Search Documents

By Lawrence Pelham

Introduction Fluorspar demand or consumption has been taken for granted in recent years, except for those that produce, market, or consume the commodity. Thinking used to be that as the steel and aluminum industry goes, so goes fluorspar. This is much less true today. The industry is becoming more dependent on chemical industries that feed primarily off hydrofluoric acid (HF) production. The US Bureau of Mines (USBM) published an assessment of world fluorspar reserves and resources. It created a foundation of valuable data that can be used to monitor fluorspar availability. Celebrations were held this year commemorating the 100th anniversary of the isolation of fluorine. The US and other countries continue to struggle with the controversy of ozone depletion and the effect of fluorocarbons on the atmosphere. Goals for the government's strategic stockpile are being reevaluated. The market for fluorine chemicals is changing and diversifying, making it a challenge to assess and forecast fluorspar/fluorine demand. US production and distribution Fluorspar Fluorspar shipments from US mines reached an all-time high near the end of World War II in 1944 at 375 kt (413,800 st). Eighty-two mines produced more than 453 t (500 st) each, and 10 mines produced more than 9 kt (10,000 st.) each. Illinois supplied 43% of total shipments. Consumption in 1944 was 372 kt (410,200 st), of which 56% was used by steel producers and 32% by HF producers. This was the last year that US production exceeded US consumption. The post-World War II record for fluorspar shipments occurred in 1951 at 315 kt (347,000 st) 58 mines produced more than 453 t (500 st) and eight mines produced more than 9 kt (10,000 st).

Jan 11, 1986

By K. A. Lapakko, D. A. Antonson

Fourteen samples of pyrite-bearing Archean greenstone rock (d < 6.35 mm, 0.04% < St < 1.22%) were characterized (particle size, chemistry, mineralogy) and subjected to laboratory dissolution testing. The only sulfide and carbonate minerals identified were pyrite and siderite, respectively. Quartz, chlorite and sericite typically comprised 90 to 98 percent of the mineral content. For the first 60 weeks, seven samples with sulfur contents less than or equal to 0.16% produced drainage pH values exceeding 6.0. Over this period, six of the seven samples with sulfur contents greater than or equal to 0.20% produced drainage pH below 6.0, with minimum values ranging from 3.2 to 4.7. The seventh sample (0.72% S) had a siderite content of 18%. Small amounts of magnesium and, to a lesser degree, calcium carbonates present in the siderite apparently dissolved to neutralize acid and maintain drainage pH above 6.0. Sulfate release rates generally increased as sulfur content increased, and the rates of pyrite oxidation estimated for individual samples were roughly half to five times that reported in the literature for the abiotic oxidation of pyrite by oxygen. Observed neutralization potentials ranged from 0.2 to 2.0 g CaCO3/g rock.

Jan 1, 2002

By David Ziegler

Rough sketches, field notes, an on-site conference or a phone call may no longer suffice to establish your blast plan at a job site. More and more, general contractors, site supervisors, owner re p resentatives, or the owners themselves want to know details about proposed drill and blast operations at their site, in advance. We are seeing more contracts that re q u i re a blasting plan to be submitted in writing. The purpose of this session is to discuss items that you might want to include and address in a written blast plan, and some ideas about how to present them. This is not intended to be a complete list of items that could be included in a blast plan. Contracts may list specific items that need to be addressed. Only a few of the more common elements will be covered here. The bro a der purpose of this discussion is to get you thinking, about what you might want to include in your own “standard ” blast plan.

Jan 1, 2004

By Gavin J. Faulkner

This paper presents an investigation of some alternatives, and improvements to timber posts and cribs. The purpose is to find a cheaper, better, easy to install, and effective means to replace or improve them. Selection of supports needs to take account of several factors. These factors include the mechanical behavior of the support, technical feasibility, and cost. In this paper a variety of supports are compared on these bases. Particular advantages and disadvantages of those supports have been determined through published material and a testing program. A broad evaluation of a number of specific groups of supports is presented. Included in this evaluation are timber posts and cribs, steel friction props and several, newer developments such as the Micon Yield Capsule and the Super Post. Another support that will be briefly discussed is steel-fiber-reinforced concrete. Particular emphasis will be placed on the Micon Yield Capsule and the Super Posts on which preliminary testing has been carried out. The testing results are presented in detail. The shortcomings of the test procedure are pointed out and some new ideas to improve the testing in the future are proposed.

