Search Documents

By I. Sedat Buyuksagis, Jamal Rostami, Ali Naeimipour

"Improving the safety of underground openings and optimizing ground support systems requires reliable ground characterization. This includes understanding the joints, discontinuities, and rock strength. Joint information can be obtained from borehole cameras, but measuring in-situ rock strength is very difficult. Use of borehole probes can be an ideal and efficient way to meet this requirement. This paper discusses the development of the Rock Strength Borehole Probe (RSBP) and presents the preliminary laboratory/field test. This device can be an accurate, flexible, quick, non-disruptive, and cost-effective alternative to estimate the rock strength inside boreholes in underground mines and tunnels. In addition, the scratch testing procedure in the laboratory by means of a newly developed miniature linear cutting machine is explained. Based on the results of these tests, two equations are developed to estimate the uniaxial compressive strength (UCS) and Brazilian tensile strength (BTS) of the sedimentary/metamorphic rocks. These equations, are based on testing 27 different sedimentary, igneous, and metamorphic rocks by full-scale scratch tests, including the cutting tests by a miniature disc. The results show a good correlation between the normal force and the compressive strength of sedimentary rock if the depth of the scratch is known. No significant correlation was observed for igneous rocks, due to the impacts of grain size.INTRODUCTIONEstimated rock mass properties are essential input for geomechanical studies and stability analysis for any structure constructed in or with rock. The availability of geological information is the crucial component of rock mass classification. One of the important parameters in evaluating rock mass properties is the intact rock strength. This parameter is usually measured by testing the core samples, obtained from exploration boreholes. These samples are subsequently tested in geomechanics laboratories. The test results offer limited information about the rock at the few boring locations despite all the efforts and costs. In addition, these results may not necessarily be representative of the behavior of the rock in the field as the test cannot provide the insitu condition of the ground."

Jan 1, 2016

By Bruna de Camargo Lemos

O objetivo deste trabalho compreende a realização da síntese de SnO2 dopado com aditivo Sr2 contendo diferentes quantidades molares de SrO (X)SnO2+(1-X)SrO, em que o cátion Sr2+ foi introduzido através do nitrato de estrôncio variando de 5 à 50 % em mol para uma mistura tanto em meio aquoso quanto em meio alcoólico, seguida da calcinação do pó resultante que é feita à 700°C com uma taxa de 10°C/min. Análises de caracterização como difração de raios X, área específica, calorimetria exploratória, picnometria a gás e determinação do ponto isoelétrico das suspensões aquosas foram realizadas de modo a verificar qual o agente dispersante mais apropriado para as características ácido-básicos da suspensão em questão. A partir deste determinar o potencial zeta do composto estudado através da eletroforese. Compostos intermediários a base de estanato de estanho foram identificados, e a deposição por eletroforese foi realizada com sucesso, uma vez que foi possível obter uma suspensão estável a partir dos pós cerâmicos produzidos.

Aug 16, 2017

By B. Ignasiak

Laboratory studies suggest that improvements of coke strength brought about by pre-heating caking coals before carbonization accrue from inadvertent oxidation rather than from other low-temperature changes in the coal mass. Controlled oxidation of highly caking coal, followed by laboratory carbonization, produces cokes which, in terms of a laboratory scale tumble test index, are equivalent to those obtained from prime metallurgical blends. Appropriately formulated blends of exhaustively oxidized and fresh caking coal similarly yield cokes with strength indices comparable to those of cokes made from the same coal after oxidation under optimum conditions.

Jan 1, 1979

By Sherwin F. Kelly

FRONTIERS of geological knowledge retreated further this past year before an ever-widening geophysical attack, as governments and endowed institutions continued to take an increasing practical interest in the geophysical line of approach to the study of earth phenomena. A year ago I opened this annual review with a brief account of the efforts to discover what formations lie concealed beneath the deep sediments which form the superficial portions of the Continental Shelf off the eastern United States. That work was but the beginning, and 1938 saw its continuation and expansion. With the assistance of a Guggenheim Fellowship, Maurice Ewing pushed his researches in the development of instruments and techniques for deep-sea seismic refraction studies. Ewing's early refraction profile from the Virginia Capes to the edge of the Continental Shelf has been followed by a similar traverse in Great Britain from the coast of Cornwall to the edge of the Continental Shelf southwest of England. This showed that the thickness of the sedimentary mantle and the rates of slope of the basement surfaces there are comparable to those in the Virginia Cape district.

