Search Documents

By P. H. Reynolds, S. Liaghat, A. Zarasvandi

"Darreh-Zerreshk and Ali-Abad are two relatively small porphyry copper-type deposits in Yazd Province in central Iran. They are located within the central Iranian volcano-plutonic belt, formed above the collisional convergent margin of the Iranian lithospheric plate from the late Eocene to the Miocene. This paper discusses the geochemical characteristics of the igneous rocks, and 40Ar/39Ar geochronology of plutons and alteration phases associated with the Darreh-Zerreshk and Ali-Abad deposits. The deposits are spatially associated with igneous complexes that consist of older and barren granites intruded by intermediate-composition granitoids, which are the carriers of Cu mineralization. The granites have relatively high content of Nb, Y, and K, a prominent negative Eu anomaly, and were probably derived from melting of, or contamination of mantle-derived magmas by, continental crust. Porphyritic diorites, quartz monzodiorites, and granodiorites show enrichment in light rare earth and large-ion lithophile elements, depletion in middle rare earth elements, and have no negative Eu anomaly. These intermediate-composition granitoids were derived from melting of the upper mantle or lower crust, and their differentiation was controlled partly by fractionation of hornblende. A pilot K/Ar whole-rock dating study suggests that the pre-ore granites were emplaced in the Oligocene. Dating by the 40Ar/39Ar method of nine samples of secondary biotite and sericitized rocks from drillcore within the mineralized and altered zones in both deposits yielded a well-defined age of ca. 16 Ma. This date is interpreted to be the time of hydrothermal alteration and of porphyry copper type mineralization in this part of Iran."

Jan 1, 2007

By J. S. Hansen

To improve mine safety, the Bureau of Mines has conducted a search for better materials and systems to anchor roof bolts. This report describes a study on the ability of a gypsum-based anchoring medium to withstand short- and long-term loads. Results showed that 2-ft-long bolts anchored with gypsum that was injected as plaster slurry at a 0.370 water-cement ratio and cured for 10 min sustained pull test loads equal to the ultimate strength of the bolt steel (about 37,000 lb). For comparison, the minimum required capacity is 17,600 lb. Long-term loads of 15,500 lb were sustained with estimated 10-yr movement of less than 1/2 in. Two-foot-long bolts anchored with gypsum installed in a cartridge in which the water was contained in tiny capsules sustained a pull test load of about 30,300 lb at a 0.319 water-cement ratio and 10-min cure time. At a 0.288 water-cement ratio, load capacity was about 37,000 lb. The lower load capacities of cartridge-installed bolts resulted primarily from the remnants of the water-wax capsules. Above 10,000 lb, creep movement of cartridge-grouted bolts appears excessive, but longer bolts may be capable of resisting creep better.

Jan 1, 1985

By M. D. G. Salamon

It has been noted in recent years that the pillars in some bord-and-pillar workings scale or spall. In due course this process may result in the collapse of the affected panels. This paper presents a methodology for assessing the long-term behaviour of such workings, employing a simple model of pillar deterioration by scaling. It is assumed that scaling causes a gradual reduction in pillar width, hence the safety factor of pillars reduces in time. It is also postulated that the process of scaling will be arrested if the coal rubble around the pillar reaches a critical height. The probability that the pillars will survive for a certain period of time, or indefinitely, can be estimated. This can be accomplished by using the log-normal distribution proposed by Salamon and Munro4todescribe the distribution of the apparent safety factor values at failure. If an estimate of the rate of scaling is known, it is also possible to quantify, using a Monte Carlo technique, the expected life of the pillars. The method also facilitates pillar design by specifying a probability of survival for a given number of years or, alternatively, for an indefinite period. Using the limited pool of available data, analyses show that the proposed model does not appear to be inconsistent with observed behaviour of pillars in the Vaal Basin. The crucial parameter is the rate of scaling. Back calculations from eleven cases suggest that the rate of spalling in the Vaal Basin is about 0.2 m/year. It is noteworthy that two further cases in the same area give significantly higher rates (0.85 m/year). Some underground observations in the Witbank area indicate considerably lower rates in the order of 0.02?0.04 m/year. Further areas for study are recommended. These include a study of old workings to determine the extent and rate of scaling in the various coal fields, an investigation into the possible relationship between scaling and the chemical composition of the coal. In addition, model studies will be required to assess the practical impact of the research findings.

