Search Documents

By Denis Labrie

Le minage en profondeur sous contrainte modérée à élevée présente de nombreux défis aux opérateurs et aux ingénieurs de mine notamment au niveau du contrôle de terrain et de l?environnement minier souterrain, pour assurer la sécurité des travailleurs sous terre et la continuité du cycle d?opération. Des conditions de contrainte élevée signifient une pression accrue au front de taille et sur les structures minières tels les piliers de mine et les fins de zone, un risque de rupture violente ou de coup de toit plus élevé, des zones de rupture plus grandes au pourtour des excavations, des charges accrues sur le support de terrain, etc. Le présent article fournit un aperçu du travail fait à l?intérieur du Programme de Contrôle de terrain de CANMET au cours des sept (7) dernières années, entre 1995 et 2001, pour comprendre et suivre l?évolution des niveaux de contrainte à l?intérieur des structures minières. Les propriétés déterminées en laboratoire sur des échantillons rocheux et les prévisions effectuées au moment de la conception sont comparées avec les observations effectuées en chantier à la paroi des excavations et à l?intérieur de la masse rocheuse. La plupart des cas discutés ici montrent une corrélation satisfaisante entre les observations effectuées en chantier d?une part, et les résultats d?essai obtenus en laboratoire et les calculs réalisés lors de la conception d?autre part. Ces observations peuvent donc être considérées comme des moyens relativement sûrs pour vérifier et suivre l?évolution des niveaux de contrainte présents à l?intérieur des structures minières.

May 1, 2002

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H20) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained,4 but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process 75. In. all of the processes suggested for the recovery of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation. OCCURRENCE OF HALITE IN POLYHALITE A preliminary estimate of the amount of halite associated with typical deposits of polyhalite may be derived from drill cores, although it should be remembered that only 50 or 60 core tests have been made in the many hundreds of square miles of the Permian basin. From a mineralogical study of 41 of these cores, Schaller and Henderson6 state: In many of the sections of core that seem when viewed by the unaided eye to consist essentially of polyhalite, both halite and anhydrite are present in greatly varying quantities - with very minor quantities of clay and magnesite.

Jan 1, 1934

The Aluminum Company of America announced a temporary reduction of the operating rate at its primary aluminum plant at Palestine, TX where it is developing a new process to produce aluminum metal by electrolysis of aluminum chloride, Output will be reduced by half to about 7,500 tons per year while some improvements are being made on the chemical segment of the plant. The modifications were expected to take 3 to 4 years to complete. Alcan Alumininum Ltd., a major U.S. supplier of aluminum, reported declaration of force majeure on aluminum ingot shipment commitments following the shutdown of its primary aluminum plants at Arvida, Isle Maligne, and Beauharnois, Que. The shutdowns, which began early in June, resulted from management and labor differences.

Jan 1, 1979

By John Lindsay

"Although diamond mining is a relative newcomer to the Canadian mining industry, with the first diamond mine coming on stream in 1998, Canada is already a significant producer of high quality diamonds. This paper will review diamond production trends and highlight some of the projects currently under development, which have the potential to enhance Canada’s role as a significant diamond producer.Diamond recovery plants generally incorporate well-established mineral processing and recovery techniques, with issues such as product security, cut-off sizes, and diamond preservation becoming important considerations when developing process flowsheets. A diamond processing plant must achieve three key objectives, namely:• Liberation of the diamonds from the host rock;• Separation of the heavy minerals, which include the diamonds, from the host rock;• Recovery of the diamonds from the heavy mineral concentrates.Processing technologies and equipment commonly utilized in diamond processing plants will be reviewed and some of the significant issues associated with each option briefly discussed.Typical process flowsheets will be presented.Finally, an overview of De Beers’ Victor diamond project, located in northern Ontario, will be provided. This potentially significant diamond producer is currently at a pre-feasibility stage of development.DIAMONDS IN CANADAWorld Diamond ProductionCommercial diamond mining commenced in earnest with the discovery of the Kimberley diamondfields in South Africa in the late 1800s, and this resulted in a dramatic increase in the supply of diamonds. As can be seen from figure 1, world diamond production, mainly from South Africa, Angola, Congo, and Namibia, remained relatively constant through the early 1900s until the development of the large Russian kimberlite pipes in the 1950s. Production increased again in the 1960s and 70s with the development of the Botswana mines, but the most significant increase in global production came from the Argyle mine in Australia, which came on stream in 1983 and produced a peak of almost 43 million carats in 1994, representing approximately 40% of the world market. Production from Argyle has since fallen-off as grades have declined and the strip ratio has increased with the deepening of the open pit."

