Search Documents

By J. M. Mutmansky, A. Wang

This paper defines the elements of a basic economic model for decision-making when considering a methane drainage system for an underground coal mine. A drainage system will require significant capital and operating expenses; hence the decision to utilize drainage must be made carefully. The model outlines the basic structure of decision-making and considers the costs and benefits when the methane is marketed and when the methane is vented to the atmosphere. The effects on mine safety and the dust levels in the mine are also considered, both in a general format and as economic variables. Sources of information for executing this decision-making are provided for an actual mine decision.

Feb 24, 1997

By Paul J. O'brien, George N. Neary

"The base metal mine at Buchans, Newfoundland, has been producing since 1928. For many years, mill tailings were disposed of by dumping into a nearby natural watercourse via which they were transported to Red Indian Lake and deposited. In 1965, environmental concerns prompted the establishment of settling ponds near the mine site. Effluents fed to these ponds included slimes washed from mine backfill sand and waste water pumped from underground as well as mill tailings. Dusting around the perimeter of the ponds was first observed around 1970and within a couple ofyears reached serious proportions. A program to alleviate the condition by developing a vegetative cover over the tailings was commenced in 1974. The work was successfully carried out and demonstrated that the large area of waste could sustain a permanent cover of grasses.This paper outlines the experimental work done at Buchans as well as the procedures followed and the problems encountered in carrying out full-scale revegetation."

Jan 1, 1981

By Rob Thomas

Adequate load transfer is considered essential for optimum ground support and is increasingly important in weak roof and/or high stress environments. If adequate load transfer is achieved not only can this have a positive impact on the resulting roof behavior, but it may also allow the use of lower and hence more economic densities of roof support. A wide variety of post-groutable cable bolts are currently in use in the Australian coal mining industry, each of varying capacity, design, and grouting methodology. Though all of the cables are supplied with the appropriate steel specification, strength, and modulus data, the Australian coal mining industry does not have access to a comprehensive and comparative database on the corresponding load transfer performance, which is a critical problem. On the basis of the above, this paper describes the methodology and results of a laboratory pull testing program that aims to assess the impact of cable bolt design on load transfer, and specifically, the impact on the capacity and stiffness of the anchorage. As part of the testing program, 19 cables were tested including (1) plain-strand cables installed in holes drilled with 28 to 55 mm diameter drill bits and (2) bulbed and nutcaged cables installed in holes drilled with 42 to 64 mm diameter drill bits. Other parameters assessed included the significance of smooth and profiled wire, wire packing, and expanded geometry bulbs. The main results of the testing indicate that in comparison to plain-strand cables, if the cable is bulbed or nutcaged, the capacity of the anchor can increase by up to 400%, and the peak stiffness by between one and two orders of magnitude. The results also indicate that increasing hole diameter may have a positive impact on load transfer in the case of bulbed or nutcaged cables and a negative impact on plain-strand cables. No conclusive results were obtained with regard to the impact of grout strength on load transfer.

Jan 1, 2012

By William J. Douglas

This document describes the development of a conventional mining equipment data base, and an approach for conducting industrial engineering studies of arbitrary mining systems employing network techniques. Data was acquired through underground time studies. Each member of a four-man field team was assigned to a specific machine during each shift for which observations were conducted. Using digital wrist watches and networks describing the man-machine interactions, all events occurring luring the course of each shift were recorded on cassette tapes. The tapes were transcribed, coded, keypunched, and validated using computerized editing techniques. The resulting data files were processed to provide statistics relating to activity durations and event frequencies. The results were used to evaluate operator, machine, and system performance for each section which was observed. Equipment, reliability, and maintainability analyses were conducted using the industrial engineering data files in conjunction with historical information collected at the mine site.

Jan 1, 1976

By G. Bierie

The conveying of bulk materials is prone to problems. These problems can reduce the capacity and efficiency of the plant, and even threaten the health and safety of the workforce. This presentation will look at new conveyor technologies systems, and how, used separately or in combination, they can improve material handling.