Jan 1, 1998

By S. Narasimha Rao

Bored cast in situ piles are highly susceptible to construction defects like necking, discontinuity in concreting, poor compaction of concrete, improper end bearing condition due to inadequate cleaning of bore hole, exposure of reinforcement, segregation of concrete etc. There is a necessity to understand the behavior of piles so as to design effective foundation system. In this paper investigations of two field cases were discussed to bring out the effect of defective piles. In one case improper end bearing has been discussed for a concrete pile of length of 45m and diameter equal to 1.2 m and is reinforced with 32 no's of 28mm diameter steel bars and in another case necking of the pile has been discussed. Further model piles with preformed defects have been tested in laboratory to bring out the influence of defective piles.

Jan 1, 1996

By Bruno Gemmi

A new warehouse built with prefabricated components over an area underlined by soft marine soil deposits started showing differential settlements well before its completion. Its 103 spread footings carrying up to 4,000kN (450t) axial loads had been cast on jet-grouted columns extending and penetrating a layer of sand at a depth of 10m (33ft). Investigations performed to assess the wholeness and consistency of the jet-grouted columns revealed a state of loose jet-grouted masses and uncontrolled, off target migrations of the jet-grouting. Most of the jet-grouting itself was settling. The following remedial solutions were suggested: 1. Construction of new and better controlled jet-grouted columns. 2. Cement-based soil grouting. 3. Expanding resin injections. 4. Minipiles drilled-through the existing footings and reaching into a denser layer of sand existing at 23m below grade. Remedial solution 1. was immediately discarded due to cost and the possibility of a repeating failure in this non-granular and highly compressible soil. Tests of remedial solutions 2. and 3. were carried out. The outcome of the grouting was monitored by Electro Resistivity Tomography (ERT) (Bares et al., 2003), an innovative 3D electro tomography procedure showing where grout had been actually placed and its migrations off target. A successful 4,000kN (450t) load tests confirmed the validity of the solution. Finally, upon the completion of a successful load test, solution 4. was chosen. It supplied the highest degree of reliability thanks to the ease of controlling the final and actual location of the minipiles and to the higher safety factor provided. All remedial work to install the minipiles was eventually performed inside the building. Additional load tests and settlement measurements confirmed the adequacy and success of the chosen solution.

Jan 1, 2011

By Joseph Grumer

Theory pertaining to the exchangeability of fuel gases on appliances has been extended to exchanges of propane or butane with mixtures of these. In particular, new considerations were developed bearing on the hazard of an occasional emission of carbon monoxide and flashback and blowoff possibilities. The new considerations involve using current requirements for approval of liquefied petroleum gas appliances. These requirements were used to predict allowable tolerances in chemical composition of liquefied petroleum gases for existing appliances. In addition, changes in gasline pressure were computed which may be substituted in place of fuel exchanges during testing of appliances,

Jan 1, 1962

Mine Terex articulated dump trucks are working on a large restoration project of an abandoned open cast coal site in Blacklaw, central Scotland. The project is part of the construction of a 42-turbine wind farm complex. During the scheduled 18-month duration of the project, three 28-t(31-st) Generation 7 TA30 dump trucks and the six 36.5-t (40-st) TA40articulated trucks are estimated to move about 1Mm3 (1.3 million cu yd)of material. The trucks are working12-hour shifts, 5.5days a week.

Jan 1, 2005

By Thierry Bernard

This case study shows how a unique combination of field measurements and advanced technologies allowed blasters designing, loading and firing an incredibly challenging quarry blast.

Jan 1, 2015

Small scale gold mining operations in Papua New Guinea (PNG) have been observed to use very low flow rates of water in sluice boxes. In a series of laboratory experiments carried out to determine whether this approach was unsatisfactory or not for their situation, indications were obtained that it had some advantages in the recovery of fine gold but at the cost of considerable throughput. The separation mechanisms operating in such a system are analysed.