Jan 1, 2003

By M. D. Seke

The flotation response of a Pb-Zn sulphide ore from the Rosh Pinah Mine (Namibia) was studied in the presence of inorganic depressants such as sodium cyanide and zinc sulphate. Poor flotation selectivity was observed in the rougher concentrate of the galena circuit despite the use of a large amount of sodium cyanide. Batch flotation tests have shown that the use of cyanide alone is not efficient for the depression of sphalerite from the Rosh Pinah ore when milling is carried out according to the current plant particle size distribution. The use of both cyanide and zinc sulphate improved the selectivity between galena and sphalerite much better than cyanide alone. Flotation selectivity is limited by the mineralogical texture of the Rosh Pinah ore sample. Microscopic analysis has shown that the presence of sphalerite in the galena concentrate is also due to poor liberation between galena and sphalerite, especially in the middlings. Hence, selectivity could be improved by regrinding the rougher concentrate prior to the cleaning stage. Keywords: sulphide ores, flotation, flotation depressant, mineralogy.

Jan 1, 2005

By Daniel Bennett

There are few methods currently applied towards on-line bulk mineralogical analysis. Yet on-line knowledge of process mineralogy could potentially provide large benefits, such as increased extraction efficiency or resource optimization. The work described in this paper involves the development of radio frequency methods for bulk mineralogical analysis. Some resonances that occur in the radio frequency spectrum are mineral specific, and potentially allow quantitative estimation of mineralogy in an ore stream. Results will be presented on the specific detection of chalcopyrite. Initial quantitative measurements investigating matrix effects have indicated the feasibility of on-line mineralogical estimation using radio frequency techniques.

Jan 1, 2006

By Shosei Serata

The application of conventional rock mechanics methods to complex ground is very difficult. Yet. In most underground mining, the ground is complex. Therefore. conventional methods are not only difficult to apply but are also generally ineffective in improving underground operations. Similarly, conventional rock mechanics instrumentation has not significantly contributed to improvement of mining practice. Rock mechanics instrumentation in underground mining operations is often considered to be" merely an expensive nuisance. A new system of mine instrumentation is changing this traditional view. The new instrumentation method, called the SPDR method, was originally devised by Dr. Shosei Serata to meet the specific requirement of establishing the Stress Control Method of mining upon a solid quantitative foundation. This instrumentation method has contributed substantially to the widespread success of Stress Control mining under widely varying ground conditions in different types of underground mines (1.2.3.4). The instrumentation method provides an effective means for optimizing Stress Control mining patterns, simultaneously achieving reduction in production costs and substantial improvements in safety (5). The principles and methods of the new instrumentation method are described below, with field examples.

