Search Documents

By Peter J. Nicholson

Since the reintroduction of soil mixing to the United States over 10 years ago, the work installed by soil mixing technology has grown dramatically. From an annual turnover of less than ten million dollars per year the volume of soil mixing put in place has grown to an estimated $40 million per year in the year 2000. The majority of work done to date has involved walls, either for excavation support, permanent retaining structures or hydraulic cut-off walls. The other major use for soil mixing has been for mass stabilization of soils whether for isolation of contaminants or for retaining structures. This paper will discuss the uses of and costs of typical soil mix structures. BACKGROUND Soil mixing is defined as the in-situ combining of reagents, typically cement, with native soils, the purpose being to modify or improve the ground. This history of soil mixing covers only the use of cement slurry, aggregated with soil in-situ by mechanical mixing methods only. Soil mixing by use of high-pressure hydraulic means, also known as Jet Grouting, will not be discussed. In addition this will not cover ex-situ (above ground) mixing, or mixing dry reagents with soil. Only mixing applications for building, civil and heavy construction applications will be discussed, with only passing reference made to uses of soil mixing for environmental remediation work.

Jan 1, 2001

By Pedro Lilienfeld

This report describes the development, design, fabrication and testing of a port-able, battery-operated, light scattering monitor (henceforth to be designated as ILSDM) for the rapid measurement of the concentration of respirable dust in mining environments. This instrument incorporates state-of-the-art design characteristics and makes use of advanced solid-state components both for light emission as well as for its detection. The use of a pulsed light source combined with synchronous signal detection minimizes drift problems and optimizes the sensitivity of the measurement. Simplicity of operation, reliability and ruggedness, light weight as well as improved performance were salient objectives of this instrument development program. Continuous clean-air flow screening of all critical optical surfaces, and optimized optical detection and electronic signal processing design resulted in about a hundred-fold decrease of noise and drift with respect to precursor instruments. Equivalent mass concentration measurements 88 low as 10 micrograms per cubic meter can be routinely performed with time constants of about 2 second.

Jan 1, 1979

By J. N. Van der Merwe

The data base of failed pillar cases as used by Salamon and Munro (1967) in their original analysis to determine the strength of coal pillars empirically, has been updated for this study. It is shown that the Vaal Basin and Klip River coal fields exhibit similar behaviour that differs from the failures in other areas, i.e. failure at high safety factors within a short period of time. Those collapse cases have been omitted from the new data base. Failures in the other areas that occurred after 1967 have been added. Using a technique to minimize the area of overlap between the populations of safety factors of failed and intact pillar cases, the new data base was re-analysed in conjunction with the original Salamon-Munro data base of intact pillar cases, from which the cases in the areas of weak coal were likewise eliminated. It was found that a linear formula reduced the overlap area by22%. The new formula predicts higher strength for pillars with a width-to-height ratio greater than approximately 2.0 to 3.0 and a lower strength for smaller pillars. It was also found that in order to obtain the same relative measure of stability as with the Salamon-Munro formula, the strength constant in the new formula should be within a range of 2.8 to 3.5 MPa. For most current South African coal mining conditions, using the new formula for pillar strength will result in leaving smaller pillars without sacrificing stability. The reason for this is that the Salamon-Munro formula under-estimated the strength of larger pillars and over-estimated the strength of smaller pillars. The new formula will thus result in improved reserve utilization without sacrificing stability.

Jan 1, 2003

A series of gas inrush events occurred during development at Grosvenor mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred releasing between 15 and 130 m3 of methane during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective pre-drainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs (C/Ts) perpendicular to the principal stress direction, no events occurred, and higher methane levels were observed at the production face.

Jan 7, 2020

Total mechanisation in the Western district of New South Wales is quite a recent addition to productive methods in that State, for it was only in 1940 that the first colliery was equipped for this method of winning coal. Now almost all mines either are totally mechanised or are planning to get their coal by these means.This marked change in recent years is explained by the salient features of the industry's history. Collieries in New South Wales had generally been subjected to low selling prices forced on them by over-production and severe competition. Little money was available out of profits to purchase machinery, and returns on capital were so poor that inducement to invest money in the industry was nonexistent.The second world war brought price fixing at the already low prices. It was not until the post-war period that there has been any inducement to mechanise.Much credit for mechanisation can be given to the Joint Coal Board, a government body formed in 1948. Pursuing a broad plan for the rejuvenation of the industry, this Board, purchased large quantities of machinery for use in, mines under hire-purchase agreement. These agreements encouraged machine mining, and this fact, together with the ensuing production economies, has improved the financial position of the industry.The Board has also been instrumental in the granting of increases in the fixed price of coal, so that the industry has been given an even greater boost in the direction of mechanisation.