Jan 1, 1986

It is possible to divide industrial minerals into four general categories: 1. fuels, 2. construction&nbsp;materials, 4. agricultural minerals, and 4. industrial minerals. It is proposed to ignore the fuels in the context of this paper and deal in general terms with the others. Mining companies have often considered getting into the industrial mineral business because they can see a resource development with good growth and consistent profits. However, many mining companies being conversant with the metallic side of the industry have spent sleepless nights determining which industrial minerals are most suited for their particular situation. Some have got into the business for the wrong reasons and wished they had never heard of it. Others have successfully adapted to the industrial minerals philosophy and now operate in both metallic and industrial mineral arenas. There is a large difference between firstly, the philosophy and secondly, the functions of being in the industrial minerals business as opposed to metallicÆs. The philosophies can be considered in parallel but it is necessary to clearly have an appreciation of the dominant influences that affect industrial minerals.

Jan 1, 1984

By B. Tiryaki, O. Z. Hekimoglu

Shearer drums are a critical component in the overall performance of coal shearers, with the cutting performance depending very much on the disposition of cutter tools on the drums (the tool-lacing arrangement). A series of practical and theoretical studies has been undertaken to investigate aspects of shearer drum vibration in terms of circumferential pick spacing. A number of commercially available drums were redesigned and the lacing patterns compared with those of the original drums under near-uniform conditions. Mine trials were carried out at the Middle Anatolian lignite mine in Turkey with drums fitted on Eickhoff type EDW-230 double-ranging drum shearers. It was found that the performance of drums could be improved if the concept of circumferential pick spacing was taken into account in CAD packages along with the existing design parameters such as cutting rate, reduced dust, low pick consumption and low down-time

Jun 19, 1905

By David A. Benjamin

At the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied prospects, claims, and mineralized sites in a 43,053-acre portion of the 51,262-acre Desatoya Mountains Wilderness Study Area (NV-030-l10) in 1985. The study area, located 50 miles east of Fallon, NV, is underlain by alluvial deposits of Quaternary age and volcanic and volcanic-derived sedimentary rock of Tertiary age. No mines or recent exploration activity were identified within the area studied. The Gold Basin area, located 1/2 mile to the south has produced 982 ounces of gold and 10,086 ounces of silver. The Cold Springs area, located 1/2 mile to the west, has recently been explored for gold-silver. Mineralization at these two areas apparently did not extend into the study area, but future mining at these areas would likely impact it.

Jan 1, 1986

In spite of the many contributions that have been made to our knowledge of the creep properties of polycrystalline lead, the precise influence of various factors on these properties is not yet fully understood. Indeed, the position is such that several important points in connection with the creep of lead are a matter of controversy. This has been brought about largely by the fact that, in the case of lead, the changes that are produced in the creep behaviour by slight variations of such factors as the purity, grain sizeand previous treatment are out of all proportion to the magnitude of these variations.In order to study the fundamental properties of lead as related to creep, and so gain a more enlightened perspective with which to consider the creep of lead in general, the work that is described in a series of papers, of which the present paper is the third part, has been carried out. It deals with lead in the form of single crystals.It has been shown (1) - (3) that the grain boundaries as well as the actual grains play a part in the creep of polycrystalline lead. The present work, by eliminating grain boundaries, enables the. contribution of the grains themselves to the process of creep, in other words, crystalline creep, to be studied effectively.This object was, possibly, the major one in this work.

Jan 1, 1940

This Bureau of Mines report describes research on methods of assuring the continued safety of mine electrical power distribution circuits through reliability and quality assessment of the protective devices, innovative inspection techniques for these devices and the circuits themselves, novel applications of trolley line circuit breakers, and computer modeling of distribution systems to determine the proper ratings for cables, power sources, and circuit protective elements. Battery charger safety is included.

Jan 1, 1979

By R. L. Virta

Ball Clay -- Four companies - H.C. Spinks Clay Co. Inc. (owned by Lhoist Group), Imerys Group (formerly Kentucky-Tennessee Clay Co.), Old Hickory Clay Co. and Unimin Corp. - mined ball clay in four states during 2010. Production, based on preliminary data, was 910 kt (1.11 million st) with an estimated value of $42.9 million. That was a 10-percent increase in tonnage from 831 kt (916 million st) with a value of $37.7 million that was produced in 2009. Tennessee was the leading producer state with 61 percent of domestic production. It was followed by Texas, Mississippi and Kentucky. About 70 percent of production was airfloat, 20 percent was crude and 10 percent was water-slurried.