Jan 1, 1939

By John S. Dunning

This paper is one of a series describing methods and costs of recovering sand and gravel from deposits in the United States and deals directly with the operations of the Atlas Sand, Gravel and Stone Co. at Farmington, Conn. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local expenditures only and not total production costs. It is recognized that publication of total costs might in some instances cause embarasement to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations may ensue.

Jan 1, 1933

By J. Lampke

The superior characteristics of iron ore pellets compared with natural ore and sinter are well known. Due to the higher grade and bulk density they show improved transport and material handling properties. While charging blast furnaces with pellets an increased productivity is realized through pellet?s uniform structure and composition. The increased productivity is caused by a high permeable furnace burden with a decreased coke usage via fuel injection and oxygen enrichment. Therefore, a narrow pellet size distribution and a minimum content -6.3 mm are necessary (Meyer, 1980). The required pellet size distribution can be achieved on the one hand by screening the fired pellets after the induration furnace and recycle the undersized pellets. On the other hand it is possible to produce high quality iron ore pellets with a high degree of sphericity, the important narrow grain size distribution ranging between 9 to 16 mm with high green strength directly in the pelletizing device. To produce high quality green pellets, possibilities and knowledge about adjustments of the pelletizing device are necessary. The paper presents a classification of state of the art pelletizing systems in accordance with the advantages of the pelletizing disc and pelletizing drum in issues like adjustability, green pellet quality, the recycling rate and the space requirement. By a systematization of the influences on pelletizing the common reliance of objectives on influence like pelletizing moisture, disc inclination, rotational speed, mass flow and rim height are given. A variety of industry-proven examples are shown, too. Keywords: Pellet, iron ore, pelletizing, pelletizing disc

Sep 1, 2012

By Johne Jesus Mol Peixoto

No modelamento matemático do reator RH, a penetração do gás no líquido na perna de subida é o fator chave para determinar a distribuição do gás injetado e obter uma previsão confiável da taxa de circulação do líquido entre a câmara de vácuo e a panela. Neste trabalho, através de simulações numéricas via CFX, investigou-se o efeito das forças de arrasto, de sustentação, de lubrificação da parede, dispersão turbulenta e de massa virtual. A distribuição do gás na perna de subida e os valores de taxa de circulação previstos via CFX foram validados com resultados de modelo físico. A melhor predição da penetração do gás e da taxa de circulação foi obtida na simulação com incorporação da força de massa virtual e da força de sustentação, cujos coeficientes foram iguais a 0,3 e 0,1, respectivamente. A força de lubrificação deve ser utilizada para evitar o acúmulo de gás próximo às paredes da perna, mas possui efeito desprezível sobre a taxa de circulação. Os resultados dos modelos físico e matemático se ajustaram com a equação de Kuwabara para taxa de circulação.

Oct 30, 2017

By Kalyani Devabhaktuni, Mike Minton, Mark T. Howe, Yan Zhang

During the procurement phase of a Design-Build (DB) project, design-build contractors must often commit to a fixed price based on limited or incomplete geotechnical information. This lack of information can result in an inaccurate assessment and allocation of project risk to either the contracting authority or the DB contractor. This paper presents a case study of an elevated water tank supported by mixed ground improvement techniques, including Vibro-Compaction (VC), Aggregate Piers (AP) and Compaction Grouting (CG) in East St. Louis, Illinois. An adaptive design and contracting approach provided the best value solution for a complicated set of geotechnical problems, including static bearing capacity and settlement concerns as well as liquefaction induced settlement. Close cooperation between the owner, the tank contractor, the geotechnical engineer and the ground improvement contractor was essential to produce an effective solution. Ground Improvement techniques resolved the geotechnical challenges at the site through adaptive design methods, utilizing progressive rounds of verification and real time data acquisition to achieve performance objectives. This paper details the evaluation of geotechnical criteria, the selection of ground improvement techniques, the adaptive design and implementation of ground improvements, as well as contracting methodologies used to ensure that the best value was provided. PROJECT INFORMATION In November, 2016, CB&I Storage Tank Solutions (McDermott) submitted a design/build proposal for an elevated water tank for Illinois American Water Company (IAW) in East St. Louis, Illinois. The purpose of this tank was to have backup water capacity for power generation. In the RFP, IAW requested two alternate styles of tank: Option 1, a 1250 Million Gallon (MG) Composite Elevated Tank or Option 2, a 1250 MG Waterspheroid tank. Option 1 consisted of a steel tank supported on a concrete tower. Option 2 consisted of a steel tank supported on a steel shaft. The height (determined by IAW) was 140 feet to the top capacity line measured from top of floor slab.