Jan 1, 2007

A review is presented of developments in mill liners to improve performance in terms of wear, impact, as well as mill grind and throughput. These developments are in response to the growth in size of SAG mills and the use of larger ball loadings and ball sizes in modern SAG milling practice. Shell liner developments include specific mechanical design features such as special bolting, directed metal flow to prolong liner life and a focus on the process aspects of the mills to provide more effective grinding motion with reduced wasteful ball-on-liner impacts. Grate design developments aim to provide high throughput of material, especially in the larger size fractions, while providing good impact and wear life. Curved pulp lifters are designed to ensure, at high mill speeds, complete discharge of coarse solids from the mill.

Jan 1, 1999

By Taehong Kim

An accurate and reliable prediction of Tunnel Boring Machine (TBM) performances, in terms of Rate of Penetration (ROP), utilization (U), and cutter wear rate, is a critical element in the successful planning and execution of mechanical tunneling project. Three open hard rock TBM projects were studied to establish possible trends and correlations between rock mass properties and machine performance. Based on this analysis and literature survey, three geological parameters, including RQD, RMR, and groundwater inflow rate, were identified as having the greatest impact on TBM utilization level. Rate of Penetration (ROP) and cutter wear rate were also correlated with fracture spacing, alpha angle, and Cerchar Abrasivity Index (CAI).

Jan 1, 2008

By Yajie Wang

High horizontal stress and its adverse effects on longwall gate entries have been witnessed in many US coal mines for the past years. It can cause cutter roofs and leads to roof falls either in the headgate or tailgate entries depending on the relative orientation of the panel to the maximum principal horizontal stress. Underground observations have shown that if the maximum principal horizontal stress is perpendicular to the panel entries, the roof is in the worst condition and if the maximum principal horizontal stress is parallel to the entries, the entry is in the best condition. However, little has been done about the high horizontal stress effects on panel entries subject to different orientations of high horizontal stress. In order to design a longwall panel and control the roof effectively, the redistribution and concentration of high horizontal stress field must be fully understood. Using 3-D finite element analysis, this paper presents the high horizontal stress redistribution and concentration for a retreat longwall face with different orientations of high horizontal stress. Based on the results, possible roof failures for different orientations of high horizontal stress are analyzed. A panel design criterion is recommended.

Jan 1, 1996

By M Nehring, E Topal

Nowadays mining projects are seeking new versions of evaluation that are based on the flexibility in the project. Real option valuation (ROV) is one of the modern evaluation methods that provides a tool to adapt and revise mining projects under uncertainty and future variable movements. Most evaluation approaches simply assume that some variables are fixed, such as production rate, variable cost, fixed cost and lifetime of project. The first section of this paper reviews a comprehensive study of ROV in mining projects. The paper then introduces a new model that solves problems where previous methods lacked. The new method endeavours to find maximum mining project value by adding total cost as a function of production rate into ROV. The second section has been applied to a new model on the Century zinc mine in north-west Queensland, thus illustrating the future overview of that mine. The new version of ROV gave a significant positive value for the Century Mine, when the closure and reopening options where available throughout the life of the mine. Consequently, the new method evaluates real options to add value to mining projects, maximising projectÆs value, estimating cost function, optimising production rates and offers opportunities in projects to amplify gains or to mitigate losses.

Jan 1, 2009

By Donald R. Johnson

Apparatus providing simultaneous differential thermal analysis, thermo-gravimetry, and evolved gas analysis, has been developed by the Bureau of Mines specifically for thermal study of oil shale and other solid, natural fuels. The apparatus is described in detail, and simultaneous analyses on a single sample of an oil shale mineral, nahcolite, and a thermal analysis demonstration compound, calcium oxalate monohydrate, are presented to demonstrate the instrument's capabilities.

Jan 1, 1970

By Susheel R. Kolwalkar

A significant increase in the side shear capacity over a period of time is often observed in case of driven piles. This phenomenon is referred to as ?setup? or ?freeze?. This phenomenon cannot be predicted based on the knowledge of the engineering properties of soil. Different kinds of mechanisms have been proposed in order to explain set-up in cohesive soils. In engineering practice, set-up is incorporated in design on the basis of empirical formulae and depends to a large extent on personal experience and judgment of the design engineer. Set-up is a natural process which cannot be accelerated by any existing practice. A research was initiated to investigate the mechanism of pile set-up in clayey soils and explore the possibility of accelerating the set-up process by an electro-kinetic method. The system chosen for the present study consists of a prototype steel pile driven in kaolinite clay. A laboratory test program was developed at Cleveland State University in order to meet the goals of the proposed research. Results obtained from these tests are very encouraging and show pile capacity increase of 200% within the first 5 days of electric gradient application versus those that experience natural set-up. In this paper, theoretical considerations and laboratory test results are presented and discussed.