Jan 1, 1954

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996

By W. L. Thayer, K. A. Jonasson, R. D. Coleman, J. D. Hazlett, C. E. Capes

"Loss of coal fines in reject slurries limits the yield of coal cleaning operations. Difficulties in handling fines also limit the extent of physical cleaning in treating coals with finely-disseminated impurities. Selective oil agglomeration allows even extreme fines to be processed and offers some novel approaches for coal cleaning and utilization.The oil agglomeration process for the recovery and beneficiation of fine and ultrafine coal has now been commercialized by the Chemical Engineering Section/Chemistry Division of the National Research Council (NRC). This paper describes these activities to apply oil agglomeration and related fine coal technologies on an industrial scale. Pilot plant and large scale results are described, as well as aspects of agglomerate utilization in both wet and dry form."

Jan 1, 1988

By John E. Lens

Minutes after the Friday afternoon October 16, 2009 announcement that the 80 year old Lake Champlain Bridge was closed to traffic out of concern for public safety, emergency detour planning started at VTrans and NYSDoT. The closure severed a cross-lake link between Addison, VT and Crown Point, NY, which created a 76 mile detour and significant hardship for commuters, farmers working on both sides of Lake Champlain, and businesses relying on both traffic and employees commuting between Vermont and New York. Rehabilitating the bridge was determined to be economically and technically unfeasible and the design of a replacement bridge was accelerated for a spring 2010 construction start. In the meantime, a temporary ferry alternative was to be rushed into service beside the original bridge by February 2, 2010. This paper presents the case history of the fast-tracked ferry dock design and construction on the Vermont side. Twin 300-foot-long pile supported approach spans, a loading slip system and ice deflectors were designed, fabricated and constructed in 90 days in the fall/winter of 2009-2010. This chronicles the project from initial concepts through the extraordinary cooperation between state and federal agencies, and near round-the-clock winter construction on Lake Champlain. This project and its companion project on the New York shore succeeded by virtue of exceptional cooperation between seasoned regulatory, design, and construction participants and warrant this case-history presentation of the Vermont project to share within the industry as an example of overcoming extraordinary challenges.

Jan 1, 2011

By Ravi Ray, Kostas Kaklis, Zach Agioutantis

"Modern underground mining is becoming more complex and geotechnically challenging. The engineer uses numerical, analytical, and data-driven methods (empirical and/or experimental) or their combination to overcome these challenges. Each method has its advantages and disadvantages. Nevertheless, given the amount of innovation and experience involved in developing each of these techniques, it will be prudent to use all their benefits rather than favoring one technique over the other. Pillars are the most important support element in an underground mine. A holistic geo-mechanical solution needs to be determined to design mine pillars using a proper sequence and exact mix of the three methods. A combination of these methods, in sync, can encompass the several advantages of the three methods while eliminating their disadvantages. This paper presents a conceptual three-tier solution to the pillar design problem, to improve its design pedigree, using a proper combination of numerical, analytical, and data-driven methods. At the focus of this proposed method lies the Ground Reaction Curve (GRC) concept.INTRODUCTIONAlthough the stability analysis of underground excavations is a challenging problem, its understanding has improved tremendously over recent years through the use of improved tools and techniques. The trial and error method was replaced with more scientific methods like the empirical and analytical methods that are still in use today. Empirical methods were developed based on large data sets obtained from experiments and observations (e.g., coal pillar strength equations). Analytical methods were developed based on mechanical understanding of stability (e.g., safety factor for vertical pillar loading, Convergence Confinement Method). Improvement in computing power and numerical techniques led to the development of several numerical methods (e.g., finite difference, finite element) suitable for geo-mechanical analysis.Each of these methods have certain advantages and limitations. Nevertheless, the user is often puzzled over the proper method selection and over the proper sequence of using them. This exercise becomes more challenging when different methods are combined, where, for example, one has to estimate the pillar strength based on empirical equations (e.g., Mark-Bieniawski coal pillar strength equation), determine the factor of safety based on an analytical approach (e.g., tributary area load divided by pillar strength), and analyze pillar-strata interactions using numerical analysis (see Esterhuizen, Mark, and Murphy, 2010b).Challenges increase when current pillar design methods are designed as passive structures to balance the fixed dead weight of the overburden. This classic suspension design approach does not recognize the self-stabilizing capacity of the overburden (Frith and Reed, 2018). A practical solution to address these issues is the use of numerical analysis. However, one should always keep in mind that the numerical modelling approach may have certain practical limitations."