Jan 1, 2011

By Frederic Benard

PRIOR to 1936, the Ontario Refining Co. received all incoming blister copper from The International Nickel Company&apos;s smelter in the usual form of 460-lb. cakes, or slabs. These were received in open cars in lots of 250 pieces. At the refinery the cakes were unloaded onto narrow-gauge cars, for convenient handling and pickup by charging cranes. In March 1936, an investigation was started on the feasibility of transferring converter copper in the molten state from the smelter to the refinery anode furnaces, a distance of 1 ¼ miles. Although common in steel practice, the transportation of blister copper in this form had not previously been attempted and a preliminary study of the various factors involved was therefore necessary. For this purpose, a series of experiments was made in which molten copper, removed at different stages during the furnace cycle, was held in a small portable holding furnace. This vessel was essentially a refractory-lined steel cylinder provided with ports for filling and emptying, heated by an oil burner. Dimensions of the steel shell were 3 ft. 10 in. diameter by 7 ft. 3 in. long, and thickness of refractories depended on the design and combination used for the particular experiment. The vessel was filled with approximately 2 ½ tons of copper at a predetermined temperature, the lining having been preheated to a definite point by means of an oil burner. All openings were well luted and temperature readings were made every 15 min. by means of an immersion-type thermocouple. In this manner the rate of heat loss resulting with different refractory design could be developed. The ratio of exterior surface to weight of metal was taken into consideration in comparing the experimental results with what might be expected for a full-sized unit, and observations were also made on type and degree of slag accretion. It was not possible to get as much information on this latter point as desirable, but all evidence showed that the problem would be control of slag build-up rather than attack on refractories. From the information derived, and in consultation with the engineering staff of the supplying company, an order was placed for the first

Jan 1, 1938

By D O’Dea, B Godel, T Honeyands, G Evans, T Harvey

The pores within iron ore sinter are important for producing a high quality material that is strong and easily reduced. The complementary methods of mercury intrusion porosimetry (MIP) and X-ray computed tomography (CT) were used to characterise the structure of industrial and pilot scales sinters across a wide range of pore sizes (3 nm to 100 µm for MIP and 50 µm to 5 mm for CT). The inhomogeneous nature of sinter and the variation in the measurements make it difficult to compare samples. The generalised additive modelling (GAM) approach, using the open source statistical software package, R, has been applied to highlight where there are peaks in the concentration of pore sizes. Importantly, the shape of the GAM-fitted function and the heights of the peaks show statistically significant differences between samples. For the samples investigated, the GAM-fitted functions for the MIP volume distribution of pore diameters were found to have a common set of distinctive peaks at 0.005, 0.6 and 20 µm. The GAM approach was also applied to the X-ray CT measured pore wall thickness, highlighting a single peak whose position varies between samples. The cause of these distinctive peaks and their implications for sinter quality are discussed. Correlation was found between the volume in peak 1 (0.005 µm) and the concentration of primary hematite. No correlation was found between the pore wall thickness and the strength of the sinter, suggesting the composition of the pore walls may be more important. Future work will focus on small-scale sinters produced under tightly controlled conditions to study sinters with a wider range of quality values.CITATION:Harvey, T, O’Dea, D, Evans, G, Godel, B and Honeyands, T, 2017. Highlighting key features of the pore structure of iron ore sinter using mercury intrusion porosimetry and X-ray computed tomography, in Proceedings Iron Ore 2017, pp 39–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Sam S. Taylor

In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas produced With the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production nest be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a gas supply is not available, often air is used. Although air is a cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, some fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case.

Jan 1, 1934

By R. Curtis

To achieve compliance with 2015 EPA Tier 4 Final regulations, which permit only around 10% of Tier 3 particulate matter (PM) and NOx emissions, a number of technologies are being implemented. Use of a fuel borne nanoparticle combustion catalyst reduces the level of PM and unburned hydrocarbons exiting the combustion chamber, alleviating the burden on downstream exhaust after-treatment systems. The impact of an iron-ceria combustion catalyst (GO2) on carbon oxidation kinetics and on diesel engine emissions is presented. The iron-ceria nanoparticles catalyze carbon oxidation at lower temperatures and increase the oxidation rate by a factor of 18 at 400 °C. Engine tests on a generator powered by a John Deere Model engine and field tests on a Cummins ISC 330 tractor truck and CAT 3508B propulsion engines are presented. Use of GO2 resulted in a reduction in PM10 (particulate matter under 10 um) emissions of up to 26% and a hydrocarbon emission reduction of up to 41%. NOx emissions did not increase in these trials and the amount of change depended on engine type. Application of this fuel borne technology for emissions reductions in mining equipment offers significant benefits.