Jan 1, 2019

By João Alberto Fioresi Altoé

Nas indústrias petroquímicas, nucleares e farmacêuticas o avanço tecnológico tem como objetivo a segurança e confiabilidade dos equipamentos com relação à resistência mecânica e à corrosão. Atualmente, o uso dos aços inoxidáveis superausteniticos é uma solução interessante, para uma maior vida útil dos componentes industriais submetidos a ambientes agressivos, como em meios salinos. Esse trabalho tem como objetivo investigar o aparecimento de pites em um aço comercial superaustenitico de composição química aproximada 25Cr28Ni4Mo em solução salina de cloreto de sódio. O aço foi fundido e tratado termicamente por solubilização a 1050ºC por 1h com o objetivo de eliminar os precipitados. As análises microestruturais antes e após os ensaios de corrosão foram feitas por microscopia óptica e eletrônica de varredura. Observou-se com os ensaios eletroquímicos de Polarização linear e impedância, que o aço inoxidável superaustenítico apresenta excelente resistência à corrosão em meio salino, caracterizado também pelas imagens que não revelaram a formação de pites, mesmo quando submetidos a elevados potenciais.

Aug 16, 2017

By I. R. Kramer

[The final paper in the diffusion symposium was given by I. R. Kramer. The author called attention to the diffusion characteristics of chromium deposited on the surface of steel by treatment with chromium chloride and alloyed with the surface layer of the steel by thermal treatment. As the data cited were previously published in the paper " Chromizing of Steel," by I. R. Kramer and Robert H. Hafner (Metals Technology, October 1942, and in the Transactions, volume 154, 1943, pages 415-420), it is unnecessary to reproduce these data here. The following paragraphs are taken from the author's presentation.— Editor.] Aside from the well-known practical application of the diffusion phenomena to carburizing and calorizing, -diffusion also finds application in adding alloying elements to the surfaces of steel parts. The chromizing of steels is a process by which the surface of a low-alloy steel may be enriched with chromium to form a highly corrosion-resistant case; This chromized case differs from an electroplated coat in that it is a diffused layer integral with the base metal and has all of the properties of a high-chromium steel. Recently a method of chromizing has been developed in Germany by Daeves, Becker and Steinberg in which gaseous chromium chloride and hydrogen are passed over the steel at temperatures of 1650° to 1800°F. The chromium chloride reacts with the iron to give chromium and iron chloride. The chromium atoms are deposited on the surface and diffuse in as the iron atoms diffuse out, forming a layer rich in chromium. The principal role of hydrogen is to remove the carbon from. the surface of the steel. Of the two mechanisms, chemical reaction and diffusion, the one operating at the slower rate will determine the rate of formation of the layer. In this case, diffusion is slower and therefore any factors influencing its rate will affect the process. The rate of diffusion is influenced by the temperature and crystal structure of the parent metal. Depth-concentration studies show that the concentration falls off gradually for a considerable distance and then drops sharply at about 13 per cent chromium, the point coincident with the boundary of the gamma loop. The influence of the composition of the base metal upon diffusion is quite important. The depth of penetration of the chromium decreases as the carbon content increases and, of more importance, the chromized layer becomes brittle and is likely to spa11 if the carbon content is too high. It appears that in order to chromize successfully the carbon must be fixed by strong carbide-forming elements such as chromium or molybdenum, which decrease the diffusion of carbon. If this is not done, the carbon will diffuse from the interior faster than the chromium can diffuse inward, thus forming a carbide barrier. The corrosion resistance of the chromized layer is high, and these steels offer some unique advantages over other corrosion-resisting coating or alloys. While chromizing is not meant to replace stainless steels, it may serve in the saving of alloying elements. The chromizing process uses soft or low alloyed steels that can be easily hot or cold formed and since the chromized layer is soft and firmly adherent, chromized parts can be subjected to cold deformation without spalling or chipping and without loss of corrosion resistance.