Jan 1, 2019

Jan 1, 1972

By A. L. Grabovski

The potential of eccentric cone crushers for fine crushing has been improved by increasing the swing frequency of the moving cone, balancing the crusher, ensuring uniform feed via a rotating funnel with sideways discharge, introducing hyperbolic motion and employing the inertia crushing method, but further improvements to the specifications of existing cone crusher designs are limited by the rigidity of their kinematic coupling. A new design has been developed which combines two crushing modes, stone on liner and stone on stone, each with its own advantages. The main aims are to produce finer materials and to reduce liner weight. The benefits include an increase of more than 10% in the output of fine particles, improved protection of the liner against wear, as a result of filling of the cavities by material being crushed, and the use of almost 20% less material in casting of the liner. The chamber can be used in place of the usual liners of fine cone crushers

Jun 21, 1905

The cost of preparing a feasibility study is notoriously difficult to estimate. Studies for mining projects are typically commenced when an exploration programme has identified a mineable resource and pre-feasibility studies have shown that development of the resource would lead to an economically viable project. Pre-feasibility studies will normally include an estimate of the cost of a formal feasibility study and this estimate would then be firmed up before a commitment is made to proceed with the formal study. Data for preparing the feasibility study cost estimate will be sketchy, geological investigations, metallurgical testwork, and marketing studies may be needed before the scope of the project and hence the scope of the formal study can be finally determined. Before an estimate of the work required and hence of the cost of the feasibility study can be prepared the source of project funds must be decided. Studies for internally funded projects are often less rigorous than those which must be "bankable" and subject to the scrutiny of external financial institutions. This paper sets out suggestions for preparing more accurate cost estimates for feasibility studies by ensuring that all activities are included and shows how a staged approach to preparing such studies can minimise costs and guard against cost overruns. It also provides a case study showing how the estimate compared with actual costs for a recent feasibility study completed by Pancontinental Mining Limited.

Jan 1, 1990

By J. R. Ross

Recovery of uranium from slightly alkaline mine water, available in the Ambrosia Lake district of New Mexico, was studied using countercurrent ion exchange columns developed by the Bureau of Mines. Approximately 5 million gallons of mine water containing 9 to 12 ppm U308 was treated by ion exchange using a 14-inch-diameter absorption column composed of five or six compartments each 4 feet deep. Uranium recoveries averaged in excess of 98 percent at solution flows ranging from 15 to 25 gallons per square foot per minute and resin loadings up to 3.6 pounds of U.08 per cubic foot. In subsequent tests, loaded resin was continuously eluted in a countercurrent elution column with a diameter of 4 inches and containing a bed of resin 9 feet deep. The resin was eluted to a residual loading of less than 0.06 pound of U305 per cubic foot, at a resin-retention time of 224 minutes, using only 1.9 volumes of 1.1 M NaCl-0.05 M NaHCO3 solution per volume of resin. Compared with existing ion exchange practices for recovering uranium from mine waters in the Ambrosia Lake district of New Mexico, use of these improved ion exchange contactors would reduce ion exchange resin requirements at least 70 percent and allow further substantial reductions in capital and operating costs.

Jan 1, 1971

By Walter C. Lorenz

In connection with its renewed study seeking solutions to problems created by release of acid water from bituminous coal mines, the Bureau of Mines recently surveyed reports already written on the subject. This publication is based on that search. The Problem Poor distribution of water is evident on an ordinary geographic map of the United States. The more abundant supplies of surface water appear to be centered in the northeast, the southeast, and the central humid areas of the country. It is in the midst of this abundant surface water, in the Ohio River Valley, that most of the bituminous coal is mined. Varied industry has located in the valley to use the coal and the river. The coal is a source of power and o raw material. The river provides transportation for raw and finished materials; equally important, it provides the water that is used for cooling and processing in manufacturing. It also serves as a vehicle for the disposal of waste.

Jan 1, 1962

By Kyle W. Charlton

The Bureau of Mines utilizes special testing methods for the analysis of underground mine atmospheres for use during or after mine disasters and fires. These methods depend upon drawing sample gas to the surface through multiple tube bundles with the subsequent analysis of grab samples or the automatic analysis by often remotely located instruments on a continuous, 24-hour basis. During cold weather, low ambient temperature causes condensation and freezing of condensable vapors in the sample which can result in delayed response times or complete blockage of the sample line. This report covers research and resulting development conducted by the Bureau of Mines to produce a reliable method to selectively remove condensable vapors and particulate in the sample gas stream under worst-case field conditions. The effort resulted in two prototype systems which have greater field utility than originally anticipated. The innovative project resulted in two patent applications submitted through the Bureau of Mines.

