matter will serve to appraise the difficulty of the problem and to chow be accomplished if and when effective methods of making such separations commercially are developed."

May 1, 1945

By Wolfgang Van Hooff

Encouraged by a strongly growing and evolving market for granulated products, Paul Wurth continuously improves its granulation and dewatering technologies to provide customers with state of the art installations. Continuously developed know-how about the granulation process of iron blast furnace slag enabled application to non-ferrous materials such as Ni-Slag, Pb-Slag, Blister Copper, Cu-Matte and even TiO2-Slag, which rank among the most difficult materials to granulate. This paper identifies how critical objectives in granulation and dewatering technologies applied to different molten materials with respect to various product quality objectives can be addressed. The differences between hot and cold water granulation systems are explained, including the step from cold runner to granulation water tank. Development of a flow and pressure controlled blowing box is the latest step to optimize the granulation process in order to meet the latest standards in terms of quality, power consumption and environmental protection.

Jan 1, 2006

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

"The work in the paper introduces a 2-dimensional finite element model for analyzing particular material processing in a roller press. Two basic roller geometries are considered: (a) smooth rolls (used for milling and compaction) and (b) rolls with cavities, commonly used for briquetting. A model is presented that is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables.MODEL, RESULTS AND CONCLUSIONSAn associated Gurson model was employed as a constitutive model for the material. The calibration of the model was based on experimental results from an instrumented compaction die. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Powder River Basin sub bituminous coal fines with moisture content 9% was used as a model material.Two finite element models have been set up, one for the briquetting roll and one for the “equivalent” flat roll. Approximately 3200 plain strain continuum elements with reduced integration (CPE4R) were used. Lagrangian-Eulerian (ALE) approach in conjunction with judiciously applied remeshing was employed with the commercially-available, dynamic explicit version of ABAQUS finite element code.Comparison of model predictions with experiment shows that there is an agreement in terms of the general trends of experimental values recorded on laboratory roller presses. Gurson model overpredicts stresses at low densities and, as a consequence, overpredicts roll force and roll torque."

Jan 1, 2003

By William N. Patterson

This report describes the design and testing of an improved quiet hard rock percussion drill. The improved drill incorporates a tappetless design with independent rotation in a hand held drill weighing 50 lbm. Laboratory and field testing in three mines were conducted. The testing showed improved drilling performance with no increase in measured noise levels over the fist design.

Jan 1, 1985

By Michael P. Balducci

Urban deep foundation projects contain unique risks that must be recognized by the parties involved. Common pitfalls must be recognized and avoided or addressed through contractual relations and corresponding insurance coverage. By understanding these pitfalls, examining the risk-apportioning clauses and corresponding insurance obligations, may the parties? desires and expectations be met.

Jan 1, 2008

By Donald P. Schlick

This Information Circular presents a brief historical digest of the early attempts of the Bureau of Nines and the U.S. Public Health Service to establish coal mine dust exposure standards. It reviews current, accepted standards of the United States as well as available standards of other countries.

Jan 1, 1971

For the use of those who prefer manila rope to wire rope for light hoisting and hauling, the Ingersoll-Rand Co. has brought out a new model Little Tugger Hoist which is designated No. 11. The square piston, reversible driving engine, automatic lubrication, inclosed gearing, rum release clutch and worm-operated band brake are essentially the same as in the No. 1 model which was introduced about two Years ago. The main differences are in the diameter and length of the drum, the width of the flanges and, necessarily, the main frame and overall dimensions. The new No. 11 Little Tugger has a hoisting drum 7 in. in diameter by 17 in. long with 5-in. flanges. This accommodates 300 ft. of 7/8 -in. manila, rope. The maximum capacity of this hoist is conservatively rated at 600 1b. The weight of the hoist itself is 358 lb. It is 21 ½ in. long, 31 ¼ in. wide and 23 in. high.

Jan 12, 1916

By L. Lacerda, C. Rose, E. Zellers

Approximately six hundred air sample measurements were taken at several U.S. underground metal/nonmetal mines in 1998 and 1999. This air sampling effort was organized by the Nevada Mining Association to evaluate mining conditions and to evaluate the Mine Safety and Health Administration’s (MSHA) Proposed Rule on Diesel Particulate Matter Exposure of Underground Metal and Non-metal Miners. MSHA’s proposed air sampling method, NIOSH Method 5040, was tested under controlled conditions and under normal mining conditions. Unfortunately, NvMA sampling results have indicated that carbonaceous rock dust, oil mists and even cigarette smoking create severe sampling interference problems for NIOSH 5040.The main conclusion was that NIOSH 5040 did not distinguish between DPM and other airborne carbon particulate. Thus, it is not a reliable method of accurately and unequivocally measuring DPM in underground metal/nonmetal mines.