Jan 1, 2008

By George Goble

I hope that after the long evening and all the exercise that some of you took you won't be completely exhausted to listen to a little bit about pile testing. The topic that 1 have been given is pile testing. It seems to me useful to break this topic into some smaller pieces so that we can try and organize our thought a bit. As I understand the terms "pile testing", I believe we are really referring always to capacity, one way or another, so I am suggesting that we organize the things we are doing in terms of measurement of soil capacity and pile capacity. There are obviously two failure modes and we frequently speak of pile integrity rather than structural pile capacity, but it's really capacity that we are concerned about. Further within these breakdowns I am suggesting that we might look at the topic of soil capacity in terms of static methods and dynamic methods and, finally, within each one of these, measurements of axial capacity and measurement of lateral capacity. Also here some of these subdivisions might be there for the purpose of symmetry and finally the same sorts of breakdown in Pile Capacity area.

Jan 1, 1994

By O. K. Olawale, G. O. Edaogbogun, B. N. Ben‑Festus, F. Ben, F. R. Amodu

The environmental and health implications of artisanal gold mining activities at mining sites across Nigeria have rekindled research interest. This study aimed to assess the scalability of naturally occurring radioactive materials in gold mining sites in Iperindo, Nigeria. Soil samples were collected from three different mining sites and control locations and analyzed for natural radionuclides, mainly 238U, 232Th, and 40K, using gamma spectrometry having a sodium iodide detector. The average activity concentration values of 61.55 ± 3.71, 72.65 ± 4.45, and 1134.99 ± 38.12 Bqkg− 1 obtained from within the mining sites for 238U, 232Th, and 40K, respectively, were above the world permissible values of 33.0 Bqkg− 1 for 238U, 45.0 Bqkg− 1 for 232Th, and 420.0 Bqkg− 1 for 40K. The average activity concentration values of 15.26 ± 3.19, 21.46 ± 4.27, 381.04 ± 23.36 Bqkg− 1 estimated for 238U, 232Th, and 40K, respectively, for the control location were, however, lower than the global permissible values. The study also evaluated other radiological parameters such as radium equivalent, dose rate, annual effective dose rate, internal and external hazard indices, and alpha and gamma indices. The obtained values were 252.83 Bqkg− 1, 119.98 nGyh− 1, 147.15 mSvy− 1, 0.85 Bqkg− 1, 0.68 Bqkg− 1, 0.31 Bqkg− 1, and 1.89 Bqkg− 1 respectively. Except for radium equivalent, external and internal hazard risks, and alpha index, which were significantly lower than the recommended threshold, all other radiological parameters were higher than the recommended global limits. Moderate data reproducibility and a p-value of 0.000574 further reinforced the robustness and reliability of the results obtained in this study.

Feb 22, 2024

Study on Iron Ore Sintering with High Proportion of Specularite Concentrates Specularite iron ores have poor hydrophilicity and ballability as well as bad high-temperature reactivity, which restricts the large-scale application in the sinter and pellet production. In order to make the best use of the specularite concentrates, a novel process of Composite Agglomeration Process (CAP) is applied in this research. By the CAP, the percentage of specularite concentrates in the sinter mixture is increased to no less than 40 per cent as well as the coke breeze dosage is reduced by 0.3 per cent~0.6 per cent. Moreover, all the sintering indexes are obviously improved compared with the traditional sintering process. Researches on the metallurgical performances shows the finished composite agglomerates are high-quality burdens for blast furnaces. This investigation can provide an effective route to utilize the inferior specularite concentrates in the sintering.

