Search Documents

By R. O. Dannenberg

The Bureau of Mines conducted laboratory batch and small-scale continuous tests to remove traces of dissolved molybdenum from water simulating waste discharged from a molybdenum concentrator, Molybdenum concentrations, initially ranging from 2 to 10 ppm, were decreased to 0.5 ppm or less by coprecipitation of the molybdenum with freshly precipitated ferric hydroxide" The precipitate was separated as a froth by dissolved-air flotation for subsequent disposal. Although the treated water met current environmental standards for contained molybdenum, contained particulate iron might have to be removed by filtration for the water to be acceptable. Estimated costs for treating concentrator effluent water were 55 cents, 57 cents, and 64 cents per 1,000 gal at initial molybdenum concentrations of 2, 4, and 10 ppm, respectively.

Jan 1, 1982

By Gilbert L. Forst

The objective of this program is to identify and evaluate superior, lightweight substitutes for selected coal mine roof support concepts such as crossbars, posts, and crib blocks. Engineering analysis and concept design identified, through tradeoff studies, that some materials are promising, from a technical standpoint, as support substitutes: E-glass reinforced polyester resin, high strength low alloy steel, aluminum, and very high early strength (VHE) cement. An economic analysis indicates that none of the lightweight substitutes are economically competitive with wood on an initial cost basis; however, in terms of life cycle costs based on current dollars, the high strength low alloy steel appears competitive for crossbars, and the VHE cement and E-glass/resin appear competitive for posts.

Jan 1, 1978

By R. J. MacLeod

"INTRODUCTIONThe removal of water or liquid from slurries and solutions is a procedure generally present in many process industries. This has prompted the development of many mechanical and thermal devices with which, I have no doubt you are al1 familiar.In the mining industry, beneficiation of ores necessitates ' the removal of water or other 1iquid from the concentrate material. The most common method of accomplishing this is by means of thickeners, vacuum filters and rotary dryers, generally all three and in that order;The use of spray drying techniques to obtain the same end has many advantages and these will be outlined here.THE PRINCIPLE OF SPRAY DRYINGA Spray Dryer consists of a cyclone shaped chamber where hot air and atomized concentrate are introduced in the upper section. (Sec figure No. 1). Efficient mixing of these two streams produce dry concentrate and moist spent air, both of which are removed from the base of the chamber.Thermal dewatering involves the product ion of heat and spray drying has no special requirements in this area. Generally a direct fired air heater is used and the products of combustion whether they stem from the use of gas, oil or coal fuel go into the spray dryer along with quench or dilution air which is used to reduce the combustion gases to the desired temperature. This generally lies in the range of 1,000 to 1,600° F. In spite of these relatively high inlet temperatures, the spray drying process eliminates the need for refractory lining or indeed any special heat resistant metals except on the air inlet ducting. Waste heat may also be used even if a significant amount of contamination is present."

Jan 1, 1972

By Rudolf E. Greuer

Every mine contains inflammable materials, either in form of the minerals mined or in the form of brought-in supplies. Although great efforts are made to make mines as far as possible fireproof and to prevent ignition sources, the possibility of mine fires, like that of other accidents, will always continue to exist. Detailed statistics are available for coal mines. They show (65,112) that the number of major mine fires in the USA over the last 20 years has remained more or less constant with approximately 50 per year. The same number is reported (26) for the British coal mines. Other countries (147) report about 1 major fire for every 10 million tons of coal production. Conflicting data are published on the number of fatalities caused by fires, presumably because frequently deviating opinions on the cause of death exist. On the average (82,99) 4 miners are killed per year in the US and in the British coal mines. Although this number is much smaller than that for several other causes of fatalities, one must keep in mind that almost every small fire can develop into a large disaster.