Jan 1, 1986

By D. S. Kieffer

Ground characterized by hard boulders embedded in soft matrix represents one of the most challenging conditions for TBMs, as the cutterhead must cope with the non-optimal conditions of cutting hard blocks while simultaneously excavating through soft, soil-like matrix material. Dowden and Robinson (2001) and Hunt and Mazhar (2004) summarize several case histories relating to the problems of advancing a TBM through boulder-laden ground and provide guidance with respect to appropriate site investigations and baselining strategies. Some rock types constituting boulder-laden ground include: ?Sedimentary Rocks?cemented alluvial channel deposits, colluvium/talus, landslide debris, and glacial till. ?Igneous Rocks?agglomerates, lahars, and pyroclastic deposits. ?Metamorphic Rocks?tectonic mélange and cataclastic fault zones. ?Decomposed Rocks?corestone bearing saprolites. Disc cutters are commonly utilized to cut the hardblocks; however, as compared to the understanding of disc cutter behavior in hard continuous rocks, little is known regarding fundamental cutting mechanisms in highly heterogeneous bouldery ground conditions. To advance this understanding, a suite of full scale tests have been performed using a linear cutting machine at the Colorado School of Mines (CSM). This paper summarizes the observed cutting mechanisms and their practical implications for TBM excavations through boulder-laden ground.

Jan 1, 2008

By Mark Fennel

The present paper describes the operation and application of the QEMSCANTM automated applied mineralogy technology and how it is been utilized for long range planning by characterizing and optimizing the primary sulfide reserve while providing operational support of the ongoing secondary sulfide leaching operation at the Cerro Verde Mining Complex in Arequipa, Perú.

Sep 12, 2005

This report, authorized by a subcontract with the Crouse-Hinds Company per Section 1.1.3b of Contract Number H0220065 Amendment Number Six, and the consent of the Contracting Officer, documents the results of an investigation to develop solid state ballasts for Lucalox high pressure sodium lamps. The ballasts were to be used in the modified and new portable and machine-mounted lighting systems designed by the Crouse-Hinds Company, per Tasks I through IV of Contract No. H0220065.

Jan 1, 1976

By E. A. Lowe, A. F. Bellamy, J. W. Smith

"In the autumn of 1977 Bethlehem management initiated feasibility studies on recovery of by-product molybdenum from concentrate produced at the existing Highland Valley mining operation. Over the fall and winter months test work was carried forward concurrent with design, flowsheet, equipment specification and cost studies. The decision was made to go ahead with a 200 ton-per-day treatment plant. Construction started in early 1978 and progressed to an initial start-up stage in mid-June. Full operational status was reached in August 1978. Operational results through August 1979 are presented. INTRODUCTIONBethlehem Copper Corporation operates a 20,000 ton-per-day Open Pit Mine and Flotation Plant located in the Highland Valley, some 30 air miles Southwest of Kamloops and 20 miles Southeast of Ashcroft, B.C.Two open pits are worked; the Iona Pit with limited reserves of higher Mo content, and the lower grade, more extensive Jersey Pit. Upwards of 150 tons per day of bornite-chalcopyrite bulk concentrate is produced, ranging 0.25% to 1.5% in molybdenum grade depending on the area mined."

Jan 1, 1980

By Penrose E. K

With the exception of occasional periods, when up to 80% of oxidized ore was treated, the G.M.K. plant treated all sulphide ore until October, 1939. The treatment was, briefly, as follows:The ore was ground to approximately 17% plus 200 mesh Tyler and agitated in cyanide solution, after straking. After agitation, the pulp passed through two stages of counter-current decantation washing in Dorr thickeners and was filtered once, to complete the precyanidation stage.The precyanide filter cake was repulped with flotation circuit solution and floated in a Denver Sub A flotation machine, consisting of twelve cells. The concentrates were roasted, cyanided and filtered four times before disposal to the' dam. The flotation tailings were thickened to conserve water and pumped away to a separate dam.The average results of flotation operations for the six months before October, 1939, are shown in Table 1.