Jan 1, 1981

By Koehler Stout

Many hydraulic backfills are deposited at low density and provide less than optimum support strength to stope walls. This laboratory study shove that fill strength can be considerably increased. Placement methods used to increase the fill strength were the head, vibratory, cementation, double-planed (dblplod), and combinations of these methods. An experimental facility van designed to study the placement cathode and resultant strengths of the fills. Physical property tests made on the fills included laboratory penetration and vane shear plus several supplementary tests, such as grain size distribution and relative density. Test results were compared to fills planed by conventional methods and to those results reported by other investigators. When compared to fills placed by conventional methods, the penetration modulus was increased by 4.3 tines when the uncemented-vibrated-head concept was used and 71 times when the cemented-vibrated-head-dblplod concept was used. Apparently, hydraulically fill strength can be substantially increased. Conceptual mining plans are also included on suggested ways of placing and using high-modulus backfills.

Jan 1, 1979

A study of the electrolysis of PbS in molten PbCl2 showed cathode efficiencies which increased with current density at fixed sulphide concentrations, and decreased with increasing sulphide concentration at fixed current densities. The anodically produced sulphur dissolved rapidly in the melt, the rate increasing with temperature and sulphide concentration. Experiments with diaphragm cells, made to determine the relative effects that dissolution of lead and sulphur have on the cathodic current efficiency, demonstrated that dissolution of sulphur was the major contributor to the lowering in efficiency.

Jan 1, 1973

By Virgil Marple

In the summer of 1979 the University of Minnesota Mobile Laboratory (UMML), designed for the analysis of airborne particles and gases was used to study fugitive dust from an open pit coal mine. The analysis consisted of determining the particle size distribution and concentration of dust from various mining operations, such as blasting, draglines, loading, roadways and bottom scrapers. For some operations the particles size distribution and concentrations were determined at varying distrances. Details of the dust concentration within the plumes as the plume passed the UMML were measured with an optical particle counter. For line sources, such as roadways this enabled the calculation of the particle flux at the sampling location. In addition to the standard instruments associated with the UMML, the applicability of some new instruments were investigated. These included a uniform deposit cascade impactor and a flux meter. Finally, a technique in identifying plume origins which utilized elemental X-ray flourescence analysis of filter samples was shown to be effective.

Jan 1, 1980

Strategic planning in mining is an important value accretive process. One of the most important aspects during the planning phase is determining the correct mine and plant design. The traditional mine site design (mine, plant, stockpiles, dumps) develops a fixed system for one set of conditions or expected values. A robust design is a fixed system that is designed to deal with a large range of conditions without changing the system design. A flexible design changes the system dynamically in response to changes in uncertainties. It is hypothesised that a robust design generates less value than a flexible design as it fails to realise the value of actively managing the operation. One of the most critical aspects in creating strategic value from a project is embedded in the design of the system. A flexible design has components that allow the design of the system to change over time. An operational plan is proposed as a hybrid of a robust and flexible design. This paper seeks to compare these different design methodologies. An analysis of the same case study is undertaken to compare these approaches, showing an a traditional net present value (NPV) of $1678 M, robust design NPV of $1787 M and an operational plan NPV of $1867 M - an increase of $170 M.

Dec 6, 2010

The Bureau has published much data on sulfur (4, 15, 23)3, most of it dealing with national or international aspects of the sulfur industry. Little information, however, is available on sulfur marketing in specific States or areas, Therefore, the Bureau has conducted a survey of the resources, production, consumption, and economic future of the sulfur and sulfuric acid industry in States of the Central and Southern Rocky Mountain area - Wyoming, Colorado, Utah, Arizona, and New Mexico - and in the Northern Plains States - North Dakota, South Dakota, and Nebraska, even though these States do not represent an economic or marketing unit. The purpose of this survey is to review the demand for sulfur and primary sulfur compounds that draws upon the natural resources of the region, to discover opportunities for better use of these resources, and also to analyze and evaluate the patterns of consumption, sources of supply, and other factors that affect the demand for these mineral products. While this survey stresses the economic and marketing phases of the industry, a complementary report (32) emphasizes the resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizona.

Jan 1, 1962