Jan 1, 1973

By D. J. Leidel

The offshore production of oil and gas resources has been active in the Gulf of Mexico since Kerr- McGee drilled the first commercial well out of the sight of land in 1947. Since then, approximately 60% of the offshore oil/gas production structures used globally have been erected in the GOM to support the production of energy resources’. The shallow, shelf and shelf edge waters of the Gulf of Mexico have reached or are rapidly approaching production maturity, requiring that the fixed structures used to support energy production be removed or otherwise disposed of by suitable means. The use of energetic materials has been determined to be a safe, efficient and cost effective technology to remove fixed offshore structures whose service life has been exceeded.

Jan 1, 2002

This paper provides an overview of possible approaches for structuring the ventilation systems for mines that will become operational within the next decade. Features addressed in the paper include: aspects of airway design and layout in the absence of centralized vertical return shafts, the impact of using diesel-powered trackless equipment in conjunction with conveyor belts in the development and production phases of the project, and the need to balance increasing electrical power costs against the requirement for reduced capital expenditure. The paper provides brief descriptions of the strategies employed in real-life situations and presents an overview of various operational parameters affecting the design of ventilation systems that will be used as ?platforms? for much deeper mines in the future.

Jan 1, 2007

By R Blair

The Domain and Burnley Tunnels, which are major features of the Melbourne City Link Project, are MelbourneÆs first road tunnels. They are 1.6 km and 3.5 km in length respectively and are being constructed through a variety of ground conditions. Deeper sections of the tunnels have been driven through the Silurian mudstone which underlies Melbourne. Other shallower sections of the tunnels pass through a variety of ground conditions including silts, sands, clay and rock and have been constructed using both top-down and bottom-up cut and cover construction techniques. The Yarra River Crossing is a 140 m length of the Domain Tunnel which crosses under the Yarra River on a relatively shallow alignment. The crossing of the river using cut and cover techniques was identified in the early stages of design development as being one of the most challenging stages of the works on the Southern Link. The prevalence of varying geological conditions combined with the need for maintained traffic and stream flow conditions provided a demanding and often conflicting set of criteria for which there appeared to be no one clear solution. A team of designers, constructors, estimators and specialist contractors were involved in a concept evaluation and risk analysis study spanning a period of approximately 12 months. During this study, four concepts were considered as likely contenders. This paper provides a brief outline of the four concepts addressing their relative merits, disadvantages and risks followed by a detailed description of the adopted solution, namely top-down construction using secant pile walling (east bank) and bottom-up in situ construction (west bank).

Jan 1, 1999

By D Cumming-Potvin, S W. Jacobsz and E Kearsley, J Wesseloo

This paper describes a physical modelling program that recreated block cave propagation in a geotechnical centrifuge. A brief description of the design of the test along with the sample material and monitoring equipment is given. The samples tested showed caving behaviour and fragmentation distributions that one would expect from caving mines, with one cave deviating due to pre-existing major discontinuities in the sample. A series of fractures formed ahead of and parallel to the cave, implying that an extensional failure mechanism may play a larger role in cave development than previously thought. The results of acoustic emission monitoring of the tests show a seismogenic zone advancing ahead of the cave; however, the quantity and quality of the data is too limited to draw any further conclusions.CITATION:Cumming-Potvin, D, Wesseloo, J, Jacobsz, S W and Kearsley, E, 2016. Results from physical models of block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 329–340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By using knowledge-based technology to create a Virtual Mining Enterprise and integrating it with existing technical and financial computer systems, a gold mining company has been able to reduce the time taken to produce a mine plan from 14 weeks to less than one week. Typically, the mine planning process requires circulating and managing large amounts of information. Even with the use of computers in todayÆs business, this is often still a manual process involving file transfers and individualised spreadsheets. Mine planning also involves understanding and managing large quantities of complex and interrelated variables. Added to this is the ever changing dynamics and constraints associated with the business of mining. These issues not only hamper the planning process but also question the validity and usefulness of the mine plans being generated. By integrating the information and knowledge of the numerous departments involved in mine planning into one core Knowledge Base - so called æone version of the truthÆ, - mining companies are able to overcome these pitfalls experienced in traditional planning methods. Once set up, the Knowledge Base creates and runs a virtual mining enterprise with which to visualise and test various scenarios of mining, business and logistical activities. The final output is an optimised enterprise-wide plan with clear and detailed instructions for each of the divisions of the company.