Jan 1, 1986

By J Ward, B Rohrlach, B Rosero, J Silva, O Poma

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Alpala copper-gold deposit is a recent, high-grade porphyry Cu-Au discovery located in the Imbabura Province of north-western Ecuador. The deposit lies along the crustal-scale Chimbo-Toachi Fault Zone within the Dagua-Piñon terrane, which is an oceanic plateau accreted to the South American convergent margin in the Late Cretaceous. The deposit is hosted by quartz diorite stocks that intrude andesitic volcanic breccias of the Oligocene to mid-Miocene San Juan de Lachas Formation. Miocene-age calc-alkaline plutonism is associated with porphyry Cu, Cu-Mo and Cu-Au deposits in southern and northern Ecuador. The Alpala deposit lies along a sector of the Miocene arc that has recently been underplated by the Carnegie Ridge seamount chain that induced shoaling of the subducted Nazca plate beneath northern Ecuador.Surface expressions of the deposit were recognised in May 2012 during follow-up of stream sediment anomalies, when outcropping sheeted and stockwork porphyry-related veins were discovered in Quebrada Alpala. The roots of a NW-trending, structurally-controlled lithocap were recognised over an area of 4.5 × 0.9 km. The remnant lithocap exhibits well-defined mineral zonation mapped by TerraSpecTM analyses on grid soil samples. Soil sampling, heliborne magnetic surveying and channel sampling defined initial drill targets.Seven diamond drill holes were completed in the year from September 2013. Drill hole CSD-13-005 intersected 672 m grading 0.93 per cent Cu and 0.91 g/t Au in high-temperature, inner propylitic and locally potassic-altered quartz diorite intrusions. Overlying hydrothermal clay alteration assemblages define the base of the lithocap. A NW–SE trending footwall structure defines the south-west margin of the deposit. Drill hole 5 intersected high-grade sheeted ‘B-type’ and ‘C-type’ veins (Gustafson and Hunt, 1975) that lie along the south-west margin of an 1100 × 500 m magnetic anomaly that is the focus of ongoing exploration.CITATION:Rohrlach, B, Poma, O, Rosero, B, Silva, J and Ward, J, 2015. High-grade porphyry copper-gold mineralisation in north-west Ecuador – The Alpala Cu-Au porphyry discovery , in Proceedings PACRIM 2015 Congress, pp 369–376 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By A. M. Richardson

The significance of a massive sandstone unit in the immediate roof to longwall support weighting is well known. If the unit lies in the main roof above the zone of caving, its influence becomes more difficult to calculate using traditional methods. Much of the reserves at Cyprus Plateau's new, multi-seam Willow Creek Mine are located in the A Seam. The massive Kenilworth Sandstone is typically situated 21.3 m (70 ft) above the A Seam in the main roof and is on average 14.6-m (48-ft) thick, ranging to 29.0-m (95-ft) thick. This paper describes the application of distinct-element modeling to determination of the appropriate yield capacity for supports at Willow Creek. The modeling was determined to be useful for understanding support loading mechanisms and as an aid to engineering judgment in selecting supports.

Jan 1, 1996

By M. Q. W. Jones

This paper summarizes important features of a compilation of thermal properties of stratified rocks from Witwatersrand gold mining areas. The database consists of more than 1000 thermal conductivity measurements, more than 700 density measurements, and nearly 100 heat capacity measurements. Most important rock types and stratigraphic units are well represented. Heat capacity does not differ significantly from one rock type to another, and density is relatively uniform although particular rock types are characterized by distinct average values. Different rock types also have distinct thermal conductivities, but this parameter varies by a factor of four to five. Primary factors controlling the thermal properties are mineral composition, degree of metamorphism, and porosity. In addition, the temperature dependence of thermal conductivity and heat capacity of quartzite may significantly decrease the thermal diffusivity of this rock at deep mining levels.

Jan 1, 2003

By Verónica Rueda

El proceso de explotación de la Minera Rayrock se inició hace seis años a tajo abierto y ahora comprende las etapas de extracción del mineral, chancado, aglomeración, lixiviación, extracción por solventes y electro-obtención. En ese sentido, el presente trabajo describe el avance del proceso de extracción en el proyecto minero Ivan, perteneciente al yacimiento de la minera Rayrock a través de las técnicas de lixiviación de minerales oxidados y sulfurados de cobre y del manejo innovador en las operaciones de extracción por solventes y electro-obtención.