Sep 13, 2010

By J. C. Duchon

The U.S. Bureau of Mines is conducting human factors research for the purpose of reducing accidents and improving the person-machine interface found in surface and underground mining operations. Miners are exposed to a variety of environmental stressors, e.g., extreme heat, noise, vibration, and adverse illumination, throughout the workday. Exposure to these environmental stressors has been noted in the literature to affect performance on vigilance tasks. Since impaired performance at vigilance tasks can lead to industrial accidents, further investigation of the effects of environmental stressors on human performance is warranted. A brief description of the environmental conditions present in the mining workplace is followed by a review of experiments dealing with the effects of environmental stressors on vigilance task performance. The applicability of past research to actual mining operations is considered.

Jan 1, 1989

By Hamid Maleki

Having developed a methodology for estimating mining-induced seismicity resulting from slip along geological discontinuities in 2003, in this paper, the importance of measurements are high-lighted in the study of caving and seismic source mechanisms as applied to mine designs. Geotechnical data is analyzed from four case studies to address cave condition, load transfer, and potential effects on stability and resource recovery in four Utah mines using measurements and observations conducted over the last three decades. Cave conditions are evaluated on the basis of measurements in the gob of a western U.S. operation mining under the massive Castlegate Sandstone and indirectly using the results of measurements and boundary-element modeling at panel boundaries at a mine where strata behave elastically. Together with subsidence measurements and microseismic monitoring, regional caving and load transfer in multiple-panel extractions are addressed while the effectiveness of barrier pillars in reducing stress and seismic response where mining under massive stratigraphic units is analyzed using measurements and three-dimensional computer modeling.

Jan 1, 2006

This publication summarizes the in-house and contract research and development projects programed for fiscal pear 1980 by the Bureau of Mines under its Minerals Environmental Research activity. The document provides a mechanism for interested parties, including potential contractors, to gain insight into ongoing and projected work of the Bureau's environmental research efforts. Research to identify and correct environmental problems associated with mining and metallurgical operations has long been an integral part of the Bureau's mission. Through the years, efforts of various Bureau programs have yielded valuable information on the origin and control of many of these problems. With the reorganization of the Bureau of Mines in 1979, the Minerals Environmental Technology program was structured to consolidate these efforts into a single program that will systematically investigate al aspects of mining- and processing-related environmental pollution and damage-from initial discovery of the mineral resource to ultimate return of the land to productive use. In fiscal year 1980, the Bureau received an appropriation of about $21 million to conduct research and development work on these problems.

Jan 1, 1980

By B. S. Gottfried

This paper is concerned with possible transport mechanisms which occur during segregated burning (i.e., burning in an oil reservoir in which the oil-bearing formation is overlain by a "clean" porous zone containing only gas). ,Two analytical models are presented. In the first, burning is assumed to occur at the gas-oil interface, and the dominant mechanism is taken to be the rate at which oxygen diffuses to the interface. The second model assumes that combustion occurs within the clean zone, with the dominant mechanism being the mechanism of fuel deposition from the oil-bearing formation to the clean zone. ,Comparison of the results of the analyses with limited experimental data indicates that the latter mechanism is much more plausible. Both models are idealized representations of the actual process and are somewhat conjectural, however, owing to the lack of more definitive laboratory or field data. INTRODUCTION In recent years there has been considerable theoretical and experimental research directed toward understanding the recovery of crude oil by underground combustion. Although two different recovery schemes have been proposed, known as forward and reverse combustion, it is only forward combustion that shows promise of becoming a practical recovery technique.17 Most of the analyses of the forward combustion process have considered it to be pistonlike; i.e., oil is displaced by a vertical combustion zone which, with its ensuing gases, pushes die oil forward as the flame front is propagated through the reservoir.l-8,ll,l2,14-16 However, information gained in field pilot studies indicates that, at least to a certain extent, forward combustion proceeds in a segregated manner in oil reservoirs.10 An ideal segregated system is one in which the oil-bearing formation is overlain by a "clean" porous zone containing only gas. The location of the combustion zone in such a system is not immediately evident, although combustion is believed to occur either at the gas-oil interface or within the clean zone. In either case, the combustion zone may be horizontal and it moves in parallel rather than in series with the produced oil. The purpose of this paper is to explore the likely mechanisms by which segregated burning can occur, and to determine the sensitivity of the resulting models to changes in various physical parameters. Two governing mechanisms are considered: the case of a horizontal combustion zone at the gas-oil interface with the rate of combustion governed by the rate at which oxygen diffuses to the interface, and the case of combustion within the clean zone with the combustion process controlled by the transport of fuel from the oil-bearing formation to the clean zone. Both models are somewhat hypothetical and involve considerable simplification of the actual process. However, the results allow some preliminary understanding of segregated burning which is useful in the absence of more definitive laboratory or field pilot data.