Jan 1, 2000

By Michael J. Lord, Richard H. O. Wagner

"The technologies used in the mineral processing of ores are being increasingly applied to the identification and remediation of metal contaminated industrial, military and landfill sites. The objective of mineral processing treatment of contaminated site material is to restore the value of the land and to concentrate the contaminants into a very small volume of separated material which, depending upon its nature, can be further processed, marketed, or sent to a landfill. A systematic characterisation of the site material is first undertaken. Bench and pilot testing follows to evaluate criteria for metal separation. The testing may examine one or more physical or physico-chemical reprocessing methods, singly or in combination, for the remediation of the test samples. These mineral processing tests determine the % metal removal fiom the soil and the contaminants concentrated from the medium. The usefulness of mineral processing testing for site remediation flowsheet design and execution is illustrated by the case studies presented. This paper will present the test results of three case studies: an industrial site decontamination, the cleanup of a small arms firing range, and the reclamation of property within a landfill.INTRODUCTIONEnvironmental legislation and our society’s quest for a cleaner environment has led to the application of mineral processing expertise and technology for industrial site decontamination, military site cleanup and landfill reclamation. Although the required level of decontamination varies between jurisdictions, a site becomes a candidate for decontamination once the contaminant concentrations are found to exceed the Canadian Council of Ministers of the Environment (CCME) Interim Remediation Criteria for soil (decommissioning guidelines) or applicable provincial guidelines. The objective of mineral processing treatment of contaminated site material is to restore the value of the land and to concentrate the contaminants into a very small volume of separated material which, depending upon its nature, can be further processed, marketed or disposed of in a landfill"

Jan 1, 1999

By F. P. Haver

The Federal Bureau of Mines developed a 10,000-ampere cell to determine the economic feasibility of producing high-purity electrolytic titanium from mill scrap or offgrade sponge. Operating variables were investigated, matetial handling procedures were established, and the cost of electrorefining titanium was determined. The prototype cell produced premium-grade metal (<100 Brinell hardness number (B.h.n.)) from very impure Kroll sponge at a processing cost of less than $0.60 per pound. Refined metal was deposited at the cathode in the form of coarse (85 percent plus 34-mesh), hexagonal crystals of a titanium when the cell was operated an 850° C. A cathode current density of 1,000 amperes per square foot and a molten sodium chloride electrolyte containing approximately 5 percent by weight of soluble titanium were used. In continuous operation, at the optimum number of ampere-hours, (40,000), the current efficiency averaged slightly less than 60 percent. It was possible to supply large enough amounts of electric current for electrolysis to maintain the temperature of the bath, thus reducing overall power consumption to less than 5 kilowatt-hours per pound of metal refined.

Jan 1, 1961

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents preliminary test results obtained with a 0.38 kg/s (3000 lb-hr) beta prototype MagMill™. In processing Upper Freeport coal the beta prototype recovered 82% of the weight of the feed and 91% of the heat content while reducing the potential emissions of sulfur, kgSO2/GJ(lbSO2/MBtu), by 61%. Pyritic sulfur in the MagMill™ product was reduced by 78% compared to that in the feed. For all runs, the mill product was controlled between 70 to 80% finer than 74 µ particle size. Recoveries of mercury, arsenic, and selenium ranged from 35 to 45% of that in the feed. Power draw was reduced by 26% and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2000