Jan 1, 1944

By I. R. Kramer

[The final paper in the diffusion symposium was given by I. R. Kramer. The author called attention to the diffusion characteristics of chromium deposited on the surface of steel by treatment with chromium chloride and alloyed with the surface layer of the steel by thermal treatment. As the data cited were previously published in the paper " Chromizing of Steel," by I. R. Kramer and Robert H. Hafner (Metals Technology, October 1942, and in the Transactions, volume 154, 1943, pages 415-420), it is unnecessary to reproduce these data here. The following paragraphs are taken from the author's presentation.— Editor.] Aside from the well-known practical application of the diffusion phenomena to carburizing and calorizing, -diffusion also finds application in adding alloying elements to the surfaces of steel parts. The chromizing of steels is a process by which the surface of a low-alloy steel may be enriched with chromium to form a highly corrosion-resistant case; This chromized case differs from an electroplated coat in that it is a diffused layer integral with the base metal and has all of the properties of a high-chromium steel. Recently a method of chromizing has been developed in Germany by Daeves, Becker and Steinberg in which gaseous chromium chloride and hydrogen are passed over the steel at temperatures of 1650° to 1800°F. The chromium chloride reacts with the iron to give chromium and iron chloride. The chromium atoms are deposited on the surface and diffuse in as the iron atoms diffuse out, forming a layer rich in chromium. The principal role of hydrogen is to remove the carbon from. the surface of the steel. Of the two mechanisms, chemical reaction and diffusion, the one operating at the slower rate will determine the rate of formation of the layer. In this case, diffusion is slower and therefore any factors influencing its rate will affect the process. The rate of diffusion is influenced by the temperature and crystal structure of the parent metal. Depth-concentration studies show that the concentration falls off gradually for a considerable distance and then drops sharply at about 13 per cent chromium, the point coincident with the boundary of the gamma loop. The influence of the composition of the base metal upon diffusion is quite important. The depth of penetration of the chromium decreases as the carbon content increases and, of more importance, the chromized layer becomes brittle and is likely to spa11 if the carbon content is too high. It appears that in order to chromize successfully the carbon must be fixed by strong carbide-forming elements such as chromium or molybdenum, which decrease the diffusion of carbon. If this is not done, the carbon will diffuse from the interior faster than the chromium can diffuse inward, thus forming a carbide barrier. The corrosion resistance of the chromized layer is high, and these steels offer some unique advantages over other corrosion-resisting coating or alloys. While chromizing is not meant to replace stainless steels, it may serve in the saving of alloying elements. The chromizing process uses soft or low alloyed steels that can be easily hot or cold formed and since the chromized layer is soft and firmly adherent, chromized parts can be subjected to cold deformation without spalling or chipping and without loss of corrosion resistance.

Jan 1, 1944

By D. B. Dreisinger, D. G. Dixon, G. Nazari

"The kinetics of chalcopyrite leaching in acidic ferric/ferrous sulfate media under atmospheric conditions in the presence of pyrite has been investigated. It has been found that pyrite samples from different sources affect the rate of chalcopyrite leaching differently. A strong correlation between the amount of silver associated with the pyrite and its effectiveness has been noted. In this study, improvement of the catalytic properties of pyrite such that all pyrite samples accelerate the rate of copper extraction regardless of their sources is demonstrated, and a detailed discussion of the mechanisms involved in the process of chalcopyrite leaching in the presence of silverenhanced pyrite is presented. INTRODUCTIONIt is well known that chalcopyrite resists leaching in sulfate media. It has been proved that pyrite facilitates the leaching of chalcopyrite (Berry et al., 1978; Dixon et al., 2008; Mehta and Murr, 1983; Muñoz et al., 2008; Nowak et al., 1984, Tshilombo, 2004). Considering the catalytic effects of pyrite on accelerating the kinetics of chalcopyrite leaching, Dixon and Tshilombo (2005) have developed a new process, known as Galvanox™, which has several advantages over other hydrometallurgical processes. Galvanox™ runs under atmospheric conditions, so it requires only low-cost leaching tanks. The sulfur yield at this temperature is high (>95%) which leads to low oxygen consumption and low sulfuric acid generation. The operating temperature is below the melting point of sulfur which eliminates the use of surfactants. This process also does not require fine grinding. Reaction 1 shows the overall leaching reaction in the Galvanox™ process.CuFeS2 + O2 + 2 H2SO4 = CuSO4 + FeSO4 + 2 S0 + 2 H2O (1)Complete copper recovery from the Galvanox™ process can be achieved at a considerably higher rate than other atmospheric ferric sulfate leaching processes (Dixon et al., 2008). Recycling pyrite and recovering copper from tailings with the Galvanox™ process have also been evaluated in continuous pilot leaching campaigns (Dixon et al., 2007)."