Jan 1, 2000

Smarter Gravity Separation Using the Kelsey Centrifugal Jig With relatively coarse grained and easy-to-process ore sources rapidly dwindling, smarter techniques are becoming more necessary for the continued success of mineral processing operations, while increasing environmental pressures also require more environmentally friendly solutions. Gravity concentration has long been employed to pre-concentrate minerals using water, reducing or eliminating the need for less environmentally friendly processing techniques such as flotation. Conventional gravity recovery devices however, operate in a 1 g environment with limited efficiency in the separation of fine particles of heavy and gangue minerals. More recently developed centrifugal concentrators operate in a multi-g environment and enable finer heavy minerals to be recovered, but also exhibit limited separation efficiency due to the separations being based on solid particle mass differentials. Further enhancement of gravity separation has been achieved using the Kelsey Centrifugal Jig (KCJ), which also operates in a multi-g environment, but separates minerals on the basis of specific gravity differentials, using 'ragging' media and a pulsation mechanism, which maximises the effect of differential particle accelerations. This enables the efficient separation/recovery of minerals down to a particle size of ~6 ¦m and/or separation of minerals with a low specific gravity differential. This paper presents details on the principals of operation of the KCJ, recent improvements in the technology and recent developments in modular KCJ plants, as well as some KCJ application areas, which offer smarter, environmentally friendly processing opportunities for the mineral processing industry.

Sep 13, 2010

By Brandon Fryman, Josh Hoffman, Rhys Baker

A post-detonation debris collection project was led in conjunction with a large ammonium nitrate(AN) railcar detonation conducted by the Department of Homeland Security-Transportation Security Administration, Department of Defense-Combating Terrorism Technical Support Office, Sandia National Laboratories, and the U.S. Army Dugway Proving Grounds. This important work will aid in underpinning algorithms used in a Quantitative Risk Assessment (QRA) tool. The test also provided valuable data about the effects and consequences following an AN detonation. The test took place at the Utah Dugway Proving Grounds on April 27, 2018 and the debris collection was conducted the following two weeks with an average of 20 persons per day and an approximate total of 1,400 manhours. A paper was presented at the 2019 ISEE Conference on the collection efforts, challenges, and lessons learned. A complete data analysis effort was completed on the test data in 2019 that resulted in updates to the QRA Railcar Potential Explosion Site (PES)model and AN engine. The analysis included an assessment of the debris data resulting from the Derailed test. This paper is meant to serve as a summary of the analysis effort and findings and as an update to the previously presented lessons learned from the debris collection and analysis effort.

By D. E. Stephenson. Discussion by R. G. K. Morrison, L. Obert

R. G. K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que., Canada) - The discing of drill core has been a recognized pressure phenomenon for many years but only recently has an interest been taken in the mechanism involved. The work of Jaeger and Cook is referred to in the text. The authors have now advanced the study to establish, within certain loading limitations, a direct relationship between axial and radial stress at failure. This is an important contribution. In mines generally, where pressure conditions result in the spalling of openings, the faces of drifts and crosscuts, on scaling, usually show a concavity with respect to the opening very similar to the face of the drill hole after the separation of the stub. The same holds for shaft sinks. This suggests a similarity between the mechanism of the discing of core and that of the spalling of an opening, under pressure, to develop a more stable outline. The latter, commonly regarded as shear, is the most conspicuous type of failure observed in

Jan 1, 1967

CSIRO Mineral has recently developed a new electron microprobe based system for characterizing zircon grains from heavy minerals sand deposits. The system acquires cathodoluminescence (CL) spectra, X-ray and backscattered electron (BSE) signals in parallel. By scanning over a specified target area, CL wavelength and X-ray element distribution maps of polished zircon grains can be acquired. Post-inspection of the combined dataset using in-house developed software enables correlations between chemistry and structure to be investigated. The new method offers significant benefits over traditional CL and BSE techniques in that direct comparison with the elemental concentrations over the same region is now achievable. By combining the electron microprobe results with data for the same mapped region obtained via a nuclear microprobe, significantly better detection limits (~ 1ppb) for elements with atomic numbers greater than iron are possible. The ability to measure spatially related analytical data and then investigate the correlation of the CL spectra with chemical data is an important advancement in the characterization of zircons. Key words: zircon, characterization, cathodoluminescence, backscattered electron, electron microprobe, nuclear microprobe, chimage, proton induced x-ray emission.

Jan 1, 2003