By Zhibao Li, Kunming Zhai, Yan Zhang

The hydration kinetics of MgO, namely magnesia or magnesium oxide, obtained by calcination of magnesite MgCO3 or synthetic MgCO3·3H2O has been studied. Nesquehonite (MgCO3·3H2O) was prepared by the reaction of MgCl2 with Na2CO3 in a mixed-suspension mixed-product removal (MSMPR) crystallizer at 40 °C. Three magnesium oxide samples were obtained by calcination of magnesite MgCO3 or synthetic MgCO3·3H2O in muffle furnace at 900, 1100 and 1300 °C for 3 h, respectively. The hydration experiments of MgO samples were investigated at 25, 35 and 45 °C for 24 h in a stirred batch reactor. The hydration results indicate that the rate and extent of hydration of magnesia decreased remarkably with hydration temperature and increased with decreasing calcination temperature at a constant hydration temperature. The whole hydration reaction of magnesia was supposed to experience the promotive period and declining period. An empirical kinetic model ( k t p -?ln(1-??) ??) and a modification of the classical shrinking core model for diffusion control ( k t b d -?-?3 2 ????1 [1 (1 ??) ] ) have been applied to fit the experimental data of hydration in two stages, respectively. The values of kinetic parameters ( p k and d k ) were obtained by regression analysis and the activation energy of the sample at 900 °C was estimated to be 34.23 kJ/mol. The comparison between MgO from calcination of synthetic MgCO3·3H2O and a commercial MgO used in silicon steel production was carried out, indicating that special silicon steel grade MgO can be obtained by calcination of MgCO3·3H2O below 900 °C.

Jan 1, 2014

By C. F. Lucks, W. D. Wood, H. W. Deem

Electrical ad thermal-conductivity measurements have been made on titanium and 6 titanium alloys. The following expression was derived for calculating thermal conductivity from electrical conductivity: K = 0.626 s T x 10-8 + 0.00497 where K = thermal conductivity, cal sec-1 cm-2 cm0C-1 s = electrical conductivity, ohm-]cm-1 T = temperature, deg Kelvin This expression gives calculated thermal conductivities that are not in error by more than 10 pct from the experimental values for A-55 titanium and the 6 alloys measured; namely, A-110AT, C-110M, C-130AM, Ti-6A1-4V, Ti-140A, and Ti-155A, which are representative of the presently available commercial a and a-ß titanium alloys. THERMAL conduction in a gas, liquid, or amorphous solid is accomplished by energy diffusion from molecule to molecule, a relatively slow process. For this reason, such materials have a low thermal conductivity. When a material is crystalline, there is in addition a heat transfer by a vibratory motion of the crystal lattice. It is the contribution of this lattice conduction that makes a crystal a much better conductor than a gas, liquid, or amorphous solid. Lattice conduction, however, does not account for the relatively enormous thermal conductivity of a metal. This is explained by the freedom of movement of valence electrons. These valence electrons drift in a metal in a direction toward a drop in electrical potential and, to a lesser degree, in the direction of a temperature drop in the metal. Since both the electrical and thermal conductivities of a metal depend upon the presence of free electrons, there should be some relatively simple relation between the two. Wiedemann and Franz in 1653 first discovered an approximate empirical relation between the electrical and thermal conductivities of metals at the same temperature. This ratio varies appreciably with temperature, and Lorenz later showed that by adding a temperature factor to the Wiedemann-Franz ratio the value of K/(s T) is constant, where K is the thermal conductivity, a the electrical conductivity, and T the absolute temperature. This Lorenz constant shows a greater variation for alloys than it does for pure metals, the ratio increasing slightly as the proportion of alloying elements increases. It has been found that a closer correlation between electrical conductivity and thermal conductivity can be obtained by means of an equation of the form K - A s T + B [1] where A and B are constants. In this equation the term AsT is the contribution of electronic conduction and B is the contribution of lattice conduction to the total thermal conductivity. EXPERIMENTAL MEASUREMENTS Electrical-resistivity and thermal-conductivity measurements on titanium and 6 titanium alloys serve as the basis for determining an equation of the K = AsT + B type for titanium alloys. Specimens—Table I shows nominal compositions of the 7 metals on which electrical and thermal conductivities were measured. The electrical and thermal-conductivity specimens for each alloy were taken from stock of the same heat and usually from adjacent sections of the same bar. All of the metals measured were in a mill-annealed condition. Methods—Electrical-resistivity measurements