Feb 27, 2013

By Misra V. N

Upgrading of a Koolanooka magnetite iron ore sample provided by Kingstream Steel Ltd was investigated using low intensity magnetic separation (LIMS) and reverse flotation. The ore contained 38.6 per cent iron, 37.8 per cent silica, 6.5 per cent magnesia and 0.54 per cent alumina, with the main minerals in the ore being amphibole (42 per cent), magnetite (39 per cent) and quartz (14 per cent). The concentrate obtained after low intensity magnetic separation contained 66.6 per cent iron and 6.34 per cent silica with an iron recovery of 72 per cent. This concentrate was further treated by reverse flotation to increase the iron content and reduce the silica content to meet the requirements for direct reduction iron (DRI) feed grade.

Jan 1, 1999

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By C. van Tonder

Paper written on project work carried out in partial fulfilment of B Tech (Engineering Metallurgy) degree This investigation relates to a multi-purpose electrolytic system. Its primary purpose is to electrowin gold from high or low concentration gold cyanide solutions and/or from gold sludge, and to convert the recovered gold into a gold (alloy) electroform or electrode at the gold mine itself. These operations are carried out sequentially and in situ in the same electrolytic cell. Electrorefining of the gold recovered may also be done in the cell. The system applies to silver as well, and may be adaptable to base and platinum group metals. It could also be used in environmental applications, to remove undesirable metals present in aqueous solution at very low concentration. The work to be discussed forms part of recently filed patent applications. Subsequent and future developments of the system are briefly outlined. This paper, in part or in full, has been published by the Metallurgical Mine Managers Association (MMMA), with permission from the authors.

Jan 1, 2006

A device is described which is suitable for the automatic sampling of dust in dust laden flue gases. This device, called a Venturi Sampler, consists of two pipes each fitted with a suitably designed venturi.Both pipes are placed in the flue where one acts as an open-ended reference tube and the other as the actual sampling tube.The gas sampling rate is automatically controlled so as to maintain a zero differential pressure between pressure tappings in the two venturi throats. The venturies are so designed that under these conditions the gas velocity in the sampling pipe is always equal to the free gas velocity in the flue-that is isokinetfc sampling conditions are maintained.INTRODUCTIONThere is a constant need in industry for regular and accurate assessments of dust losses, both to assist in improving operating efficiencies in order to minimize losses, and to obtain accurate metallurgical balances. In many cases where sampling is carried out in dust laden gases, the existing sampling methods are both laborious and inaccurate, and often make no provision for changes in flue gas velocity while sampling is in progress.In the majority of cases where a measurement of dust losses in a stack or flue is required, a preliminary velocity survey is made with a pitot tube to establish the gas velocity at each of the points at which samples are to be taken. The sample of gas (and dust) is withdrawn through a tube connected via a flowmeter to an exhausting apparatus. Some means of removing the dust from the gas sample is placed in circuit ahead of the exhausting apparatus. This is often an alundum or paper thimble housed in a gas-tight container.The purpose of the flowmeter is to measure the actual flow of gas during sampling so that the sampling velocity at the inlet to the sampling tube may be calculated, and the flow corrected so that the sampling velocity will agree with...

Jan 1, 1959

By Jamie King

This paper describes the use of dynamic scheduling and discrete event control to provide coordinated control of multiple automated vehicles. In the past decade there have been significant advances in the field of robotics for underground mining. As this trend progresses toward a realization of a completely automated underground mine the need for a central control system, capable of providing coordination for multiple vehicles in a semistructured environment, becomes more evident. In the past year general research into multi-robot coordination has been applied to the underground mining scenario and demonstrated in a scaled model underground mine in a laboratory setting. This system shows significant potential to be adopted into a full-scale implementation for mine wide automation.

May 1, 2001

Jan 1, 1989