Sep 13, 2001

By Y. Özçelik

Rocks show a variety of engineering and physical properties that affect typical quarry operation such as diamond wire cutting in the marble quarry. The physical and mechanical properties of rocks depend on their mineralogical and petrographical characteristics. The purpose of this study is to investigate the effects of mineralogical and petrographical properties of a rock, such as grain size and mineral content, and how these affect the wearing of diamond bead and cutting rate in a diamond wire cutting operation in a marble quarry. Statistical analysis is used to carry out the study. Three different rock types were examined, namely, hard rock (andesite) and softer rocks like limestone and marble. The study revealed that the mineralogical and petrographical properties of the rocks, such as percentage of quartz, biotite, plagioclase, matrix minerals, and opaque minerals, are important. In addition, the grain size of quartz and plagioclase in andesitic rocks and calcite grain size for carbonate rocks significantly influenced the wear rate and cutting rate in diamond wire cutting operations.

Jan 1, 2005

By Phil N

A large number of experiments have been carried out by many workers on the recrystallization of deformed and subsequently annealed metals and alloys. Although observations on single crystals are of great importance in the study of the recrystallization textures of deformed and annealed metals, very little of this work deals with material in this form.Since, in deformed metals, the stress concentration is greatest at the grain boundaries and along the planes of slipping, it is to be expected that recrystallization will start in these regions. For example, in polycrystalline aluminium (1),:1: (2), copper (3), a-iron (4) and brass (5), (6), which had been deformed by cold-rolling, drawing, pressing or stretching and then annealed, the new grains first appeared in the boundaries of the original crystals, whilst in the case of cupronickel (7) and iron (8), recrystallization commenced along the slip planes of the deformed material. Deformed and annealed single crystals of aluminium (9) and cadmium (10) first start to recrystallize along slip planes and in deformation twins.The present work deals with the process of recrystallization of single crystals of lead after deformatjon by creep.Two factors enter into these experiments that were not met with in other work on this subject. Firstly, lead...

Jan 1, 1940

By Bernard Lewis

This report on the research and technical studies conducted by the Explosives Branch of the Bureau of Mines covers the 2-year period July 1, 1946, to June 30, 1948. A report for the fiscal year 1947 was omitted because of the large amount of work still in an unfinished state. The material presented herein is based largely upon more comprehensive reports prepared under the authorship of members of the branch staff.

Jan 1, 1949

By Irving Hartmann, John Nagy

"The pressures produced by dust explosions are frequently so great and are developed so rapidly that widespread destruction of manufacturing equipment and buildings results. Experimental data on maximum pressures and rates of pressure rise produced in a closed vessel by numerous metal powders and by dusts used in the plastics industry were published in two previous Bureau of Mines papers.4/5/One means for reducing structural damage is provision in the enclosing walls and/or roof of rapidly opening explosion-relieving devices or relief vents through which the pressure of an incipient dust explosion can be quickly dissipated. The vents can be simply unrestricted or free openings: hinged or pivoted sash which swing outward at a predetermined internal pressure; fixed sash, with light wall anchorages; scored glass panes; light wall panels; monitors or skylights; poppet-type vent closures; paper, metal foil, or other diaphragms that burst at low pressures; pull-out diaphragms, or other similar arrangements.The use of pressure-relief vents is recommended in the dust-explosion codes of the rational Fire Protection Association,6/ and recently a special committee on explosion venting has been organized. However, technical data on which the design and distribution of relief vents can be based are meager. An experimental study on venting grain-dust and cornstarch explosions was made by the Bureau of Chemistry and Soils, United States Department of Agriculture.7/ Tests on cork fines, cinnamon, starch, barley dust, and a phenolic plastic were made in a laboratory-scale (0.1-cubic-foot) apparatus by the engineering department of the Factory Insurance Association.8/ A study on the venting of explosions of acetone-air mixtures was made by the Bureau of Mines.9/The object of the present investigation is to extend the limited knowledge on the effectiveness of pressure-relief vents of different types, shapes, and sizes. The aim is to determine the venting requirements in equipment and structures of various dimensions and shapes for dusts of widely different explosive properties. On the basis of such accumulated information, together with theoretical considerations, it is hoped that ultimately it will be possible to recommend correct venting for most operations in which a dust-explosion hazard exists."