Jan 1, 2012

By S. Caron

From the early 70?s, ?Centre de Recherche Minérale? (CRM) has conducted and co-ordinated Research and Development activities for the mineralurgical and metallurgical industries. Since 1999, CRM has continued its mandate through COREM which is a consortium of 13 members that uses the benefits and advantages of collaborative pre-competitive industry / university research. In particular, COREM?s ?In-Situ Optimization Group? is involved in the implementation of modern optimization and control tools. The POP Project was launched in order to increase and consolidate the use of modern optimization and control tools and methods for mineralurgical and metallurgical processes. To ensure a successful transfer in the industry, there are a number of essential activities that have to be undertaken. These activities have been identified by COREM?s members and are grouped into three main modules: - R&D Module: Research and Development in universities, research centres and other partners; - Technology Transfer Module: integration of new tools and methods into the POP Software, industrial applications and technical support; - Training Module: education of new engineers in universities, continuing education of plant personnel through on-site workshops and resource networking by specific information exchange tools. This paper outlines the opportunities that led to the definition of the POP Project and describes its main modules. The main features of the POP Software are presented, the first application is described and finally, future developments are discussed.

May 1, 2001

By RENARDIR PEIXOTO MACIEL JUNIOR

A importância do desenvolvimento sustentável, tendo como base um ambiente saudável para as gerações futuras, leva a se pensar em como as organizações poderiam desenvolver materiais menos danosos ao ambiente com boas propriedades e pelo menor custo. A proposta de aproveitamento de fibras vegetais para utilização em desenvolvimento de compósitos de matriz polimérica reforçados pelas mesmas é a motivação da pesquisa visando obter um compósito com melhores propriedades mecânicas e químicas do que sua matéria prima. Por virtude da importância do desenvolvimento desses materiais, a caracterização mecânica da fibra, da matriz e, finalmente, do compósito através de ensaios destrutivos e não destrutivos é fundamental para estudo de sua aplicação. Após a obtenção dos dados, percebeu-se que a adição das fibras melhorou as propriedades mecânicas do compósito resultante. Mostrando, portanto, resultados promissores para o desenvolvimento desses materiais, promovendo assim um material mais barato e de melhor propriedade mecânica, além de uma alta leveza. Em suma, os resultados estão de acordo com o esperado, impulsionando assim um melhor estudo desses materiais, por exemplo, realizando outros ensaios, como ensaios de impacto.

Oct 30, 2017

By R. W. Waytulonis

New exhaust control techniques and devices may be necessary to meet future diesel particulate matter emission standards in underground coal mines. This paper reviews conventional work practices and devices used to control diesel exhaust emissions, and new techniques being tested by the Bureau of Mines. Discussions will center on important work practices and on the function and efficiency of exhaust after-treatment devices. An industry/government cooperative research project to develop and test an exhaust after-treatment system for part 36 equipment is also discussed.