Jan 1, 1967

By P. D. White, J. T. Moss, J. S. McNiel

Results of experimental work on the in situ combustion process were first published in this country in 1953' when Kuhn and Koch described results of a three-well test in Jefferson County, Okla. Shortly there-after Grant and Szasz2 described field studies in Nowata County, Okla., in which several modifications of the basic combustion process were investigated by injection of various oxidizing gas mixtures other than air. In the past five years speculation concerning this method of oil recovery has continued, with a number of interesting papers on various aspects of in situ combustion appearing in the literature3,4,5,6,7. However, only one of these' provided actual engineering information on pattern-type field experiments. The primary objectives of the Oklahoma three-well test were to check operation of specially designed electrical ignition equipment and evaluate problems associated with initiation of combustion in a natural oil sand reservoir. Immediately following successful completion of this test in the Pontotoc sand, plans were activated for a second field experiment to be conducted in the same sand a short distance away. The objective of this second field test1 as to establish a relationship between field observations and information derived from laboratory experimentation and computations. Secondary objectives of the test were to develop operating tech- niques and define operating problems, and to obtain information that would assist in the economic and engineering appraisals of the process. Careful planning was required since this test was designed with the hope of providing basic information on the characteristics and operation of a combustion drive. It was necessary to include test facilities which would not only permit precise control and measurement of the process variables but would also provide sufficient flexibility of control to insure that variables in the combustion process could be studied during the course of the test under a wide range of conditions. In order to accomplish these objectives elaborate instrumentation and several control wells were included in the design of the test installation. This type installation was felt to be well suited for an experimental study, but was in no respect intended as a counterpart of a commercial-scale operation. PRELIMINARY LABORATORY WORK An important objective of the field experiment, as stated previously, has been to obtain reliable data on operating variables which might be compared with similar data obtained in laboratory combustion tests. The value of successful correlations between quantities that can be measured in the laboratory and those obtained in a full-scale commercial venture has been well established for other industrial processes. The difficulty of following a process underground should make such correlations even more essential here. Also. approaching the field test phase of development of in situ combustion, it was considered desirable to precede design of test equipment with laboratory combustion studies under a variety of conditions to establish likely ranges of variables. These included temperature, air injection rate, frontal advance rate and produced gas composition.

Bahrain's oil revenue increased from $337 million2 in 1916 to $378 million in 1977. Despite the increase in value, petroleum receipts made up only 584 of all Government income in 1877, compared with 74% in 1976 and 83% in 1975. Bahrain became an oil producer in 1932 with the discovery of the Awali oilfield, and since that time, the Awali oilfield has produced over 600 million barrels of crude oil. Awali production in 1977 was 21.2 million barrels. Bahrain shares the revenue from the Abu Safah oilfield, located in the Persian Gulf north of Bahrain, equally with Saudi Arabia. Revenue from the Abu Safah oilfield was approximately $179 million or 47% of oil revenues in 1977. Output from the Abu Safah oilfield was 48 million barrels, an increase of nearly 30% over 1976 output. The Bahrain Petroleum Company (BAPCO). the nation's only oil-producing company, was owned 40% by California Texas Oil Corp. (CALTEX and 60% by the Govern¬ment. The Government established Bahrain National Oil Co. (BANOCO) in 1976 to administer the Government's share of BAPCO, oversee exploration concessions, and manage domestic marketing of petroleum products. The Government announced its intention to acquire 100% control of crude oil and natural gas production. CALTEX was to retain complete control of the 250,000-barrel-per-day oil refinery near Sitrah.

Jan 1, 1981