Jan 1, 1959

Jan 1, 2000

By Peter Townsend, Sergei Diachenko, Allan Moss

The Palabora Mining Company has successfully extended the life of its operation by developing a 30,000tpd block cave underground mine below the now closed open pit. The process of transitioning from surface to underground mining has been technically, operationally and managerially challenging. This has been due to a number of factors; in particular, the development of a block cave in a very competent rock mass. The competence of the rock mass is clearly demonstrated in the open pit that preceded the block cave, one of the steepest deep open pit excavations in the world. With cave breakthrough, however, the pit was ?instantaneously? deepened by 400m causing a major failure of the northwest wall involving close to 100Mt of waste material.

Jan 1, 2006

By Peter Cunningham

General Description of Projects The objective is to streamline data transfer within our Process Control and Business Systems for the purposes of tracking actual production, reducing manual record keeping, improving process control and improving vehicle maintenance. This presentation focuses on two implementations of mobile equipment data acquisition systems which make use of industry standard data models and data transport protocols. Pilots are part of the Mines Technology Roadmap to improve our mining operations ?Enabling technologies and pilot of key systems

May 1, 2013

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and the introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-techno-logical cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

A numerical method for discriminating between replacement and sedimentary processes is applied to a folded stratiform sulphide occurrence. It is shown that numerical treatment of chemical analyses from a single diamond drill hole allowed a rapid assignment of the ore to the syngenetic sedimentary class and thereby enabled a revision of the evaluation program concerned with consequent reduction in costs.

Jan 1, 1973

By T. Aoki, Y. Maeno, R. Kawano, F. Nakahara, Y. Obara, K. Shibata

The mechanical behaviors of fully-grouted long-embedded cablebolts actually used in situ are very non-linear in pull tests and are different from those of short-embedded cablebolts. We have conducted the pull tests of long-embedded cablebolts installed in mockup rock test blocks, which are 4m in the longitudinal length. In order to investigate the mechanical behaviors inside the test block, the axial load distribution along the cablebolt and locations of acoustic emission events were measured during each pull test. It was found that the axial force distributions were quite linear and that the gradients were interpreted as the grout bond strength by taking into consideration the stress balance at the infinitesimal segment of a cablebolt. Les boulons-câbles longs entièrement cimentés qui sont réellement utilisés sur place présentent, au cours des essais de traction, des comportements mécaniques considérablement non linéaires et différents de ceux des boulons-câbles courts. Nous avons mené des essais de traction des boulons-câbles longs installés dans une maquette de fond rocheux servant d’éprouvette d’une longueur longitudinale de 4 m. Afin d’étudier les comportements mécaniques intérieurs de l’éprouvette, la répartition de la force axiale du boulon-câble et l’émission acoustique ont été mesurées durant chaque essai de traction. Il s’est avéré que les répartitions de la force axiale sont sensiblement linéaires et que leurs gradients représentent la résistance d’adhésion en prenant en compte l’équilibre de contraintes à la partie infinitésimale d’un boulon-câble. Das mechanische Verhalten von ganz eingegossenen, lang eingebetteten Kabelbolzen, die vor Ort eingesetzt werden, ist bei Zugprüfungen sehr nichtlinear und anders als das von kurz eingebetteten Kabelbolzen. Es wurden Zugprüfungen mit lang eingebetteten Kabelbolzen durchgeführt, die in Prüfblöcken (Gesteinsattrappen) mit 4 m Länge eingelassen waren. Zur Untersuchung des mechanischen Verhaltens in den Prüfblöcken wurden die Axiallastverteilung entlang des Kabelbolzens sowie das Auftreten von Schallemission im Verlauf jeder Zugprüfung gemessen. Es ergab sich, dass die axiale Kraftverteilung recht linear ist, und die Gradienten wurden unter Berücksichtigung des Kräftegleichgewichts am infinitesimal kleinen Punkt eines Kabelbolzens als Haftfestigkeit interpretiert.

Jan 1, 2003