Jan 1, 1942

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the U.S. Department of the Interior, Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows were continuous except for short periods when resin increments were withdrawn. The exchange of uranyl carbonate between a simulated in situ uranium leach liquor and a strong-base ion-exchange resin together with the subsequent elution with an ammonium chloride solution was studied. The effects of the number of sections, section height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. The kinetic and equilibrium relationships for the absorption and elution steps were also examined. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By Fernando Bermejo

El presente texto describe la implementación del método Flash - Flotation para el proceso de optimización de plantas concentradoras polimetálicas en la Compañía minera Raura donde se tienen diferentes gravedades especificas por cada especie mineralógica. Su aplicación comprende la fase de investigación (año 89), modificaciones (año 2002) durante la etapa de escalamiento industrial y la optimización (año 2004) de estos equipos en la empresa, los cuales no han requerido de una gran inversión. Asimismo, los beneficios de operar con la celda SK-80 y SK-240 directamente a la descarga de los molinos primarios, permite optimizar el control metalúrgico. En este sentido, la idea de separar el plomo tan pronto lo permita el sistema, es la forma correcta de optimizar la metalurgia de este en la Compañía minera Raura.

Sep 12, 2005

By Kenneth E. Hay

Researchers from the U.S. Bureau of Mines conducted a field study to assess the safety of remotely controlled mobile roof supports (MRS) in a retreat pillar mining operation, Data were collected to provide the Mine Health and Safety Administration with criteria needed to develop guidelines for MRS use and to determine if precursors could be identified that would alert miners to imminent roof falls. Two test sites at which two different support methods-MRS's and posts were used and were monitored to obtain information on entry stability. Pressure transducers and string pots were installed on all four MRS's to obtain loading and displacement information. and roof bolt load cells. sonic probes, extensometers, and survey targets were installed in the surrounding entries to obtain information on ground behavior. Results showed a larger increase in roof bolt loading and roof movement when MRS's were used, especially in the intersection area. Roof bolt loads in the entries showed decreases in load when the MRS's were set and increases up to 11,1 kN (2,500 lbf) when the MRS's were unloaded. Unloading of one MRS in a pair did not significantly increase load on the other. MRS's I and 2 usually had the higher loads, with these loads increasing as the pillars on each side were being mined. MRS 3 normally had lower loads than I and 2: however, it also experienced some very high loads when in the last position near the pushout. MRS 4 usually had the lowest loads, primarily because it was located near the solid pillar that was not being mined.

Jan 1, 1995

By G. L. Smith

Central to the success of any mining company is the ability to manage capital investment effectively so as to ensure acceptable stakeholder returns within an overall strategic context. Critical to this process is the effective selection and implementation of a strategically aligned project portfolio that enables optimal resource exploitation while operating within mandated bounds and identified constraints. Consideration is given to the strategic long-term planning process, an investment prioritization methodology and specific tools and techniques based on the discounted cash flow philosophy.

Jan 1, 2007

By Frank Sames

Most Blasting Programs are developed focussing on the environmental impact with respect to blast vibration and airblast. Compliance with existing regulations or policies limiting the immissions are generally achieved through constrains in the blast design, or monitoring programs. Efficient monitoring programs combine compliance monitoring and blast assessment. Signals, which are obtained in the area of direct influence of the seismic source, can contain valuable information about the blast design parameters. Techniques to analyze blast vibration signals have advanced and can assist in understanding the contribution of individual blast parameters to blast vibration and airblast. Advanced signal analysis encompasses magnitude analysis, Fast Fourier Transforms (FFT) and frequency scans in the frequency domain, as well as filtering in the time domain. Through examples, the advanced signal analysis techniques and their limitations are described and discussed, showing the impact of blast timing, timing accuracy, charge configuration and the geology dependent transmission behavior. Optimization criteria and pragmatic monitoring programs can be developed on the basis of the most influential blast parameters. In addition, however, safety and the cost efficiency of the blasting program are essential to the success of an operation. That is where advanced signal analysis techniques can interface with blast planning, computer assisted modeling and information systems. A valuable process can be developed to ensure compliance with existing regulations and efficient risk management for mining operations, while tracking cost and supporting operational decisions. A conceptual blasting information system is presented.

Jan 1, 2000

By Javier A. Llano

GPS, wireless communications and on-board and off-board computing capabilities provide today’s mining companies with unprecedented process improvement and cost reduction opportunities. All aspects of the operation from engineering, surveying, drilling, loading, hauling and support can benefit from products like CAES and Drill Monitor. These technologies, which have been working at world class mines around the world in some cases for over three years, are helping customers achieve new lows in cost per ton. Manually intensive and time-consuming processes like in field surveying are replaced by timely mine status information wirelessly transmitted from the machines to the office.

Jul 17, 2000