May 1, 1946

By P. H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior around underground excavations made in the mine. The aim of this study was to investigate the geotechnical behavior around a tunnel excavated in a metal mine in China at the three-dimensional level. Using the information available on lithology, geological structures, in-situ stress measurements, physical and mechanical properties of intact rock, discontinuities and interfaces between different rocks, a three-dimensional numerical model was built by using the 3DEC software to simulate a tunnel excavation under a high in-situ stress condition. Effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or continuum material and rock support system on the deformation, stress, failure zone and stability around the tunnel was investigated. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses.

Jan 1, 2012

By J. D. Appleton, J. Ridgway, K. B. Greally

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The results suggest that meaningful geochemical maps can be produced from very low-density surveys, and that existing data sets could perhaps be incorporated into such a map series with the use of a system such as Uniras software. There are still many problems to be resolved, however, including the compatibility of data derived from different analytical methods, and the precise methods to be employed will necessarily require international agreement. Sampling densities should be chosen on the basis of the scale of the geochemical and geological features to be distinguished and will vary from region to region. Reanalysis of selected samples from archives to increase the range of elements determined or to unify analytical methods is only likely to be effective if the original survey was at quite a low density

Jul 1, 1991

A new test coke oven of 7 cu. ft. capacity is described. The oven was designed to simulate conditions in a central section of a battery oven and a special feature is the achievement of unidirectional heating from theflues on either side of the charge.The method of charging permits close control of charge conditions such as bulk density and moisture content.These conditions, as well as coking conditions (e.g. flue temperatures and coking time) must be varied to simulate conditions in different batteries. The effects of several variables on coke quality are discussed.Using test oven conditions corresponding to those of Newcastle steelworks batteries, good agreement was obtained between strength indices of test oven and battery cokes. For 17 tests, the average ASTM stability and hardness indices for the test oven coke were 38· 5 per cent and 69·7 per cent, while those for the battery coke were 37· 4 per cent and 67·6 per cent.Observed relationships between coke yield and productivity, and volatile matter and charge moisture are given.The use of a test oven to classify test coals into prime-, medium-, poor-, and non-coking coals is discussed.This may be achieved by observing the effects of the test coal in blends with other coals. The results of a series of blending tests are presented.The dangers of attempting to predict coke quality from a single coal property are pointed out, since this can be done only for very restricted ranges of coals.A diagram is given showing the established trends in the effects of blending various types of Australian coals on coke strength.