Jan 1, 1990

By Tiago Rafael Ferreira de Brito

O presente trabalho comparou o desempenho do fosfato de zinco e do microfosfato de zinco, ambos com tecnologia dry-in-place para verificação do comportamento destes revestimentos frente à conformação mecânica, por meio do ensaio de embutimento Erichsen, método Nakazima e curvas limite de conformação (CLC). Foram estudadas chapas de aço-carbono grau EM e grau EEP G4 eletrozincadas e fosfatizadas. As chapas foram fosfatizadas empregando-se dois banhos: fosfato de zinco e microfosfato de zinco, ambos com tecnologia dry-in-place. A caracterização da morfologia dos fosfatos estudados por microscopia eletrônica de varredura mostrou que as camadas de fosfato de zinco não apresentaram formação de cristais, quando aplicadas por roll coater e as análises por EDS comprovaram a presença do elemento fósforo. O ensaio de embutimento Erichsen somado aos resultados obtidos nas curvas CLC demonstraram que o microfosfato exibiu desempenho melhor em comparação ao fosfato. A diferença entre os dois tipos de fosfato foi mensurável e evidenciou que a tecnologia dry-in-place colaborou com a produção de camadas fosfatizadas adequadas para a lubrificação durante o processo de conformação mecânica.

Aug 16, 2017

By Jéssica Vicente Luiz, Rayander Martins Pimenta, Everton Pedroza dos Santos

The Hybrid Pelletized Sinter (HPS) is a agglomeration process that involves the combination of conventional sintering and pelletizing techniques and can be used with the purpose of obtaining improvements in the agglomeration stage of iron ore, and one of the great advantages of the process is the use of a wide particle size range of the ore. In this way, the superfines of low-cost ores, which are improper in sintering, can be used in the HPS process for the formation of the quasi-particle. The use of HPS with the sintering plants of the industries presented throughout the study, enabled an increase in productivity, decreased fuel utilization and reduced slag formation in blast furnaces. Thus, the present study aims to present a review of the literature on the Hybrid Pelletized Sinter (HPS) process and its main characteristics, as well as the results obtained by the companies that adopted the process.

Oct 1, 2019

By Paula Maria Gomes Cunha Leão

Um modelo matemático tridimensional, via software Fluent 14.0, de modo a descrever o fluxo, em regime transiente e isotérmico dos fluidos escória e nitrogênio, foi utilizado para avaliar o comportamento de slag splashing em um convertedor a oxigênio com o propósito de reparar as regiões desgastadas do revestimento de trabalho deste reator. Para um dado padrão de sopro foi investigou-se o efeito de parâmetros tais como temperatura, densidade, viscosidade e tensão interfacial. Os resultados são comparados com dados de projeção disponíveis na literatura.

Aug 16, 2017

By Henrique de Siqueira Queiroz

A indústria mineral brasileira é uma das maiores produtoras de minério de ferro do mundo e as reservas do país estão cada vez com teores mais baixos. Por isso hoje são necessários estudos para viabilizar a explotação de jazidas de baixos teores. Utilizando-se de minérios mais pobres, faz-se necessário uma maior cominuição para beneficiamento do minério. Com uma menor granulometria do material, o processo de flotação passa a ter importante papel no beneficiamento por ser mais tolerável aos finos. O objetivo deste trabalho foi testar diferentes coletores catiônicos, especificamente aminas, utilizados na etapa de flotação reversa de um minério de ferro da região do Vale do Rio Pardo. As amostras utilizadas nos testes são provenientes da remoagem que, pelo circuito de beneficiamento, alimenta a flotação de finos. Foram testados como coletores as aminas EDA, EDA3 e EDA 3C da Clariant. A amina que obteve melhor desempenho foi a Flotigam EDA 3C que obteve concentrado final com 67,4% Fe e 1,76% de SiO2, e recuperação metalúrgica de ferro de 92,14%.

Aug 7, 2018

By Markus Aspiala, Fiseha Tesfaye, Pekka Taskinen

In this paper, the standard thermodynamic properties of Ag3Sb and Ag6Sb intermetallic compounds have been studied by the solid state EMF-method, using Ag+ ion conducting β- alumina and AgI. The intermetallic compounds were synthesized from pure substances in evacuated silica ampoules and their formation were confirmed by the SEM-EDS analyses. The EMF measurements were made on electrochemical cells of the type [Ag | β-alumina | Ag-Sb] and [Ag | AgI | Ag-Sb]. The usage of β-alumina electrolyte, in this study, enabled thermodynamic measurements of the Ag-Sb-intermetallic compounds above 710 K, hitherto unreported. Based on the new experimental data, thermodynamic properties of the Ag-Sb-intermetallic compounds have been determined. The obtained experimental values have been compared with the available literature data.

Jan 1, 2015