Jan 1, 1970

By E. Marcoux, F. Lotfi, A. Belkabir, L. Maacha, A. C. Brown, S. Brunet

"Koudiat Aïcha is a small Zn-Pb-Cu deposit, enclosed in the Visean Sarhlef volcano-sedimentary series of the Moroccan Hercynian Jebilet massif. Base metal mineralization is located between a basal unit consisting of black argillite with arenite intercalations, and an upper unit composed of black argillite with locally fossiliferous calcareous units towards the top. Paraconcordant gabbro sills are present in both the upper and basal units, and the enclosing strata. Three successive phases of deformation linked to regional deformation overprint the volcano-sedimentary rocks and gabbros, as well as the sulfide mineralization.The mineral deposit includes several lenses of massive to semimassive pyrrhotite, 1 to 20 m thick, with a large halo of disseminated sulfide veinlets and sulfide nodules within a zone of intense chlorite alteration in the footwall. The ore mineralogy consists of massive to semimassive pyrrhotite with lesser amounts of sphalerite, chalcopyrite, arsenopyrite, galena, pyrite, and stannite.Lead isotope results (206Pb/204Pb averaging 18.27) suggest that the metals of the Koudiat Aïcha deposit are derived from the volcano-sedimentary host rocks. Sulfur isotopes also indicate a volcano-sedimentary origin, with bacterial reduction of sulfate (d34SCDT = -7.5‰ to -10.5‰). The conditions for sulfide meta-morphic equilibration range from 250° to 330°C (sphalerite and chlorite geothermometers). The gabbroic sills could have been a local heat source for hydrothermal circulation. Based on these geological and mineralogical features, a Besshi-type model seems appropriate for the genesis of the Koudiat Aïcha mineralization.Koudiat Aïcha est un petit dépôt de Zn-Pb-Cu, encaissé dans la série volcano-sédimentaire Viséenne de Sarhlef dans le massif Hercynien de Jebilet au Maroc. La minéralisation en métaux usuels se situe entre une unité basale d’argilite noire interlitée d’arénite et une unité supérieure composée d’argilite noire comprenant localement des calcaires fossilifères près de son sommet. Des sills de gabbro paraconcordants sont présent à la fois dans les unités basale et supérieure, ainsi que dans les strates environnantes. Trois phases de déformation successives associées a la déformation régionale superposent leurs effets sur les roches volcano-sédimentaires, les gabbros, ainsi que la minéralisation sulfurée. Ce gîte comprend plusieurs lentilles de pyrrhotite massive a semimassive de 1 a 20 m d’épaisseur au sein d’un large halo de veinules de sulfures disséminés et en nodules au sein d’une zone intensément chloritisée dans le mur du gisement. Le minerai consiste en pyrrhotite massive à semimassive avec des quantités subordonnées de sphalérite, de chalcopyrite, d’arsénopyrite, de galène, de pyrite, et de stannite. Les résultats de l’analyse des isotopes du plomb (206Pb/204Pb moyen de 18.27) suggèrent que les métaux du gîte Koudiat Aïcha proviennent des roches volcano-sédimentaires encaissantes. Les isotopes du souf¬fre indiquent eux-aussi une origine volcano-sédimentaire, impliquant la réduction bactérienne des sulfates (d34SCDT = -7.5‰ et -10.5‰). L’équilibration métamorphique des sulfures s’est produite entre 250° et 330°C (géothermomètres à sphalérite et chlorite). Les sills de gabbro pourraient avoir été la source de chaleur locale responsable de la circulation hydrothermale. Sur la base de ces caractéristiques géologiques et minéralogiques, il semble approprié d’invoquer un modèle de type pour Besshi pour expliquer la genèse de la minéralisation de Koudiat Aïcha."

Jan 1, 2008

By M Stevens, M P. Simpson, J L. Mauk

The Karangahake deposit was the second largest producer of gold-silver bullion in the Hauraki Goldfield, New Zealand. New mapping of a 2 + 3 km (6 km2) area demonstrates that hydrothermal alteration surrounds productive veins. Wallrocks proximal to veins are intensely altered and alteration decreases toward the margin of the system.   At Karangahake, distinct zonation of adularia, calcite, epidote, illite and illite-smectite surrounds gold-bearing lodes with unaltered rocks containing magnetite and plagioclase occurring on the margins. Adularia, illite, illite-smectite, and calcite zonation defines hydrothermal alteration extending 2 km to the east of productive lodes. Epidote and adularia zonation occurs proximal to veins. The adularia zone compares well to potassium/thorium studies conducted in the area. Illite zonation is well developed to the east of the veins grading into interstratified illite-smectite containing 5 to 40 per cent smectite 1.5 km from the Maria Lode. Calcite is restricted to the east of the study area occurring in 18 per cent off surface samples. Less altered rocks containing plagioclase and magnetite occur distal to veins. The magnetite occurrence compares well to aeromagnetic studies conducted in the area.   Adularia and coexisting adularia and albite indicate the host rocks were highly permeable. Epidote, illite, illite-smectite and previous fluid inclusion evidence implies temperatures graded from >240¦C in the core of the system to approximately 150¦C on the periphery. The alteration association of quartz, adularia, calcite, pyrite, chlorite, illite and illite-smectite reflects a near-neutral to weakly alkaline water. Calcite occurrence and the absence of zeolite imply the fluid contained significant dissolved CO2.

Jan 1, 2005